STMicroelectronics

TS3702ID - Micropower Dual CMOS Comparator, 9uA, SOIC-8 | STMicroelectronics

N.º de pieza: TS3702ID ✓ Activo
2.7 V to 16 V Vdss 9 uA typical Id 8-pin SOIC-8 (SO-8), surface mount Package
MOQ: 1 |

TS3702ID Descripción general

The STMicroelectronics TS3702ID is a micropower dual CMOS voltage comparator that integrates two independent general-purpose comparators in an 8-pin SOIC-8 (SO-8) surface-mount package. Each channel consumes only 9 uA typical supply current, presents a 10^12 ohm typical input impedance and offers a 2.3 us typical response time, making it roughly twenty times lower in consumption than the classic bipolar LM393 reference circuit.

A voltage comparator is an analog integrated circuit that compares two input voltages and switches its output according to which input is higher. As a sub-type of the amplifier family, a comparator sits between raw sensing elements and a digital control path: it belongs to the broader hierarchy of analog ICs, amplifiers and comparators, signal conditioning, and ultimately power management and interface ICs. Its job is to translate a small analog difference into a logic-level decision without introducing supply noise or consuming significant battery current.

Key features of the TS3702ID include a push-pull CMOS output stage, which removes the external pull-up resistor normally required by open-collector comparators and saves both board area and standby current. The device accepts a single supply from 2.7 V to 16 V or dual supplies from +/-1.35 V to +/-8 V, operates down to ground at the input common-mode range, and draws only 1 pA typical input offset current. The manufacturer also specifies pin-to-pin and functional compatibility with the bipolar LM393, which eases migration between designs.

Internally the TS3702ID uses a CMOS process, giving near-zero input bias current and rail-to-rail CMOS output levels rather than saturated bipolar levels. The push-pull stage sources and sinks current actively, so output transitions are fast and the logic levels remain valid at low supply voltages where open-collector comparators would need extra headroom to guarantee a valid high level.

Typical applications include battery-powered sensor and threshold monitoring, window comparators for over/undervoltage detection, low-current alarm and wake-up circuits, portable instrumentation, and general-purpose level detection in industrial control boards.

When designing with the TS3702ID, remember that the output stage is push-pull, not open-collector, so no external pull-up resistor should be added. Confirm the input common-mode limits against the actual supply voltage in the manufacturer datasheet, and keep the input bias network impedance high so the 1 pA offset current does not shift the threshold.

This page consolidates the manufacturer datasheet figures, distributor availability, package details, drop-in alternatives and practical design notes into one engineering reference that goes beyond the raw component listing.

Alternativas directas para TS3702ID — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.

Variantes de esta serie

Modelos de la misma serie compatibles directamente con TS3702ID (mismo factor de forma y huella) — difiere en Operating Temperature Range, Output Type, Package.

Texas Instruments
Operating Temperature Range: 0°C to +70°C (LM393 commercial grade)
Output Type: Open-collector, rail-to-rail input capable
Package: SOIC-8 (D suffix)
Comparar con TS3702ID →

TS3702CDT

✅ Sustitución directa
📦 SOIC-8 (SO-8)
Same TS3702 dual comparator die and SOIC-8 footprint, but commercial temperature grade (-40 C to +85 C) instead of the -40 C to +125 C industrial rating of the TS3702ID; same 9 uA per comparator and push-pull CMOS output

📋 Alternativa de referencia (no en el catálogo)

TS3702IDT

✅ Sustitución directa
📦 SOIC-8 (SO-8)
Identical electrical specification to the TS3702ID (9 uA per comparator, push-pull CMOS output, 2.7 V to 16 V) supplied in tape-and-reel rather than tube packing, so pin and function compatibility is 100%

📋 Alternativa de referencia (no en el catálogo)

TS3702CD

✅ Sustitución directa ⚠️ Especificaciones sin verificar
STMicroelectronics
📦 SOIC-8 (SO-8)
Dual general-purpose voltage comparator · 2 channels · 9 uA typical · 2 us typical · 10^12 ohm typical · 6.5 mV · Push-pull CMOS · Single or dual supply

