Microchip Technology

SY88927VKG - 2.5Gbps Differential Receiver | Microchip

N.º de pieza: SY88927VKG ✓ Activo
3.3 V to 5 V Vdss Limited current sink/source capability; use for bias only Id 8-pin MSOP, 0.118 inch (3.00 mm) width Package Greater than 3.0 GHz Speed
MOQ: 1 |

SY88927VKG Descripción general

The Microchip Technology SY88927VKG is a 2.5 Gb/s high-speed differential receiver operating from a 3.3 V to 5 V supply in an 8-pin MSOP package. The receiver is designed for high-speed digital signaling systems and supports operating frequencies exceeding 3.0 GHz. Its differential input architecture converts balanced high-speed signals into a single-ended logic output, making it suitable for backplanes, clock distribution networks, parallel-to-serial conversion systems, and other interfaces that require reliable signal conditioning at multi-gigabit data rates.

A high-speed differential receiver is a signal-integrity device used to recover a digital data bit from a pair of complementary data lines. Differential signaling helps reject common-mode noise and reduces sensitivity to interference. The SY88927V family belongs to the broader interface IC hierarchy, where line receivers operate alongside buffers, line drivers, transceivers, clock-and-timing devices, and communication interface controllers.

The SY88927V is functionally equivalent to the EL16V devices while providing higher performance capabilities. According to the manufacturer datasheet, its output transition times are significantly faster than those of the EL16V family. This faster edge behavior is valuable when downstream logic requires concise transition intervals or when the receiver is used to retime signals inside demanding high-frequency systems.

The device supports both 3.3 V and 5 V supply operation, allowing it to interface with logic families using either voltage level. Its 2.5 Gb/s data-rate capability and greater-than-3.0 GHz operating frequency distinguish it from lower-speed differential receivers. The open-input behavior is also defined: pulling the differential input toward VEE causes the internal input clamps to force the Q output LOW.

Typical uses include high-frequency backplanes, telecommunications equipment, data-processing interfaces, test and measurement systems, and clock distribution networks. The device can also be used where a source generates high-speed differential signals but the receiving logic requires a single-ended output. Careful trace routing, controlled impedance, and stable supply references remain essential at these data rates.

For bias-rail design, the manufacturer states that the VBB pin should be used only as a bias source because its current sink and source capability is limited. Whenever VBB is used, it should be bypassed to the most positive BB supply through a 0.01 µF capacitor. This requirement helps prevent reference noise and bias instability from degrading receiver performance.

This product page combines the SY88927VKG ordering information, functional characteristics, application guidance, package details, and available family references. It also identifies the limits of the available substitution data so engineers can distinguish a verified drop-in option from a merely similar device before modifying an existing high-speed PCB.

Alternativas directas para SY88927VKG — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.

No hay alternativas directas disponibles para este producto.

Solicitar alternativas

SY88927VKG Especificaciones

Device Type Single differential line receiver
Maximum Data Rate 2.5 Gb/s
Operating Frequency Greater than 3.0 GHz
Supply Voltage Range 3.3 V to 5 V
Logic Output Single-ended Q output
Input Architecture High-speed differential input
Number of Receivers 1 receiver
Encapsulado 8-pin MSOP, 0.118 inch (3.00 mm) width
Tipo de montaje Surface mount
Functional Reference EL16V devices
Open-Input Output State Q forced LOW when input is pulled to VEE
VBB Bypass Capacitor 0.01 µF
VBB Current Capability Limited current sink/source capability; use for bias only

Guía de configuración de pines de SY88927VKG 8-pin msop, 0.118 inch (3.00 mm) width

Configuración de pines para SY88927VKG (encapsulado 8-pin msop, 0.118 inch (3.00 mm) width). La numeración de pines, las funciones y los diagramas de conexión se definen en la hoja de datos del fabricante. Consúltela para conocer el footprint exacto y las directrices de soldadura.

Diagrama de patillaje del encapsulado 8-pin msop, 0.118 inch (3.00 mm) width para SY88927VKG

No hay datos detallados de patillaje disponibles para SY88927VKG.

Consulte la hoja de datos para ver la configuración completa de patillas.

Aplicaciones típicas

SY88927VKG es adecuado para 6 aplicacións: High-Speed Backplane Interfaces, Telecommunications Data Links, Clock Distribution Networks, Parallel-to-Serial Data Acquisition, Test and Measurement Equipment, FPGA and ASIC Signal Conditioning.

