Silicon Labs

SI3233-C-FM - 38-QFN Programmable SLIC | Silicon Labs

MPN: SI3233-C-FM ✗ انتهى عمره الإنتاجي
3.13 V to 5.25 V Vdss 88 mA Id 38-pin QFN Package
الحد الأدنى للطلب: 1 |

SI3233-C-FM نظرة عامة

The Silicon Labs SI3233-C-FM is a single-channel software-programmable Subscriber Line Interface Codec (SLIC) designed for telecommunications line-card equipment. It provides an SPI interface to a host controller, integrates one telephone-line circuit, and operates from a 3.13 V to 5.25 V supply. The device is packaged in a 38-pin QFN package. Its programmable architecture supports internal balanced ringing up to 90 VPK, DTMF generation, integrated battery supply, and a codec interface for connected voice applications.

An SLIC is the analog front-end for a subscriber line. It converts between the voice-band telephone signal and a digital PCM or codec representation, while also handling line supervision, ringing, tone generation, and hook-state functions. In the telecommunications hierarchy, the SI3233-C-FM is a telecommunications interface IC and system-on-chip designed to reduce the component count of a single-channel line-card design. The external Si3201 companion is used with this ProSLIC family in reference applications.

Key features include SPI host control, one integrated line circuit, an 88 mA supply current, and software-configurable internal ringing rated to 90 VPK. Ringing capability is specified for 5 REN at 4 kft and 3 REN at 8 kft. The IC also generates DTMF tones and includes a lead-free status, making it suitable for modern subscriber-line and voice-access equipment requiring programmable line functions.

The SI3233-C-FM combines analog line-interface functions with host-programmable control. Firmware can configure ringing, tone generation, line supervision, and codec behavior through the SPI interface, allowing one device to serve multiple network requirements. This integration reduces external line-driver circuitry and gives the host processor direct control over subscriber-line signaling.

Typical uses include single-channel subscriber line access, voice-over-IP line cards, voice gateways, digital subscriber line equipment, and telephone line test systems. The 38-QFN package supports compact designs, while the 3.13 V to 5.25 V operating range is suitable for regulated 3.3 V and 5 V digital and analog systems.

Designers should pay close attention to the high-voltage ringing interface, external protection network, thermal dissipation, and the required companion circuitry. The line-facing pins must be isolated from logic ground according to the application reference design. Decoupling must be placed close to the supply pins, and the PCB layout must account for the exposed thermal pad and the high-voltage transient environment at the subscriber line.

This page organizes the SI3233-C-FM technical characteristics, procurement information, application context, and engineering considerations. It also distinguishes documented functionality from parameters that require confirmation against the manufacturer datasheet, helping engineers plan a compliant line-card design more efficiently.

بدائل مباشرة لـ SI3233-C-FM — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.

لا تتوفر بدائل متوافقة تمامًا لهذا المنتج.

اطلب بدائل

SI3233-C-FM المواصفات

Product Type Programmable Subscriber Line Interface Codec (SLIC)
الواجهة SPI
Number of Circuits 1
جهد التغذية 3.13 V to 5.25 V
تيار التغذية 88 mA
Power Dissipation 700 mW
درجة حرارة التشغيل 0°C to 70°C
العلبة 38-pin QFN
Ringing Voltage Up to 90 VPK
Ringing Load 5 REN at 4 kft
Extended Ringing Load 3 REN at 8 kft
Ringing Control Software-configurable internal balanced ringing
Tone Generation DTMF generation
Codec Interface Integrated
Lead-Free Status Lead Free
Surface Mounting Surface mount

دليل تكوين أطراف SI3233-C-FM 38-pin qfn

تكوين الأطراف لـ SI3233-C-FM (حزمة 38-pin qfn). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.

مخطط توزيع أطراف حزمة 38-pin qfn لـ SI3233-C-FM

لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ SI3233-C-FM.

راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.

