TS944IDT - Quad Micropower R-R Op Amp | STMicroelectronics
MPN: TS944IDT ✓ نشطTS944IDT نظرة عامة
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its two input terminals. The TS94x family belongs to the operational-amplifier hierarchy, which includes instrumentation amplifiers, buffer amplifiers, and general-purpose amplifiers. Rail-to-rail output capability allows the output voltage to approach the supply rails more closely than a conventional amplifier, improving output range in low-voltage systems where signal headroom is limited.
The TS944IDT combines four rail-to-rail-output amplifiers, CMOS inputs, micropower consumption, and a 2.5 V to 10 V supply range. Its 10 kHz gain-bandwidth product favors low-frequency amplification rather than high-speed signal processing. The 1.2 µA operating current is particularly useful for battery-operated equipment, portable sensors, and low-duty-cycle monitoring systems where each milliamp of supply current can shorten operating time.
According to the STMicroelectronics TS94x datasheet, the TS944IDT provides four amplifier circuits in a 14-pin small-outline package. CMOS input transistors support low-bias operation, while the rail-to-rail output stage increases usable output swing. The combination of four independent channels and low power consumption allows a compact design to replace several discrete single amplifiers while reducing board area and the number of required supply connections.
Typical applications include low-frequency sensor conditioning, battery-powered instrumentation, portable measurement systems, industrial monitoring, and low-current feedback networks. The TS944IDT is best suited to signals whose bandwidth does not require the substantially higher gain-bandwidth product of a general-purpose precision amplifier.
Designers should verify that the required closed-loop gain, output load, input common-mode range, and noise performance fit the application. Decoupling capacitors should be placed close to the supply pins, and the unused amplifier channels should be configured according to the manufacturer datasheet rather than left without a defined operating state.
This page combines the TS944IDT technical characteristics, verified sourcing information, drop-in alternatives, and application guidance to support component selection, PCB planning, and low-power analog design.
بدائل مباشرة لـ TS944IDT — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
الطرازات في هذه السلسلة
طرازات من نفس السلسلة متوافقة تمامًا مع TS944IDT (نفس عامل الشكل والبصمة) — يختلف في Package, Amplifier Type, Gain-Bandwidth Product, Number of Circuits, AEC-Q100 Qualification.
TS934IDT
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منهاتواصل لمعرفة السعر
عرض ورقة البيانات ←TS974IDT
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منهاتواصل لمعرفة السعر
عرض ورقة البيانات ←TS924IPT
✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منهاتواصل لمعرفة السعر
عرض ورقة البيانات ←TS944IDT الحدود القصوى والخصائص الكهربائية
| Amplifier Count | 4 circuits |
| Device Type | Quad operational amplifier |
| Supply Voltage Range | 2.5 V to 10 V |
| نطاق درجة حرارة التشغيل | -40°C to +85°C |
| تيار السكون | 1.2 µA |
| Gain-Bandwidth Product | 10 kHz |
| Output Swing | Rail-to-rail |
| Input Transistor Type | CMOS |
| العلبة | 14-pin SO |
| نوع التركيب | Surface mount |
| Output Offset Voltage | 4.5 mV maximum |
| تيار التغذية | 1.2 µA per amplifier |
| حالة RoHS | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | not_applicable |
دليل تكوين أطراف TS944IDT 14-pin so
تكوين الأطراف لـ TS944IDT (حزمة 14-pin so). يتميز هذا المكوّن التناظري بأطراف الإدخال والإخراج وإمداد الطاقة. راجع ورقة بيانات الشركة المصنعة لتكوينات طرف إلغاء الإزاحة والتعويض والتمكين. مثالي لدوائر تكييف الإشارة والمضخمات.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ TS944IDT.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
TS944IDT مناسب لـ 6 التطبيقs: Battery-Powered Sensor Conditioning, Portable Industrial Instrumentation, Low-Power Data Acquisition, Portable Medical Monitoring, IoT Environmental Sensor Hub, Low-Power Feedback and Control Loops.
Battery-Powered Sensor Conditioning
The TS944IDT is well suited to battery-powered sensor conditioning because it combines four amplifier channels with a 1.2 µA supply current and a 2.5 V minimum supply voltage. Each rail-to-rail-output amplifier can condition a low-frequency sensor signal while the compact 14-pin SO package reduces board area. The approximately 10 kHz gain-bandwidth product supports slow sensor signals, such as temperature, pressure, or electrochemical measurements, but it is not intended for high-speed waveforms. The design should include input protection appropriate to the sensor and verify the amplifier’s common-mode range over the complete measurement range.