🖥️

High-Speed Backplane Interfaces

The SY88927VKG is suited to backplane links that must recover a digital signal from a differential pair at rates as high as 2.5 Gb/s. Its differential input reduces common-mode disturbance, while the single-ended Q output can feed FPGA, ASIC, or logic inputs directly. The manufacturer reports operating frequencies above 3.0 GHz and output transitions faster than the EL16V family. Board implementation still requires controlled-impedance traces, symmetric routing, suitable return paths, and input termination close to the receiver.

🌐

Telecommunications Data Links

The SY88927VKG can convert a 3.3 V or 5 V differential data link into a single-ended logic signal in telecommunications equipment. Its 2.5 Gb/s capability accommodates high-speed internal buses and data-processing paths, while the differential input improves noise immunity in systems containing switching supplies and long routing sections. System designers should preserve signal polarity, balance the input pair, and validate timing against the downstream device with realistic jitter and trace-length variation.

⚡

Clock Distribution Networks

The SY88927VKG can recover a high-frequency differential clock and present it as a single-ended output for clock-consuming logic. Its greater-than-3.0 GHz operating-frequency capability and fast output transition times support clock distribution where edge degradation could reduce timing margin. For dependable operation, keep the differential input symmetrical, provide the specified VBB bypass arrangement when used, and confirm output amplitude, duty-cycle distortion, and jitter at the receiving endpoint.

📺

Parallel-to-Serial Data Acquisition

The SY88927VKG can serve as the receiving element in a parallel-to-serial conversion chain where multiple high-speed differential inputs are converted to single-ended signals for digital processing. Its 2.5 Gb/s per-channel capability and 3.3 V to 5 V operation support modern mixed-signal processing systems. Layout should minimize branch stubs, maintain continuous reference planes, and place any required termination and bias components near the MSOP pins to limit reflections and supply noise.

🔧

Test and Measurement Equipment

The SY88927VKG is appropriate for high-speed test fixtures and instrumentation that receive differential signals from remote sensors, testers, or device-under-test boards. Its 2.5 Gb/s data rate and operating-frequency capability above 3.0 GHz make it useful for signal-path development and timing experiments. Measurement accuracy depends on controlled-impedance cables and PCB launches, stable bias, careful reference grounding, and isolation from adjacent switching circuitry.

🧩

FPGA and ASIC Signal Conditioning

The SY88927VKG can condition a high-speed differential pair before driving a single-ended FPGA or ASIC input. The device's fast output transitions support systems where slower edges could consume timing margin, and its 3.3 V to 5 V supply range allows integration into mixed logic-voltage boards. Confirm the FPGA or ASIC input threshold, trace length, input capacitance, and termination strategy because a receiver intended for high-frequency operation still requires an accurately engineered channel.