التطبيقات النموذجية

SI3233-C-FM مناسب لـ 6 التطبيقs: Single-Channel Subscriber Line Access, Voice-over-IP Line Card, Telephone Line Test Equipment, Digital Subscriber Line Equipment, Voice Gateway Terminal, Industrial Voice Communication Module.

🌐

Single-Channel Subscriber Line Access

The SI3233-C-FM fits a one-line subscriber access board because it combines a single-channel SLIC, SPI host control, an integrated codec interface, and programmable ringing in one 38-pin QFN device. The 3.13 V to 5.25 V operating range is compatible with common 3.3 V and 5 V logic rails, while the 90 VPK internal ringing capability reduces the amount of external line-drive circuitry. Designers still need an approved protection network, line transformer or matching network as applicable, and host firmware for line supervision. PCB placement should keep high-voltage ringing paths separate from sensitive logic and provide the exposed thermal pad with an effective thermal path.

📞

Voice-over-IP Line Card

The SI3233-C-FM is useful for a compact voice-over-IP line card that must present a telephone-line interface to a host processor. Its SPI interface allows firmware-driven control of programmable balanced ringing, DTMF generation, codec behavior, and line supervision, while the single-circuit architecture keeps the design appropriate for a one-line endpoint. The 88 mA supply-current figure and 700 mW stated dissipation make power budgeting important when several cards share a chassis. Use the manufacturer reference circuit for protection, bypassing, grounding, and high-voltage isolation clearances to avoid compromising signal quality or compliance.

🔧

Telephone Line Test Equipment

The SI3233-C-FM can support programmable telephone-line testing because its ringing, DTMF, and supervision functions can be coordinated by an external host through SPI. Software control allows test sequences to vary ringing voltage, tone generation, and line-state behavior without redesigning the analog interface. The single-channel format is appropriate for a focused line analyzer or portable test fixture rather than a multiport production tester. Engineers should validate the 90 VPK ringing operating condition, use the specified protection components, and separate the line interface from sensitive test circuitry through appropriate isolation and grounding.

🌐

Digital Subscriber Line Equipment

The SI3233-C-FM is applicable to compact DSL and legacy voice-over-DSL equipment requiring one analog subscriber-line channel alongside digital processing. Its single SLIC circuit, SPI interface, programmable ringing up to 90 VPK, and integrated codec interface allow the host processor to manage subscriber signaling while supporting a regulated 3.3 V or 5 V environment. The 38-pin QFN package helps reduce board area, but thermal and layout work remain critical because the line interface combines logic and elevated ringing voltage. Follow the reference layout for exposed-pad grounding, bypass placement, surge protection, and copper routing around the line-facing pins.

📡

Voice Gateway Terminal

A voice gateway terminal can use the SI3233-C-FM when it needs a controlled PSTN-facing interface for one subscriber channel. The device handles programmable balanced ringing, DTMF generation, line supervision, and codec interfacing, allowing the gateway firmware to translate between telephone-line activity and host-side signaling. The single-circuit architecture is most effective in compact gateways, adapters, and branch equipment where one line per module is acceptable. The 3.13 V to 5.25 V supply range simplifies integration with standard telecom logic rails, while the 38-pin QFN package demands careful thermal-pad and high-voltage layout work.

🏭

Industrial Voice Communication Module

The SI3233-C-FM can be used in a controlled indoor voice communication module where one analog line channel is required and the equipment operates within 0°C to 70°C. Its SPI programming interface allows centralized configuration of ringing and DTMF behavior, while the integrated codec interface simplifies connection to a communications controller. The module designer must budget the 88 mA supply current, provide adequate copper area under the QFN thermal pad, and use the prescribed line protection network. Confirm environmental, regulatory, and reliability requirements for the finished product because the IC’s commercial operating-temperature range does not cover every industrial environment.

