TLV2432CD - Dual 10V 500kHz Rail-to-Rail Op Amp | TI
MPN: TLV2432CD ✓ פעילTLV2432CD סקירה
An operational amplifier is an analog building block used to amplify voltage differences, buffer signals, integrate errors, and drive control inputs. The TLV2432 belongs to the CMOS operational-amplifier hierarchy and is designed for low-voltage signal conditioning where two channels, rail-to-rail output swing, and low supply current can simplify a board design.
The device is identified as a CMOS, dual-amplifier circuit with rail-to-rail output operation. Its 500 kHz bandwidth is suitable for low-to-moderate-frequency instrumentation, while the 10 V supply rating positions it for circuits operating below the 10 V rail limit. Rail-to-rail output helps the amplifier produce useful output levels near the positive and negative supply rails, although input common-mode limits, output swing, noise, and stability still require verification for each design.
The TLV2432CD is offered in an 8-SOIC package and uses two independent amplifier channels. Typical circuit roles include voltage buffering, sensor-signal conditioning, transimpedance conversion, active filtering, and low-frequency closed-loop amplification. Because it is a CMOS operational amplifier, its quiescent behavior is suitable for battery-powered and portable equipment when the operating-current target is compatible with the device specification.
Typical applications include industrial sensor interfaces, portable measurement systems, audio signal conditioning, low-frequency control loops, and general-purpose dual-amplifier boards. Two amplifiers per package can reduce component count and PCB area when a design needs matched general-purpose channels. The same package also makes board-level substitutions more practical when the replacement has the same eight-pin pinout and acceptable electrical ratings.
For layout, place the decoupling capacitor close to the supply pin, connect exposed-sensitive signals away from power paths, and verify feedback-network stability with the actual load. Do not assume that a rail-to-rail output removes the need for output-headroom checks. Confirm input common-mode range, maximum output current, slew rate, noise, offset, and operating temperature against the manufacturer datasheet before production release.
This product page organizes the official device information, exact package identity, sourcing guidance, pin assignment, qualified drop-in alternatives, and practical design notes. It also provides parameter-by-parameter comparisons that help engineers evaluate replacements without confusing a footprint match with guaranteed electrical equivalence.
חלופות תחליף ישיר עבור TLV2432CD — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
וריאנטים בסדרה זו
דגמים מאותה סדרה התואמים Drop-in עם TLV2432CD (אותו גורם צורה וטביעת רגל) — שונים ב Number of Channels, Package, Input Bias Current, Output Type, Slew Rate.
TLV2432CID
✅ Drop-In ⚠️ מפרטים לא מאומתים📋 חלופה להתייחסות (לא בקטלוג)
TLV2432AID
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
TLV2432CDR
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
LMV358IDT
✅ Drop-In✗ אזל מהמלאי
$0.13 / יחידה
הצג גיליון נתונים ←MCP6002-I/SN
✅ Drop-Inצור קשר לקבלת מחיר
הצג גיליון נתונים ←TLV2432CD דירוגים מרביים ומאפיינים חשמליים
| Amplifier Type | Dual operational amplifier |
| Technology | CMOS |
| Number of Channels | 2 channels |
| Maximum Supply Voltage | 10 V |
| Gain-Bandwidth Product | 500 kHz |
| סוג פלט | Rail-to-rail output |
| מארז | 8-SOIC, 3.90 mm width |
| מספר פינים | 8 pins |
| סוג הרכבה | Surface mount |
תצורת פינים של TLV2432CD
| פין 1 | OUTA — Channel A output |
| פין 2 | INA- — Channel A inverting input |
| פין 3 | INA+ — Channel A non-inverting input |
| פין 4 | V- — Negative supply connection |
| פין 5 | INB+ — Channel B non-inverting input |
| פין 6 | INB- — Channel B inverting input |
| פין 7 | OUTB — Channel B output |
| פין 8 | V+ — Positive supply connection |
יישומים טיפוסיים
TLV2432CD מתאים עבור 6 יישוםs: Industrial Sensor Signal Conditioning, Portable Battery-Powered Measurement, Audio Front-End Buffering, Precision Active Filtering, Motor and Power-Control Feedback, Data Acquisition and Interface Conditioning.
Industrial Sensor Signal Conditioning
The TLV2432CD is suitable for conditioning low-bandwidth sensor outputs because its dual-channel, 500 kHz gain-bandwidth-product design can provide buffering or gain without adding two separate amplifier packages. The 10 V maximum supply rating supports common industrial interface levels when the circuit operates within the complete recommended supply range. Place one channel in the signal-conditioning path and the other in a feedback, reference, or monitoring role. Verify the sensor output against the input common-mode range, and use a stable feedback network for the target gain and load.