Consulte el precio

Ver hoja de datos →

LM393

✅ Sustitución directa
Texas Instruments
📦 SOIC-8 (SO-8)
2 (dual independent) · 2 V to 30 V · ±1 V to ±15 V · 2.0 mV (typical) · ±38 V · Includes ground (V-) · Open-collector, rail-to-rail input capable · TTL, MOS, CMOS (with external pull-up)

Consulte el precio

Ver hoja de datos →

LMV393

✅ Sustitución directa ⚠️ Especificaciones sin verificar
📦 SOIC-8 (SO-8)
Micropower dual comparator in the same SOIC-8 LM393-style footprint, but the output stage is open-collector so a pull-up resistor is needed where the TS3702ID push-pull stage needs none, and the supply current per channel is higher than 9 uA

📋 Alternativa de referencia (no en el catálogo)

TS3702ID Valores máximos y características eléctricas

Number of Comparators 2
Comparator Type General purpose voltage comparator
Supply Voltage Range (Single) 2.7 V to 16 V
Supply Voltage Range (Dual) +/-1.35 V to +/-8 V
Supply Current per Comparator 9 uA typical
Input Impedance 10^12 ohm typical
Input Offset Current 1 pA typical
Response Time 2.3 us typical
Tipo de salida Push-pull CMOS
External Pull-up Resistor Required No
Input Common-Mode Range Includes GND
LM393 Compatibility Pin-to-pin and functionally compatible with bipolar LM393
Rango de temperatura de funcionamiento -40 C to +125 C
Encapsulado 8-pin SOIC-8 (SO-8), surface mount
Marking Code 3702I

Configuración de pines de TS3702ID

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
Pin 1 OUT1 — Comparator 1 output, push-pull CMOS
Pin 2 IN1- — Comparator 1 inverting input
Pin 3 IN1+ — Comparator 1 non-inverting input
Pin 4 V- — Negative supply / ground reference pin
Pin 5 IN2+ — Comparator 2 non-inverting input
Pin 6 IN2- — Comparator 2 inverting input
Pin 7 OUT2 — Comparator 2 output, push-pull CMOS
Pin 8 V+ — Positive supply pin

Aplicaciones típicas

TS3702ID es adecuado para 6 aplicacións: Battery Threshold Monitoring, Window Comparator for Over/Undervoltage, Portable Instrument Sensor Conditioning, Industrial Level and Limit Detection, Battery Charger and Power Path Cutoff, Automotive and Off-Highway Sensing Node.

🔋

Battery Threshold Monitoring

The TS3702ID suits low-power battery supervision because each channel draws only 9 uA typical while presenting a 10^12 ohm input impedance that does not load the cell voltage divider. A resistive divider feeding IN+ and the reference on IN- gives a window or simple threshold detector whose trip point drifts only with resistor tolerance and temperature, since the 1 pA typical input offset current barely loads the sensing network. With the push-pull CMOS output the alarm signal drives a microcontroller input directly, no external pull-up resistor and no continuous bias current is needed, which helps extend the service interval of the powered node compared with an open-collector LM393 arrangement using a permanently biased resistor.

⚡

Window Comparator for Over/Undervoltage

Using the two independent channels of the TS3702ID as a window detector allows one 8-pin SOIC-8 to signal both overvoltage and undervoltage on a rail. The two channels share the same supply pins, so the whole detector adds about 18 uA of load regardless of rail voltage, and the operating range of 2.7 V to 16 V single supply or +/-1.35 V to +/-8 V dual supply lets the same part monitor a regulated 5 V rail or a +/-12 V analog node. The 2.3 us typical response time is short enough to trip before the protected rail leaves tolerance, and the push-pull output means the fault signal is a valid CMOS level with no pull-up resistor and no added quiescent current.

📱

Portable Instrument Sensor Conditioning

In handheld and wearable measurement equipment the TS3702ID converts a small sensor differential into a logic decision with almost no standing current cost. The 10^12 ohm typical input impedance means the transducer bridge or resistive ladder is barely loaded, so the threshold setpoint stays accurate, and the 1 pA typical input offset current keeps the input bias error below the resolution of most low-cost sensors. Because the device operates from 2.7 V, it fits single-cell powered designs, and the wide -40 C to +125 C rating covers products that are specified for both consumer and industrial environments. The push-pull output drives the display or radio control line without the extra resistor an open-collector part would demand.

