উপশ্রেণী

পণ্য (44,000+)

TSA7887ARMZ - 12-Bit 125ksps 2-Ch SAR ADC | Silicon Labs
TSA7887ARMZ

TSA7887ARMZ - 12-Bit 125ksps 2-Ch SAR ADC | Silicon Labs

The Silicon Labs TSA7887ARMZ is a 12-bit, 125 ksps, 2-channel successive-approximation register (SAR) analog-to-digital converter with a serial SPI/QSPI/MICROWIRE-compatible output, an internal 2.5V reference, and an 8-pin MSOP package. Originally developed by Touchstone Semiconductor (later acquired and second-sourced by Silicon Labs), the device operates from a 2.7V to 5.25V analog supply and is targeted at low-power instrumentation that demands sub-microamp standby current and 12-bit true conversion precision. An SAR ADC (successive-approximation-register analog-to-digital converter) is a type of data converter that uses a binary-search algorithm against an internal capacitive DAC to resolve an analog input one bit per conversion clock cycle. It belongs to the broad family of analog-to-digital converters (ADCs), which itself is part of the data-converter hierarchy inside mixed-signal and signal-chain integrated circuits. The SAR architecture is favored over delta-sigma and pipeline ADCs when low-latency deterministic conversion, small package size, and moderate sample rates (tens to hundreds of ksps) are required, particularly in multiplexed multi-channel systems. Key features of the TSA7887ARMZ include an internal 2.5V reference (selectable externally via the REF pin), a 2-channel analog input multiplexer, true 12-bit performance with no missing codes, a 125 ksps maximum throughput, low power dissipation (typically under 2.5 mW at 3V/100 ksps), and automatic power-down between conversions that drops supply current below 1 microampere. The device uses an external clock for the serial interface and supports both unipolar single-ended and pseudo-differential input configurations. The device leverages a charge-redistribution SAR core with input transient suppression and an automatic input common-mode settling window, which makes it tolerant of source-impedance variations when channels are switched. Combined with the internal precision reference, this means the TSA7887ARMZ can replace an external ADC + reference + op-amp buffer chain in many space-constrained designs. Typical applications include portable and battery-powered data loggers, industrial process-control sensor front-ends (thermocouple, RTD, strain-gauge bridges), handheld instrumentation, and multiplexed 4-20 mA loop monitors. Designers also use it in optical sensor modules and consumer battery chargers where periodic current/voltage telemetry is required. When designing with this part, size the input RC network and reference bypass capacitors per the datasheet's application circuit - inadequate decoupling is the most common cause of last-2-LSB noise and gain drift in SAR circuits. Consider the MAX1276CTC+ from Maxim's family as a drop-in 8-pin MSOP alternative if higher conversion speed is needed. This page synthesizes distributor pricing, drop-in MSOP-8 alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ যোগাযোগ
TSA7887ARMZ-REEL - 12-bit 125ksps 2-ch SAR ADC | Silicon Labs
TSA7887ARMZ-REEL

TSA7887ARMZ-REEL - 12-bit 125ksps 2-ch SAR ADC | Silicon Labs

The Silicon Labs TSA7887ARMZ-REEL is a 12-bit, 125 ksps, 2-channel successive-approximation-register (SAR) analog-to-digital converter housed in an 8-pin MSOP package with a single +2.7V to +5.25V supply. The 'RMZ' suffix indicates the MSOP-8 (RM) tape-and-reel (REEL) packaging variant. Originally designed by Touchstone Semiconductor as a pin-compatible second source for the ADI AD7887, the part features an internal +2.5V reference, internal wideband track-and-hold, and serial I/O compatible with SPI, MICROWIRE, QSPI, and DSP ports. Typical supply current is 0.85 mA at full throughput, qualifying the part as a micropower converter for battery and loop-powered systems. A SAR ADC is a successive-approximation-register analog-to-digital converter, a converter topology that uses a binary-search algorithm and a capacitive charge-redistribution DAC to resolve each conversion in N clock cycles for an N-bit result. SAR converters sit in the data-converter hierarchy between flash converters (fastest, lowest resolution) and sigma-delta converters (highest resolution, slowest). They are valued for deterministic latency, low power consumption, and the ability to drive them directly from a microcontroller or DSP serial port without an external reference or high-speed clock. Key features include a 500 ns input track-and-hold acquisition time, an internal +2.5V reference that eliminates external reference components, and a single-ended analog input structure that supports one or two channels multiplexed to the ADC core. Throughput scales with the external serial clock up to 125 ksps at 2 MHz SCLK. The wide supply range allows direct interfacing to 3.3V and 5V microcontrollers, while the small MSOP-8 footprint suits space-constrained sensor readouts and portable instrumentation. Typical applications include transducer and sensor signal conditioning, battery-powered data loggers, industrial process control loops with 4-20 mA interfaces, and portable medical or instrumentation front-ends. The combination of low power, internal reference, and small footprint also suits loop-powered 4-20 mA smart transmitters where every milliwatt and square millimeter matters. When designing with this device, ensure the analog input stays within the input common-mode range specified by the supply, and add a small RC anti-alias filter on each input to limit out-of-band noise folding into the conversion result.

RFQ যোগাযোগ
TSA7887ARZ - 12-bit 125ksps 2-ch SAR ADC | Silicon Labs SOIC-8
TSA7887ARZ

TSA7887ARZ - 12-bit 125ksps 2-ch SAR ADC | Silicon Labs SOIC-8

The Silicon Labs TSA7887ARZ is a micropower, 2-channel, 125-ksps, serial-output 12-bit successive-approximation analog-to-digital converter housed in an 8-pin SOIC (RZ) package. It integrates a precision 2.5V internal reference, supports a single 2.7V to 5.25V analog supply, and consumes only 3.2 mW at 125 ksps with full power-down modes reducing quiescent current to sub-microamp levels. The part accepts true bipolar input ranges via flexible reference configuration. An ADC (analog-to-digital converter) is a data-acquisition integrated circuit that samples continuous analog voltages and converts each sample into a discrete digital code for processing by a microcontroller, DSP, or FPGA. Successive-approximation-register (SAR) ADCs use a binary-search algorithm against a precision DAC and reference to resolve one bit per clock cycle, achieving a deterministic conversion time of N cycles for N-bit resolution. This conversion topology sits in the broader hierarchy: ADC -> data converter -> mixed-signal IC -> semiconductor. SAR ADCs are prized for low latency, deterministic behavior, and absence of pipeline-latency artifacts. Key features include 12-bit resolution with no missing codes, an integrated 2.5V reference, an SPI-/QSPI-/MICROWIRE-compatible serial interface, true-differential analog inputs, software-configurable unipolar/bipolar input ranges, and a hardware-power-down pin. The internal reference can be overdriven with an external source, simplifying ratiometric measurements such as bridge-sensor readings. An on-chip oscillator eliminates the need for an external clock source in cost-sensitive designs. Architecturally, the TSA7887ARZ uses a charge-balancing switched-capacitor DAC front end that converts the input voltage into a digital code across 12 SAR clock cycles. The auto-calibration cycle corrects offset and gain errors on every conversion, eliminating drift across temperature and supply variations. Serial data is clocked out MSB-first and conforms to standard SPI modes, allowing direct connection to most modern microcontrollers without glue logic. Typical applications include portable instrumentation, battery-powered data loggers, industrial process-control loops, sensor conditioning modules, and panel-meter front ends. The low power draw makes it particularly attractive for solar- or energy-harvesting systems where average current budget is critical. The integrated reference and 2-channel mux further reduce total BOM and PCB area in compact designs. When designing with this part, ensure the analog supply is decoupled with a 1uF ceramic plus a 10uF bulk capacitor placed within 5 mm of the AVDD pin. Reference-pin decoupling is equally critical - a 0.1uF ceramic directly across REF should be used. Avoid switching digital traces under the analog front end to preserve SNR. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ যোগাযোগ
TSA7887ARZ-REEL - 12-bit 125ksps 2-ch SAR ADC SOIC-8 | Silicon Labs
TSA7887ARZ-REEL

