STM32L451CCU3 - 80MHz Cortex-M4 256KB MCU | STMicroelectronics
MPN: STM32L451CCU3 ✓ AktifSTM32L451CCU3 Genel Bakış
An ultra-low-power microcontroller is an embedded semiconductor designed to execute firmware while minimizing energy consumption during idle, sleep, stop, and standby operation. The STM32L4 series belongs to the microcontroller hierarchy that includes 32-bit RISC processors, embedded processors, and energy-conscious IoT control devices. This makes the STM32L451CCU3 suitable for connected sensors, compact industrial modules, and portable equipment in which board area and average power are important design constraints.
Key characteristics include an Arm Cortex-M4 core with single-precision floating-point support, 256 KB of Flash, up to 80 MHz operation, and an Arm Cortex-M4-based architecture optimized for energy-efficient embedded processing. The device also provides a broad set of serial interfaces and is identified as supporting DFSDM functionality. Its 48-pin UFQFPN package permits a compact PCB footprint while exposing the peripheral connections required by communications, control, and analog-signal-processing designs.
The STM32L451CCU3 combines conventional microcontroller processing with energy-saving low-power modes and extensive clock-management options. The 256 KB Flash capacity provides room for application firmware, configuration data, and boot code, while the Cortex-M4 floating-point unit accelerates control calculations that would otherwise require software emulation. Its 80 MHz maximum operating frequency supports responsive control loops, communication protocol handling, and moderate real-time processing tasks.
Typical applications include industrial sensor nodes, low-power IoT gateways, compact motor and actuator controllers, digital power-conversion controllers, and battery-powered portable instruments. The 48-pin package is particularly useful when a design needs more GPIO and peripheral connectivity than a small leadless MCU package normally provides, while still avoiding the size of a large plastic-leaded package.
Designers should verify power-supply limits, operating-temperature grade, pin multiplexing, exposed-pad layout, and decoupling requirements against the STM32L451CC datasheet and reference documentation. Correct PCB implementation of the 48-pin UFQFPN footprint, thermal-pad connection, and high-speed signal return paths is essential for reliable operation.
This page consolidates the manufacturer specifications, package information, sourcing context, and engineering guidance for the STM32L451CCU3. It also distinguishes temperature-grade and family alternatives while identifying which comparisons require firmware and board-level validation before substitution.
Drop-in alternatifler için STM32L451CCU3 — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
STM32L451CCU6TR
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
STM32L451CCU3 Maksimum Değerlendirmeler & Elektriksel Özellikler
| Product Type | 32-bit ultra-low-power microcontroller |
| Processor Core | Arm Cortex-M4 32-bit RISC core |
| Maximum CPU Frequency | 80 MHz |
| Flash Memory | 256 KB |
| Flash Organization | 256K x 8 bits |
| FPU | Single-precision floating-point unit |
| Paket | 48-pin UFQFPN, 7 x 7 mm |
| Montaj Türü | Surface mount |
| DFSDM Support | Yes |
| Azami Saat Hızı | 80 MHz |
STM32L451CCU3 48-pin ufqfpn, 7 x 7 mm Pin Yapısı Kılavuzu
STM32L451CCU3 (48-pin ufqfpn, 7 x 7 mm paket) için pin yapısı. Bu dijital IC, GPIO, iletişim arayüzleri (UART, SPI, I2C) ve güç pinleri içerir. Alternatif pin işlevleri ve yapılandırma seçenekleri için üretici veri kitapçığını referans alın. Tünel sistem tasarımı ve PCB yerleşimi için temel bir bileşendir.
Ayrıntılı pin çıkış verisi mevcut değil: STM32L451CCU3.
Aşağıdaki veri sayfası tam pin konfigürasyonu için.
Tipik Uygulamalar
STM32L451CCU3 için uygundur 6 uygulamas: Industrial Sensor Nodes, Low-Power IoT Gateways, Digital Power Controllers, Compact Motor Controllers, Portable Medical Instruments, Battery-Powered Data Loggers.
Industrial Sensor Nodes
The STM32L451CCU3 fits industrial sensor nodes that need local signal conditioning, configuration handling, and low-power control in a compact assembly. Its 80 MHz Arm Cortex-M4 core can execute protocol stacks and supervisory logic while the floating-point unit accelerates filtering and compensation calculations. The 256 KB Flash capacity provides room for application code and calibration parameters. In a typical design, the MCU interfaces with sensors through digital or analog peripherals and communicates results over an industrial network. System-level power optimization depends on duty-cycling the sensor and communications circuitry rather than relying only on the MCU rating.
Önerilen
Low-Power IoT Gateways
The STM32L451CCU3 is suitable for compact IoT gateway controllers that aggregate readings from multiple sensors and maintain low activity between transmissions. Its ultra-low-power STM32L4 architecture supports energy-conscious operation, while the Cortex-M4 core at up to 80 MHz handles local logic and communication framing. The 256 KB Flash supports firmware, protocol handlers, and configuration storage without requiring a larger package. In an implementation, the MCU can remain in a low-power state until a sensor interrupts it, process the event, transmit the result, and return to sleep.
