Texas Instruments

THS4120ID - 100MHz Fully Differential Amplifier | Texas Instruments

MPN: THS4120ID ✓ 啟用中
3.3 V Vdss 8-pin SOIC (D) Package
MOQ: 1 |

THS4120ID 概覽

Texas Instruments THS4120ID is a 3.3 V, 100 MHz, 43 V/us fully differential CMOS amplifier with shutdown in an 8-pin SOIC package. It accepts a differential input and drives a differential output, providing a true balanced signal path for high-speed analog systems. Its key characteristics include a 100 MHz bandwidth, 43 V/us slew rate, 64 dB common-mode rejection, 5.4 nV/Hz input-referred noise, and shutdown capability.

A fully differential amplifier is a signal-conditioning amplifier whose two inputs and two outputs remain balanced throughout the signal path. This architecture helps suppress common-mode noise, reduces even-order distortion, and provides a convenient interface for analog-to-digital converters, video systems, communications equipment, and instrumentation. The THS4120 combines this balanced operation with CMOS integration and single-supply operation at 3.3 V.

The 100 MHz bandwidth supports high-frequency signal amplification without moving the operating point far into the roll-off region. A 43 V/us slew rate gives adequate headroom for large-amplitude, fast-edge signals, while the fully differential topology preserves signal integrity in systems where cable pickup, ground differences, and shared supply disturbances are important concerns. The shutdown function can reduce power consumption when the signal path is not required.

The manufacturer describes the THS4120 as a 3.3 V, 100 MHz, 43 V/us fully differential CMOS amplifier. Published feature data also identifies a 64 dB common-mode rejection ratio, a 5.4 nV/Hz input-referred noise density at 10 kHz, and -75 dB total harmonic distortion at 1 MHz with a 2 VPP output. These characteristics place it between general-purpose op amps and specialized high-speed fully differential devices.

Typical applications include ADC driver circuits, video signal conditioning, balanced communications paths, active filters, test and measurement equipment, and instrumentation requiring low-noise differential amplification. The device is particularly useful when the source and destination both support differential signaling, because balanced operation can reduce susceptibility to common-mode interference.

Layout is critical because operating at 100 MHz requires short connections, controlled return paths, and careful separation between the differential signal nodes and high-impedance gain-setting components. Use the manufacturer pin-description and reference-circuit information when assigning PCB nets and selecting external resistors or capacitors.

This product page combines the manufacturer specifications, verified ordering information, application guidance, comparison parameters, and practical design notes to support faster component selection and more reliable high-speed PCB implementation.

直接替換替代品,適用於 THS4120ID — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。

此系列的變體

與下列產品可直接替換的同系列型號: THS4120ID (相同外形與佔位) — 差異在於 Package.

Texas Instruments
Package: 8-SOIC
比較對象 THS4120ID →
Texas Instruments
Package: 8-pin SOIC
比較對象 THS4120ID →

THS4120CDRG4

✅ 直接替換
📦 8-pin SOIC (D)
Listed slew rate is 55 V/us versus 43 V/us, approximately 28% higher; cross-reference identifies matching terminals and package

📋 參考替代品(不在目錄中)

THS4120CDGNG4

✅ 直接替換
📦 8-pin SOIC (D)
Same THS412x fully differential amplifier family; complete electrical difference for this order code is not quantified in the available comparison data

📋 參考替代品(不在目錄中)

THS4120CD

✅ 直接替換
Texas Instruments
📦 8-pin SOIC (D)
Fully differential CMOS amplifier · 1 circuit · 3.3 V · 100 MHz · 43 V/us · Fully differential · Differential · Yes

聯絡詢價

查看資料表 →

THS4120ID 最大額定值與電氣特性

Device Type Fully differential CMOS amplifier
Number of Circuits 1 circuit
供應電壓 3.3 V
-3 dB Bandwidth 100 MHz
Slew Rate 43 V/us
Input Noise Density 5.4 nV/Hz at 10 kHz
Total Harmonic Distortion -75 dB at 1 MHz, 2 VPP output
Common-Mode Rejection Ratio 64 dB
Input Architecture Differential input
Output Architecture Balanced differential output
Shutdown Yes
工作溫度範圍 -40 C to 85 C
封裝 8-pin SOIC (D)
安裝類型 Surface mount

THS4120ID 8-pin soic (d) 腳位配置指南

THS4120ID(8-pin soic (d) 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。

THS4120ID 的 8-pin soic (d) 封裝腳位圖

無詳細腳位定義資料: THS4120ID.