موصى به
Portable Industrial Instrumentation
Portable industrial instrumentation can use the TS944IDT to amplify several low-frequency channels without adding four separate amplifier packages. Its 2.5 V to 10 V operating range supports compact electronic systems, while the -40°C to +85°C specification covers a broad range of industrial ambient conditions. The four rail-to-rail-output channels are useful for transducer signals where more usable output range is needed at low supply voltage. Engineers should confirm input common-mode limits, offset accuracy, noise, and output drive against the instrumentation specification. Protection, calibration, and isolation requirements should be addressed separately from the amplifier selection.
موصى به
Low-Power Data Acquisition
The TS944IDT can serve as the front-end amplifier in a compact, low-power data-acquisition system that samples slow analog inputs. Four independent channels reduce the component count compared with separate single amplifiers, while 1.2 µA supply current supports longer operating time from limited energy sources. Its 10 kHz gain-bandwidth product is adequate for temperature, level, and position measurements but limits fast transient fidelity. The system designer should account for input settling, channel-to-channel behavior, sensor-grounding strategy, and the available voltage headroom. An external low-power ADC can then acquire the conditioned outputs.
موصى به
Portable Medical Monitoring
The TS944IDT may be used in low-frequency medical monitoring modules when four low-power analog channels are required within a compact package. Its micropower operation can reduce the load on a small battery, while rail-to-rail output swing improves signal utilization at low supply voltages. The 10 kHz bandwidth suits slowly varying physiological or biochemical signals rather than high-bandwidth diagnostic waveforms. Medical designs must independently validate leakage, isolation, noise, accuracy, and applicable regulatory requirements; the amplifier’s general-purpose status does not imply medical certification. Input protection and patient-safety isolation should be implemented outside the device.
موصى به
IoT Environmental Sensor Hub
An IoT environmental sensor hub can use the TS944IDT to condition several low-bandwidth sensor channels while maintaining low standby consumption. The device supports 2.5 V to 10 V operation, which accommodates common low-energy system rails, and its four channels help limit hub size. Rail-to-rail output swing is useful when measurements must occupy much of a low-voltage signal range. The 1.2 µA operating current is attractive for duty-cycled devices, though the complete circuit will consume more power when sensors and communications are active. Firmware and analog design should avoid relying on this amplifier for high-frequency radio or switching signals.
موصى به
Low-Power Feedback and Control Loops
The TS944IDT can implement gain, filtering, and feedback functions in low-power control systems where the loop bandwidth remains well below the amplifier’s 10 kHz gain-bandwidth product. Four channels allow separate error, reference, actuator, or monitoring paths within one package. The rail-to-rail output helps maximize control range from a 2.5 V to 10 V supply, while the low 1.2 µA supply current supports compact battery-powered loops. Stable operation depends on suitable phase margin, source-and-load impedances, and output-capacitance selection, none of which should be assumed from the headline bandwidth alone. Verify stability with the complete feedback network.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ TS944IDT — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج | TS934IDT | TS974IDT | TS924IPT |
|---|---|---|---|---|
| Package | SOIC-14 | SOIC-14 | SOIC-14 | SOIC-14 |
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
أبرز الفروقات
- Combines four micropower amplifier channels in one package (مقابلTS934IDT)
- Designed for an exceptionally low 2.5 V minimum supply (مقابلTS974IDT)
- Rail-to-rail output improves low-voltage signal range (مقابلTS924IPT)
ملاحظات التصميم
Place the supply-decoupling capacitors directly beside the TS944IDT power and ground pins, and keep those traces short. Use the STMicroelectronics datasheet layout recommendations to determine the required capacitance and connection geometry. A compact ground path beneath and around the device helps reduce supply impedance and coupling between adjacent analog channels. Confirm that the exposed package and copper treatment match the selected 14-pin SO assembly.
Do not treat the 10 kHz gain-bandwidth product as suitable for high-speed signal conditioning. For slow sensor signals, check the closed-loop gain against the frequency range of interest, and calculate the resulting bandwidth rather than relying on the gain-bandwidth value alone. Also verify the input common-mode range, output swing under load, and maximum output current before finalizing the gain and bias network.
Because the TS944IDT contains four amplifiers in one package, sensitive inputs and outputs should be routed to avoid parallel long traces that can couple noise between channels. Ground each input reference close to its source, keep high-impedance feedback networks compact, and separate analog signal routes from switching or digital clock paths. When one channel is unused, configure it according to the manufacturer datasheet rather than allowing an undefined input condition.
The headline 1.2 µA supply current applies to the amplifier operating condition described by STMicroelectronics; complete battery-life calculations must include sensor current, pull resistors, leakage, and external circuitry. For duty-cycled systems, ensure the TS944IDT supply can be switched without creating input overvoltage on non-powered channels. Review the power-up sequence and input tolerances before using the device with partially powered sensors.
معلومات الامتثال
No specific RoHS, REACH, halogen-free, lead-free, conflict-minerals, or automotive-qualification statement appears in the cited product information. The general-purpose operational-amplifier category is not treated as AEC-Q100 qualification.