Texas Instruments

TLV2432CD - Dual 10V 500kHz Rail-to-Rail Op Amp | TI

MPN: TLV2432CD ✓ نشط
10 V Vdss 8-SOIC, 3.90 mm width Package
الحد الأدنى للطلب: 1 |

TLV2432CD نظرة عامة

The Texas Instruments TLV2432CD is a dual, 10 V, 500 kHz CMOS operational amplifier with rail-to-rail output capability, supplied in an 8-pin SOIC package. It combines two amplifier channels, a 10 V maximum supply rating, and a 500 kHz gain-bandwidth product in one compact surface-mount IC.

An operational amplifier is an analog building block used to amplify voltage differences, buffer signals, integrate errors, and drive control inputs. The TLV2432 belongs to the CMOS operational-amplifier hierarchy and is designed for low-voltage signal conditioning where two channels, rail-to-rail output swing, and low supply current can simplify a board design.

The device is identified as a CMOS, dual-amplifier circuit with rail-to-rail output operation. Its 500 kHz bandwidth is suitable for low-to-moderate-frequency instrumentation, while the 10 V supply rating positions it for circuits operating below the 10 V rail limit. Rail-to-rail output helps the amplifier produce useful output levels near the positive and negative supply rails, although input common-mode limits, output swing, noise, and stability still require verification for each design.

The TLV2432CD is offered in an 8-SOIC package and uses two independent amplifier channels. Typical circuit roles include voltage buffering, sensor-signal conditioning, transimpedance conversion, active filtering, and low-frequency closed-loop amplification. Because it is a CMOS operational amplifier, its quiescent behavior is suitable for battery-powered and portable equipment when the operating-current target is compatible with the device specification.

Typical applications include industrial sensor interfaces, portable measurement systems, audio signal conditioning, low-frequency control loops, and general-purpose dual-amplifier boards. Two amplifiers per package can reduce component count and PCB area when a design needs matched general-purpose channels. The same package also makes board-level substitutions more practical when the replacement has the same eight-pin pinout and acceptable electrical ratings.

For layout, place the decoupling capacitor close to the supply pin, connect exposed-sensitive signals away from power paths, and verify feedback-network stability with the actual load. Do not assume that a rail-to-rail output removes the need for output-headroom checks. Confirm input common-mode range, maximum output current, slew rate, noise, offset, and operating temperature against the manufacturer datasheet before production release.

This product page organizes the official device information, exact package identity, sourcing guidance, pin assignment, qualified drop-in alternatives, and practical design notes. It also provides parameter-by-parameter comparisons that help engineers evaluate replacements without confusing a footprint match with guaranteed electrical equivalence.

بدائل مباشرة لـ TLV2432CD — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.

الطرازات في هذه السلسلة

طرازات من نفس السلسلة متوافقة تمامًا مع TLV2432CD (نفس عامل الشكل والبصمة) — يختلف في Number of Channels, Package, Input Bias Current, Output Type, Slew Rate.

STMicroelectronics
Number of Channels: 2
Package: SOIC-8
Input Bias Current: 250 nA (max)
قارن مع TLV2432CD →
Microchip Technology
Number of Channels: 2 (dual)
Package: 8-pin SOIC (SN)
Input Bias Current: 1 pA (typical)

TLV2432CID

✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها
📦 8-SOIC, 3.90 mm width
Temperature-grade option differs from TLV2432CD; core 10 V, 500 kHz dual-amplifier architecture and 8-pin pinout remain compatible

📋 بديل مرجعي (غير موجود في الكتالوج)

TLV2432AID

✅ بديل مباشر
📦 8-SOIC, 3.90 mm width
A-series device has revised device characteristics versus TLV2432CD while retaining the compatible 8-pin SOIC footprint

📋 بديل مرجعي (غير موجود في الكتالوج)

TLV2432CDR

✅ بديل مباشر
📦 8-SOIC, 3.90 mm width
Tape-and-reel order configuration changes handling rather than the electrical ratings or 8-pin SOIC footprint

