SY88927VKG - 2.5Gbps Differential Receiver | Microchip
MPN: SY88927VKG ✓ نشطSY88927VKG نظرة عامة
A high-speed differential receiver is a signal-integrity device used to recover a digital data bit from a pair of complementary data lines. Differential signaling helps reject common-mode noise and reduces sensitivity to interference. The SY88927V family belongs to the broader interface IC hierarchy, where line receivers operate alongside buffers, line drivers, transceivers, clock-and-timing devices, and communication interface controllers.
The SY88927V is functionally equivalent to the EL16V devices while providing higher performance capabilities. According to the manufacturer datasheet, its output transition times are significantly faster than those of the EL16V family. This faster edge behavior is valuable when downstream logic requires concise transition intervals or when the receiver is used to retime signals inside demanding high-frequency systems.
The device supports both 3.3 V and 5 V supply operation, allowing it to interface with logic families using either voltage level. Its 2.5 Gb/s data-rate capability and greater-than-3.0 GHz operating frequency distinguish it from lower-speed differential receivers. The open-input behavior is also defined: pulling the differential input toward VEE causes the internal input clamps to force the Q output LOW.
Typical uses include high-frequency backplanes, telecommunications equipment, data-processing interfaces, test and measurement systems, and clock distribution networks. The device can also be used where a source generates high-speed differential signals but the receiving logic requires a single-ended output. Careful trace routing, controlled impedance, and stable supply references remain essential at these data rates.
For bias-rail design, the manufacturer states that the VBB pin should be used only as a bias source because its current sink and source capability is limited. Whenever VBB is used, it should be bypassed to the most positive BB supply through a 0.01 µF capacitor. This requirement helps prevent reference noise and bias instability from degrading receiver performance.
This product page combines the SY88927VKG ordering information, functional characteristics, application guidance, package details, and available family references. It also identifies the limits of the available substitution data so engineers can distinguish a verified drop-in option from a merely similar device before modifying an existing high-speed PCB.
بدائل مباشرة لـ SY88927VKG — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
لا تتوفر بدائل متوافقة تمامًا لهذا المنتج.
اطلب بدائلSY88927VKG المواصفات
| Device Type | Single differential line receiver |
| Maximum Data Rate | 2.5 Gb/s |
| Operating Frequency | Greater than 3.0 GHz |
| Supply Voltage Range | 3.3 V to 5 V |
| Logic Output | Single-ended Q output |
| Input Architecture | High-speed differential input |
| Number of Receivers | 1 receiver |
| العلبة | 8-pin MSOP, 0.118 inch (3.00 mm) width |
| نوع التركيب | Surface mount |
| Functional Reference | EL16V devices |
| Open-Input Output State | Q forced LOW when input is pulled to VEE |
| VBB Bypass Capacitor | 0.01 µF |
| VBB Current Capability | Limited current sink/source capability; use for bias only |
دليل تكوين أطراف SY88927VKG 8-pin msop, 0.118 inch (3.00 mm) width
تكوين الأطراف لـ SY88927VKG (حزمة 8-pin msop, 0.118 inch (3.00 mm) width). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ SY88927VKG.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
SY88927VKG مناسب لـ 6 التطبيقs: High-Speed Backplane Interfaces, Telecommunications Data Links, Clock Distribution Networks, Parallel-to-Serial Data Acquisition, Test and Measurement Equipment, FPGA and ASIC Signal Conditioning.
High-Speed Backplane Interfaces
The SY88927VKG is suited to backplane links that must recover a digital signal from a differential pair at rates as high as 2.5 Gb/s. Its differential input reduces common-mode disturbance, while the single-ended Q output can feed FPGA, ASIC, or logic inputs directly. The manufacturer reports operating frequencies above 3.0 GHz and output transitions faster than the EL16V family. Board implementation still requires controlled-impedance traces, symmetric routing, suitable return paths, and input termination close to the receiver.
موصى به
Telecommunications Data Links
The SY88927VKG can convert a 3.3 V or 5 V differential data link into a single-ended logic signal in telecommunications equipment. Its 2.5 Gb/s capability accommodates high-speed internal buses and data-processing paths, while the differential input improves noise immunity in systems containing switching supplies and long routing sections. System designers should preserve signal polarity, balance the input pair, and validate timing against the downstream device with realistic jitter and trace-length variation.
