STMicroelectronics

STM32L451CCU3 - 80MHz Cortex-M4 256KB MCU | STMicroelectronics

MPN: STM32L451CCU3 ✓ نشط
48-pin UFQFPN, 7 x 7 mm Package 80 MHz Speed 256 KB Memory
الحد الأدنى للطلب: 1 |

STM32L451CCU3 نظرة عامة

The STMicroelectronics STM32L451CCU3 is an ultra-low-power 32-bit microcontroller based on the Arm Cortex-M4 RISC core, operating up to 80 MHz with 256 KB of Flash memory in a 48-pin UFQFPN 7 x 7 mm package. It combines a compact embedded design with extensive serial connectivity, low-power operating modes, and a hardware floating-point unit.

An ultra-low-power microcontroller is an embedded semiconductor designed to execute firmware while minimizing energy consumption during idle, sleep, stop, and standby operation. The STM32L4 series belongs to the microcontroller hierarchy that includes 32-bit RISC processors, embedded processors, and energy-conscious IoT control devices. This makes the STM32L451CCU3 suitable for connected sensors, compact industrial modules, and portable equipment in which board area and average power are important design constraints.

Key characteristics include an Arm Cortex-M4 core with single-precision floating-point support, 256 KB of Flash, up to 80 MHz operation, and an Arm Cortex-M4-based architecture optimized for energy-efficient embedded processing. The device also provides a broad set of serial interfaces and is identified as supporting DFSDM functionality. Its 48-pin UFQFPN package permits a compact PCB footprint while exposing the peripheral connections required by communications, control, and analog-signal-processing designs.

The STM32L451CCU3 combines conventional microcontroller processing with energy-saving low-power modes and extensive clock-management options. The 256 KB Flash capacity provides room for application firmware, configuration data, and boot code, while the Cortex-M4 floating-point unit accelerates control calculations that would otherwise require software emulation. Its 80 MHz maximum operating frequency supports responsive control loops, communication protocol handling, and moderate real-time processing tasks.

Typical applications include industrial sensor nodes, low-power IoT gateways, compact motor and actuator controllers, digital power-conversion controllers, and battery-powered portable instruments. The 48-pin package is particularly useful when a design needs more GPIO and peripheral connectivity than a small leadless MCU package normally provides, while still avoiding the size of a large plastic-leaded package.

Designers should verify power-supply limits, operating-temperature grade, pin multiplexing, exposed-pad layout, and decoupling requirements against the STM32L451CC datasheet and reference documentation. Correct PCB implementation of the 48-pin UFQFPN footprint, thermal-pad connection, and high-speed signal return paths is essential for reliable operation.

This page consolidates the manufacturer specifications, package information, sourcing context, and engineering guidance for the STM32L451CCU3. It also distinguishes temperature-grade and family alternatives while identifying which comparisons require firmware and board-level validation before substitution.

بدائل مباشرة لـ STM32L451CCU3 — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.

STM32L451CCU6TR

✅ بديل مباشر
📦 48-pin UFQFPN, 7 x 7 mm
Same 48-pin UFQFPN footprint and 256 KB Flash family configuration; the U6 ordering suffix differs from U3 and requires temperature-grade validation.

📋 بديل مرجعي (غير موجود في الكتالوج)

STM32L451CCU3 الحدود القصوى والخصائص الكهربائية

Product Type 32-bit ultra-low-power microcontroller
Processor Core Arm Cortex-M4 32-bit RISC core
Maximum CPU Frequency 80 MHz
Flash Memory 256 KB
Flash Organization 256K x 8 bits
FPU Single-precision floating-point unit
العلبة 48-pin UFQFPN, 7 x 7 mm
نوع التركيب Surface mount
DFSDM Support Yes
أقصى تردد للساعة 80 MHz

دليل تكوين أطراف STM32L451CCU3 48-pin ufqfpn, 7 x 7 mm

تكوين الأطراف لـ STM32L451CCU3 (حزمة 48-pin ufqfpn, 7 x 7 mm). تتضمن هذه الدائرة المتكاملة الرقمية GPIO وواجهات الاتصال (UART وSPI وI2C) وأطراف الطاقة. راجع ورقة بيانات الشركة المصنعة لوظائف الأطراف البديلة وخيارات التكوين. ضرورية لتصميم الأنظمة المدمجة وتخطيط PCB.