📋 بديل مرجعي (غير موجود في الكتالوج)

LMV358IDT

✅ بديل مباشر
STMicroelectronics
📦 8-SOIC, 3.90 mm width
2 · 2.7 V to 5.5 V · 210 µA · 1.3 MHz · 0.45 V/µs · 1 mV (max) · 250 nA (max) · 0 V to VCC - 1.1 V

✗ غير متوفر

$0.13 / وحدة

عرض ورقة البيانات ←

MCP6002-I/SN

✅ بديل مباشر
Microchip Technology
📦 8-SOIC, 3.90 mm width
2 (dual) · 1 MHz (typical) · 0.6 V/us (typical) · 1.8 V to 6.0 V · 100 uA (typical) · 1 pA (typical) · 90 degrees (typical)

تواصل لمعرفة السعر

عرض ورقة البيانات ←

TLV2432CD الحدود القصوى والخصائص الكهربائية

Amplifier Type Dual operational amplifier
Technology CMOS
Number of Channels 2 channels
Maximum Supply Voltage 10 V
Gain-Bandwidth Product 500 kHz
نوع الخرج Rail-to-rail output
العلبة 8-SOIC, 3.90 mm width
عدد الأطراف 8 pins
نوع التركيب Surface mount

تكوين أطراف TLV2432CD

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
دبوس 1 OUTA — Channel A output
دبوس 2 INA- — Channel A inverting input
دبوس 3 INA+ — Channel A non-inverting input
دبوس 4 V- — Negative supply connection
دبوس 5 INB+ — Channel B non-inverting input
دبوس 6 INB- — Channel B inverting input
دبوس 7 OUTB — Channel B output
دبوس 8 V+ — Positive supply connection

التطبيقات النموذجية

TLV2432CD مناسب لـ 6 التطبيقs: Industrial Sensor Signal Conditioning, Portable Battery-Powered Measurement, Audio Front-End Buffering, Precision Active Filtering, Motor and Power-Control Feedback, Data Acquisition and Interface Conditioning.

🏭

Industrial Sensor Signal Conditioning

The TLV2432CD is suitable for conditioning low-bandwidth sensor outputs because its dual-channel, 500 kHz gain-bandwidth-product design can provide buffering or gain without adding two separate amplifier packages. The 10 V maximum supply rating supports common industrial interface levels when the circuit operates within the complete recommended supply range. Place one channel in the signal-conditioning path and the other in a feedback, reference, or monitoring role. Verify the sensor output against the input common-mode range, and use a stable feedback network for the target gain and load.

📱

Portable Battery-Powered Measurement

The dual CMOS architecture of the TLV2432CD can reduce package count in portable measurement equipment where two low-frequency analog channels are required. Its 500 kHz bandwidth is ample for many temperature, pressure, and position sensors operating below the kilohertz range, while the 8-pin SOIC package is compatible with conventional PCB assembly. Because the device is powered from a limited battery rail, confirm quiescent current and the usable input range. The second amplifier may provide active filtering, offsetting, or a buffered reference.

🎧

Audio Front-End Buffering

The TLV2432CD can support low-frequency audio preamplifier or buffer stages when the signal bandwidth is well below its 500 kHz gain-bandwidth product. Rail-to-rail output is useful for driving a subsequent low-impedance stage within the available supply range, while two amplifiers allow signal conditioning and output buffering in one package. The design must still account for the amplifier’s noise, slew rate, output-current capability, and stable operation with the chosen feedback values and audio load.

📺

Precision Active Filtering

The TLV2432CD’s two channels can implement a second-order active filter or two coordinated single-stage filters in analog signal-conditioning systems. A 500 kHz gain-bandwidth product allows useful closed-loop bandwidth for low-frequency filtering, subject to the required Q factor, noise, and load. Check the amplifier’s gain-bandwidth and stability behavior using the intended feedback topology. For higher-order filters, distribute gain carefully and use the available grounded and bypass pins to minimize parasitic feedback and supply noise.

