TS556IDT - Dual CMOS Timer, 2.7MHz, SOIC-14 | STMicroelectronics
部品番号: TS556IDT ✓ 生産中TS556IDT 概要
A 555 timer is a programmable time-delay and oscillator building block within the broader clock and timing IC category. Each TS556 timer section contains a voltage reference, comparators, a flip-flop, discharge transistor, and an output stage. The timing interval is set by external resistors and capacitors connected to the RC timing pins. Typical uses include delayed switching, pulse stretching, debounce circuits, lamp flashers, simple oscillators, and frequency dividers.
Key characteristics include a 2.7 MHz maximum astable frequency, a wide 2 V to 16 V operating supply range, and low power consumption. The manufacturer identifies the TS556 as a dual CMOS timer with typical supply current of 220 uA at VCC = 5 V, compared with approximately 6 mA for the NE556(a) bipolar family. The available technical description also identifies the TS556 as pin-to-pin and functionally compatible with bipolar NE556(a) devices.
The dual configuration allows two independent timing channels in one package, reducing component count and board area when an application needs simultaneous or complementary timing functions. The TS556IDT is suitable for industrial control, sensor interfaces, pulse generation, low-power instrumentation, embedded timing modules, and general-purpose oscillator circuits. Its SOIC-14 package supports conventional surface-mount assembly while retaining the familiar dual 555 interface.
When designing a replacement board, use the manufacturer pin-description table to preserve trigger, threshold, control-voltage, discharge, and output connections. Confirm the intended mode of operation and external RC network before changing timing components. The 2.7 MHz figure is a maximum astable-frequency capability, and actual operating frequency depends on resistor and capacitor values, load conditions, supply voltage, and timing tolerances. For systems requiring exact timing accuracy, evaluate the minimum and maximum RC values and the propagation behavior of the output stage over the intended voltage and temperature ranges.
This page combines the TS556IDT datasheet information, package details, timing-use context, and practical replacement guidance to support faster component selection and PCB-level integration.
ドロップイン代替品: TS556IDT — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: TS556IDT (同一形状・フットプリント) — 相違点: Operating Modes, Package.
TS556IDTTR
✅ ドロップイン📋 参考代替品(カタログ未掲載)
TLC556IDR
✅ ドロップイン📋 参考代替品(カタログ未掲載)
TS556IDT 仕様
| Timer Configuration | Dual 555-type timer |
| Maximum Astable Frequency | 2.7 MHz |
| Supply Voltage Range | 2 V to 16 V |
| Typical Supply Current | 220 uA at VCC = 5 V |
| Low-Power Supply Current | 180 uA typical at VCC = 3 V |
| NE556 Typical Supply Current | 6 mA at VCC = 5 V |
| Operating Modes | Astable and monostable |
| Technology | CMOS |
| パッケージ | 14-pin SOIC |
| 実装タイプ | Surface Mount |
| Pin Compatibility | Pin-to-pin and functionally compatible with bipolar NE556(a) |
| RoHS ステータス | RoHS compliant |
| Lead-Free Status | Lead-free |
| Timer Sections | 2 independent channels |
TS556IDT ピン構成
| ピン 1 | TRIGGER 1 — Trigger input for timer section 1 |
| ピン 2 | OUTPUT 1 — Timer output for section 1 |
| ピン 3 | OUTPUT 2 — Timer output for section 2 |
| ピン 4 | RESET 1 — Reset input for timer section 1 |
| ピン 5 | CONTROL VOLTAGE 1 — Control-voltage input for timer section 1 |
| ピン 6 | THRESHOLD 1 — Threshold input for timer section 1 |
| ピン 7 | DISCHARGE 1 — Discharge output for timer section 1 |
| ピン 8 | TRIGGER 2 — Trigger input for timer section 2 |
| ピン 9 | OUTPUT 2 — Timer output for section 2 |
| ピン 10 | RESET 2 — Reset input for timer section 2 |
| ピン 11 | CONTROL VOLTAGE 2 — Control-voltage input for timer section 2 |
| ピン 12 | THRESHOLD 2 — Threshold input for timer section 2 |
| ピン 13 | DISCHARGE 2 — Discharge output for timer section 2 |
| ピン 14 | VCC — Positive supply voltage |
| ピン 15 | GND — Ground reference |
主な用途
TS556IDT の用途: 6 件s: Low-Power Astable Oscillator, Monostable Pulse Generator, Delay and Debounce Circuit, Industrial Control Pulse Module, Frequency Divider and Tone Generator, Battery-Powered Instrumentation.
Low-Power Astable Oscillator
The TS556IDT is well suited to a low-power astable oscillator because each channel can generate a repetitive waveform using external resistors and capacitors. Its dual CMOS timer architecture supports supply voltages from 2 V to 16 V, while typical consumption is listed as 220 uA at 5 V. The 2.7 MHz maximum astable frequency provides substantial timing range, from low-frequency clock-like waveforms to higher-frequency signal generation. Design the RC network around the manufacturer’s recommended component limits and verify frequency tolerance, duty cycle, and output loading over the intended voltage and temperature range.