TSA7887ARZ-REEL - 12-bit 125ksps 2-ch SAR ADC SOIC-8 | Silicon Labs

The Silicon Labs TSA7887ARZ-REEL is a 2-channel, 12-bit successive-approximation analog-to-digital converter (SAR ADC) with a 125 ksps throughput rate and serial SPI-compatible output, housed in an 8-pin SOIC package. The part is designed as an alternate source for the legacy AD7887 and operates from a single +2.7 V to +5.25 V supply while drawing only 0.85 mA typical supply current, supporting micropower applications. An integrated 2.5 V reference and wideband input track-and-hold (500 ns acquisition) simplify front-end design and remove external reference cost. A SAR ADC is a type of analog-to-digital converter that uses a binary search through successive approximation register logic to resolve an analog input against an internal or external reference, producing N-bit results in N conversion cycles. SAR ADCs excel at medium-to-high resolution (12-18 bit) sampling at moderate speeds (10 ksps to 10 Msps) without the pipeline latency of higher-speed flash or pipelined architectures, making them ideal for multiplexed multi-channel data acquisition systems. Within the data-converter hierarchy, the TSA7887ARZ-REEL sits as a precision ADC -> data converter -> signal chain IC -> mixed-signal semiconductor, combining analog input conditioning, reference generation, and digital serial interface on a single die. Key features include a 125 ksps maximum sampling rate, two single-ended analog input channels multiplexed into one ADC core, an internal 2.5 V reference, a low 0.85 mA supply current, a wide input bandwidth track-and-hold (500 ns), and a serial interface compatible with SPI/QSPI/MICROWIRE. The device accepts bipolar-input-capable front end via simple resistor networks and provides an external reference option when system-level drift compensation is required. The 8-pin SOIC footprint supports standard surface-mount assembly flows. Architecturally, the TSA7887ARZ-REEL uses a charge-redistribution DAC array with successive-approximation register logic clocked from an external serial clock up to 2 MHz. The wideband track-and-hold preserves signal fidelity above the Nyquist limit of the 125 ksps sampling rate, while the integrated reference and input MUX eliminate the external analog conditioning typically required for discrete ADC designs. The serial output reduces pin count versus parallel-output ADCs and simplifies galvanic isolation in industrial systems. Typical applications include portable battery-powered instrumentation, industrial process-control loop monitoring, multi-channel data-logger front ends, sensor-signal conditioning for strain-gauge and thermocouple inputs, and touch-screen / resistive-position decoder interfaces. The low 0.85 mA supply current also suits remote or solar-powered sensor nodes. Where higher throughput is needed, the part's SPI-compatible daisy-chain capability lets two devices share a single serial port. When designing with this device, drive the analog inputs from low-impedance buffers (<= 50 ohm source impedance) to avoid conversion errors caused by the kick-back charge of the internal CDAC array. Bypass VDD with a 0.1 uF ceramic plus 10 uF tantalum placed within 5 mm of the supply pin, and provide a clean analog ground return to keep the integrated reference stable. The throughput scales linearly with external SCLK; a 2 MHz SCLK yields the rated 125 ksps. Note that the TSA7887ARZ-REEL is currently listed as obsolete by Silicon Labs (last-time-buy status), so long-life designs should consider the newer AD7887SRZ-EP equivalent. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

RFQ যোগাযোগ
TSA7887BRZ - 12-bit 125kSPS 2-Ch SAR ADC | Silicon Labs
TSA7887BRZ

TSA7887BRZ - 12-bit 125kSPS 2-Ch SAR ADC | Silicon Labs

The Silicon Labs TSA7887BRZ is a 12-bit, 125 kSPS, 2-channel successive-approximation-register (SAR) analog-to-digital converter with an integrated 2.5 V internal reference, housed in an 8-pin SOIC package. It operates from a single 2.7 V to 5.25 V analog supply and provides a serial (SPI/QSPI/MICROWIRE-compatible) data interface, making it well suited to microcontroller- and DSP-based data-acquisition boards where board space is constrained. A SAR ADC is a successive-approximation analog-to-digital converter, a precision converter architecture that resolves each conversion one bit per clock cycle using a sample-and-hold front-end, an internal DAC, and a comparator. SAR converters sit within the broader class of data converters (ADC/DAC), which in turn are part of the signal-chain IC family used for bridging analog sensors to digital processors. Compared with sigma-delta ADCs, SAR parts typically offer lower latency and higher absolute sample rates per channel but at lower resolution, which is why 12-bit 125 kSPS SAR parts are a mainstream choice for general-purpose mixed-signal acquisition. Key features of the TSA7887BRZ include a true 12-bit (no missing codes) conversion throughput of 125 kSPS, a 1 or 2 single-ended input channel multiplexer, an internal 2.5 V reference with low drift, a wide 2.7 V to 5.25 V analog supply range, a serial interface compatible with SPI/QSPI/MICROWIRE, and a low-power shutdown mode that drops the supply current to microamp levels between conversions. The architecture is single-ended with a 1:1 MUX-to-ADC ratio, and a sample-and-hold block acquires a single-ended signal in well under 1 microsecond. Typical applications for the TSA7887BRZ include industrial process control loops, portable instrumentation and battery-powered sensor readouts, optical-module monitoring (laser bias, photodiode current), motor-control feedback channels, and general-purpose system monitoring on microcontroller- or DSP-based designs. The internal reference and small footprint make it especially attractive for board-constrained designs that would otherwise need an external reference IC. When designing considerations, route the analog input traces away from switching-node traces (DC-DC SW node, gate drivers) to preserve INL/DNL, place the 0.1 uF + 10 uF decoupling pair within a few millimeters of the AVDD pin, and avoid driving the analog inputs directly from a low-impedance source without an op-amp buffer to prevent loading of the internal reference. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes that are not found on the manufacturer product page, giving engineers a single decision-ready reference.

RFQ যোগাযোগ
TSA7887BRZ-REEL - 12-Bit 125kSPS 2-CH SAR ADC | Silicon Labs
TSA7887BRZ-REEL

TSA7887BRZ-REEL - 12-Bit 125kSPS 2-CH SAR ADC | Silicon Labs

The Silicon Labs TSA7887BRZ-REEL is a micropower, 2-channel, 125-kilosamples-per-second (kSPS), 12-bit successive-approximation-register (SAR) analog-to-digital converter (ADC) with a serial output interface, supplied in an 8-pin SOIC (R-8/SOIC-8) package on tape-and-reel packaging. It operates from a single 2.7 V to 5.25 V supply and integrates a wide-bandwidth track-and-hold, an internal +2.5 V reference (TSA7887B grade), one single-ended or two single-ended input channels, and a high-speed SPI-/MICROWIRE-/QSPI-/DSP-compatible serial interface. A successive-approximation-register ADC (SAR ADC) is a type of data converter that resolves an analog input to a digital output by performing a binary search through an internal capacitive DAC, one bit per conversion clock cycle. SAR ADCs are characterized by deterministic latency, excellent DC accuracy, and very low power consumption at moderate sampling rates. Within the broader converter hierarchy, this part sits in the data acquisition -> analog-to-digital converter -> SAR ADC -> precision low-power ADC segment. Key features of the TSA7887BRZ-REEL include 12-bit resolution (no missing codes), 125 kSPS throughput, integrated 2.5 V reference, single-supply 2.7 V to 5.25 V operation, low power dissipation suitable for battery and portable applications, and pin-selectable one or two single-ended analog input channels. The wide input bandwidth of the internal track-and-hold permits accurate sampling of input signals beyond the Nyquist frequency, while the serial interface minimizes pin count and board area. Architecturally, the TSA7887BRZ-REEL is a functional second-source for the legacy AD7887 family, sharing the same 8-pin SOIC footprint and pinout. The internal reference (2.5 V, B grade) eliminates the need for an external reference in many designs and provides low drift across temperature. The serial interface supports standard SPI modes, enabling direct connection to microcontrollers and digital signal processors without glue logic. Typical applications include portable and battery-powered instrumentation, industrial process control loops, transducer signal conditioning, multichannel data acquisition front-ends, point-of-contact scanner signal chains, and precision sensor monitoring. The wide supply range and small SOIC-8 footprint make it well suited to space-constrained designs that need deterministic latency and low power consumption. When designing with this part, place the 0.1 µF decoupling capacitor as close as possible to the VDD pin and ensure the analog inputs are driven by low-impedance buffers for full accuracy. The internal reference does not require an external bypass capacitor for normal operation, but a small ceramic capacitor on REF improves noise rejection in hostile environments. This page synthesizes distributor stock and pricing, drop-in compatible same-brand and cross-brand alternatives, application notes and design guidance not always found in the bare manufacturer datasheet, enabling engineers to compare, select, and source the part with confidence.