⚡

Motor and Power-Control Feedback

The TLV2432CD can implement low-frequency current, position, or error-amplifier functions in a power-control board because it provides two channels and a 500 kHz bandwidth for loops well below that value. Rail-to-rail output helps utilize the available control-signal range, but the 10 V maximum supply limits the operating environment. Verify output-current drive, slew rate, common-mode range, and stability against the motor-control circuitry rather than assuming generic op-amp performance is sufficient.

🖥️

Data Acquisition and Interface Conditioning

The TLV2432CD is appropriate for slow data-acquisition paths that require two channels of buffering or gain before an ADC or interface converter. The 500 kHz gain-bandwidth product supports bandwidths suitable for many low-rate sensors and control signals, and the 8-pin SOIC package simplifies routing on compact mixed-signal boards. Keep analog traces short, isolate them from switching paths, and place supply bypass capacitance at the IC. If the source has high impedance, verify input bias current and capacitance requirements rather than using the op amp as an unrestricted source follower.

What are the key specifications of TLV2432CD that engineers should know?
The TLV2432CD is a dual CMOS operational amplifier with a 10 V maximum supply voltage, 500 kHz gain-bandwidth product, rail-to-rail output capability, and an 8-pin SOIC package. Texas Instruments describes the TLV2432 family as a dual, 10 V, 500 kHz operational amplifier. The SOIC package contains two independent amplifier channels, which is useful for signal buffering, filtering, sensor conditioning, and other general-purpose analog functions.
What is the operating voltage of TLV2432CD?
The TLV2432CD has a maximum supply rating of 10 V. According to the Texas Instruments TLV2432 product page, the device is a 10 V dual operational amplifier, while the TLV2432CD ordering information identifies an 8-pin SOIC package. Confirm the complete operating supply range, input common-mode limits, and output-swing limits in the manufacturer datasheet before applying the amplifier to a specific rail.
Where can I download the TLV2432CD datasheet PDF?
The official TLV2432CD documentation is available through the Texas Instruments product page at https://www.ti.com/product/TLV2432. Use the datasheet link on that page for the manufacturer PDF, ordering information, electrical characteristics, and application details. The official part-details entry also identifies TLV2432CD as a dual, 10 V, 500 kHz operational amplifier in an 8-pin SOIC package.
Where can I find the TLV2432CD pinout?
The TLV2432CD pinout is the standard 8-pin SOIC arrangement used by the TLV2432 dual operational amplifier. According to the Texas Instruments pin-description table, pin 1 is OUTA, pins 2 and 3 are INA− and INA+, pin 4 is V−, pins 5 and 6 are INB+ and INB−, pin 7 is OUTB, and pin 8 is V+. Use the manufacturer pin-description table when assigning PCB tracks.
What can replace the TLV2432CD?
The TLV2432CD can be replaced only after confirming electrical and pin compatibility rather than package similarity alone. The LMV358 and MCP6002 are identified as pin-compatible alternatives, while same-family TLV2432 variants can offer different temperature or revision characteristics. The replacement must retain the 8-pin SOIC footprint and satisfy the original circuit’s bandwidth, supply, input range, output-current, noise, and stability requirements.
Is TLV2432CD the same as MCP6002?
The TLV2432CD and MCP6002 share an 8-pin operational-amplifier format, but they are not identical devices. The TLV2432CD is a Texas Instruments 10 V, 500 kHz dual CMOS amplifier, while the MCP6002 is a Microchip part with its own bandwidth, current, noise, and electrical characteristics. MCP6002 is a candidate drop-in replacement when its electrical limits satisfy the target application.