おすすめ
Monostable Pulse Generator
A TS556IDT channel can be configured as a monostable timer to produce a fixed-duration pulse after a trigger event. The internal comparator, flip-flop, discharge transistor, and output stage implement the timing sequence, while external resistors and capacitors establish the pulse interval. The 2 V minimum supply allows operation in compact low-voltage systems, and the dual arrangement permits a second independent pulse function. When substituting into an existing circuit, preserve trigger and threshold levels and validate output pulse width against the intended minimum and maximum RC values.
おすすめ
Delay and Debounce Circuit
The TS556IDT can implement delay and contact-debounce functions in sensor, control-panel, and switch-interface circuits. A trigger starts the timing interval, and the timer output changes state after the programmed RC delay. Low CMOS supply current is valuable in battery-operated equipment, particularly when the timer is active only intermittently. Use the dual channels when separate delays or a complementary output relationship is needed, and check the output rise and fall timing at the logic family connected to the timer.
おすすめ
Industrial Control Pulse Module
In industrial control equipment, the TS556IDT can generate repeatable timing pulses for actuator sequencing, watchdog-like delays, or periodic control events. Its 2 V to 16 V supply range supports multiple embedded control architectures, while the dual timer channels can reduce component count by combining two timing functions in one 14-pin SOIC. For industrial deployments, check temperature limits, output current, supply-current spikes during transitions, and timing tolerances before finalizing the external component values and protection strategy.
おすすめ
Frequency Divider and Tone Generator
The TS556IDT can generate a periodic clock and divide that frequency into a lower useful timing signal for counters, display systems, or sequencing logic. Its maximum astable frequency of 2.7 MHz gives designers headroom above many low-speed timing requirements, while the 2 V to 16 V operating range supports different logic environments. Verify the output duty cycle and propagation behavior at the target frequency, and use the second timer channel when a separate delay, tone, or modulation function is required.
おすすめ
Battery-Powered Instrumentation
The TS556IDT is appropriate for portable measurement or instrumentation modules where continuous timer operation must not dominate the power budget. The manufacturer lists typical supply current of 220 uA at 5 V for the TS556, materially below the 6 mA figure cited for NE556(a), and the timer operates down to 2 V. Use the device for low-duty-cycle sample timing, delayed acquisition, or periodic sensor stimulation. Confirm battery voltage range, leakage through external timing components, and the idle current of the complete instrument rather than the timer alone.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: TS556IDT — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | TS556IDTTR | TLC556IDR |
|---|---|---|---|
| Package | 14-pin SOIC | 14-pin SOIC - same | 14-pin SOIC - same |
| Brand | STMicroelectronics | STMicroelectronics | Texas Instruments |
| Timer Configuration | Dual 555-type timer | Dual CMOS timer | Dual timer |
| Maximum Astable Frequency | 2.7 MHz | 2.7 MHz | 2.1 MHz |
| Minimum Supply Voltage | 2 V | 2 V | 2 V |
| Technology | CMOS | CMOS | CMOS |
| Packing | Tape and reel | Tape and reel | Tape and reel |
主な差別化要因
- Higher specified maximum astable frequency (vs TLC556IDR)
- Lower typical supply current at 5 V (vs NE556)
- Same-family electrical identity (vs TS556IDTTR)
設計ノート
Place the external timing resistor and capacitor close to the relevant DISCHARGE, THRESHOLD, and TRIGGER pins to limit parasitic capacitance and resistance. Keep the two timer channels physically separated where one channel drives a sensitive analog or timing input. Confirm the package footprint and pin-1 orientation against the manufacturer drawing before layout release.
Route the supply and ground pins directly to the device and provide local high-frequency bypass capacitance. Although the TS556 has low typical supply current, output transitions can create supply-current spikes, particularly when driving capacitive loads or long PCB traces. Decouple each timer section according to the manufacturer application guidance and avoid routing timing outputs near sensitive high-impedance nodes.
Do not treat the 2.7 MHz maximum as an unconditional operating point. The actual astable frequency depends on the RC network, supply voltage, temperature, and load. Before using TS556IDT as a drop-in substitute for a bipolar NE556, verify pin connectivity, output polarity, timing tolerance, output-current capability, and maximum frequency. The TS556 is described as NE556(a)-compatible, but the exact circuit still requires validation.
The trigger and threshold inputs are timing-sensitive nodes. Avoid long traces, unnecessary vias, and capacitive loading near these pins, especially at higher astable frequencies. If an external signal must drive TRIGGER, use a source impedance and edge rate compatible with the device input and ground-return current through the same reference network. Check pulse-width behavior and output timing over the intended supply range.
コンプライアンス情報
The verified comparison material identifies TS556IDTTR as RoHS compliant with an Ecopack3 designation. Other compliance attributes were not established for the exact TS556IDT orderable part.