Resumen de productos recomendados

SY88927V Base device designation for the same receiver family Se usa en: High-Speed Backplane Interfaces, Telecommunications Data Links, Clock Distribution Networks, Parallel-to-Serial Data Acquisition, Test and Measurement Equipment, FPGA and ASIC Signal Conditioning SY88927VKG-TR Tape-and-reel ordering option for the SY88927V device Se usa en: High-Speed Backplane Interfaces, Telecommunications Data Links, Clock Distribution Networks, Parallel-to-Serial Data Acquisition, Test and Measurement Equipment, FPGA and ASIC Signal Conditioning
What is the SY88927VKG data rate and supply voltage?
The SY88927VKG supports data rates up to 2.5 Gb/s and operates from a 3.3 V to 5 V supply. According to the Microchip Technology SY88927V datasheet, the device is a single high-speed differential receiver intended for demanding digital signaling applications. Its 8-pin MSOP package also provides a compact surface-mount implementation for high-speed interface boards.
Where can I download the SY88927VKG datasheet PDF?
The official SY88927VKG datasheet is available from Microchip Technology through the SY88927V product page and the manufacturer PDF linked on this page. The document describes the 2.5 Gb/s differential receiver, 3.3 V to 5 V operation, functional relationship with EL16V devices, bias requirements, and input behavior. Use the Microchip PDF for authoritative pin, electrical, and application information.
What is the SY88927VKG pinout and package?
The SY88927VKG is packaged in an 8-pin MSOP measuring 0.118 inch, or 3.00 mm, in width. The manufacturer identifies it as a single differential receiver with a single-ended Q output. Use the pin-description table and package drawing in the official Microchip datasheet when assigning PCB nets, because the complete numbered pin assignment is not reproduced on this page.
What can replace the SY88927VKG?
The SY88927V is the direct device-family designation for the same SY88927V receiver, while the EL16V family is identified by Microchip as functionally equivalent with lower performance. A replacement should still be checked for exact package, pinout, supply voltage, input termination, and bias configuration. Use the Request a Quote form on this page when checking availability of a confirmed configuration.
Is the EL16V a drop-in replacement for the SY88927VKG?
The EL16V family is functionally equivalent to the SY88927V, but functional equivalence alone does not establish drop-in compatibility. The manufacturer states that the SY88927V offers higher performance and significantly faster output transition times. Before substituting an EL16V device, verify its exact package dimensions, pin assignments, supply rails, bias arrangement, and termination requirements against the existing PCB.
How does the SY88927VKG compare with the EL16V?
The SY88927VKG is functionally equivalent to the EL16V devices but has higher performance capabilities. Microchip specifically identifies significantly faster output transition times as an advantage. Both belong to the high-speed differential-receiver class, but the transition-time difference can matter when the receiving logic requires sharper edges or when system timing is already constrained.
When should I choose the SY88927VKG over another differential receiver?
Choose the SY88927VKG when a design needs a 2.5 Gb/s single differential receiver operating from 3.3 V or 5 V in an 8-pin MSOP. It is particularly appropriate when the source and receiving logic require a single-ended output and the interface operates above 3.0 GHz. Confirm package pinout, VBB biasing, and signal termination before making the selection.
Is the SY88927VKG suitable for a 3.3 V interface?
Yes, the SY88927VKG supports both 3.3 V and 5 V operation. The manufacturer lists the device as a 3.3 V to 5 V high-speed differential receiver capable of 2.5 Gb/s signaling. The selected supply level must be coordinated with the Q-output voltage levels, input bias network, and downstream logic so that no receiver output exceeds the connected device's input limits.
Where can I buy the SY88927VKG and check its lead time?
Use the Request a Quote form on this page to request the SY88927VKG, current availability, and lead time for the required package and quantity. Commercial terms can change with quantity, market conditions, and configuration, so the form is the appropriate route for a current purchasing response. The product is offered as an 8-pin MSOP receiver.
What is the current price of the SY88927VKG?
Use the Request a Quote form on this page for a current SY88927VKG price and quantity schedule. The platform calculates customer pricing rather than embedding a static quote in technical content. Include the required quantity, tube or other delivery preference, and target shipment location so the commercial response can reflect the actual order configuration.
Is the SY88927VKG in stock?
Current stock should be confirmed through the Request a Quote form on this page because inventory can change independently of the technical specifications. The SY88927VKG is an active, surface-mount 8-pin MSOP receiver from Microchip Technology. A quotation response can confirm current supply, manufacturing lead time, and available shipment quantity for the requested order.
How should the VBB pin be bypassed on the SY88927VKG?
The manufacturer requires VBB to be bypassed to the most positive BB supply through a 0.01 µF capacitor whenever VBB is used. According to the Microchip datasheet, VBB has limited current sink and source capability and should be used only as a bias source. Keeping the bypass capacitor close to the device helps maintain a stable bias reference for the high-speed receiver.
What happens when the SY88927VKG differential input is open?
When the input is open and pulled to VEE, the SY88927VKG internal input clamps force the Q output LOW. The manufacturer describes this behavior explicitly in the SY88927V datasheet. It provides a defined fail-safe output condition for an open input, although the system should still include intentional bias or termination when a stable high output is required.
What are the key specifications engineers should know about the SY88927VKG?
The principal specifications are a 2.5 Gb/s maximum data rate, operation above 3.0 GHz, a 3.3 V to 5 V supply range, one differential receiver, and an 8-pin MSOP package. According to Microchip, the SY88927V is functionally equivalent to EL16V devices while providing faster output transitions. These parameters define its suitability for high-speed single-ended-output interfaces.
Is the SY88927VKG compliant with RoHS and automotive qualification?
The RoHS, REACH, and automotive qualification status of the exact SY88927VKG configuration has not been established in the product documentation reviewed for this page. Request the current manufacturer declaration or qualification record for the exact ordering code before using the device in a regulated or automotive design. The listed application role is a general-purpose high-speed differential receiver.

Datos de referencia de ingeniería para SY88927VKG — comparación, orientación de diseño e información de cumplimiento.