TLV2432CD vs LMV358: which is better for a low-frequency sensor circuit?
Choose the TLV2432CD when its 500 kHz bandwidth and 10 V supply rating align more closely with the original design. The LMV358 is a pin-compatible candidate for redesign, but its input range, output swing, quiescent current, noise, slew rate, and stability must be checked against the sensor output. The correct choice depends on the sensor impedance, gain, supply voltage, and required settling behavior.
When should I choose TLV2432CD over LMV358?
Choose TLV2432CD when preserving the original 500 kHz-bandwidth device behavior, 10 V supply class, and established layout is the priority. Consider LMV358 only after comparing its complete electrical characteristics with the TLV2432CD and confirming compatibility with the sensor, feedback network, load, and supply. Both devices use an 8-pin SOIC format, which simplifies PCB reuse but does not eliminate functional differences.
Is TLV2432CD suitable for battery-powered sensor interfaces?
The TLV2432CD can be suitable for low-voltage sensor interfaces because it is a dual CMOS operational amplifier that combines two channels in one 8-pin SOIC package. Suitability depends on the exact supply voltage, quiescent current, input common-mode range, and output swing. Verify those specifications against the battery operating range and the sensor’s output voltage before fixing the design.
Where can I buy TLV2432CD online?
Use the Request a Quote form on this page to ask for TLV2432CD availability, current unit pricing, quantity breaks, and lead time. The request can specify the required 8-pin SOIC configuration and production quantity. Confirm any quotation against the exact manufacturer part number and inspect the latest manufacturer ordering information before releasing components.
What is the price of TLV2432CD?
Current TLV2432CD pricing is best obtained through the Request a Quote form on this page because commercial terms and availability can change with quantity and market conditions. State the required quantity, packaging preference, target date, and acceptable ship-to location in the request. The form provides a focused way to request current pricing without relying on an outdated historical listing.
What is the lead time for TLV2432CD?
Request the current TLV2432CD lead time through the Request a Quote form on this page. Include your required quantity, production schedule, and shipment destination so the quotation can reflect the actual order. For design planning, treat any lead-time statement as order-specific until a written quotation and order acknowledgment confirm it.
Is TLV2432CD in stock?
Request current TLV2432CD stock status through the Request a Quote form on this page because availability can change by package configuration, order quantity, and shipment region. Provide the exact MPN and required quantity, and request an availability confirmation with the quotation. The manufacturer part-details page identifies TLV2432CD as an 8-pin SOIC device for order planning.
Does TLV2432CD need a decoupling capacitor?
Yes, the TLV2432CD supply should be bypassed with suitable local decoupling to control impedance and reduce supply disturbance on both supply rails. Place the capacitor close to the SOIC supply pins and connect the return path directly to the device ground. Select the capacitance and voltage rating using the manufacturer application guidance and the impedance and transient requirements of the circuit.
Is TLV2432CD RoHS compliant and automotive qualified?
The RoHS and AEC-Q100 status of TLV2432CD must be confirmed from the current manufacturer product and ordering documentation before an automotive or environmental-compliance claim is made. The device is a commercial dual CMOS operational amplifier in an 8-pin SOIC package, but package identity alone does not establish RoHS, REACH, lead-free, halogen-free, or automotive qualification. Request the applicable declarations for the exact orderable MPN.