RFQ যোগাযোগ
TSB011 - Data Unverified, No Confirmed Electronic Component Found
TSB011

TSB011 - Data Unverified, No Confirmed Electronic Component Found

The MPN TSB011 could not be confirmed as a specific electronic component from the verified web data retrieved for this query. Real-time distributor and manufacturer searches returned no unambiguous match for an electronic part with the exact designation TSB011. The search results instead surfaced several unrelated items that share similar designations: an ACCI TannerStone balustrade catalog item (TSB011), a Texas Instruments TSB11C01DL IEEE 1394 FireWire link-layer controller distributed via Rochester Electronics, an Adam Tech TSB-11 terminal block, and an ITT TSB-011 regulator pressure relief device technical service bulletin for automotive fuel systems. What this means: part-number prefixes such as TSB are not exclusive to a single manufacturer, and near-miss designations (TSB011 vs TSB11 vs TSB-011 vs TSB11C01DL) point to completely different products across mechanical, electrical, and automotive domains. Generating electrical specifications for this MPN from these results would risk fabricating data, so all specification values are marked for verification. What is likely related: if the intended part is the Texas Instruments TSB11C01DL, that device is an IEEE 1394 (FireWire) link-layer controller IC classified by DigiKey under Drivers, Receivers, Transceivers within Interface ICs, supplied through Rochester Electronics as an authorized aftermarket source. If the intended part is the Adam Tech TSB-11, that is a terminal block in the Connectors family. Recommended next step: confirm the exact manufacturer prefix and full MPN (including any package suffix) before ordering. This page will be updated once verified datasheet data is available.

RFQ যোগাযোগ
TSI384-133ILV - PCIe to PCI-X Bridge 256-BGA | Renesas Electronics
TSI384-133ILV

TSI384-133ILV - PCIe to PCI-X Bridge 256-BGA | Renesas Electronics

The Renesas TSI384-133ILV is a single-lane PCI Express (PCIe) to PCI/PCI-X bridge IC housed in a 256-ball PBGA (17x17 mm) package. The device supports x1 PCIe link width (configurable to x4 in some variants per datasheet family), bridging PCIe upstream to legacy PCI/PCI-X peripherals, and supports PCI-X frequencies up to 133 MHz and conventional PCI up to 66 MHz. A PCI-to-PCI bridge is a transparent or non-transparent protocol converter that maps transactions between two distinct PCI-family bus segments. PCI Express bridges sit in the broader hierarchy of: PCIe bridge -> PCIe-to-PCI bridge -> I/O bridge -> peripheral controller IC -> interface logic. Within Renesas' PCI/PCIe product family the Tsi384 is the higher-performance, higher-pin-count sibling of the smaller Tsi381 (144-ball BGA, 13x13 mm) for space-constrained designs. Key features of the TSI384-133ILV include transparent, non-transparent, and opaque (semi-transparent) bridging modes, supporting multi-host systems and storage adapter applications requiring domain isolation. The bridge enables superior throughput with up to four PCIe lanes per the family datasheet and supports asymmetric upstream/downstream widths. Industrial temperature grade and RoHS-compliant terminations suit embedded, telecommunications, and industrial computing designs. Architecture-wise the TSI384 combines a hardened PCIe PHY/transaction layer with a PCI/PCI-X controller core operating in conventional or PCI-X mode. The 256-ball PBGA provides the necessary power, ground, and high-speed signal routing headroom for x1 to x4 PCIe widths. Operating supply voltage is 1.2 V core plus I/O rails, supplied via multiple pins. Typical applications include PCI-to-PCI bridging in industrial single-board computers, storage adapter cards requiring domain isolation, legacy I/O expansion for new PCIe-only processors, telecommunications line cards needing PCI/PCI-X peripherals, and embedded PCIe-to-PCI backplane designs. When designing with this part note that it is reported by some distributors as obsolete or under last-time-buy; confirm lifecycle before starting a new design. Use the Renesas cross-reference document to evaluate the smaller-footprint Tsi381-66ILV for cost-sensitive designs. This page synthesises distributor pricing, parametric comparison with cross-brand PCIe bridges, and practical design notes that complement the Renesas Tsi384 user manual referenced in the data sources.

RFQ যোগাযোগ
TSM1285BCSA+ - 12-Bit 300ksps SAR ADC | Silicon Labs
TSM1285BCSA+

TSM1285BCSA+ - 12-Bit 300ksps SAR ADC | Silicon Labs

The Silicon Labs TSM1285BCSA+ is a 12-bit, 300 ksps, single-supply, low-power successive-approximation analog-to-digital converter (ADC) housed in an 8-pin SOIC package. It integrates an internal 2.5 V reference and an SAR core that achieves 12-bit resolution on a single 2.7 V to 3.6 V analog/digital supply. The device is specified across the commercial temperature range -40C to +85C and is sourced from the legacy Touchstone Semiconductor line now carried under the Silicon Labs brand. An SAR (Successive Approximation Register) ADC is a type of data converter that uses a binary-search algorithm against an internal DAC to digitize an analog input in N conversion clock cycles. SAR ADCs sit in the data converter hierarchy between flash converters (fast, expensive, low resolution) and sigma-delta converters (high resolution, slow, dense digital filtering). Because SAR ADCs require no continuous-time oversampling, they are well suited to multiplexed multi-channel acquisition systems, instrumentation loops, and embedded sensor readouts where deterministic latency matters more than extreme dynamic range. Key features include 300 ksps sampling rate, single 2.7 V to 3.6 V supply operation, internal 2.5 V reference, low power consumption, and a serial interface. The serial output simplifies isolation between the analog front end and a digital host MCU or FPGA, reducing board-level pin count compared with parallel-output SAR ADCs and easing PCB routing in mixed-signal designs. The TSM1285BCSA+ uses a charge-redistribution SAR architecture with an internal reference, internal offset calibration, and internal reference-error nulling per the manufacturer datasheet. After full-scale calibration, relative accuracy is specified against the theoretical code transfer function, supporting reliable closed-loop control and instrumentation applications where absolute transfer linearity matters. Typical applications include portable data acquisition systems, industrial process control loops, isolated sensor front ends, motor control current/voltage sense channels, and battery-powered instrumentation. The 2nd-source SOIC-8 footprint and commercial-grade temperature rating make it a flexible part for cost-sensitive mixed-signal designs. When designing with this ADC, ensure the analog input bandwidth does not exceed the device's -3 dB front-end limit; place a small RC anti-alias filter ahead of AIN. Decouple VDD with both bulk and 100 nF ceramic capacitance placed within 5 mm of the supply pin. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet, enabling faster part-selection decisions.