مخطط توزيع أطراف حزمة 48-pin ufqfpn, 7 x 7 mm لـ STM32L451CCU3

لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ STM32L451CCU3.

راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.

التطبيقات النموذجية

STM32L451CCU3 مناسب لـ 6 التطبيقs: Industrial Sensor Nodes, Low-Power IoT Gateways, Digital Power Controllers, Compact Motor Controllers, Portable Medical Instruments, Battery-Powered Data Loggers.

🏭

Industrial Sensor Nodes

The STM32L451CCU3 fits industrial sensor nodes that need local signal conditioning, configuration handling, and low-power control in a compact assembly. Its 80 MHz Arm Cortex-M4 core can execute protocol stacks and supervisory logic while the floating-point unit accelerates filtering and compensation calculations. The 256 KB Flash capacity provides room for application code and calibration parameters. In a typical design, the MCU interfaces with sensors through digital or analog peripherals and communicates results over an industrial network. System-level power optimization depends on duty-cycling the sensor and communications circuitry rather than relying only on the MCU rating.

🧩

Low-Power IoT Gateways

The STM32L451CCU3 is suitable for compact IoT gateway controllers that aggregate readings from multiple sensors and maintain low activity between transmissions. Its ultra-low-power STM32L4 architecture supports energy-conscious operation, while the Cortex-M4 core at up to 80 MHz handles local logic and communication framing. The 256 KB Flash supports firmware, protocol handlers, and configuration storage without requiring a larger package. In an implementation, the MCU can remain in a low-power state until a sensor interrupts it, process the event, transmit the result, and return to sleep.

⚡

Digital Power Controllers

The STM32L451CCU3 can serve as the digital controller in compact power-conversion systems where responsive control, PWM generation, and analog monitoring are required. Its Cortex-M4 processor reaches up to 80 MHz, allowing control calculations and supervisory tasks to execute efficiently, while the hardware floating-point unit accelerates compensation and filtering mathematics. The 256 KB Flash is suitable for control code, parameter tables, and fault-handling routines. A practical design should allocate pins for high-resolution PWM, feedback ADC channels, fault signals, and an external communication interface while preserving short analog return paths.

🔧

Compact Motor Controllers

The STM32L451CCU3 is appropriate for compact motor controllers that benefit from a high-performance Cortex-M4 core and hardware floating-point processing. At up to 80 MHz, the MCU can execute current-control and speed-control loops, perform fault management, and manage communications concurrently. The 256 KB Flash provides room for application firmware and tuning parameters. In a motor-control board, the MCU compares current and position feedback, updates PWM outputs, applies limits, and reports exceptions through a serial interface. Mechanical and electrical timing requirements must be checked against the device timer and analog-conversion resources.

💊

Portable Medical Instruments

The STM32L451CCU3 can support portable medical-instrument signal paths that require compact processing, local calculations, and controlled power consumption. Its Cortex-M4 FPU supports efficient numerical operations, and the 256 KB Flash can hold control firmware, self-test routines, and interface protocols. The device can supervise sensor acquisition, apply digital filtering, manage a local display or communications interface, and record diagnostic events. Medical use requires a system-level risk assessment, validation of measurement accuracy, isolation review, and confirmation that the selected device condition satisfies the applicable quality requirements.

📱

Battery-Powered Data Loggers

The STM32L451CCU3 fits battery-powered data loggers because its ultra-low-power STM32L4 architecture can combine responsive processing with reduced activity in unattended applications. The 80 MHz Cortex-M4 core handles sensor coordination, timestamp logic, data compression, and configuration, while 256 KB Flash supports firmware and local data structures. A logger may wake periodically, acquire a sample, append it to nonvolatile storage, and return to a low-power state. Battery-life calculations should include sensor standby current, storage-energy per write, regulator quiescent current, and the duration of each active measurement cycle.