What is the SI3233-C-FM?
The SI3233-C-FM is a single-channel, software-programmable Subscriber Line Interface Codec from Silicon Labs. According to the manufacturer datasheet, it combines an SPI host interface, one telephone line circuit, programmable balanced ringing, DTMF generation, and a codec interface. It operates from 3.13 V to 5.25 V and is packaged in a 38-pin QFN package for compact subscriber-line equipment.
What is the operating voltage of SI3233-C-FM?
The SI3233-C-FM operates from 3.13 V to 5.25 V. According to the manufacturer datasheet specifications, this range supports regulated 3.3 V and 5 V systems. The device has a stated supply current of 88 mA and a rated power dissipation of 700 mW. Confirming the local bypass-capacitor values and layout against the datasheet reference circuit is essential for stable line-card operation.
How many telephone line circuits does SI3233-C-FM support?
The SI3233-C-FM supports one telephone line circuit. The manufacturer datasheet identifies it as a single-channel SLIC with an SPI interface and programmable internal ringing. It is therefore suited to one-line voice cards, voice gateways, and subscriber-line access equipment. For a multichannel line card, multiple devices or a multichannel SLIC family would normally be required instead of assuming that one SI3233-C-FM can handle multiple lines.
What ringing capability does SI3233-C-FM provide?
The SI3233-C-FM provides software-configurable internal balanced ringing up to 90 VPK. The manufacturer datasheet specifies 5 REN at 4 kft and 3 REN at 8 kft. These figures define the supported ringing load conditions and help engineers select the appropriate external protection, transformer, and line-interface components. The line-facing network still requires suitable transient protection and creepage design.
Where can I download the SI3233-C-FM datasheet PDF?
The SI3233-C-FM datasheet PDF can be downloaded from the source listed on this page or from the manufacturer product documentation when available. The document describes the SPI interface, single-channel SLIC architecture, programmable ringing up to 90 VPK, DTMF generation, supply range of 3.13 V to 5.25 V, and the 38-pin QFN package. Use the pin-description table and reference circuit for final PCB assignments.
Where can I find the SI3233-C-FM pinout?
The SI3233-C-FM pinout is identified in the manufacturer datasheet as a 38-pin QFN device with an exposed pad. Use the package drawing and pin-description table for exact numbering, signal names, exposed-pad connections, and NC assignments. The available 38-pin QFN package is not represented by a matching SVG key in the current package library, so the package diagram uses the generic library entry rather than implying a verified pin map.
Can the SI3233-C-FM generate DTMF tones?
Yes. The SI3233-C-FM includes DTMF generation as one of its programmable telephony signaling functions. According to the manufacturer datasheet, the same device also supports internal balanced ringing and codec interfacing, allowing the host to control telephone-line signaling through SPI. The exact tone levels, timing, and calibration procedure should be taken from the manufacturer’s register and test descriptions.
Is SI3233-C-FM suitable for voice-over-IP equipment?
The SI3233-C-FM is suitable for a single-channel voice-over-IP line card when the design requires a programmable telephone-line front end. Its SPI interface, codec interface, DTMF generation, and internal ringing up to 90 VPK support host-controlled voice and signaling functions. The device is not a complete voice codec system, so the host processor, line protection network, and approved external line-interface components remain necessary.
What can replace SI3233-C-FM?