RFQ যোগাযোগ
TSM1285BCSA+T - 12-Bit 300ksps SAR ADC w/ 2.5V Ref | Silicon Labs
TSM1285BCSA+T

TSM1285BCSA+T - 12-Bit 300ksps SAR ADC w/ 2.5V Ref | Silicon Labs

The Silicon Labs TSM1285BCSA+T is a 12-bit, 300 ksps successive-approximation analog-to-digital converter (SAR ADC) with an internal +2.5 V reference, integrated track-and-hold, and a high-speed serial digital interface, packaged in an 8-pin SOIC (0.154 inch / 3.90 mm body width). It operates from a single +2.7 V to +3.6 V supply and draws less than 2.5 mA at full 300 ksps throughput. The device accepts single-ended analog inputs in the 0 V to VREF range, where VREF can be the internal 2.5 V source or an external reference up to AVDD. A SAR ADC is a precision data-acquisition converter that uses a binary search algorithm and an internal capacitive DAC to compare the sampled input against a reference voltage. It is a sub-category of analog-to-digital converters (ADC), itself a subclass of data-converter ICs within mixed-signal semiconductor devices. SAR ADCs are valued for their deterministic latency (no pipeline delay), low power consumption, and excellent DC accuracy, making them the standard choice for multiplexed data-acquisition systems, instrumentation, and sensor signal chains. Key features include ±1 LSB INL (max) typical linearity, an internal track-and-hold capable of handling input bandwidths up to several MHz, a low conversion-mode power dissipation below 2.5 mA, and a power-down mode that drops quiescent current to microamp levels for battery-powered designs. The serial interface is SPI-/QSPI-/MICROWIRE-compatible, allowing direct connection to most microcontrollers and DSPs without glue logic. Architecturally, the TSM1285BCSA+T combines a high-bandwidth track-and-hold, a charge-redistribution SAR core clocked from an internal oscillator, a low-drift buried-Zener reference (trimmed to ±2%), and a low-noise input buffer. The integrated reference removes a common BOM line, saving PCB area and lowering system cost in precision designs. Typical applications include portable instrumentation and data loggers, pen-digitizers and tablet input systems, loop-powered 4-20 mA sensor digitizers, factory-automation sensor front ends, and battery-monitoring modules for portable equipment. Designers should note that the SHDN pin must be driven logic-high for normal conversion and pulled logic-low for power-down. The internal reference output (REF) requires a 2.2 µF minimum bypass capacitor; values lower than this degrade linearity. Input signals must remain within 0 V to VREF to avoid saturation. This page synthesizes distributor pricing, pin-compatible drop-in alternatives including the Maxim MAX1285BCSA family, and practical design notes that are not consolidated in the manufacturer datasheet, supporting faster component evaluation.

RFQ যোগাযোগ
TSM1285BESA+ - 12-Bit 300ksps SAR ADC | Silicon Labs SOIC-8
TSM1285BESA+

TSM1285BESA+ - 12-Bit 300ksps SAR ADC | Silicon Labs SOIC-8

The Silicon Labs TSM1285BESA+ (originally Touchstone Semiconductor) is a 12-bit, 300 ksps successive-approximation analog-to-digital converter in an 8-pin SOIC package, featuring an internal 2.5 V reference and a serial SPI/QSPI/MICROWIRE-compatible interface. The single-channel, single-ended input converter targets low-power, single-supply data-acquisition applications, including industrial instrumentation, process control, and portable sensor readout. The SAR (Successive Approximation Register) architecture is a class of ADC that performs bit-by-bit comparison using an internal DAC and a comparator, achieving deterministic conversion latency and excellent DC accuracy at moderate sampling rates compared with delta-sigma (which trades speed for higher oversampling resolution) or pipeline ADCs (which need higher clock speeds and consume more power). The 12-bit SAR sits in the data-converter hierarchy: ADC -> data converter -> signal chain IC -> mixed-signal semiconductor, and it is commonly used as the analog front-end between sensors or analog signal conditioning blocks and a microcontroller or DSP. Key features include 300 ksps maximum sampling rate, an internal 2.5 V reference (eliminating an external reference IC and saving PCB area), single 4.5 V to 5.5 V analog supply, low power dissipation suitable for battery and loop-powered systems, software-configurable unipolar/bipolar input range via the reference, and a flexible serial interface that supports SPI, QSPI, and MICROWIRE. The 8-SOIC surface-mount package keeps the part compact for high-density data-acquisition boards. The internal 2.5 V reference is trimmed during manufacture and provides the conversion full-scale; this removes one component from the BOM and simplifies factory calibration. The serial interface reduces pin count (no parallel data bus), enabling direct connection to microcontrollers and DSPs without glue logic, and the wide analog supply tolerance allows operation directly from a regulated 5 V rail or a low-dropout linear regulator output. Typical applications include industrial process control loops, weigh scales, panel meters, temperature and pressure sensor digitizers, portable medical instrumentation, and battery monitoring. The 12-bit resolution suits sensor linearization, threshold detection, and slow closed-loop control, while the 300 ksps rate handles audio-bandwidth and motor-control analog channels. When designing with this device, ensure the analog input does not exceed VDD; add a small RC anti-alias filter ahead of the input pin to limit noise above 150 kHz (half the Nyquist rate). Decouple VDD with a 10 uF tantalum plus 0.1 uF ceramic pair placed within 10 mm of the pin. This page synthesizes distributor pricing, drop-in cross-references (MAX1285BESA from Maxim Integrated is a pin-compatible functional twin in the same SOIC-8 footprint), and practical design notes not found in the manufacturer datasheet alone.

RFQ যোগাযোগ
TSM1285BESA+T - 12-Bit 300ksps SAR ADC w/ Int Ref | Silicon Labs
TSM1285BESA+T

TSM1285BESA+T - 12-Bit 300ksps SAR ADC w/ Int Ref | Silicon Labs

The Silicon Labs TSM1285BESA+T is a 12-bit, 300 ksps successive-approximation analog-to-digital converter with an internal 2.5 V reference, offered in an 8-pin SOIC (SO) package. It provides one single-ended input channel, a serial (SPI/QSPI/MICROWIRE-compatible) interface, and operates from a single 2.7 V to 3.6 V analog and digital supply, drawing approximately 1 mA at full sampling rate. The integrated reference eliminates the need for an external precision reference, reducing BOM cost and board area in space-constrained designs. An SAR (Successive Approximation Register) ADC is a type of analog-to-digital converter that uses a binary-search algorithm against an internal or external reference to digitize an input voltage in N clock cycles, producing one sample per conversion with deterministic latency. ADCs sit within the broader data-acquisition signal chain (sensor -> front-end amplifier -> ADC -> microcontroller/DSP) and serve as the bridge between the analog physical world and digital signal processing. Low-power, single-supply 12-bit SAR ADCs like the TSM1285 are widely deployed in industrial sensors, instrumentation, and embedded monitoring. Key features include 12-bit resolution with no missing codes, a 300 ksps maximum sampling rate, an internal 2.5 V reference, a single-ended analog input, and an SPI-compatible serial output. The device delivers typical INL of +/-1 LSB and operates from -40C to +85C, making it suitable for industrial temperature environments. Low power consumption (~1 mA at 300 ksps) and a power-down mode that reduces current to nanoamp levels enable battery-powered and energy-harvesting applications. Architecturally, the TSM1285 uses a charge-redistribution SAR core with an integrated track-and-hold, a precision bandgap reference, and a serial output shift register. The internal reference is trimmed during manufacture, eliminating external trim components. The serial interface supports SPI, QSPI, and MICROWIRE modes, allowing direct connection to most microcontrollers without glue logic. Conversion is initiated via a chip-select falling edge and the result is clocked out on subsequent SCLK rising edges. Typical applications include industrial process control loop monitoring, portable battery-powered instrumentation, data-acquisition front-ends for sensor signals (temperature, pressure, strain), and embedded control systems. The internal reference simplifies designs that previously required an external reference plus a buffer amplifier. When designing with this part, place a 1 nF to 10 nF ceramic bypass capacitor as close as possible to the VDD pin and a 10 uF bulk capacitor at the supply input. Maintain a quiet analog ground return path; do not share the analog ground return with noisy digital currents. The reference decoupling capacitor (typically 4.7 uF on REF) is critical for AC performance. This page synthesizes distributor pricing, drop-in alternatives (same-brand MAX1285 family first, then cross-brand equivalents), and practical design notes not consolidated in the manufacturer datasheet.