What is the STM32L451CCU3?
The STM32L451CCU3 is an ultra-low-power 32-bit microcontroller from STMicroelectronics built around an Arm Cortex-M4 RISC core. According to the STMicroelectronics STM32L451CC product page, it operates at up to 80 MHz, provides 256 KB of Flash, and is offered in a 48-pin UFQFPN package measuring 7 x 7 mm. It is intended for compact embedded systems requiring efficient processing, low-power operating modes, and extensive peripheral integration.
What is the operating voltage range of the STM32L451CCU3?
The STM32L451CCU3 operating-voltage range must be taken from the manufacturer datasheet for the exact ordering code. The STMicroelectronics product page confirms an 80 MHz Cortex-M4 microcontroller with 256 KB of Flash, but it does not expose the complete electrical limit in the cited product summary. Use the STM32L451CC datasheet tables for minimum, maximum, and recommended supply voltages, including any restrictions that apply to power-saving modes or analog operation.
What are the key specifications of STM32L451CCU3 that engineers should know?
The STM32L451CCU3 combines an 80 MHz Arm Cortex-M4 core, 256 KB of Flash, single-precision floating-point support, DFSDM capability, and a 48-pin UFQFPN package. According to the STMicroelectronics STM32L451CC product page, the device is an ultra-low-power member of the STM32L4 family. Its main engineering benefit is the combination of 32-bit real-time processing and a compact 7 x 7 mm footprint for low-power embedded products.
Where can I download the STM32L451CCU3 datasheet PDF?
The STM32L451CCU3 datasheet and supporting technical documents are available from the official STMicroelectronics STM32L451CC product page. That page provides the manufacturer’s technical documentation for the STM32L451xx device family, which includes the STM32L451CCU3 ordering code. For PCB work, also consult the package drawing, pin definitions, electrical characteristics, and reference manual associated with the selected device revision.
Where can I find the STM32L451CCU3 pinout?
The STM32L451CCU3 pin assignment is documented in the STM32L451CC datasheet and its associated package information. The device uses a 48-pin UFQFPN package with an exposed thermal pad, so the footprint cannot be reproduced accurately from a generic 48-pin drawing. Use the manufacturer pin-definition table when allocating GPIO, power, ground, analog, debug, and communication signals, and preserve the exposed-pad land pattern specified for the board stack-up.
Is STM32L451CCU3 suitable for low-power IoT devices?
Yes, the STM32L451CCU3 is suitable for low-power IoT and industrial sensor designs because it belongs to STMicroelectronics’ ultra-low-power STM32L4 family. Its Arm Cortex-M4 core runs at up to 80 MHz and includes single-precision floating-point hardware for responsive local processing. Final battery-life calculations must include the selected radio, sensor duty cycle, regulator efficiency, and the exact STM32L4 low-power mode selected for the application.
What can replace the STM32L451CCU3?
The closest documented same-family option is the STM32L451CCU6TR, which uses the same 48-pin UFQFPN class and 256 KB Flash configuration but represents a different ordering suffix and temperature-grade code. It should not be substituted without checking pin functions, supply limits, temperature range, exposed-pad layout, and qualification requirements. Cross-brand Cortex-M4 devices can differ in firmware, peripherals, clock behavior, and tool support even when their packages appear identical.
Can STM32L451CCU6TR replace STM32L451CCU3?
The STM32L451CCU6TR is a pin-footprint candidate for the STM32L451CCU3 because both belong to the STM32L451CC family and use a 48-pin UFQFPN package, but the ordering codes must still be compared for qualification and temperature-grade differences. The “U3” and “U6” suffixes encode different device conditions, and the trailing “TR” identifies tape-and-reel shipping format. Validate the complete ordering code before committing to a replacement.