موصى به
Clock Distribution Networks
The SY88927VKG can recover a high-frequency differential clock and present it as a single-ended output for clock-consuming logic. Its greater-than-3.0 GHz operating-frequency capability and fast output transition times support clock distribution where edge degradation could reduce timing margin. For dependable operation, keep the differential input symmetrical, provide the specified VBB bypass arrangement when used, and confirm output amplitude, duty-cycle distortion, and jitter at the receiving endpoint.
موصى به
Parallel-to-Serial Data Acquisition
The SY88927VKG can serve as the receiving element in a parallel-to-serial conversion chain where multiple high-speed differential inputs are converted to single-ended signals for digital processing. Its 2.5 Gb/s per-channel capability and 3.3 V to 5 V operation support modern mixed-signal processing systems. Layout should minimize branch stubs, maintain continuous reference planes, and place any required termination and bias components near the MSOP pins to limit reflections and supply noise.
موصى به
Test and Measurement Equipment
The SY88927VKG is appropriate for high-speed test fixtures and instrumentation that receive differential signals from remote sensors, testers, or device-under-test boards. Its 2.5 Gb/s data rate and operating-frequency capability above 3.0 GHz make it useful for signal-path development and timing experiments. Measurement accuracy depends on controlled-impedance cables and PCB launches, stable bias, careful reference grounding, and isolation from adjacent switching circuitry.
موصى به
FPGA and ASIC Signal Conditioning
The SY88927VKG can condition a high-speed differential pair before driving a single-ended FPGA or ASIC input. The device's fast output transitions support systems where slower edges could consume timing margin, and its 3.3 V to 5 V supply range allows integration into mixed logic-voltage boards. Confirm the FPGA or ASIC input threshold, trace length, input capacitance, and termination strategy because a receiver intended for high-frequency operation still requires an accurately engineered channel.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ SY88927VKG — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | SY88927V |
|---|---|---|
| Package | 8-pin MSOP | 8-pin MSOP configuration |
| Brand | Microchip Technology | Microchip Technology |
| Device Type | Single high-speed differential receiver | Single high-speed differential receiver |
| Maximum Data Rate | 2.5 Gb/s | 2.5 Gb/s |
| Operating Frequency | Greater than 3.0 GHz | Greater than 3.0 GHz |
| Supply Voltage | 3.3 V to 5 V | 3.3 V to 5 V |
| Output Type | Single-ended Q output | Single-ended Q output |
| Functional Reference | Functionally equivalent to EL16V devices | Functionally equivalent to EL16V devices |
| VBB Bypass Requirement | 0.01 µF to most positive BB supply | 0.01 µF to most positive BB supply |
| Open-Input State | Q output forced LOW when input is pulled to VEE | Q output forced LOW when input is pulled to VEE |
أبرز الفروقات
- Higher-performance receiver than the referenced EL16V family (مقابلEL16V)
- Single-ended output from a high-speed differential input (مقابلEL16V)
- Operation across two common digital supply levels (مقابلEL16V)
- Defined behavior for an open differential input (مقابلEL16V)
ملاحظات التصميم
Route the differential input as a tightly coupled pair with continuous reference planes and avoid stubs, test pads, and unnecessary layer transitions. Match trace geometry to the PCB stack-up and maintain the designed impedance through the connector, launch, and receiver pins. At 2.5 Gb/s, reflections and pair-to-pair skew can degrade timing even when the nominal data rate is within the receiver's rating.
Follow the manufacturer's VBB guidance by using the pin only as a bias source and placing a 0.01 µF capacitor between VBB and the most positive BB supply. Place the capacitor close to the device. Keep the bias network away from switching-node copper, and provide low-impedance decoupling for the receiver's supply rails so that supply noise does not appear as receiver jitter or output timing variation.
Validate the complete channel rather than relying only on the receiver's 2.5 Gb/s rating. Include connector and package parasitics, termination placement, source-edge rate, jitter, and PCB loss in simulation or measurement. Preserve polarity and confirm the source can satisfy the receiver's input bias and termination requirements, particularly when the link is idle or the input is left open.
Do not treat the EL16V functional-equivalence statement as proof of drop-in compatibility. Verify package dimensions, numbered pin assignments, VBB behavior, supply levels, and termination for every proposed substitute. Also avoid assuming the faster output transitions of the SY88927V are interchangeable without checking downstream input thresholds, timing margins, and system-level power behavior.
معلومات الامتثال
Compliance declarations for the exact SY88927VKG configuration were not identified in the reviewed product information. Request current manufacturer documentation before using the device in a regulated or automotive design.