RFQ যোগাযোগ
TSV524IQ4T - Quad 1.15MHz CMOS Op-Amp, RRIO | STMicroelectronics
TSV524IQ4T

TSV524IQ4T - Quad 1.15MHz CMOS Op-Amp, RRIO | STMicroelectronics

The STMicroelectronics TSV524IQ4T is a quad CMOS operational amplifier that delivers a 1.15 MHz gain-bandwidth product while consuming only 45 µA per channel at 5 V, in a 16-pin QFN (3x3) package. It operates from a single 2.7 V to 5.5 V supply with rail-to-rail input and output (RRIO) swing, and offers a slew rate of 0.89 V/µs with an input bias current of just 1 pA and a typical input offset voltage of 1 mV. What is a CMOS operational amplifier? A CMOS op-amp is a type of analog integrated circuit that uses complementary metal-oxide-semiconductor transistors in its input and gain stages. Compared to bipolar op-amps, CMOS op-amps typically offer higher input impedance, lower input bias current, and lower quiescent power consumption, making them well-suited for battery-powered and high-impedance sensor interfaces. The TSV524IQ4T sits in the broader taxonomy: operational amplifier -> amplifier IC -> analog IC -> semiconductor. Its RRIO capability means the output can swing within millivolts of both supply rails, maximizing dynamic range in low-voltage single-supply systems. Key features include the high merit factor (1.15 MHz GBW for only 45 µA supply current), 1 pA typical input bias current that simplifies high-impedance sensor signal chains, 100 pF capacitive load drive capability, and the tiny 3x3 mm QFN-16 footprint that enables dense multi-channel designs. An exposed pad (EP) on the package provides a low thermal-resistance path to the PCB, useful when several channels drive continuous loads. Architecturally, the TSV524IQ4T uses a CMOS input stage with rail-to-rail input common-mode range achieved through complementary N/P differential pairs. The output stage is a class-AB CMOS topology that delivers rail-to-rail output swing. This design optimizes the speed-to-power ratio for applications where low quiescent current matters more than raw bandwidth. Typical applications include battery-powered sensor signal conditioning, portable instrumentation, active filters, transducer interfaces, and current-sensing amplifiers. The wide supply range and RRIO capability make it a strong fit for single-cell Li-ion (3.0-4.2 V) and 3.3 V system designs. When designing with this device, note that the QFN-16 package requires careful PCB layout - the exposed thermal pad must be soldered to a sufficiently large copper area to meet the published thermal resistance and to maintain mechanical reliability. Decouple each supply pin with a 100 nF ceramic capacitor placed as close to the IC as possible. This page synthesizes distributor pricing, verified pin-to-pin drop-in alternatives, and PCB/thermal design guidance for the TSV524IQ4T that complements the manufacturer datasheet.

RFQ যোগাযোগ
TSV991ILT - 20MHz Rail-to-Rail Op Amp | STMicroelectronics
TSV991ILT

TSV991ILT - 20MHz Rail-to-Rail Op Amp | STMicroelectronics

The STMicroelectronics TSV991ILT is a single, high-speed, rail-to-rail input/output operational amplifier offering a gain-bandwidth product of 20 MHz and a slew rate of 10 V/µs. It operates from a supply voltage range of 2.5 V to 5.5 V, making it suitable for battery-powered and low-voltage applications. The device is available in the compact SOT-23-5 package, ideal for space-constrained designs. An operational amplifier (op-amp) is a high-gain voltage amplifier with differential inputs and a single-ended output. It is a fundamental building block in analog electronics, used in signal conditioning, filtering, and amplification. The TSV991ILT belongs to the family of general-purpose op-amps, which are characterized by their versatility and ease of use. In the hierarchy of analog components, op-amps are part of the broader category of linear integrated circuits, which also includes comparators and voltage regulators. Key features of the TSV991ILT include rail-to-rail input and output stages, which maximize the dynamic range in low-voltage applications. The device also features a low input offset voltage of 1.5 mV (max) and a low input bias current of 1 pA (typ), ensuring high accuracy in precision circuits. The 20 MHz bandwidth and 10 V/µs slew rate enable the amplifier to handle high-frequency signals, making it suitable for video and communication applications. The TSV991ILT is built on STMicroelectronics' advanced BiCMOS process, which combines the benefits of bipolar and CMOS technologies. This process achieves a good balance between speed, power consumption, and noise performance. The amplifier's quiescent current is typically 1.1 mA, providing a favorable trade-off between speed and power efficiency for battery-operated devices. Typical applications include active filters, signal conditioning, portable instrumentation, and audio processing. The rail-to-rail output capability allows the amplifier to drive ADC inputs directly, maximizing the usable input range. In sensor interfaces, the low input bias current minimizes errors when interfacing with high-impedance sensors. When designing with the TSV991ILT, ensure proper power supply decoupling with a 0.1 µF ceramic capacitor placed close to the VCC pin. The input common-mode voltage range extends beyond the supply rails, but care should be taken to avoid exceeding the absolute maximum ratings. The output can swing within 50 mV of the rails, which is beneficial for single-supply operation. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the STMicroelectronics datasheet, providing a comprehensive resource for engineers evaluating the TSV991ILT.

USD $0.34 যোগাযোগ
TSX9292IST - 16MHz RR 16V CMOS Op-Amp, Dual | STMicroelectronics
TSX9292IST

TSX9292IST - 16MHz RR 16V CMOS Op-Amp, Dual | STMicroelectronics

The STMicroelectronics TSX9292IST is a dual operational amplifier featuring 16 MHz gain-bandwidth product, 27 V/µs slew rate, and 0.0003 % THD+N, housed in an 8-pin MiniSO (Mini Small Outline) package. It operates from a single 4 V to 16 V supply and provides rail-to-rail input and output swing, making it suitable for low-voltage, single-supply, and high-fidelity signal-chain designs. The two on-chip amplifiers are decompensated and stable for gains greater than +2 (or inverting gains less than -1), and each channel draws a typical 2.8 mA quiescent current. A CMOS operational amplifier (op-amp) is a high-gain DC-coupled differential amplifier built on a CMOS process. In a system hierarchy it sits under amplifier ICs -> analog front-end -> signal conditioning -> mixed-signal subsystem. The 'rail-to-rail' designation means the input common-mode range and the output swing can approach both supply rails, which maximizes dynamic range in low-voltage designs - critical when the supply is only 5 V or 3.3 V and every millivolt of headroom counts. Key features include 16 MHz GBP, 27 V/µs slew rate, 0.0003 % THD+N (Total Harmonic Distortion plus Noise), low input bias current from CMOS input stages, and 2.8 mA per-channel quiescent current. The TSX92x family is a pin-compatible upgrade path for legacy TS912/TS914 designs requiring higher AC performance with the same supply range and MiniSO/SO footprint options. The TSX9292IST uses a CMOS input stage that delivers very low input bias current, paired with a class-AB rail-to-rail output stage that swings within tens of millivolts of either rail. The 'IST' suffix denotes the MiniSO-8 (TSSOP-equivalent micro-package) tape-and-reel option, optimized for compact surface-mount layouts. Stability requires a minimum closed-loop gain of 2, meaning the part is not unity-gain stable - it must be used with sufficient gain to maintain phase margin. Typical applications include active filters, audio line drivers and headphone amplifiers, transducer conditioners, motor-control sense amplifiers, and industrial sensor interfaces. The wide supply range (4 V-16 V) makes it equally comfortable in 5 V industrial loops, 12 V automotive subsystems, and ±5 V split-rail instrumentation. When designing with this device, always configure the circuit for closed-loop gain ≥ +2 (or inverting gain ≤ -1) to guarantee stability. Add a small series output resistor (~10-50 Ω) when driving large capacitive loads to prevent peaking, and place a 0.1 µF decoupling capacitor close to each supply pin. Verify output current limits at high supply voltages, as the CMOS output stage can only source or sink tens of milliamps to stay in the linear region. This page synthesizes distributor pricing, drop-in alternative recommendations, and practical design considerations not consolidated on the manufacturer datasheet, with source attribution for every claim.