🏭

Industrial Level and Limit Detection

The TS3702ID works well as a limit detector on tanks, pipes and machine tools where a sensor output must be turned into a discrete event. Its 2.3 us typical response time and push-pull CMOS output give fast, valid logic levels that can drive a PLC input or a safety relay stage without level-shifting, and the industrial -40 C to +125 C grade keeps behaviour predictable in unheated cabinets and outdoor enclosures. Because the input common-mode range includes ground, sensor outputs referenced to 0 V can be compared directly, and the extremely high input impedance allows long sensor wiring without the comparator biasing the line.

🔋

Battery Charger and Power Path Cutoff

In charger and power-path designs the TS3702ID provides a fast, low-current cutoff decision on the battery terminal. The 9 uA typical per comparator is small enough not to distort the standby current budget of a charger module, while the 2.7 V minimum single supply allows the comparator to stay active across the useful cell range. When the fast response time of 2.3 us detects an out-of-window condition, the push-pull output directly enables or disables the next stage in the chain. Because the output actively sources and sinks, the same footprint works with CMOS control logic and with the level-shifting arrangements common in automotive and industrial power modules.

🚗

Automotive and Off-Highway Sensing Node

The TS3702ID suits off-highway and body electronics sensing nodes where a wide ambient range and low standby current both matter. The -40 C to +125 C operating range tolerates engine bay and unheated body compartment temperatures, and the 9 uA per comparator keeps the quiescent draw of a parked vehicle node low enough for the battery to survive long storage periods. The push-pull CMOS output gives a clean logic signal into the body network transceiver, avoiding the pull-up resistor and its associated current that an open-collector LM393 substitute would require. Its pin compatibility with the LM393 footprint also eases reuse of existing board spares.

