TPS54335ADRCR - 4.5-28V In, 3A Sync Buck Converter | TI
MPN: TPS54335ADRCR ✓ نشطTPS54335ADRCR نظرة عامة
A synchronous buck converter is a switching voltage regulator that uses high-side and low-side MOSFETs (instead of a diode) to step a higher input voltage down to a lower, tightly regulated output. Within the power management IC hierarchy, the TPS54335A sits in the switching regulator family, which achieves far higher efficiency than linear regulators (LDOs) because energy is transferred in switched inductor cycles rather than dissipated as heat.
Key features include integrated 128 mOhm high-side and 84 mOhm low-side MOSFETs supporting 3 A continuous output current, an adjustable switching frequency from 50 kHz to 1.5 MHz set by a single external resistor, and an internal 2 ms soft-start on the TPS54335A variant. TI Eco-mode circuitry pulses the converter at light loads to maintain high efficiency down to microamp-level loads, with only 2 uA shutdown current.
Technically, the device uses peak current-mode control with cycle-by-cycle overcurrent limiting, thermal shutdown, and input undervoltage lockout. The wide 4.5-28 V input accommodates 5 V, 12 V, and unregulated 24 V industrial rails. Output voltage is set by an external resistor divider from 0.8 V upward.
Typical applications include 5 V and 12 V distributed power buses, industrial automation point-of-load supplies, and consumer/appliance onboard power where small size and high efficiency matter.
Design consideration: because switching frequency is adjustable, trade efficiency (lower frequency) against inductor size and transient response (higher frequency); keep the RT resistor trace short to limit noise pickup.
This page synthesizes verified distributor pricing, drop-in alternatives, design notes, and application guidance not found in a single manufacturer datasheet.
بدائل مباشرة لـ TPS54335ADRCR — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
TPS54335ADRCT
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
TPS54335-1ADRCR
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
TPS54336ADRCR
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
TPS54334DRCR
✅ بديل مباشر📋 بديل مرجعي (غير موجود في الكتالوج)
TPS54335ADRCR الحدود القصوى والخصائص الكهربائية
| البنية الطوبولوجية | Synchronous Step-Down (Buck) Converter |
| نطاق جهد الدخل | 4.5 V to 28 V |
| جهد الخرج | Adjustable from 0.8 V |
| أقصى تيار خرج | 3 A |
| عدد المخارج | 1 |
| تردد التبديل | 50 kHz to 1.5 MHz (adjustable) |
| مقاومة التشغيل لـ MOSFET الجانب العالي | 128 mOhm (integrated) |
| مقاومة التشغيل لـ MOSFET الجانب المنخفض | 84 mOhm (integrated) |
| بدء التشغيل الناعم | Internal 2 ms (TPS54335A) |
| تيار الإيقاف | 2 uA |
| Light-Load Mode | Eco-mode |
| نطاق درجة حرارة التشغيل | -40C to +150C |
| العلبة | 10-VFDFN Exposed Pad (VSON / DRC), 10 pins |
| نوع التركيب | Surface Mount |
| نوع الخرج | Positive Adjustable |
| حالة RoHS | Compliant |
| Control Topology | Peak Current Mode |
تكوين أطراف TPS54335ADRCR
| دبوس 1 | BOOT — Bootstrap capacitor connection for high-side gate driver |
| دبوس 2 | VIN — Input supply voltage, 4.5 V to 28 V |
| دبوس 3 | EN — Enable input with internal UVLO; pull high to enable |
| دبوس 4 | RT/CLK — Switching frequency programming resistor or external clock input |
| دبوس 5 | SS/TR — Soft-start / tracking pin (internal 2 ms soft-start on TPS54335A) |
| دبوس 6 | GND — Ground reference and thermal path (with exposed pad) |
| دبوس 7 | COMP — Error amplifier output for loop compensation network |
| دبوس 8 | VSENSE — Feedback input; connect to output resistor divider |
| دبوس 9 | PWRGD — Open-drain power good status output |
| دبوس 10 | PH — Switch phase node connecting integrated MOSFETs to inductor |
التطبيقات النموذجية
TPS54335ADRCR مناسب لـ 6 التطبيقs: 12V Distributed Power Bus Point-of-Load, 24V Industrial Automation Supplies, 5V and 12V Onboard Appliance Power, Consumer Electronics DC-DC Regulation, LED Driver and Lighting Power Front Ends, Battery-Powered and Portable Instrumentation.
12V Distributed Power Bus Point-of-Load
The TPS54335A fits 12 V intermediate bus point-of-load conversion because its 4.5-28 V input range directly accepts 12 V rails with headroom for transients, while its integrated 128 mOhm and 84 mOhm MOSFETs deliver 3 A continuous without external power stages. In a typical 12 V to 3.3 V or 12 V to 1.8 V supply, the peak current-mode architecture provides fast load transient response for processors and FPGAs. Eco-mode keeps efficiency high when subsystem loads drop to standby, and the 2 uA shutdown current supports system-level power gating. The adjustable 50 kHz-1.5 MHz frequency lets designers choose small inductors at 1 MHz+ for dense boards or lower frequencies for peak efficiency.
موصى به
24V Industrial Automation Supplies
Industrial PLCs, motor-control boards, and field I/O modules commonly run from unregulated 24 V rails that can swing well above nominal; the TPS54335A's 28 V maximum input provides direct conversion without a pre-regulator stage. Its cycle-by-cycle overcurrent limit and thermal shutdown survive fault events common in factory environments, while the wide adjustable output from 0.8 V supports 5 V logic, 3.3 V microcontroller, and low-voltage analog rails from one converter family. Setting the switching frequency below 500 kHz reduces switching losses at high continuous loads typical of industrial duty cycles, and the exposed-pad DRC package dissipates heat effectively into a ground-plane copper pour on standard industrial PCB stackups.