請參閱 資料表 以查看完整腳位配置。

典型應用

THS4120ID 適用於 6 應用s: High-Speed ADC Signal Conditioning, Balanced Video Amplification, Communications Receive Chain, Precision Active Filtering, Test and Measurement Instrumentation, Industrial Sensor Signal Conditioning.

🔧

High-Speed ADC Signal Conditioning

The THS4120ID fits differential ADC front ends that require balanced drive and rejection of common-mode disturbance. Its 100 MHz -3 dB bandwidth provides useful frequency range for high-speed converters, while the 43 V/us slew rate supports rapid output transitions. The 64 dB common-mode rejection ratio can reduce errors caused by source imbalance or shared-ground interference. In a typical circuit, the amplifier drives the ADC from a balanced source and uses matched feedback networks to establish differential gain. Confirm the ADC's required input range, settling behavior, and clock edge relationship against the manufacturer limits before finalizing the design.

📺

Balanced Video Amplification

The THS4120ID is suitable for differential video paths where balanced signaling helps maintain signal integrity. Its 100 MHz bandwidth covers common high-definition video formats, and the fully differential architecture provides equal signal treatment across the two outputs. The 43 V/us slew rate offers useful margin for fast transitions without requiring a general-purpose amplifier architecture. When implementing the stage, use matched source and feedback impedances and keep both signal branches geometrically similar. Verify the required output amplitude, allowed common-mode range, and video timing requirements before using the device as a direct or reconstructed-video driver.

🌐

Communications Receive Chain

The THS4120ID can amplify balanced communications signals when the receiver requires a true differential input and balanced output. Its 5.4 nV/Hz input-referred noise at 10 kHz and 64 dB CMRR are useful for maintaining signal integrity in systems exposed to common-mode noise. The 100 MHz bandwidth supports baseband, IF, and other high-speed balanced stages. Place the device close to the source or receiver interface, terminate both branches consistently, and account for the shutdown state during system power sequencing. Confirm gain-bandwidth stability, output swing, and the exact common-mode range for the intended communication standard.

📡

Precision Active Filtering

The THS4120ID can serve as the gain element in high-frequency active filters because it combines a 100 MHz bandwidth with fully differential operation. Differential filtering reduces sensitivity to component mismatch and common-mode disturbances when both halves of the circuit are implemented symmetrically. Its 43 V/us slew rate helps preserve low distortion for larger filter signals. Use precision resistors and capacitors, inspect the resulting gain-bandwidth and stability behavior, and keep the feedback paths short. The published -75 dB THD at 1 MHz with a 2 VPP output provides a useful reference, but actual distortion depends on frequency, gain, load, and supply configuration.

🖥️

Test and Measurement Instrumentation

The THS4120ID is appropriate for instrumentation front ends that measure or generate balanced signals over a broad frequency range. Its 100 MHz bandwidth supports fast transient and frequency-domain measurements, while differential input and output simplify interface balancing with test equipment. The 5.4 nV/Hz input noise and 64 dB CMRR can improve measurement integrity when common-mode pickup is present. For best results, use low-noise gain-setting resistors, controlled impedance paths, and an output termination matched to the instrument. The shutdown function allows the amplifier to be disabled between measurement bursts when system timing permits.

