WM8750LSEFL - Stereo Audio Codec with Speaker | Wolfson
MPN: WM8750LSEFL ✗ انتهى عمره الإنتاجيWM8750LSEFL نظرة عامة
An audio codec is an integrated circuit that converts between digital audio data and analog microphone, headphone, and speaker signals. In the signal-chain hierarchy, the WM8750LSEFL is an audio codec, a mixed-signal interface IC, and a power-management-assisted audio output device. Its integrated converter, microphone interface, headphone amplifier, and speaker driver reduce the number of external components required in portable playback, recording, and communication equipment.
The device supports a complete stereo or mono microphone interface with programmable automatic level control and a noise gate. The 98 dB A-weighted DAC SNR and -95 dB total harmonic distortion at 48 kHz and 3.3 V support low-noise digital-to-analog playback. Its 95 dB A-weighted ADC SNR and -90 dB total harmonic distortion at the same operating condition provide symmetrical recording performance when low distortion is important.
Output integration provides practical advantages for portable systems. The mono bridge-tied-load speaker driver can deliver 400 mW without requiring a separate power amplifier, while the integrated headphone driver can supply more than 40 mW into a 16-ohm load at 3.3 V. These functions are controlled through the codec interface, allowing software-managed audio routing and gain configuration.
Typical uses include portable media players, personal audio devices, smart-home audio endpoints, headset electronics, compact recording products, and battery-powered communication equipment. Its integrated speaker and headphone paths are especially useful where PCB area, component count, and power-management complexity must be controlled without sacrificing essential playback functions.
When laying out a circuit, use the manufacturer pin-description table and application schematic to assign analog, digital, and power connections. Keep microphone inputs and headphone outputs away from high-speed digital traces, provide the recommended decoupling capacitors at their supply pins, and verify speaker impedance and thermal conditions against the datasheet limits.
This product record combines the WM8750LSEFL feature information with practical guidance on audio performance, layout, thermal considerations, component pairing, and replacement selection. It is structured to help engineers identify the correct codec, compare its integrated functions, and plan a robust portable-audio implementation before layout release.
بدائل مباشرة لـ WM8750LSEFL — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
لا تتوفر بدائل متوافقة تمامًا لهذا المنتج.
اطلب بدائلWM8750LSEFL المواصفات
| DAC Signal-to-Noise Ratio | 98 dB A-weighted |
| DAC Total Harmonic Distortion | -95 dB at 48 kHz and 3.3 V |
| ADC Signal-to-Noise Ratio | 95 dB A-weighted |
| ADC Total Harmonic Distortion | -90 dB at 48 kHz and 3.3 V |
| Speaker Output Power | 400 mW |
| Speaker Output Topology | Mono BTL |
| Headphone Output Power | Greater than 40 mW into 16 ohms at 3.3 V |
| Microphone Interface | Complete stereo or mono interface |
| Automatic Level Control | Programmable |
| Noise Gate | Programmable |
| Audio Converter Type | Stereo ADC and stereo DAC |
| Typical Operating Supply | 3.3 V |
| معدل أخذ العينات | 48 kHz reference condition |
دليل تكوين أطراف WM8750LSEFL standard
تكوين الأطراف لـ WM8750LSEFL (حزمة standard). يتم تعريف ترقيم الأطراف والوظائف ومخططات التوصيل في ورقة البيانات الفنية من الشركة المصنعة. راجعها للحصول على البصمة الدقيقة وإرشادات اللحام.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ WM8750LSEFL.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
WM8750LSEFL مناسب لـ 6 التطبيقs: Portable Media Player, Headset and Headphone Electronics, Smart-Home Audio Endpoint, Portable Recording Product, Battery-Powered Communication Device, Compact Audio Interface.
Portable Media Player
The WM8750LSEFL fits portable media players that combine digital playback, microphone recording, headphone output, and a small internal speaker. According to the Wolfson Microelectronics datasheet, the codec delivers a 98 dB A-weighted DAC SNR and -95 dB DAC distortion at 48 kHz and 3.3 V, providing a low-noise playback path without a separate output codec. Its integrated headphone driver can deliver more than 40 mW into 16 ohms, while the 400 mW mono BTL stage can drive a compact speaker. The tradeoff is that the integrated output path is optimized for portable, moderate-power loads rather than high-impedance studio headphones or multi-speaker systems.
موصى به
Headset and Headphone Electronics
The WM8750LSEFL is suitable for headset electronics requiring digital voice capture and low-power headphone playback in one device. Its stereo or mono microphone interface, programmable automatic level control, and programmable noise gate support portable speech capture, while the headphone stage provides more than 40 mW into a 16-ohm load at 3.3 V. The ADC provides 95 dB A-weighted SNR and -90 dB distortion at 48 kHz and 3.3 V. This integration reduces the number of analog output blocks in compact products, although engineers must still check microphone biasing, headset impedance, plug detection, and acoustic limits against the manufacturer application circuit.