A true drop-in replacement for the SI3233-C-FM must use the same 38-pin QFN footprint and preserve pin-level functionality, register compatibility, supply range, ringing behavior, and line-interface performance. The available cross-reference results do not identify a distinct part that satisfies those conditions without introducing a different package or materially different architecture. Treat the published SI3233-C-FMR designation as a packaging-related catalog variant rather than a different-engineering-value replacement.
What is the best cross-brand equivalent for SI3233-C-FM?
No confirmed cross-brand drop-in equivalent for the SI3233-C-FM is identified in the available technical references. A cross-brand candidate would need the same 38-pin QFN land pattern, compatible SPI host interface, 3.13 V to 5.25 V supply range, programmable ringing up to 90 VPK, and equivalent line-signaling behavior. Because these details are not documented for a specific competitor part, use the Request a Quote form when qualified sourcing support is required.
SI3233-C-FM versus a multichannel SLIC — which is better?
The SI3233-C-FM is better when the design needs exactly one subscriber line in a compact 38-pin QFN implementation. A multichannel SLIC is better when line density, shared infrastructure, or multiple independent channels justify its larger package and higher channel count. The SI3233-C-FM provides one circuit, SPI control, DTMF generation, and programmable ringing up to 90 VPK, so channel count should be the primary selection criterion.
When should I choose SI3233-C-FM instead of a multichannel SLIC?
Choose the SI3233-C-FM for a compact, single-line design that can be controlled through SPI and does not need integrated multi-channel routing. Its 38-pin QFN package, 3.13 V to 5.25 V supply range, and programmable telephone signaling suit compact voice gateways and line-card products. Choose a multichannel SLIC instead when several subscriber lines must share one device and board area is a secondary concern.
Is SI3233-C-FM suitable for industrial applications?
The SI3233-C-FM is suitable only when the final equipment meets its documented 0°C to 70°C operating-temperature range. Its 88 mA supply current, 700 mW stated power, single-circuit SLIC function, and programmable ringing make it appropriate for controlled indoor telecom environments. For wider industrial temperature ranges or stricter reliability qualifications, request an availability and qualification review through the Request a Quote form.
How much thermal dissipation does SI3233-C-FM require?
The manufacturer datasheet lists 700 mW as the device’s power dissipation. For layout planning, provide the exposed thermal pad with a low-resistance connection to ground and copper area according to the datasheet thermal guidance. The exact junction-temperature limit and package thermal resistance are not stated in the available specifications, so confirm both before calculating the maximum permitted ambient temperature.
Where to buy SI3233-C-FM online and what is the lead time?
Use the Request a Quote form on this page to request SI3233-C-FM availability, current pricing, lot information, and lead time. Stock status and delivery timing can change by quantity, packaging, and manufacturing condition, so they should be confirmed for the exact order. The Request a Quote form is the appropriate commercial channel for this single-channel telecom interface IC.
What are the key specifications of SI3233-C-FM that engineers should know?
The SI3233-C-FM is a 38-pin QFN, single-channel programmable SLIC with an SPI interface. According to the manufacturer datasheet, key specifications include a 3.13 V to 5.25 V supply range, 88 mA supply current, 700 mW power dissipation, 0°C to 70°C operating temperature, software-configurable balanced ringing up to 90 VPK, DTMF generation, an integrated codec interface, and a lead-free status.