RFQ যোগাযোগ
TUSB1002RGER - 10Gbps Dual USB 3.1 Redriver | Texas Instruments
TUSB1002RGER

TUSB1002RGER - 10Gbps Dual USB 3.1 Redriver | Texas Instruments

The Texas Instruments TUSB1002RGER is a 10 Gbps dual-channel linear USB 3.1 redriver and signal conditioner in a 24-VQFN package measuring 4 x 4 mm. It operates from a 3.3 V supply, supports USB 3.1 SuperSpeedPlus signal rates, and can compensate for up to 16 dB of Inter-Symbol Interference loss. Its two-channel architecture allows one device to condition both sides of a USB link or two independent USB 3.1 paths. A linear redriver is a type of USB signal conditioner that receives a degraded high-speed differential signal, restores its amplitude and timing margin, and retransmits the signal toward the next USB device. In the broader electronics hierarchy, a redriver belongs to the interface IC and signal-conditioning categories, where it complements controllers, hubs, transceivers, and retimers by recovering connectivity over cables, connectors, and printed circuit board traces. The TUSB1002 uses a linear equalizer to address high-frequency attenuation. According to the Texas Instruments product information, it supports up to 16 dB of loss caused by Inter-Symbol Interference. The device also implements USB 3.1 low-power modes and an ultra-low-power architecture, helping reduce consumption during idle operation. Its 3.3 V supply requirement and 10 Gbps throughput suit equipment requiring long reaches between a USB host or hub and a peripheral. The dual-channel arrangement gives designers flexibility for link-to-link signal conditioning. Each channel can be evaluated and configured for its own PCB or cable path, while common package placement simplifies routing around USB connectors. As a linear device, it preserves the signal waveform while improving amplitude; unlike a protocol-aware retimer, it does not need to recover and reconstruct USB timing at a data rate of 10 Gbps. Typical uses include USB 3.1 docking stations, laptop and tablet accessories, external storage enclosures, industrial test equipment, servers, and data-acquisition systems. It is particularly useful when connector or PCB losses threaten eye closure between a USB host controller and an endpoint device. Place the redriver close to the loss-producing connector or trace segment and follow the manufacturer datasheet's reference layout for high-speed differential routing. Decoupling, impedance control, return-path continuity, and the device's documented layout requirements are essential because an incorrectly positioned redriver can add loss rather than recover margin. This page combines the manufacturer product description with engineering-oriented application analysis, design guidance, lifecycle considerations, and a strict review of drop-in replacement candidates. It is intended to help engineers determine whether the TUSB1002RGER fits a 10 Gbps USB 3.1 channel before committing it to a high-speed PCB layout.

RFQ যোগাযোগ
TUSB1105RGTR - USB 2.0 Transceiver | Texas Instruments
TUSB1105RGTR

TUSB1105RGTR - USB 2.0 Transceiver | Texas Instruments

Texas Instruments TUSB1105RGTR is a single-channel USB 2.0 transceiver for full-speed and low-speed signaling, supporting 12 Mbit/s and 1.5 Mbit/s data rates in a 16-pin VQFN package measuring 3 mm by 3 mm. The device provides one transceiver path, integrates transmit and receive functions, and is designed for compact USB interface implementations. A universal serial bus transceiver is an interface circuit that converts logic-level data into USB-compatible differential signaling and converts received differential signals back into digital logic. The TUSB1105 belongs to the USB interface IC hierarchy, where USB transceivers connect a host, peripheral, or embedded controller to a USB connector while providing the physical-layer signaling required by USB 2.0 devices. The principal features include compliance with the Universal Serial Bus Specification Revision 2.0, full-speed operation at 12 Mbit/s, low-speed operation at 1.5 Mbit/s, and a half-duplex 1/1 transceiver configuration. Its 16-VQFN package is 3 mm by 3 mm, making the device suitable for space-constrained portable, industrial, and embedded USB equipment. The exposed-pad package also supports compact PCB layouts when its land pattern and thermal design are implemented correctly. The TUSB1105 is intended for external USB connectivity rather than direct USB data signaling across a long cable or printed circuit board. Its transmit and receive path handles the USB differential interface, while the connected USB controller or embedded processor performs protocol handling. This division keeps low-level signaling separate from the higher layers of USB enumeration, descriptors, classes, and transfers. Typical uses include USB-to-serial adapters, portable test and measurement equipment, industrial control panels, data-collection terminals, and accessory controllers that need a compact full-speed or low-speed USB interface. For designs that expose a USB Type-A or USB Type-B receptacle, the transceiver should be paired with the appropriate connector, protection network, routing geometry, and controller-specific interface requirements. PCB implementation requires careful treatment of the differential USB pair, the exposed ground pad, and the short connection between the transceiver and connector. Maintain a continuous ground reference, route D+ and D+ together and D− and D− together, and minimize stubs and unnecessary vias. Confirm the final layout against the pin-description and layout guidance in the manufacturer datasheet. This page combines the confirmed USB 2.0 speed ratings, package information, drop-in replacement findings, interface-selection guidance, and practical PCB considerations into a compact engineering reference for USB transceiver designs.

RFQ যোগাযোগ
TUSB1106PWR USB 2.0 Transceiver | Texas Instruments
TUSB1106PWR

TUSB1106PWR USB 2.0 Transceiver | Texas Instruments

The Texas Instruments TUSB1106PWR is a single-channel USB transceiver for Universal Serial Bus applications, supporting full-speed operation at 12 Mbit/s and low-speed operation at 1.5 Mbit/s. The device is compliant with the Universal Serial Bus Specification Revision 2.0 and is packaged in a 16-pin TSSOP (PW) package. It integrates the digital transceiver functions required for a USB host, device, or peripheral interface. A USB transceiver is an interface integrated circuit that converts between a host controller or peripheral controller’s digital signaling and the physical D+ and D- differential pair used by USB. In the broader electronics hierarchy, the TUSB1106 belongs to the USB interface IC family, interface transceivers, and power-management-aware connectivity semiconductors. It provides the physical-layer path for exchanging serial data and detecting bus state in USB 2.0 systems. The TUSB1106 family supports both full-speed and low-speed USB data rates. Full-speed operation provides a higher-rate communication option for peripherals that require more throughput, while low-speed operation supports devices with modest bandwidth requirements and suitable device-state behavior. USB 2.0 Revision 2.0 compliance is specifically identified for the TUSB1105 and TUSB1106 transceivers by Texas Instruments. The TUSB1106PWR is a half-duplex, one-channel transceiver, matching the “1/1 Transceiver Half” device description shown in the product listing. Its differential USB data interface connects to the external data and power behavior of the USB link, while control and configuration pins support integration into host or peripheral designs. The single USB channel makes the device appropriate for compact equipment, industrial control modules, embedded systems, and accessory interfaces that require one USB physical transceiver. Typical design locations include USB host controllers, USB peripheral controllers, portable test equipment, industrial interface cards, and embedded USB-to-serial or USB communication subsystems. The device should be placed near the USB connector so that the high-speed differential traces remain short, continuous, and impedance controlled. Connector-side protection, proper D+ and D- routing, and compliance with the USB signal-integrity requirements are more important than adding unrelated circuit functions. When designing a replacement circuit, verify the complete pin description, electrical limits, operating-temperature range, and USB compliance requirements against the manufacturer datasheet. The principal engineering trade-off is that this device supports USB 2.0 full-speed and low-speed signaling rather than USB high-speed operation at 480 Mbit/s. For new designs that require high-speed USB data rates, select a transceiver explicitly specified for that speed instead. This page organizes the verified manufacturer and distributor information into an engineering-oriented view covering USB data rates, package format, application fit, comparison criteria, and practical design guidance. The package and interface hierarchy are emphasized so engineers can identify whether the TUSB1106PWR matches the intended USB physical-layer design.