STM32L451CCU3 vs STM32L451CCU6TR — which is better?
Choose the STM32L451CCU3 when its specified temperature grade and orderable packaging meet the product requirements. Consider the STM32L451CCU6TR when that suffix provides the required device condition or packaging and the manufacturer confirms the exact ordering-code differences. Both target the same STM32L451CC family and 48-pin UFQFPN class, but suffix changes can affect temperature range, qualification, and logistics rather than the basic Cortex-M4 architecture.
When should I choose STM32L451CCU3 over a lower-pin-count STM32L4?
Choose the STM32L451CCU3 when the design needs the balance of 256 KB Flash, up to 80 MHz processing, DFSDM support, and a 48-pin UFQFPN interface set within a compact 7 x 7 mm footprint. A lower-pin-count device may be preferable when fewer GPIO or peripheral connections are required, or when minimizing package size and board complexity is more important than the STM32L451CCU3’s connection density.
Is STM32L451CCU3 appropriate for motor and power control?
The STM32L451CCU3 is appropriate for many compact motor-control and digital power-control designs because it combines an 80 MHz Arm Cortex-M4 core with single-precision floating-point acceleration and 256 KB of Flash. The Cortex-M4 FPU can simplify control-loop mathematics without software floating-point emulation. Final suitability depends on the required PWM resolution, fast-switching interfaces, ADC timing, timer resources, safety functions, and thermal design.
How much power does the STM32L451CCU3 consume?
The STM32L451CCU3 is designed for low-power operation, but its consumption depends on supply voltage, CPU activity, peripheral activity, clock configuration, and the selected operating mode. Use the current-consumption tables in the manufacturer datasheet for each characterized mode rather than assuming one universal current value. Board-level energy calculations must additionally include regulator losses, pull-up networks, sensors, communications, and indicator loads.
Can I use the same PCB footprint for STM32L451CCU3 and STM32L451CCU6TR?
The STM32L451CCU3 and STM32L451CCU6TR use the same 48-pin UFQFPN package class, so their land patterns and exposed-pad designs are candidates for reuse. Before committing a PCB revision, compare the manufacturer drawings for pad dimensions, mask-defined versus solderable exposed pads, pin numbering, and paste volume. Also confirm that electrical ratings, temperature grade, qualification, and firmware assumptions remain acceptable.
What tooling supports the STM32L451CCU3?
The STM32L451CCU3 is an Arm Cortex-M4 MCU and is supported by the STM32 development, programming, and debugging ecosystem. Typical workflows use an ST-LINK debugger and STM32CubeIDE or STM32CubeProgrammer, with board configuration and peripheral initialization handled through STM32CubeMX. The manufacturer documentation should be consulted for supported access-protocol debuggers, SWD/JTAG configuration, boot modes, and production-programming recommendations.
Where to buy STM32L451CCU3 online?
Use the “Request a Quote” form on this page to request STM32L451CCU3 availability, quantity breaks, lead time, and shipment options. The exact ordering-code availability can vary by package condition and regional inventory. Provide the target quantity, acceptable delivery date, and whether the order must be reel, tray, or another approved packing format so the sourcing request can be handled accurately.
What is the price and lead time of STM32L451CCU3?
Submit a quote request through the “Request a Quote” form on this page for the current STM32L451CCU3 price and lead time. Quote terms can depend on quantity, package condition, authorized distribution, production schedule, and destination. The form should receive the required quantity and desired delivery date so current commercial data can be matched to the specific STM32L451CCU3 ordering code rather than to a broader STM32L451 family listing.