🏭

Industrial Sensor Signal Conditioning

The THS4120ID can condition balanced outputs from high-speed industrial sensors when the sensor and acquisition system support differential signaling. Its 100 MHz bandwidth handles rapidly varying sensor signals, and its common-mode rejection of 64 dB helps suppress interference coupled equally into both input lines. The balanced output can connect directly to a downstream converter when the voltage range and impedance are compatible. Keep sensor wiring short and shielded where practical, maintain symmetric input routing, and use the shutdown input during idle periods if the acquisition architecture permits. Validate gain, bandwidth, noise, and input-range requirements at the sensor's worst-case operating limits.

What are the key specifications of THS4120ID that engineers should know?
The THS4120ID is a 3.3 V, 100 MHz, 43 V/us fully differential CMOS amplifier with shutdown in an 8-pin SOIC package. According to the Texas Instruments product page and manufacturer datasheet, it also provides 64 dB CMRR, 5.4 nV/Hz input-referred noise at 10 kHz, and -75 dB THD at 1 MHz with a 2 VPP output. Its differential input and balanced output make it suitable for ADC drivers, video paths, filters, and instrumentation.
What is the operating voltage of THS4120ID?
The THS4120ID operates from a 3.3 V supply. According to the Texas Instruments product page and manufacturer datasheet, this is a single-supply, fully differential CMOS amplifier designed for high-speed analog signal conditioning. Designers should keep the supply and signal amplitudes within the limits listed in the manufacturer datasheet, particularly when operating close to the positive supply rail.
What is the bandwidth and slew rate of THS4120ID?
The THS4120ID provides a 100 MHz -3 dB bandwidth and a 43 V/us slew rate. According to the Texas Instruments product page and manufacturer datasheet, these speed characteristics position it as a high-speed fully differential amplifier. Bandwidth determines how closely the circuit can reproduce high-frequency content, while slew rate governs the ability to produce large output-voltage changes quickly.
Where can I download the THS4120ID datasheet PDF?
The official THS4120 product page is the appropriate starting point for the THS4120ID datasheet, pin descriptions, ordering information, and application guidance. According to Texas Instruments, the THS4120 is a 3.3 V, 100 MHz, 43 V/us fully differential CMOS amplifier with shutdown. Use the manufacturer datasheet PDF linked from that page when finalizing pin assignments and circuit values.
Where can I find the THS4120ID pinout?
Use the pin-description table in the Texas Instruments THS4120 manufacturer datasheet for the authoritative THS4120ID pinout. The verified ordering information identifies the THS4120ID as an 8-pin SOIC with differential input and differential output. The package drawing and pin table should be checked together before routing the board, especially for shutdown, feedback, and power connections.
What can replace the THS4120ID on the same 8-pin SOIC footprint?
THS4120IDR and THS4120CDRG4 are documented alternatives associated with the THS4120 family, but each requires careful review of ordering code, reel configuration, and electrical differences. THS4120IDR changes the shipping format rather than adding a functional difference, while the THS4120CDRG4 comparison lists a 55 V/us slew rate versus 43 V/us for the target. Confirm the complete pinout and gain configuration in the manufacturer datasheet before substitution.
Is THS4120ID suitable for high-speed ADC driver applications?
Yes, the THS4120ID is suitable for many high-speed ADC driver applications because it combines a differential input, balanced output, 100 MHz bandwidth, and 43 V/us slew rate. According to the Texas Instruments manufacturer datasheet, its common-mode rejection ratio is 64 dB and its input-referred noise is 5.4 nV/Hz at 10 kHz. ADC compatibility still depends on input range, settling time, and output-voltage limits.
Is THS4120ID suitable for video signal conditioning?
The THS4120ID can be used for balanced video signal conditioning when the system uses differential signaling and operates within the amplifier's stated limits. Its 100 MHz bandwidth, 43 V/us slew rate, and 64 dB CMRR help preserve signal integrity and reject common-mode disturbance. According to the Texas Instruments product page, the device is a fully differential CMOS amplifier with shutdown for low-power system states.
What is the difference between THS4120ID and THS4120IDR?