מומלץ
Portable Battery-Powered Measurement
The dual CMOS architecture of the TLV2432CD can reduce package count in portable measurement equipment where two low-frequency analog channels are required. Its 500 kHz bandwidth is ample for many temperature, pressure, and position sensors operating below the kilohertz range, while the 8-pin SOIC package is compatible with conventional PCB assembly. Because the device is powered from a limited battery rail, confirm quiescent current and the usable input range. The second amplifier may provide active filtering, offsetting, or a buffered reference.
מומלץ
Audio Front-End Buffering
The TLV2432CD can support low-frequency audio preamplifier or buffer stages when the signal bandwidth is well below its 500 kHz gain-bandwidth product. Rail-to-rail output is useful for driving a subsequent low-impedance stage within the available supply range, while two amplifiers allow signal conditioning and output buffering in one package. The design must still account for the amplifier’s noise, slew rate, output-current capability, and stable operation with the chosen feedback values and audio load.
מומלץ
Precision Active Filtering
The TLV2432CD’s two channels can implement a second-order active filter or two coordinated single-stage filters in analog signal-conditioning systems. A 500 kHz gain-bandwidth product allows useful closed-loop bandwidth for low-frequency filtering, subject to the required Q factor, noise, and load. Check the amplifier’s gain-bandwidth and stability behavior using the intended feedback topology. For higher-order filters, distribute gain carefully and use the available grounded and bypass pins to minimize parasitic feedback and supply noise.
מומלץ
Motor and Power-Control Feedback
The TLV2432CD can implement low-frequency current, position, or error-amplifier functions in a power-control board because it provides two channels and a 500 kHz bandwidth for loops well below that value. Rail-to-rail output helps utilize the available control-signal range, but the 10 V maximum supply limits the operating environment. Verify output-current drive, slew rate, common-mode range, and stability against the motor-control circuitry rather than assuming generic op-amp performance is sufficient.
מומלץ
Data Acquisition and Interface Conditioning
The TLV2432CD is appropriate for slow data-acquisition paths that require two channels of buffering or gain before an ADC or interface converter. The 500 kHz gain-bandwidth product supports bandwidths suitable for many low-rate sensors and control signals, and the 8-pin SOIC package simplifies routing on compact mixed-signal boards. Keep analog traces short, isolate them from switching paths, and place supply bypass capacitance at the IC. If the source has high impedance, verify input bias current and capacitance requirements rather than using the op amp as an unrestricted source follower.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור TLV2432CD — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | TLV2432CID | TLV2432AID | TLV2432CDR | LMV358 | MCP6002 |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Microchip Technology |
| Package | 8-SOIC, 3.90 mm width | 8-SOIC, 3.90 mm width | 8-SOIC, 3.90 mm width | 8-SOIC, 3.90 mm width | 8-SOIC, 3.90 mm width | 8-SOIC, 3.90 mm width |
| Channel Count | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels |
| Technology | CMOS | CMOS | CMOS | CMOS | CMOS | CMOS |
| Output Type | Rail-to-rail output | Rail-to-rail output | Rail-to-rail output | Rail-to-rail output | Rail-to-rail output | Rail-to-rail output |
| Pin Count | 8 pins | 8 pins | 8 pins | 8 pins | 8 pins | 8 pins |
| Order Configuration | TLV2432CD tube shipment configuration | Industrial temperature-grade order option | A-series device option | Tape-and-reel order configuration | General-purpose dual rail-to-rail amplifier | General-purpose dual CMOS amplifier |
מבדילים עיקריים
- Two amplifier channels in one package (לעומתMCP6002)
- 500 kHz gain-bandwidth product (לעומתLMV358)
- Direct same-family replacement path (לעומתTLV2432AID)
הערות תכנון
Place the supply-bypass capacitor immediately across the positive and negative supply pins of the TLV2432CD, with a short, low-inductance return to the device ground. Select capacitance and voltage rating from the manufacturer stability and application guidance. In mixed-signal systems, keep the analog return current separate from high-current switching paths so supply disturbance does not couple directly into the amplifier inputs.
Route the two input nets as short and symmetric as practical, and keep them away from switching nodes, inductors, and the return path of power devices. The 8-pin SOIC footprint leaves little room around the package, so place feedback resistors and input or output protection components close to their associated pins. A compact ground reference near pin 4 helps reduce parasitic inductance in the supply-bypass loop.
Do not treat rail-to-rail output as an unlimited output range. Check the datasheet output-voltage swing under the actual load and output-current condition, and confirm that the input common-mode range includes the signal at every operating point. Also avoid assuming a unity-gain configuration is stable with every capacitive load; model the load and evaluate the feedback network before production.
מידע על תאימות
Compliance declarations were not identified in the manufacturer page excerpts. Confirm the exact orderable MPN with Texas Instruments before making RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals claims.