THS4120ID - 100MHz Fully Differential Amplifier | Texas Instruments
MPN: THS4120ID ✓ نشطTHS4120ID نظرة عامة
A fully differential amplifier is a signal-conditioning amplifier whose two inputs and two outputs remain balanced throughout the signal path. This architecture helps suppress common-mode noise, reduces even-order distortion, and provides a convenient interface for analog-to-digital converters, video systems, communications equipment, and instrumentation. The THS4120 combines this balanced operation with CMOS integration and single-supply operation at 3.3 V.
The 100 MHz bandwidth supports high-frequency signal amplification without moving the operating point far into the roll-off region. A 43 V/us slew rate gives adequate headroom for large-amplitude, fast-edge signals, while the fully differential topology preserves signal integrity in systems where cable pickup, ground differences, and shared supply disturbances are important concerns. The shutdown function can reduce power consumption when the signal path is not required.
The manufacturer describes the THS4120 as a 3.3 V, 100 MHz, 43 V/us fully differential CMOS amplifier. Published feature data also identifies a 64 dB common-mode rejection ratio, a 5.4 nV/Hz input-referred noise density at 10 kHz, and -75 dB total harmonic distortion at 1 MHz with a 2 VPP output. These characteristics place it between general-purpose op amps and specialized high-speed fully differential devices.
Typical applications include ADC driver circuits, video signal conditioning, balanced communications paths, active filters, test and measurement equipment, and instrumentation requiring low-noise differential amplification. The device is particularly useful when the source and destination both support differential signaling, because balanced operation can reduce susceptibility to common-mode interference.
Layout is critical because operating at 100 MHz requires short connections, controlled return paths, and careful separation between the differential signal nodes and high-impedance gain-setting components. Use the manufacturer pin-description and reference-circuit information when assigning PCB nets and selecting external resistors or capacitors.
This product page combines the manufacturer specifications, verified ordering information, application guidance, comparison parameters, and practical design notes to support faster component selection and more reliable high-speed PCB implementation.
بدائل مباشرة لـ THS4120ID — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع THS4120ID (نفس عامل الشكل والبصمة) — يختلف في Package.
THS4120CDRG4
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
THS4120CDGNG4
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
THS4120CD
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←THS4120ID الحدود القصوى والخصائص الكهربائية
| Device Type | Fully differential CMOS amplifier |
| Number of Circuits | 1 circuit |
| جهد التغذية | 3.3 V |
| -3 dB Bandwidth | 100 MHz |
| Slew Rate | 43 V/us |
| Input Noise Density | 5.4 nV/Hz at 10 kHz |
| Total Harmonic Distortion | -75 dB at 1 MHz, 2 VPP output |
| Common-Mode Rejection Ratio | 64 dB |
| Input Architecture | Differential input |
| Output Architecture | Balanced differential output |
| Shutdown | Yes |
| نطاق درجة حرارة التشغيل | -40 C to 85 C |
| العلبة | 8-pin SOIC (D) |
| نوع التركيب | Surface mount |
دليل تكوين أطراف THS4120ID 8-pin soic (d)
تكوين الأطراف لـ THS4120ID (حزمة 8-pin soic (d)). يتميز هذا المكوّن التناظري بأطراف الإدخال والإخراج وإمداد الطاقة. راجع ورقة بيانات الشركة المصنعة لتكوينات طرف إلغاء الإزاحة والتعويض والتمكين. مثالي لدوائر تكييف الإشارة والمضخمات.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ THS4120ID.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
THS4120ID مناسب لـ 6 التطبيقs: High-Speed ADC Signal Conditioning, Balanced Video Amplification, Communications Receive Chain, Precision Active Filtering, Test and Measurement Instrumentation, Industrial Sensor Signal Conditioning.
High-Speed ADC Signal Conditioning
The THS4120ID fits differential ADC front ends that require balanced drive and rejection of common-mode disturbance. Its 100 MHz -3 dB bandwidth provides useful frequency range for high-speed converters, while the 43 V/us slew rate supports rapid output transitions. The 64 dB common-mode rejection ratio can reduce errors caused by source imbalance or shared-ground interference. In a typical circuit, the amplifier drives the ADC from a balanced source and uses matched feedback networks to establish differential gain. Confirm the ADC's required input range, settling behavior, and clock edge relationship against the manufacturer limits before finalizing the design.
موصى به
Balanced Video Amplification
The THS4120ID is suitable for differential video paths where balanced signaling helps maintain signal integrity. Its 100 MHz bandwidth covers common high-definition video formats, and the fully differential architecture provides equal signal treatment across the two outputs. The 43 V/us slew rate offers useful margin for fast transitions without requiring a general-purpose amplifier architecture. When implementing the stage, use matched source and feedback impedances and keep both signal branches geometrically similar. Verify the required output amplitude, allowed common-mode range, and video timing requirements before using the device as a direct or reconstructed-video driver.