RFQ যোগাযোগ
TUSB1106RTZR - USB 2.0 Half-Speed Transceiver | TI
TUSB1106RTZR

TUSB1106RTZR - USB 2.0 Half-Speed Transceiver | TI

Texas Instruments TUSB1106RTZR is a half-speed USB 2.0 transceiver that transmits and receives serial data at both 12 Mbit/s full-speed and 1.5 Mbit/s low-speed rates. The device is packaged in a 16-pin WQFN (RTZ) 3 x 3 mm surface-mount package and includes an integrated bypassable 3.3 V regulator for powering devices from USB VBUS. A USB transceiver is an interface IC that translates logic-level data between a host or hub and a USB peripheral. It belongs to the USB interface transceiver class within the broader interface IC and semiconductor hierarchy. This dual-rate capability allows one device to support both full-speed and low-speed USB links, making it useful in peripheral controllers, portable equipment, industrial interfaces, and legacy USB connectivity designs. The TUSB1106 is compliant with the Universal Serial Bus Specification Revision 2.0. Its principal data-rate ratings are 12 Mbit/s for full-speed operation and 1.5 Mbit/s for low-speed operation. The integrated 3.3 V regulator can be bypassed, giving the system designer a choice between using VBUS-derived power and controlling the regulator enable function. The 16-WQFN package supports compact surface-mount layouts while providing an exposed pad for improved board-level thermal performance. Operation at both USB speed rates expands compatibility with USB peripherals that use full-speed or low-speed signaling. The half-speed transceiver architecture implements one transmit path and one receive path, while the integrated regulator reduces the number of external power-management functions required around a USB peripheral. Designers must still account for USB data-line impedance, ESD protection, connector routing, and the regulator bypass configuration in the system schematic. Typical uses include USB-to-serial bridges, embedded USB peripherals, portable data-acquisition equipment, industrial control interfaces, and USB connectivity for legacy full-speed or low-speed devices. The compact 3 x 3 mm package is particularly useful when board area is constrained but a full USB interface is required without relying on a larger host-side controller. For PCB implementation, route D+ and D+ as a controlled-impedance differential pair, connect the data lines according to the manufacturer's reference layout, and place ESD protection close to the connector. Decouple the 3.3 V output according to the device's recommended capacitor network and verify whether the integrated regulator should be bypassed for the selected power architecture. This product page combines the manufacturer's USB 2.0 compliance information, exact package and temperature details, commercial sourcing guidance, and an analysis of same-footprint alternatives to support faster component selection and PCB design.

RFQ যোগাযোগ
TUSB1146RNQR - 10Gbps USB-C Redriver/MUX | Texas Instruments
TUSB1146RNQR

TUSB1146RNQR - 10Gbps USB-C Redriver/MUX | Texas Instruments

The Texas Instruments TUSB1146RNQR is a USB Type-C crosspoint switch and protocol-agnostic linear redriver supporting USB 3.2 data rates up to 10 Gbps and VESA DisplayPort 2.0 up to 10 Gbps. The device is available in a 40-pin WQFN package measuring 6 mm by 4 mm, with an operating temperature range of 0 °C to 70 °C. It supports USB 3.2 SuperSpeed Plus, two DisplayPort lanes, four DisplayPort lanes, and DisplayPort D_DFP pin assignments C, D, and E. A USB Type-C alternate-mode redriver/MUX is an interface IC that routes high-speed signals between a USB Type-C connector and downstream or host circuitry while compensating for channel loss. It belongs to the signal-conditioning hierarchy of USB interface controllers, redrivers, repeaters, crosspoint switches, and interface ICs. By regenerating and equalizing marginal signals, the TUSB1146 supports reliable high-speed links over longer traces, connectors, cables, or board-to-board transitions than might be possible with passive routing alone. The TUSB1146 supports USB 3.2 Gen 1 and Gen 2 operation up to 10 Gbps, two-lane and four-lane DisplayPort configurations, and DisplayPort 2.0 UHBR10 signaling up to 10 Gbps. Its adaptive equalization adapts the receive equalization to the connected channel. The protocol-agnostic architecture also allows the device to support non-DisplayPort USB Type-C alternate modes such as HDMI Alternate Mode. In a downstream-facing host port, the TUSB1146 functions as a linear redriver for selected USB Type-C SuperSpeed and DisplayPort lanes. Adaptive equalization helps restore signal margin when connector or PCB losses reduce eye opening. The linear redriver architecture is particularly useful where designers need signal regeneration without introducing a protocol-specific conversion stage between the Type-C port and the downstream interface. Typical uses include USB-C docking stations, laptop and tablet docks, multiport adapters, monitor docks, video-capture systems, and industrial USB-C equipment. The D_DFP C, D, and E assignments broaden compatibility with DisplayPort Alternate Mode routing requirements. Systems requiring additional lane routing, conversion, or protocol features should confirm the complete pin configuration and application circuit in the manufacturer datasheet before layout release. Layout is critical in a 10 Gbps redriver design. Route the high-speed differential pairs as controlled-impedance, tightly coupled traces with minimal stubs and continuous reference planes. Place bypass capacitors close to the supply pins, keep the exposed pad thermally and electrically connected as specified, and follow the manufacturer’s recommended layer transitions and return-path guidance to minimize differential-mode and common-mode conversion. This product page combines interface classification, application guidance, design cautions, and structured comparison fields to support faster engineering review. It also separates confirmed TUSB1146RNQR characteristics from parameters that still require inspection of the manufacturer datasheet, helping designers avoid assuming unsupported pin, electrical, or compliance details.

RFQ যোগাযোগ
TUSB1146RNQT - 10Gbps USB-C Alt Mode Redriver | TI
TUSB1146RNQT

TUSB1146RNQT - 10Gbps USB-C Alt Mode Redriver | TI

The Texas Instruments TUSB1146RNQT is a protocol-agnostic USB Type-C Alt Mode redriver and crosspoint switch that supports USB 3.2 data rates up to 10 Gbps and DisplayPort 2.0 up to 10 Gbps. The device is housed in a 40-pin WQFN package measuring 6 mm by 4 mm and is intended for downstream-facing host ports. A USB Type-C Alt Mode redriver is an interface IC that conditions high-speed differential signals between a USB Type-C controller and a connector or peripheral. It supports loss compensation for USB, DisplayPort, and other protocol-agnostic Alt Mode lanes. The TUSB1146 occupies the redriver, multiplexing, and signal-conditioning stages of a USB Type-C power and data interface. The TUSB1146 supports USB 3.2 SuperSpeed signals at up to 10 Gbps and VESA DisplayPort 2.0 at up to 10 Gbps, or UHBR10. It supports USB 3.2 x1 Gen 1 and Gen 2, USB 3.2 SSP, two DisplayPort lanes, and four DisplayPort lanes. Its protocol-agnostic architecture also permits use with other USB Type-C Alt Mode interfaces, including HDMI Alt Mode. The TUSB1146 provides adaptive equalization to compensate for channel loss encountered through PCB traces, connectors, and cables. Its crosspoint-switch architecture supports configurable lane routing for USB and DisplayPort Alt Mode. The manufacturer identifies support for DisplayPort D_DFP pin assignments C, D, and E, making it suitable for systems that require multiple high-speed lane arrangements in a compact host interface. Typical uses include USB-C docking stations, multi-display adapters, notebook and tablet systems, desktop hosts, video-over-USB-C equipment, and industrial data-acquisition systems. The device is particularly relevant where cable or PCB losses could compromise 10 Gbps signal integrity but the host and connector placement cannot be shortened enough to eliminate the loss. When laying out a design, preserve the high-speed signal paths as short and symmetric as possible, provide the reference-plane and return-path structures required by the manufacturer recommendations, and place bypass capacitance close to the supply pins. Differential pair geometry and connector launch transitions are especially important at 10 Gbps because the redriver compensates for loss but cannot remove reflections caused by an inconsistent PCB structure. This page combines the TUSB1146RNQT protocol and package details, application guidance, sourcing information, and a strict assessment of available drop-in replacements. It is intended to help engineers confirm protocol coverage, mechanical fit, thermal expectations, and signal-integrity requirements before integrating the redriver into a USB Type-C Alt Mode design.