بيانات مرجعية هندسية لـ TLV2432CD — المقارنة وإرشادات التصميم ومعلومات الامتثال.

دليل الاختيار

Choose TLV2432CD when maintaining the original 10 V, 500 kHz dual CMOS amplifier design is important, particularly when the existing PCB uses the 8-pin SOIC footprint and the circuit depends on established rail-to-rail-output behavior. TLV2432CID and TLV2432CDR are the closest same-family choices when temperature grade or tape-and-reel handling is the deciding factor. Consider LMV358 when its electrical characteristics and current consumption better match the revised circuit while preserving the SOIC pin arrangement. Consider MCP6002 for a cross-manufacturer sourcing option after checking bandwidth, input range, output swing, noise, stability, and lifecycle requirements. For any substitution, compare the complete manufacturer datasheets rather than relying on the package or nominal amplifier function alone.

المقارنة مع البدائل

المعامل هذا المنتج TLV2432CID TLV2432AID TLV2432CDR LMV358 MCP6002
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Microchip Technology
Package 8-SOIC, 3.90 mm width 8-SOIC, 3.90 mm width 8-SOIC, 3.90 mm width 8-SOIC, 3.90 mm width 8-SOIC, 3.90 mm width 8-SOIC, 3.90 mm width
Channel Count 2 channels 2 channels 2 channels 2 channels 2 channels 2 channels
Technology CMOS CMOS CMOS CMOS CMOS CMOS
Output Type Rail-to-rail output Rail-to-rail output Rail-to-rail output Rail-to-rail output Rail-to-rail output Rail-to-rail output
Pin Count 8 pins 8 pins 8 pins 8 pins 8 pins 8 pins
Order Configuration TLV2432CD tube shipment configuration Industrial temperature-grade order option A-series device option Tape-and-reel order configuration General-purpose dual rail-to-rail amplifier General-purpose dual CMOS amplifier

أبرز الفروقات

  • Two amplifier channels in one package (مقابلMCP6002)
  • 500 kHz gain-bandwidth product (مقابلLMV358)
  • Direct same-family replacement path (مقابلTLV2432AID)

ملاحظات التصميم

Place the supply-bypass capacitor immediately across the positive and negative supply pins of the TLV2432CD, with a short, low-inductance return to the device ground. Select capacitance and voltage rating from the manufacturer stability and application guidance. In mixed-signal systems, keep the analog return current separate from high-current switching paths so supply disturbance does not couple directly into the amplifier inputs.

Route the two input nets as short and symmetric as practical, and keep them away from switching nodes, inductors, and the return path of power devices. The 8-pin SOIC footprint leaves little room around the package, so place feedback resistors and input or output protection components close to their associated pins. A compact ground reference near pin 4 helps reduce parasitic inductance in the supply-bypass loop.

Do not treat rail-to-rail output as an unlimited output range. Check the datasheet output-voltage swing under the actual load and output-current condition, and confirm that the input common-mode range includes the signal at every operating point. Also avoid assuming a unity-gain configuration is stable with every capacitive load; model the load and evaluate the feedback network before production.

معلومات الامتثال

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
خالٍ من الرصاص
Unknown
خالٍ من الهالوجين
Unknown
المعادن المتنازع عليها
Unknown

Compliance declarations were not identified in the manufacturer page excerpts. Confirm the exact orderable MPN with Texas Instruments before making RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals claims.

تم التحقق من البيانات في: 2026-11-15 — تم التحقق من البيانات وتنسيقها بواسطة فريق هندسة المكونات في XAIPART

عمليات بحث ذات صلة

TLV2432CD datasheet TLV2432CD pinout TLV2432CD datasheet pdf TLV2432CD equivalent TLV2432CD replacement TLV2432CD cross reference TLV2432CD vs LMV358 TLV2432CD vs MCP6002 TLV2432CD price TLV2432CD stock Texas Instruments TLV2432CD TLV2432CD 8-SOIC pinout TLV2432CD sensor signal conditioning TLV2432CD 500kHz amplifier TLV2432CD schematic

المكونات والمصطلحات ذات الصلة

Texas Instruments TLV2432CD TLV2432 TLV2432CID TLV2432AID TLV2432CDR LMV358 MCP6002 operational amplifier CMOS operational amplifier dual amplifier rail-to-rail output gain-bandwidth product input common-mode range output swing 8-SOIC SOIC package family surface-mount package sensor signal conditioning active filtering audio preamplifier industrial control battery-powered measurement data acquisition
عرض سعر سريع RFQ
املأ التفاصيل الكاملة — سيرد فريق المبيعات لدينا خلال 24 ساعة
رقم القطعة الشركة المصنعة الحزمة QTY السعر المستهدف الإجمالي
✓
تم إرسال عرض السعر!

سنرد على بريدك الإلكتروني خلال 24 ساعة

1
تم إرسال طلب عرض السعر
2
تم استلام عرض السعر
3
تم تقديم الطلب
4
الدفع
5
تم الشحن
6
تم التسليم
عرض تفاصيل طلب عرض السعر