موصى به
Smart-Home Audio Endpoint
The WM8750LSEFL can support a compact smart-home audio endpoint that plays local notifications or streamed sound while accepting voice input. Its integrated 400 mW mono BTL speaker driver suits a small enclosure-mounted transducer, and the programmable microphone path can use automatic level control and noise gating for speech capture. Converter performance includes 98 dB A-weighted DAC SNR and 95 dB A-weighted ADC SNR at the documented operating conditions. A design should provide clean 3.3 V power, separate analog and digital grounding where appropriate, and protection appropriate to the speaker wiring and physical installation.
موصى به
Portable Recording Product
The WM8750LSEFL fits portable stereo-recording products that need integrated microphone conditioning, high-resolution conversion, monitoring, and speaker playback. The stereo or mono microphone interface includes programmable automatic level control and a programmable noise gate, while the ADC delivers 95 dB A-weighted SNR and -90 dB total harmonic distortion at 48 kHz and 3.3 V. The same device can provide headphone monitoring above 40 mW into 16 ohms and a 400 mW mono BTL speaker path for playback. Input selection, gain range, sampling rate, clocking, and record-path filtering must be configured from the datasheet and register description before production testing.
موصى به
Battery-Powered Communication Device
The WM8750LSEFL is appropriate for battery-powered communication equipment requiring voice capture, local monitoring, and a compact speaker. Its 3.3 V operating condition and integrated headphone and BTL speaker stages reduce the board area associated with separate output amplifiers. The microphone interface supports programmable automatic level control and noise gating, which can help maintain usable signal levels in changing acoustic conditions. The 400 mW BTL specification describes the maximum documented speaker output condition, so battery current, speaker impedance, and enclosure temperature should be evaluated before operation at the upper output limit.
موصى به
Compact Audio Interface
The WM8750LSEFL can serve as the central converter in a compact audio interface when both analog recording and playback are required. The stereo ADC and DAC provide 95 dB and 98 dB A-weighted SNR, respectively, at the documented 48 kHz and 3.3 V reference conditions. Programmable microphone-level and noise-gate functions support input conditioning, while integrated headphone and speaker outputs reduce external amplifier count. Designers should treat these headline figures as component-level performance: full-scale input selection, clock configuration, analog layout, grounding, and the external microphone and output networks determine the finished interface performance.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ WM8750LSEFL — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج |
|---|---|
| Device Type | Stereo audio codec |
| Brand | Wolfson Microelectronics |
| DAC SNR | 98 dB A-weighted |
| DAC Total Harmonic Distortion | -95 dB at 48 kHz and 3.3 V |
| ADC SNR | 95 dB A-weighted |
| ADC Total Harmonic Distortion | -90 dB at 48 kHz and 3.3 V |
| Speaker Output | 400 mW mono BTL |
| Headphone Output | Greater than 40 mW into 16 ohms at 3.3 V |
| Microphone Interface | Stereo or mono with programmable ALC and noise gate |
ملاحظات التصميم
Separate the microphone, headphone, and speaker routing from high-speed digital audio traces. Use the manufacturer application schematic to identify analog input and output networks, and place their associated passive components close to the corresponding pins. Keep the BTL speaker connections away from sensitive microphone inputs because the bridge-tied-load output uses both output terminals as active signals. Verify the ground-return arrangement on the manufacturer reference layout before releasing PCB artwork.
Follow the datasheet requirements for analog and digital supply connections and decoupling. The documented 98 dB DAC SNR and 95 dB ADC SNR are measured at 3.3 V, making supply integrity especially relevant to the converter performance. Place low-ESR decoupling capacitors at the appropriate supply pins, keep their current loops compact, and avoid routing supply and return paths through noisy speaker-driver return currents. Confirm the actual noise and ripple tolerance of each rail during system testing.
Estimated: speaker power dissipation is approximately 0.4 W when the integrated BTL stage operates at its documented 400 mW output condition. This estimate uses the documented 400 mW output and excludes codec overhead and efficiency losses; actual device dissipation also depends on load, supply voltage, signal duty cycle, and ambient temperature. Verify the maximum operating case at the highest expected speaker impedance, because a lower impedance can increase output current and thermal stress.
Do not substitute a generic stereo codec solely because its DAC and ADC headline specifications appear similar. Drop-in replacement requires matching package pins, supply rails, clocking, digital audio format, control interface, clocking, and software register behavior. The BTL speaker output also requires the correct bridge connection and must not be treated as a conventional ground-referenced amplifier output. Review the complete manufacturer pinout and register map during any replacement or second-source evaluation.
معلومات الامتثال
Compliance status is not stated in the manufacturer feature information available for this part. The lead-free suffix must not be interpreted as a complete RoHS, REACH, halogen-free, or conflict-minerals declaration.