موصى به
5V and 12V Onboard Appliance Power
White goods, HVAC controllers, and smart appliances need compact, efficient step-down conversion from mains-derived 12 V or 5 V auxiliaries; the TPS54335A's synchronous topology exceeds 90 percent efficiency at mid loads, reducing internal heat rise in sealed enclosures. The internal 2 ms soft-start eliminates the need for an external soft-start capacitor and controls inrush into downstream bulk capacitance, while Eco-mode maintains efficiency during appliance standby states subject to energy regulations. Its integrated MOSFETs shrink the bill of materials compared with controller-plus-discrete designs, and the 10-pin VSON package keeps solution size small on cost-driven two-layer appliance boards where layout area is at a premium.
موصى به
Consumer Electronics DC-DC Regulation
Set-top boxes, networking peripherals, and audio-visual equipment benefit from the TPS54335A's combination of small size and low-noise potential. Running the adjustable frequency above 1 MHz moves switching harmonics away from sensitive audio and RF bands, and pushes passive components smaller for dense consumer boards. The device's 3 A capacity comfortably powers SoC cores, memory, and I/O rails simultaneously when output networks are scaled appropriately, and its peak current-mode loop is straightforward to compensate with a single Type-II network on COMP. Eco-mode reduces input draw at standby, helping products meet standby-power limits, while the 2 uA shutdown suits battery-backup and soft-off circuit paths in consumer designs.
موصى به
LED Driver and Lighting Power Front Ends
The TPS54335A can serve as the regulated front-end supply for LED luminaires and signage controllers, converting 12 V or 24 V inputs down to logic and driver-supply rails with high efficiency. Its wide input tolerance handles dimmer and mains-rectified bus variation, and the adjustable frequency allows coordination with PWM dimming stages to avoid beat-frequency artifacts in visible light output. Integrated protection (overcurrent, thermal shutdown, UVLO) improves field reliability in thermally constrained luminaire housings where airflow is absent. Because the buck operates synchronously, efficiency remains high even at partial dimming levels where load current falls, thanks to Eco-mode pulse-skipping behavior at light load.
موصى به
Battery-Powered and Portable Instrumentation
Portable test instruments and battery-operated sensors draw from multi-cell packs whose voltage sags over discharge; the TPS54335A's 4.5 V minimum input supports 5-cell lithium chemistries and its Eco-mode maximizes run time during low-duty measurement cycles. The 2 uA shutdown current lets the system MCU cut converter power entirely between samples. At active loads up to 3 A, the synchronous MOSFETs minimize conduction loss, extending battery life versus non-synchronous buck alternatives that lose diode drops. The exposed-pad DRC package supports compact handheld PCB layouts, and the adjustable soft-start behavior of the internal 2 ms ramp prevents excessive battery inrush current at power-up in current-limited packs.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ TPS54335ADRCR — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | TPS54335ADRCT | TPS54335-1ADRCR | TPS54336ADRCR | TPS54334DRCR | TPS54335DDA |
|---|---|---|---|---|---|---|
| Package | VSON-10 (DRC) Exposed Pad | VSON-10 (DRC) - same | VSON-10 (DRC) - same | VSON-10 (DRC) - same | VSON-10 (DRC) - same | SO-8 PowerPAD - different footprint |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
أبرز الفروقات
- Wide adjustable frequency range for design optimization (مقابلTPS54336ADRCR)
- Zero external soft-start component cost (مقابلTPS54336ADRCR)
- High efficiency from low-Rds(on) synchronous MOSFETs (مقابلNon-synchronous 3 A buck alternatives)
ملاحظات التصميم
Place the input ceramic decoupling capacitor (typically 10 uF) within 2-3 mm of VIN and GND to minimize the high-frequency loop containing the input cap, integrated high-side MOSFET, PH node, and low-side MOSFET. Keep the PH-to-inductor trace short and wide. Connect the exposed thermal pad to a solid ground plane with a 4x4 via array under the DRC package - the pad is the primary thermal and electrical ground path. Route the RT resistor away from the SW/PH node to avoid frequency jitter from switching noise coupling.
Estimated: at VIN=24 V, VOUT=5 V, and full 3 A load, converter loss of roughly 1.2-1.5 W (at ~90 percent efficiency) in the DRC package will raise junction temperature significantly above ambient; with an effective theta_JA of about 40-50 C/W on a good 2-layer layout (2 oz copper), expect a 50-75 C rise. Verify junction temperature stays below the datasheet limit at worst-case ambient, and add copper area or airflow for high-ambient industrial enclosures. Consult the TI datasheet thermal application section for the exact theta_JA of your stackup.
Do not exceed the 28 V absolute maximum input rating - unregulated 24 V industrial supplies can transient above this; add input TVS or a surge-rated input stage if the rail is unprotected. Ensure the BOOT capacitor (typically 0.1 uF) is placed directly across BOOT and PH. When using the adjustable frequency range, respect the datasheet minimum on-time constraints at high VIN to avoid pulse-skipping or output ripple degradation. Verify EN pin UVLO divider sets an appropriate turn-on threshold for your input source.
معلومات الامتثال
RoHS compliant per distributor listings. REACH, halogen-free, and conflict-minerals status not stated in provided data.