موصى به
Communications Receive Chain
The THS4120ID can amplify balanced communications signals when the receiver requires a true differential input and balanced output. Its 5.4 nV/Hz input-referred noise at 10 kHz and 64 dB CMRR are useful for maintaining signal integrity in systems exposed to common-mode noise. The 100 MHz bandwidth supports baseband, IF, and other high-speed balanced stages. Place the device close to the source or receiver interface, terminate both branches consistently, and account for the shutdown state during system power sequencing. Confirm gain-bandwidth stability, output swing, and the exact common-mode range for the intended communication standard.
موصى به
Precision Active Filtering
The THS4120ID can serve as the gain element in high-frequency active filters because it combines a 100 MHz bandwidth with fully differential operation. Differential filtering reduces sensitivity to component mismatch and common-mode disturbances when both halves of the circuit are implemented symmetrically. Its 43 V/us slew rate helps preserve low distortion for larger filter signals. Use precision resistors and capacitors, inspect the resulting gain-bandwidth and stability behavior, and keep the feedback paths short. The published -75 dB THD at 1 MHz with a 2 VPP output provides a useful reference, but actual distortion depends on frequency, gain, load, and supply configuration.
موصى به
Test and Measurement Instrumentation
The THS4120ID is appropriate for instrumentation front ends that measure or generate balanced signals over a broad frequency range. Its 100 MHz bandwidth supports fast transient and frequency-domain measurements, while differential input and output simplify interface balancing with test equipment. The 5.4 nV/Hz input noise and 64 dB CMRR can improve measurement integrity when common-mode pickup is present. For best results, use low-noise gain-setting resistors, controlled impedance paths, and an output termination matched to the instrument. The shutdown function allows the amplifier to be disabled between measurement bursts when system timing permits.
موصى به
Industrial Sensor Signal Conditioning
The THS4120ID can condition balanced outputs from high-speed industrial sensors when the sensor and acquisition system support differential signaling. Its 100 MHz bandwidth handles rapidly varying sensor signals, and its common-mode rejection of 64 dB helps suppress interference coupled equally into both input lines. The balanced output can connect directly to a downstream converter when the voltage range and impedance are compatible. Keep sensor wiring short and shielded where practical, maintain symmetric input routing, and use the shutdown input during idle periods if the acquisition architecture permits. Validate gain, bandwidth, noise, and input-range requirements at the sensor's worst-case operating limits.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ THS4120ID — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | THS4120CDRG4 | THS4120CDGNG4 | THS4120CD |
|---|---|---|---|---|
| Package | 8-pin SOIC (D) | 8-pin SOIC - same | 8-pin SOIC - same | 8-pin SOIC - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Device Type | Fully differential CMOS amplifier | Fully differential amplifier | THS412x fully differential amplifier | THS412x fully differential amplifier |
أبرز الفروقات
- Defined 43 V/us slew rate for the target order code (مقابلTHS4120CDRG4)
- Tube-format ordering configuration (مقابلTHS4120CDRG4)
- Specific 100 MHz bandwidth and 64 dB CMRR combination (مقابلTHS4120CD)
ملاحظات التصميم
Route the input, feedback, and output paths as short differential pairs with nearly identical geometry. A continuous ground reference should run beneath each pair where the board stack-up permits. High-speed signals couple readily to adjacent traces, so keep the shutdown and gain-setting networks away from the sensitive input nodes. Ground and supply-return currents from external circuits should not share narrow segments with the amplifier return path.
Use matched components and matched trace lengths for both halves of the fully differential signal path. Small resistance or capacitance mismatches can create common-to-differential conversion and degrade the available 64 dB CMRR. Terminate or load both outputs consistently, and confirm the gain, stability, and output-swing limits against the manufacturer application information rather than treating the circuit as a conventional single-ended op amp.
Keep the 3.3 V supply connection short and provide local high-frequency bypassing close to the device. Place the bypass capacitor where the power and ground connections form a compact loop rather than routing the capacitor through a long trace. Verify the device's maximum supply and input/output voltage limits in the manufacturer datasheet, especially when the downstream stage can approach the positive rail.
Do not infer identical behavior from a shared family name or order-code suffix. The THS4120IDR is a tape-and-reel ordering option, while other THS412x order codes may use different gain configurations or performance ratings. Confirm the exact pinout, gain setting, supply range, temperature grade, and shutdown polarity in the manufacturer ordering table before replacing a component on an assembled board.
معلومات الامتثال
The verified manufacturer and distributor information does not explicitly state the requested compliance attributes. THS4120ID is listed with a -40 C to 85 C operating-temperature range, but that rating is not evidence of AEC-Q100 qualification.