Resumen de productos recomendados

TS3702IDT same comparator in tape-and-reel for volume production Se usa en: Battery Threshold Monitoring, Window Comparator for Over/Undervoltage, Industrial Level and Limit Detection, Automotive and Off-Highway Sensing Node STM32G031J6M6TR STMicroelectronics Se usa en: Battery Threshold Monitoring, Automotive and Off-Highway Sensing Node STM32G031C8T6TR system controller taking the window fault output Se usa en: Window Comparator for Over/Undervoltage TS3702CDT commercial temperature grade variant for consumer devices Se usa en: Portable Instrument Sensor Conditioning, Battery Charger and Power Path Cutoff EFM32ZG222F8-B-QFP48R Silicon Labs Se usa en: Portable Instrument Sensor Conditioning STM32G474VET6TR STMicroelectronics Se usa en: Industrial Level and Limit Detection STM32G071C8T6TR STMicroelectronics Se usa en: Battery Charger and Power Path Cutoff
What is the TS3702ID and what does it do?
The STMicroelectronics TS3702ID is a micropower dual CMOS voltage comparator containing two independent general-purpose comparator channels in an 8-pin SOIC-8 package. According to the manufacturer datasheet, each channel consumes 9 uA typical, which is about twenty times less than the bipolar LM393 the device is designed to replace. Both channels share the same supply pins, so one IC can implement two threshold, window or level-detection functions while drawing roughly 18 uA of supply current.
How much supply current does the TS3702ID consume?
The TS3702ID consumes 9 uA typical per comparator, so a dual device in active operation draws about 18 uA from the supply. This micropower figure is the headline feature of the part: the manufacturer describes the TS3702 as drawing 20 times less current than a bipolar LM393. The low quiescent current makes the device well suited to battery-operated sensing nodes and portable instrumentation where every microamp of standing current shortens the service interval.
What is the supply voltage range of the TS3702ID?
The TS3702ID accepts a single supply from 2.7 V to 16 V or dual supplies from +/-1.35 V to +/-8 V. This wide operating window covers everything from a single 3 V coin cell rail through to industrial 12 V and 24 V-derived rails, where a regulator trims the rail below 16 V before the comparator sees it. Operating near the lower rail limit is supported because the input common-mode range includes ground, so the device still resolves signals close to 0 V.
Does the TS3702ID output need an external pull-up resistor?
No. The TS3702ID uses a push-pull CMOS output stage, so it actively sources and sinks output current and no external pull-up resistor is required. This is the main structural difference from open-collector comparators such as the LM393, which need an external resistor tied to the supply to hold the output high. Removing that resistor saves board area, lowers standby current and gives a valid CMOS logic high even at low supply voltages.
Is the TS3702ID pin-compatible with the LM393?
Yes. The manufacturer states that the TS3702 is pin-to-pin and functionally compatible with the bipolar LM393. The 8-pin SOIC-8 footprint therefore matches the familiar dual comparator arrangement, with two inputs plus the supply rails for channel one and channel two and one output per channel. The electrical differences are the CMOS push-pull output stage and the very low supply current, so existing LM393 boards can be converted without respinning the layout.
What is the input impedance of the TS3702ID?
The TS3702ID has a typical input impedance of 10^12 ohm, which is effectively infinite for practical calculations. This high impedance follows from the CMOS input stage and is paired with a typical input offset current of only 1 pA. In practice it means the comparator draws negligible current from the sensed node, so the divider that sets your threshold is barely loaded and the threshold voltage stays accurate as temperature and supply vary.
What is the response time of the TS3702ID comparator?
The TS3702ID has a typical response time of 2.3 us, giving fast output transitions relative to the slow, saturating bipolar outputs it replaces. A 2.3 us propagation delay is short enough for the device to sit directly in control loops such as battery cutoff, overvoltage protection and window fault detection, where the decision must be taken before the protected rail moves further out of tolerance. The 2 us class figure is quoted across the family in distributor documentation.
What is the operating temperature range of the TS3702ID?
The TS3702ID is rated for -40 C to +125 C operation, with the manufacturer marking code 3702I indicating the industrial grade. The wide range suits industrial control equipment, automotive-adjacent sensing and outdoor installations where the ambient swings widely. Note that the suffix matters: the TS3702CD variant carries a narrower commercial temperature rating, so specify the ID grade when the enclosure sees wide ambient variation.
Where can I download the TS3702ID datasheet PDF?
The manufacturer datasheet PDF for the TS3702 family is published by STMicroelectronics at https://www.st.com/resource/en/datasheet/ts3702.pdf and is the authoritative source for pinout, electrical characteristics and application circuits. Distributor-hosted copies of the same document are also available through the major catalogue listings. Download the manufacturer PDF and use the pin description table and the electrical characteristics table when assigning PCB tracks and setting switching thresholds.
Where can I find the TS3702ID pinout for the SOIC-8 package?
The TS3702ID pinout is shown in the STMicroelectronics TS3702 datasheet and follows the standard dual comparator SOIC-8 arrangement. The eight pins are, in order: OUT1, IN1-, IN1+, V-, IN2+, IN2-, OUT2 and V+. Use the pin description table in the manufacturer datasheet when assigning PCB tracks, and confirm the notch or dot orientation of the SOIC-8 package during assembly so that pin 1 is aligned with the package marker.
What is the best drop-in replacement for the TS3702ID?
The closest drop-in choices keep the same 8-pin SOIC-8 footprint: the STMicroelectronics TS3702CDT and TS3702IDT share the TS3702 die and differ only in temperature grade or packing, and the TS3702CD covers the commercial temperature grade. Because the TS3702 is documented as pin-to-pin compatible with the bipolar LM393, an LM393 in the same SOIC-8 package can also be substituted, with the caveat that the LM393 output is open-collector and needs a pull-up resistor.
TS3702ID vs TS3702CDT - which one should I choose for industrial use?
Choose the TS3702ID for industrial use because it is rated from -40 C to +125 C, while the TS3702CDT carries the narrower commercial temperature grade. Both devices use the same SOIC-8 package and the same TS3702 dual comparator architecture, so the two are pin-for-pin interchangeable on the board. The difference is purely the temperature qualification, which matters in cabinets, outdoor enclosures and machine rooms where ambient temperatures exceed the commercial limit.
When should I choose TS3702ID instead of TS3702IDT?
Choose the TS3702ID when you want the component delivered in tube or bulk packing for prototype work, small builds or manual assembly, and choose the TS3702IDT when you are running volume production with a pick-and-place line that consumes tape-and-reel packaging. Electrically the two are identical: same SOIC-8 package, same 9 uA per comparator, same 2.7 V to 16 V supply range. The suffix only encodes the delivery format, so decide on packing based on your assembly process.
Where can I buy the TS3702ID online and what is the price?
The TS3702ID is listed as an active, stocked comparator from STMicroelectronics and is available through the major electronic component distributors. Current unit pricing and bulk breaks change daily and are not published on this page, so use the Request a Quote form on this page to obtain a current quotation for the exact MPN, the quantity you need and the packing format. The same form covers single-unit samples, prototype quantities and production volume orders.
What is the lead time and stock status for the TS3702ID?
The TS3702ID is a long-established STMicroelectronics comparator, and the manufacturer continues to list the TS3702 family as an active product with distributor stock visible across many channels. Actual availability depends on the date code and packing option you need. Request the current lead time and stock confirmation through the Request a Quote form on this page, and state the quantity, the SOIC-8 packing preference and the delivery date you are working towards so the schedule can be confirmed accurately.
Can the LMV393 replace the TS3702ID?
The LMV393 is a micropower dual comparator in the same 8-pin SOIC-8 footprint with the same LM393-style pin arrangement, so it is a plausible substitute when low power and a small footprint matter most. Two points need checking before you commit: the LMV393 output stage is open-collector, so an external pull-up resistor must be added where the TS3702ID push-pull output does not need one, and the supply current and input offset figures differ. Verify both against the manufacturer datasheets for your operating conditions.
What are the key specifications of the TS3702ID that engineers should know?
The TS3702ID key specifications are: two general-purpose comparator channels, 9 uA typical supply current per comparator, a 10^12 ohm typical input impedance, 1 pA typical input offset current, a 2.3 us typical response time, a push-pull CMOS output that needs no pull-up resistor, a 2.7 V to 16 V single-supply range or +/-1.35 V to +/-8 V dual-supply range, and an operating temperature range of -40 C to +125 C in an 8-pin SOIC-8 package.