RFQ যোগাযোগ
TUSB1310AZAY - 5 Gbps USB 3.0 Transceiver | Texas Instruments
TUSB1310AZAY

TUSB1310AZAY - 5 Gbps USB 3.0 Transceiver | Texas Instruments

Texas Instruments TUSB1310AZAY is a single-port SuperSpeed USB 3.0 physical-layer transceiver with a 5.0 Gbps data rate, PIPE and ULPI interfaces, and a 175-NFBGA package measuring 12 x 12 mm. It operates from one selectable reference clock at 20, 25, 30, or 40 MHz and can provide that clock to a USB controller. A USB 3.0 transceiver is an interface IC that connects a USB controller or host to a SuperSpeed data link. It forms part of the hierarchy USB interface device, transceiver, interface IC, and semiconductor. Unlike a passive connector, the transceiver converts parallel controller data into high-speed differential signaling and receives differential signal information for the controller. The TUSB1310A also supports PIPE and ULPI interfaces, allowing it to connect with controllers that use either interface style. Principal features include one USB 3.0 port, a 5.0 Gbps maximum data rate, four selectable reference-clock frequencies, and integrated USB power-state handling. The USB 3.0 power states named in the manufacturer documentation are U0, U1, U2, and U3. The PIPE specification defines P0, P1, P2, and P3, while the POWER_DOWN pin is mapped to LTSSM states as described in the manufacturer datasheet. The device operates from a single reference clock supplied by either a crystal or an external clock source. The manufacturer describes the 20, 25, 30, and 40 MHz selection as enabling a cost-effective USB 3.0 implementation with few external components. Because the transceiver can provide the reference clock to the USB controller, the design can reduce the number of independent clock sources required on the board. Typical uses include USB 3.0 host-controller systems, USB device controllers, external data-transfer equipment, test and measurement products, and embedded computing platforms that require a SuperSpeed interface. The PIPE and ULPI choices are particularly useful when a system already has a controller designed around one of those interfaces. The 175-NFBGA package also supports compact layouts where the electrical and thermal design can be controlled carefully. When implementing the TUSB1310AZAY, follow the manufacturer datasheet for high-speed differential routing, reference-clock configuration, supply decoupling, ball assignment, and test-point access. Its 12 x 12 mm BGA footprint requires careful escape routing and multilayer PCB planning. Confirm that the selected controller supports the intended PIPE or ULPI mode and verify the complete USB link-training sequence during hardware validation. This page consolidates the exact ordering information, interface capabilities, clock choices, package details, replacement information, and engineering design considerations for engineers evaluating a USB 3.0 SuperSpeed physical-layer implementation.

RFQ যোগাযোগ
TUSB1310ZAY - 5Gbps USB 3.0 Transceiver | Texas Instruments
TUSB1310ZAY

TUSB1310ZAY - 5Gbps USB 3.0 Transceiver | Texas Instruments

The Texas Instruments TUSB1310ZAY is a single-port, 5.0-Gbps USB 3.0 SuperSpeed physical-layer transceiver with PIPE3 and ULPI interfaces, packaged in a 175-ball NFBGA measuring 12 x 12 mm. It accepts a single crystal or external reference clock and can supply a clock to a USB link-layer controller. According to the manufacturer product page, selectable reference-clock frequencies include 20, 25, 30, and 40 MHz, supporting integration into USB 3.0 systems that require a consolidated physical-layer and controller-interface solution. A USB 3.0 SuperSpeed transceiver is the interface device that converts between a host or device controller and the physical USB data path. It belongs to the USB interface IC hierarchy, connects to digital logic through PIPE3 or ULPI, and handles the high-speed physical signaling required by the USB 3.0 protocol. The TUSB1310 therefore sits between a USB link-layer controller and the external connector, power, clock, and signal-routing network. The principal documented features are one USB 3.0 transceiver port, a 5.0-Gbps operating speed, support for both PIPE3 and ULPI controller interfaces, and operation from either a crystal oscillator or an external reference clock. Its four documented reference-clock choices allow the system designer to select a clock appropriate to the controller ecosystem. The device can also provide a clock to the USB link-layer controller, reducing the number of separate clocking arrangements considered in a reference design. The TUSB1310ZAY uses a 175-NFBGA package, identified by the ordering code as a 12 x 12 mm device. This dense ball-grid arrangement is intended for compact systems requiring numerous high-speed connections. Placement is a signal-integrity-critical task because USB 3.0 differential pairs demand short, length-matched routing, appropriate reference planes, and carefully controlled return paths. The transceiver’s interface selection also affects host-versus-device implementation and determines how the controller-facing pins are connected. Typical applications include USB 3.0 docking stations, high-speed data-transfer products, storage systems, test equipment, and embedded computing platforms that use a USB link-layer controller. The transceiver can suit designs requiring either PIPE3 connectivity for parallel controller integration or ULPI connectivity for a compact register-oriented interface. It is particularly relevant where a system needs one USB 3.0 port and a selectable reference-clock arrangement rather than a multi-port hub transceiver. When designing around the TUSB1310ZAY, verify the complete pin configuration, electrical limits, crystal or reference-clock requirements, and decoupling recommendations in the manufacturer datasheet before releasing PCB artwork. High-speed differential routing should be validated against the controller and connector reference designs because package placement, via transitions, layer stackup, and clock jitter can materially affect signal integrity. This page organizes the documented TUSB1310ZAY capabilities, package information, interface options, engineering applications, and confirmed same-package alternatives. It also highlights where a manufacturer data sheet must remain the controlling reference for pin assignment, compliance, environmental limits, and layout implementation.

RFQ যোগাযোগ
TUSB2036AVF - 2/3-Port 12Mbps USB Hub | Texas Instruments
TUSB2036AVF

TUSB2036AVF - 2/3-Port 12Mbps USB Hub | Texas Instruments

Texas Instruments TUSB2036AVF is a 2/3-port, 12-Mbps USB full-speed hub controller with an optional serial EEPROM interface, housed in a 32-pin LQFP package. The device operates from a 3.3-V supply and provides one upstream port plus two or three programmable downstream ports. Its USB 2.0-compliant implementation integrates transceivers for every upstream and downstream connection, while a digital state-machine architecture eliminates firmware programming requirements. A USB hub is a system-level interface component that expands one host connection into multiple peripheral ports. The TUSB2036AVF belongs to the USB interface controller hierarchy, combining USB transceiver circuitry, port-management logic, and optional configuration storage in one CMOS ASIC. This integration simplifies PCB design for legacy full-speed USB systems, printers, industrial peripherals, and embedded equipment that require more than one USB device connection. Key features include integrated upstream and downstream USB transceivers, selectable two- or three-port operation, 12-Mbps full-speed data transfer, and an optional serial EEPROM interface. Because the downstream-port count is selected through an input pin, one board design can support two-port or three-port configurations without changing the controller IC. The digital state-machine implementation also means the hub does not require embedded hub firmware. The controller uses a 3.3-V CMOS logic implementation and provides dedicated USB transceiver functions for all supported ports. Its architecture is intended for full-speed USB 2.0-compatible systems rather than high-speed 480-Mbps operation. Power, decoupling, routing, and signal-integrity layouts must therefore be evaluated specifically for 12-Mbps full-speed signaling rather than high-speed USB impedance rules. Typical applications include USB-to-multiple-peripheral adapters, legacy printer interfaces, industrial control equipment, data acquisition systems, and embedded host platforms using full-speed USB peripherals. The optional EEPROM interface allows port configuration to be stored externally, which is useful when a product requires consistent downstream-port behavior across power cycles. When laying out the PCB, place the controller and supporting passive components close to their associated connector and power-entry points. Keep USB differential traces short, pair them continuously, minimize stub branches, and provide the decoupling network specified by the manufacturer. Confirm the selected two-port or three-port configuration and verify downstream-port power switching before releasing the layout. This page organizes the official product information into a design-oriented view covering USB speed, port topology, logic voltage, configuration options, package considerations, application fit, and replacement limitations. It also distinguishes confirmed device functions from assumptions that require engineering verification against the manufacturer datasheet.

RFQ যোগাযোগ