The principal documented difference between THS4120ID and THS4120IDR is the shipping format: THS4120ID is associated with an 8-pin SOIC tube, while THS4120IDR is the tape-and-reel ordering option. Both identify the same THS4120 family device. Use the manufacturer ordering table to confirm device grade, temperature range, package, and reel orientation rather than assuming interchangeability solely from the suffix.
THS4120ID vs THS4120CDRG4 - which is better for a fast ADC driver?
THS4120CDRG4 offers a listed 55 V/us slew rate, which is approximately 28 percent higher than the THS4120ID's 43 V/us specification, while comparison information identifies the same 8-pin functional family and terminal arrangement. According to the available cross-reference data, the devices are replacement-compatible. Final selection should confirm gain settings, supply limits, output swing, and the exact orderable pin configuration.
When should I choose THS4120ID over a THS4120 family alternative?
Choose THS4120ID when the design requires the specified 43 V/us slew rate, 100 MHz bandwidth, tube-format procurement, and the exact ordering configuration associated with the target. A family alternative may offer a different slew rate or shipping format. According to the Texas Instruments ordering information, the target is an 8-pin SOIC device rated for -40 C to 85 C, so those constraints should remain unchanged.
Is THS4120ID the same as THS4120CDGNG4?
THS4120ID and THS4120CDGNG4 belong to the same THS412x fully differential amplifier family, but they are not automatically identical in every ordering or electrical detail. The comparison data identifies both parts but does not provide a complete parameter table for the CDGNG4 order code. Check the manufacturer datasheet for gain configuration, package, reel orientation, and shutdown behavior before treating them as exact equivalents.
How should I design the PCB for the THS4120ID?
Keep the 100 MHz signal path compact, use short differential traces, and provide a continuous return path beneath the pair. Place feedback and gain-setting components close to their associated amplifier pins, and avoid routing sensitive input nodes beside supply, shutdown, or digital return currents. According to the Texas Instruments manufacturer datasheet, fully differential operation requires deliberate balancing of both signal paths and their feedback networks.
How much power does the THS4120ID consume?
The THS4120ID supply current and shutdown current are not stated in the verified manufacturer information available for this page. Its shutdown function can reduce consumption when the amplifier is inactive, but the exact savings depend on the control state and operating conditions. Consult the Texas Instruments manufacturer datasheet current-consumption table and complete the thermal calculation with the actual supply voltage and load.
Where can I buy THS4120ID and check its current lead time?
Use the Request a Quote form on this page to request the current THS4120ID price, stock position, minimum order quantity, and lead time. The verified listing identifies THS4120ID as an 8-SOIC Texas Instruments differential amplifier and the manufacturer lists the THS4120 product family for ordering. Current commercial availability should be confirmed through the quote process because distribution status can change.
Is THS4120ID currently in stock?
Current THS4120ID inventory should be confirmed through the Request a Quote form on this page. The verified product listings identify the device as orderable, but inventory quantities can vary by package, tube quantity, and distribution channel. The manufacturer ordering page also lists the THS4120ID configuration, providing a stable reference for the requested part number.
What is the price of THS4120ID?
Use the Request a Quote form on this page for the current THS4120ID price and quantity breaks. According to the Texas Instruments ordering information, the target is an 8-pin SOIC device with a -40 C to 85 C operating range. A firm commercial quote should reflect the requested quantity, tube packaging, current inventory, and applicable supply conditions.
What is the lead time for THS4120ID?
The current THS4120ID lead time should be requested through the Request a Quote form on this page. Lead time can vary with order quantity, manufacturing status, and packaging configuration. The verified manufacturer information confirms the THS4120ID order code and its 8-pin SOIC configuration, while the quote response should provide the most actionable availability information.