بيانات مرجعية هندسية لـ STM32L451CCU3 — المقارنة وإرشادات التصميم ومعلومات الامتثال.

دليل الاختيار

Choose the STM32L451CCU3 when the exact ordering condition, temperature grade, qualification level, and package format meet the product requirements. Its 80 MHz Cortex-M4 core, 256 KB of Flash, DFSDM support, and 48-pin UFQFPN footprint make it appropriate for compact industrial sensing, low-power IoT control, portable instruments, and digital power applications. Consider the STM32L451CCU6TR when the manufacturer confirms that its device condition and packaging are preferable for the production program; its shared family architecture and package support board reuse, but the suffix and trailing TR code must be reconciled with the original BOM. For cross-brand or lower-pin-count alternatives, treat them as new design decisions rather than automatic replacements because peripheral mapping, clock behavior, firmware, qualification, and low-power characteristics can differ.

المقارنة مع البدائل

المعامل هذا المنتج STM32L451CCU6TR
Brand STMicroelectronics STMicroelectronics
Package 48-pin UFQFPN, 7 x 7 mm 48-pin UFQFPN, 7 x 7 mm
Processor Core Arm Cortex-M4 32-bit RISC core Arm Cortex-M4 32-bit RISC core
Maximum CPU Frequency 80 MHz 80 MHz
Flash Memory 256 KB 256 KB
Product Family STM32L451CC STM32L451CC
DFSDM Support Yes Yes
Ordering Suffix CCU3 CCU6TR

أبرز الفروقات

  • Compact processing density (مقابلSTM32L451CCU6TR)
  • Same-family pin compatibility path (مقابلSTM32L451CCU6TR)
  • Integrated floating-point acceleration (مقابلSTM32L451CCU6TR)

ملاحظات التصميم

Implement the STM32L451CCU3 as a 48-pin UFQFPN layout using the manufacturer’s land pattern and exposed-pad recommendations. Confirm pad dimensions, solder-mask definition, paste volume, and annular-ring requirements against the PCB process capability. Place input and bulk decoupling capacitors close to their associated power pins, provide a low-impedance ground return, and route high-current or fast-switching nets away from sensitive analog inputs to minimize coupled noise.

Preserve short, continuous return paths for clocks, debug signals, and communication interfaces. The Cortex-M4 debug port can normally be used for programming and diagnostics, but the board should still follow the manufacturer’s debug-signal layout guidance. Where the package exposes an exposed thermal pad, connect it to the intended ground or power structure specified by the datasheet rather than treating it as an unspecified mechanical pad.

Do not select a substitute solely by matching the UFQFPN package and 256 KB Flash size. The STM32L451CCU3 and STM32L451CCU6TR differ in ordering suffix, and the trailing TR code denotes tape-and-reel packaging. Before substitution, verify pin multiplexing, supply-voltage limits, temperature grade, qualification, exposed-pad implementation, clock tree, peripheral inventory, bootloader behavior, and firmware assumptions.

Low-power operation depends on the complete board, not only the MCU core current. Account for regulator quiescent current, sensor standby consumption, pull networks, communication activity, and leakage paths. Measure sleep-state current with peripherals in their intended states, and validate wake timing, retained state, oscillator startup, and peripheral initialization after every low-power transition.

معلومات الامتثال

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
خالٍ من الرصاص
Unknown
خالٍ من الهالوجين
Unknown
المعادن المتنازع عليها
Unknown

Compliance status requires confirmation from the manufacturer’s current product documentation and material declaration for the exact ordering code.

تم التحقق من البيانات في: 2026-11-19 — تم التحقق من البيانات وتنسيقها بواسطة فريق هندسة المكونات في XAIPART

عمليات بحث ذات صلة

STM32L451CCU3 datasheet STM32L451CCU3 pinout STM32L451CCU3 datasheet pdf STM32L451CCU3 equivalent STM32L451CCU3 replacement STM32L451CCU3 footprint STM32L451CCU3 schematic STM32L451CCU3 programming STM32L451CCU3 price STM32L451CCU3 stock STMicroelectronics STM32L451CCU3 STM32L451CCU3 vs STM32L451CCU6TR STM32L451CCU3 48 pin UFQFPN STM32L451CCU3 80MHz Cortex-M4 STM32L451CCU3 application circuit

المكونات والمصطلحات ذات الصلة

STMicroelectronics STM32L451CCU3 STM32L451CCU6TR STM32L451CC Arm Cortex-M4 32-bit RISC core ultra-low-power microcontroller embedded microcontroller IoT control device single-precision floating-point unit DFSDM 256 KB Flash 80 MHz 48-pin UFQFPN 7 x 7 mm package QFN family surface mount SMD STM32CubeIDE STM32CubeProgrammer SWD debug industrial sensor node digital power control motor controller battery-powered data logger
عرض سعر سريع RFQ
املأ التفاصيل الكاملة — سيرد فريق المبيعات لدينا خلال 24 ساعة
رقم القطعة الشركة المصنعة الحزمة QTY السعر المستهدف الإجمالي
✓
تم إرسال عرض السعر!

سنرد على بريدك الإلكتروني خلال 24 ساعة

1
تم إرسال طلب عرض السعر
2
تم استلام عرض السعر
3
تم تقديم الطلب
4
الدفع
5
تم الشحن
6
تم التسليم
عرض تفاصيل طلب عرض السعر