بيانات مرجعية هندسية لـ SI3233-C-FM — المقارنة وإرشادات التصميم ومعلومات الامتثال.

دليل الاختيار

Choose the SI3233-C-FM when a design needs exactly one subscriber line, a SPI-programmable SLIC, DTMF generation, and integrated balanced ringing up to 90 VPK in a 38-pin QFN package. It is particularly suitable for compact voice gateways, one-line access cards, and voice-over-IP modules whose equipment remains within the 0°C to 70°C range. Select a multichannel SLIC when several lines must be integrated and reduced per-channel board area matters more than a compact single-line solution. Do not substitute a different package or a generic telecom interface without a complete pin, register, voltage, ringing, and timing review. The available technical references do not establish five distinct drop-in alternatives, so the most defensible sourcing strategy is to qualify the exact ordered SI3233-C-FM rather than rely on an unverified cross-reference.

المقارنة مع البدائل

المعامل هذا المنتج
Package 38-pin QFN
Brand Silicon Labs
Product Type Single-channel programmable SLIC
Number of Circuits 1
Host Interface SPI
Supply Voltage 3.13 V to 5.25 V
Supply Current 88 mA
Power Dissipation 700 mW
Operating Temperature 0°C to 70°C
Ringing Voltage Up to 90 VPK
Tone Generation DTMF generation
Lead-Free Status Lead Free

أبرز الفروقات

  • Integrated single-channel telephony function (مقابلSI3010-FSR)
  • Programmable ringing through the host interface (مقابلSI3233-C-FMR)
  • Compact mixed-signal integration (مقابلDS26524GNA5)

ملاحظات التصميم

Place the supply bypass capacitors and their ground returns directly beside the appropriate power and ground pins, following the manufacturer reference layout. The QFN exposed pad should connect to the intended thermal and electrical ground plane with short, low-impedance vias. Keep the 90 VPK line-facing routing away from low-level signal paths, and provide the required copper spacing and protection components around subscriber-line connections.

Budget at least the documented 88 mA supply current for normal device operation and use the 700 mW power figure as an additional thermal-design check. The actual converter capacity must also cover local analog and digital loads without causing supply droop during ringing or DTMF transitions. Confirm whether the host board uses 3.3 V or 5 V and verify that the selected operating point stays inside the 3.13 V to 5.25 V range.

Do not treat a same-family catalog suffix as an automatic drop-in replacement without checking the ordering code, package, pinout, and exposed-pad details. Also avoid substituting generic ringing controllers or transceivers for this device: the SI3233-C-FM combines SLIC, codec, SPI control, ringing, and DTMF functions. Validate surge protection, line loading, and firmware configuration against the manufacturer reference design before production release.

The device is rated at 700 mW power dissipation, so provide sufficient exposed-pad copper and thermal vias to spread heat into the PCB. Because the available documentation does not state the package thermal resistance or maximum junction temperature, obtain those limits before deriving an allowed ambient temperature. Consider the effect of neighboring regulators and enclosure temperature when sizing the thermal path.

معلومات الامتثال

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
خالٍ من الرصاص
Yes
خالٍ من الهالوجين
Unknown
المعادن المتنازع عليها
Unknown

The manufacturer datasheet snippet identifies the SI3233-C-FM as lead free. RoHS, REACH, halogen-free, and conflict-minerals status were not stated in the available technical data and therefore remain unknown. AEC-Q100 is not applicable to this telecommunications interface IC.

تم التحقق من البيانات في: 2026-11-16 — تم التحقق من البيانات وتنسيقها بواسطة فريق هندسة المكونات في XAIPART

عمليات بحث ذات صلة

SI3233-C-FM datasheet SI3233-C-FM pinout SI3233-C-FM datasheet pdf SI3233-C-FM replacement SI3233-C-FM equivalent SI3233-C-FM cross reference SI3233-C-FM price SI3233-C-FM stock Silicon Labs SI3233-C-FM SI3233-C-FM 38-QFN SI3233-C-FM 90 VPK ringing SI3233-C-FM voice gateway SI3233-C-FM vs SI3010-FSR SI3233-C-FM SPI SLIC SI3233-C-FM application circuit

المكونات والمصطلحات ذات الصلة

Silicon Labs SI3233-C-FM SI3233-C-FMR SI3010-FSR Subscriber Line Interface Codec SLIC ProSLIC software-programmable SLIC telecommunications interface IC SPI codec interface DTMF generation balanced ringing 90 VPK ringing 5 REN 4 kft line 38-pin QFN surface mount semiconductor voice-over-IP subscriber line access line supervision Silicon Labs Si3201 RoHS REACH
عرض سعر سريع RFQ
املأ التفاصيل الكاملة — سيرد فريق المبيعات لدينا خلال 24 ساعة
رقم القطعة الشركة المصنعة الحزمة QTY السعر المستهدف الإجمالي
✓
تم إرسال عرض السعر!

سنرد على بريدك الإلكتروني خلال 24 ساعة

1
تم إرسال طلب عرض السعر
2
تم استلام عرض السعر
3
تم تقديم الطلب
4
الدفع
5
تم الشحن
6
تم التسليم
عرض تفاصيل طلب عرض السعر