Önerilen
Digital Power Controllers
The STM32L451CCU3 can serve as the digital controller in compact power-conversion systems where responsive control, PWM generation, and analog monitoring are required. Its Cortex-M4 processor reaches up to 80 MHz, allowing control calculations and supervisory tasks to execute efficiently, while the hardware floating-point unit accelerates compensation and filtering mathematics. The 256 KB Flash is suitable for control code, parameter tables, and fault-handling routines. A practical design should allocate pins for high-resolution PWM, feedback ADC channels, fault signals, and an external communication interface while preserving short analog return paths.
Önerilen
Compact Motor Controllers
The STM32L451CCU3 is appropriate for compact motor controllers that benefit from a high-performance Cortex-M4 core and hardware floating-point processing. At up to 80 MHz, the MCU can execute current-control and speed-control loops, perform fault management, and manage communications concurrently. The 256 KB Flash provides room for application firmware and tuning parameters. In a motor-control board, the MCU compares current and position feedback, updates PWM outputs, applies limits, and reports exceptions through a serial interface. Mechanical and electrical timing requirements must be checked against the device timer and analog-conversion resources.
Önerilen
Portable Medical Instruments
The STM32L451CCU3 can support portable medical-instrument signal paths that require compact processing, local calculations, and controlled power consumption. Its Cortex-M4 FPU supports efficient numerical operations, and the 256 KB Flash can hold control firmware, self-test routines, and interface protocols. The device can supervise sensor acquisition, apply digital filtering, manage a local display or communications interface, and record diagnostic events. Medical use requires a system-level risk assessment, validation of measurement accuracy, isolation review, and confirmation that the selected device condition satisfies the applicable quality requirements.
Önerilen
Battery-Powered Data Loggers
The STM32L451CCU3 fits battery-powered data loggers because its ultra-low-power STM32L4 architecture can combine responsive processing with reduced activity in unattended applications. The 80 MHz Cortex-M4 core handles sensor coordination, timestamp logic, data compression, and configuration, while 256 KB Flash supports firmware and local data structures. A logger may wake periodically, acquire a sample, append it to nonvolatile storage, and return to a low-power state. Battery-life calculations should include sensor standby current, storage-energy per write, regulator quiescent current, and the duration of each active measurement cycle.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: STM32L451CCU3 — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | STM32L451CCU6TR |
|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics |
| Package | 48-pin UFQFPN, 7 x 7 mm | 48-pin UFQFPN, 7 x 7 mm |
| Processor Core | Arm Cortex-M4 32-bit RISC core | Arm Cortex-M4 32-bit RISC core |
| Maximum CPU Frequency | 80 MHz | 80 MHz |
| Flash Memory | 256 KB | 256 KB |
| Product Family | STM32L451CC | STM32L451CC |
| DFSDM Support | Yes | Yes |
| Ordering Suffix | CCU3 | CCU6TR |
Ana Farklılayıcılar
- Compact processing density (karşılaştırma:STM32L451CCU6TR)
- Same-family pin compatibility path (karşılaştırma:STM32L451CCU6TR)
- Integrated floating-point acceleration (karşılaştırma:STM32L451CCU6TR)
Tasarım Notları
Implement the STM32L451CCU3 as a 48-pin UFQFPN layout using the manufacturer’s land pattern and exposed-pad recommendations. Confirm pad dimensions, solder-mask definition, paste volume, and annular-ring requirements against the PCB process capability. Place input and bulk decoupling capacitors close to their associated power pins, provide a low-impedance ground return, and route high-current or fast-switching nets away from sensitive analog inputs to minimize coupled noise.
Preserve short, continuous return paths for clocks, debug signals, and communication interfaces. The Cortex-M4 debug port can normally be used for programming and diagnostics, but the board should still follow the manufacturer’s debug-signal layout guidance. Where the package exposes an exposed thermal pad, connect it to the intended ground or power structure specified by the datasheet rather than treating it as an unspecified mechanical pad.
Do not select a substitute solely by matching the UFQFPN package and 256 KB Flash size. The STM32L451CCU3 and STM32L451CCU6TR differ in ordering suffix, and the trailing TR code denotes tape-and-reel packaging. Before substitution, verify pin multiplexing, supply-voltage limits, temperature grade, qualification, exposed-pad implementation, clock tree, peripheral inventory, bootloader behavior, and firmware assumptions.
Low-power operation depends on the complete board, not only the MCU core current. Account for regulator quiescent current, sensor standby consumption, pull networks, communication activity, and leakage paths. Measure sleep-state current with peripherals in their intended states, and validate wake timing, retained state, oscillator startup, and peripheral initialization after every low-power transition.
Uyumluluk Bilgisi
Compliance status requires confirmation from the manufacturer’s current product documentation and material declaration for the exact ordering code.