Guía de selección

Choose the SY88927VKG when a system requires a single-ended output from a high-speed differential signal at rates up to 2.5 Gb/s, particularly when operating above 3.0 GHz or using a 3.3 V or 5 V logic environment. It is preferable to the EL16V family where the faster output transitions of the SY88927V improve timing margin or simplify integration with downstream logic. For an existing 8-pin MSOP design, the SY88927V family ordering information is the relevant starting point, but every substitution must be checked against the numbered pinout, supply arrangement, and VBB requirements. The manufacturer does not provide enough pin-level package information for the EL16V family to classify it as a verified drop-in replacement. When the receiver is used in a backplane, test system, or FPGA interface, prioritize controlled-impedance routing, termination, and a stable bias network over differences in headline data rate.

Comparación con alternativas

Parámetro Este producto SY88927V
Package 8-pin MSOP 8-pin MSOP configuration
Brand Microchip Technology Microchip Technology
Device Type Single high-speed differential receiver Single high-speed differential receiver
Maximum Data Rate 2.5 Gb/s 2.5 Gb/s
Operating Frequency Greater than 3.0 GHz Greater than 3.0 GHz
Supply Voltage 3.3 V to 5 V 3.3 V to 5 V
Output Type Single-ended Q output Single-ended Q output
Functional Reference Functionally equivalent to EL16V devices Functionally equivalent to EL16V devices
VBB Bypass Requirement 0.01 µF to most positive BB supply 0.01 µF to most positive BB supply
Open-Input State Q output forced LOW when input is pulled to VEE Q output forced LOW when input is pulled to VEE

Diferenciadores clave

  • Higher-performance receiver than the referenced EL16V family (frente a EL16V)
  • Single-ended output from a high-speed differential input (frente a EL16V)
  • Operation across two common digital supply levels (frente a EL16V)
  • Defined behavior for an open differential input (frente a EL16V)

Notas de diseño

Route the differential input as a tightly coupled pair with continuous reference planes and avoid stubs, test pads, and unnecessary layer transitions. Match trace geometry to the PCB stack-up and maintain the designed impedance through the connector, launch, and receiver pins. At 2.5 Gb/s, reflections and pair-to-pair skew can degrade timing even when the nominal data rate is within the receiver's rating.

Follow the manufacturer's VBB guidance by using the pin only as a bias source and placing a 0.01 µF capacitor between VBB and the most positive BB supply. Place the capacitor close to the device. Keep the bias network away from switching-node copper, and provide low-impedance decoupling for the receiver's supply rails so that supply noise does not appear as receiver jitter or output timing variation.

Validate the complete channel rather than relying only on the receiver's 2.5 Gb/s rating. Include connector and package parasitics, termination placement, source-edge rate, jitter, and PCB loss in simulation or measurement. Preserve polarity and confirm the source can satisfy the receiver's input bias and termination requirements, particularly when the link is idle or the input is left open.

Do not treat the EL16V functional-equivalence statement as proof of drop-in compatibility. Verify package dimensions, numbered pin assignments, VBB behavior, supply levels, and termination for every proposed substitute. Also avoid assuming the faster output transitions of the SY88927V are interchangeable without checking downstream input thresholds, timing margins, and system-level power behavior.

Información de cumplimiento

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Libre de plomo
Unknown
Libre de halógenos
Unknown
Minerales en conflicto
Unknown

Compliance declarations for the exact SY88927VKG configuration were not identified in the reviewed product information. Request current manufacturer documentation before using the device in a regulated or automotive design.

Datos verificados el: 2026-11-16 — datos verificados y seleccionados por el equipo de ingeniería de componentes de XAIPART

Búsquedas relacionadas

SY88927VKG datasheet SY88927VKG pinout SY88927VKG datasheet pdf SY88927VKG equivalent SY88927VKG replacement SY88927VKG price SY88927VKG stock Microchip SY88927VKG SY88927VKG 2.5Gbps receiver SY88927VKG 8-MSOP SY88927VKG application circuit SY88927VKG vs EL16V

Componentes & términos relacionados

Microchip Technology SY88927VKG SY88927V SY88927VKG-TR EL16V high-speed differential receiver line receiver interface IC semiconductor single-ended output differential signaling common-mode rejection 2.5 Gb/s 3.3 V to 5 V supply VBB bias 0.01 µF bypass capacitor 8-pin MSOP surface-mount package backplane interface clock distribution FPGA interface signal integrity controlled impedance open-input clamp
RFQ de presupuesto rápido
Complete los detalles — nuestro equipo de ventas responderá en un plazo de 24 horas
Número de pieza Fabricante Encapsulado QTY Precio objetivo Total
✓
¡Presupuesto enviado!

Responderemos a su correo electrónico en un plazo de 24 horas

1
RFQ enviado
2
Presupuesto recibido
3
Pedido realizado
4
Pago
5
Enviado
6
Entregado
Ver detalles del RFQ