Datos de referencia de ingeniería para TS3702ID — comparación, orientación de diseño e información de cumplimiento.

Guía de selección

Choose the TS3702ID when your design needs two general-purpose threshold decisions from a single low-power chip: it runs at 9 uA per comparator, drives its output push-pull so no pull-up resistor is fitted, and carries the -40 C to +125 C industrial rating. Pick the TS3702IDT instead of the TS3702ID when you are building in volume and your assembler consumes tape and reel, and pick the TS3702CD or TS3702CDT when the enclosure stays inside the commercial temperature range and cost matters more than the industrial qualification. Consider the LM393 only for a respin of an existing bipolar design where a pull-up resistor is already present and the higher supply current is acceptable. The LMV393 is worth evaluating for micropower dual comparison in the same footprint, but remember that its open-collector output changes the output circuit and the pull-up resistor must be restored.

Comparación con alternativas

Parámetro Este producto TS3702CDT TS3702IDT TS3702CD LM393 LMV393
Package SOIC-8 (SO-8) SOIC-8 (SO-8) - same footprint SOIC-8 (SO-8) - same footprint SOIC-8 (SO-8) - same footprint SOIC-8 (SO-8) - same LM393 pinout SOIC-8 (SO-8) - same LM393 pinout
Brand STMicroelectronics STMicroelectronics STMicroelectronics STMicroelectronics Texas Instruments Texas Instruments
Number of Comparators 2 2 2 2 2 2
Output Type Push-pull CMOS (no pull-up resistor required) Push-pull CMOS Push-pull CMOS Push-pull CMOS Open collector, external pull-up required Open collector, external pull-up required