工程參考資料,適用於 THS4120ID — 比較、設計指引及合規資訊。

選型指南

Choose the THS4120ID when the circuit specifically requires a 3.3 V, 100 MHz fully differential amplifier with a 43 V/us slew rate, shutdown capability, and the associated 8-pin SOIC configuration. It is well suited to balanced ADC interfaces, video paths, filters, and instrumentation where common-mode rejection and a true differential signal path are important. Consider THS4120CDRG4 when its listed 55 V/us slew rate is useful and its exact gain and shutdown configuration matches the intended circuit; the target provides the lower, explicitly specified slew rate. THS4120CDGNG4 and THS4120CD belong to the same broader THS412x family, but their complete order-code parameters should be checked before use. THS4120IDR should not be selected merely for interchangeability because its principal distinction is reel packaging. For every option, verify the complete pinout, supply rating, output swing, stability configuration, and temperature range.

與替代品比較

參數 本產品 THS4120CDRG4 THS4120CDGNG4 THS4120CD
Package 8-pin SOIC (D) 8-pin SOIC - same 8-pin SOIC - same 8-pin SOIC - same
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Device Type Fully differential CMOS amplifier Fully differential amplifier THS412x fully differential amplifier THS412x fully differential amplifier

主要差異化特點

  • Defined 43 V/us slew rate for the target order code (對比THS4120CDRG4)
  • Tube-format ordering configuration (對比THS4120CDRG4)
  • Specific 100 MHz bandwidth and 64 dB CMRR combination (對比THS4120CD)

設計說明

Route the input, feedback, and output paths as short differential pairs with nearly identical geometry. A continuous ground reference should run beneath each pair where the board stack-up permits. High-speed signals couple readily to adjacent traces, so keep the shutdown and gain-setting networks away from the sensitive input nodes. Ground and supply-return currents from external circuits should not share narrow segments with the amplifier return path.

Use matched components and matched trace lengths for both halves of the fully differential signal path. Small resistance or capacitance mismatches can create common-to-differential conversion and degrade the available 64 dB CMRR. Terminate or load both outputs consistently, and confirm the gain, stability, and output-swing limits against the manufacturer application information rather than treating the circuit as a conventional single-ended op amp.

Keep the 3.3 V supply connection short and provide local high-frequency bypassing close to the device. Place the bypass capacitor where the power and ground connections form a compact loop rather than routing the capacitor through a long trace. Verify the device's maximum supply and input/output voltage limits in the manufacturer datasheet, especially when the downstream stage can approach the positive rail.

Do not infer identical behavior from a shared family name or order-code suffix. The THS4120IDR is a tape-and-reel ordering option, while other THS412x order codes may use different gain configurations or performance ratings. Confirm the exact pinout, gain setting, supply range, temperature grade, and shutdown polarity in the manufacturer ordering table before replacing a component on an assembled board.

合規資訊

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
無鉛
Unknown
無鹵
Unknown
衝突礦產
Unknown

The verified manufacturer and distributor information does not explicitly state the requested compliance attributes. THS4120ID is listed with a -40 C to 85 C operating-temperature range, but that rating is not evidence of AEC-Q100 qualification.

資料驗證日期: 2026-11-10 — 資料由 XAIPART 元件工程團隊驗證及整理

相關搜尋

THS4120ID datasheet THS4120ID datasheet pdf THS4120ID pinout THS4120ID equivalent THS4120ID replacement THS4120ID cross reference THS4120ID vs THS4120CDRG4 THS4120ID footprint THS4120ID 100 MHz amplifier THS4120ID 43 V/us THS4120ID price THS4120ID stock Texas Instruments THS4120ID THS4120 application circuit

相關元件與詞彙

Texas Instruments THS4120ID THS4120IDR THS4120CDRG4 THS4120CDGNG4 THS4120CD fully differential amplifier differential amplifier operational amplifier amplifier IC CMOS common-mode rejection ratio CMRR input-referred noise slew rate balanced output shutdown 8-pin SOIC SOIC package surface-mount package ADC driver video signal conditioning active filter semiconductor
快速報價 RFQ
請填寫完整詳細資料 — 我們的業務團隊將於 24 小時內回覆
料號 製造商 封裝 QTY 目標價格 小計
✓
報價已提交!

我們將於 24 小時內回覆您的電子郵件

1
詢價已提交
2
已收到報價
3
已下單
4
付款
5
已出貨
6
已送達
檢視詢價單詳情