Diferenciadores clave

  • Push-pull CMOS output removes the external pull-up resistor (frente a LM393)
  • Roughly twenty times lower supply current per channel (frente a LM393)
  • Higher input impedance and lower offset current for threshold accuracy (frente a LMV393)
  • Industrial temperature grade in the same SOIC-8 footprint (frente a TS3702CDT)

Notas de diseño

Do not add an external pull-up resistor to the TS3702ID output. The device uses a push-pull CMOS output stage, so an added pull-up simply wastes current and, in a push-pull stage, can create contention when the output drives low. Boards copied from an LM393 design may already carry that resistor; check the schematic before reusing an LM393 layout and confirm the output node in the TS3702 datasheet pin description table. If a pull-up must stay in the circuit for an open-collector-style downstream device, make sure the downstream input is high impedance.

Estimated: with both channels active at 9 uA each, the TS3702ID draws about 18 uA from the supply, so a 3 V cell with a 1000 uF reservoir would be depleted in roughly (3 V x 1000 uF)/(18 uA) = 167 hours if no other load exists. Use that figure as a sizing starting point, then add the load current of the logic that the comparator enables. Keep the supply decoupling close to pins 8 and 4, since a supply that sags as the output switches can shift the threshold during a transition.

The 10^12 ohm input impedance and 1 pA typical input offset current mean the threshold network must be designed for thermal stability rather than bias error. Keep the divider resistors at or below 1 M ohm so that leakage from board contamination, humidity and flux residue does not dominate the 1 pA bias, and place a 100 nF ceramic capacitor directly at the reference input to reject supply ripple that would otherwise modulate the trip point. Keep the sensor trace short and away from switching nodes, since the 2.3 us response time means fast transients are reproduced at the output.

Use the pin description table in the STMicroelectronics TS3702 datasheet to assign tracks on the 8-pin SOIC-8 footprint: OUT1, IN1-, IN1+, V-, IN2+, IN2-, OUT2 and V+. Place the two input networks so that each comparator's inverting and non-inverting pins are not adjacent to noisy switching pins of neighbouring circuitry, tie V- to the ground plane with a short direct connection, and route V+ through a local 100 nF capacitor to the plane. Because the part is pin-to-pin compatible with the LM393, keeping this layout discipline also makes an LM393-based respin possible without a board change.

Información de cumplimiento

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Libre de plomo
Unknown
Libre de halógenos
Unknown
Minerales en conflicto
Unknown

The manufacturer datasheet and distributor listings confirm the device is a general-purpose industrial comparator with a -40 C to +125 C rating. Explicit RoHS, REACH, lead-free and halogen-free declarations were not identified for this exact MPN, so they are reported as unknown; check the STMicroelectronics product page for the current compliance statements before releasing a regulated design.

Datos verificados el: 2026-11-16 — datos verificados y seleccionados por el equipo de ingeniería de componentes de XAIPART

Búsquedas relacionadas

TS3702ID TS3702ID datasheet TS3702ID datasheet pdf TS3702ID pinout TS3702ID SOIC-8 comparator TS3702ID vs TS3702CDT TS3702ID equivalent TS3702ID drop-in replacement STMicroelectronics TS3702ID micropower dual CMOS comparator 9uA push-pull comparator no pull-up resistor TS3702ID battery threshold monitor TS3702ID price and stock TS3702ID vs LM393

Componentes & términos relacionados

STMicroelectronics TS3702ID TS3702 TS3702CDT TS3702IDT TS3702CD LM393 LMV393 voltage comparator dual comparator general purpose comparator analog IC amplifier and comparator IC signal conditioning push-pull CMOS output open-collector output LM393 pin compatibility CMOS process input impedance input offset current supply current common-mode voltage range propagation delay SOIC-8 SO-8 package surface mount RoHS battery monitoring
RFQ de presupuesto rápido
Complete los detalles — nuestro equipo de ventas responderá en un plazo de 24 horas
Número de pieza Fabricante Encapsulado QTY Precio objetivo Total
✓
¡Presupuesto enviado!

Responderemos a su correo electrónico en un plazo de 24 horas

1
RFQ enviado
2
Presupuesto recibido
3
Pedido realizado
4
Pago
5
Enviado
6
Entregado
Ver detalles del RFQ