AD603AQ - 90MHz Low-Noise Variable Gain Amplifier | Analog Devices
MPN: AD603AQ ✓ সক্রিয়AD603AQ সারাংশ
A variable gain amplifier is an amplifier whose gain can be controlled by an external voltage. Positioned between the RF/IF signal path and a downstream receiver, it allows a system to adapt its signal level before digitization or further processing. The AD603AQ belongs to the controlled-amplifier hierarchy, combining low-noise signal amplification with electrical gain adjustment rather than using a fixed-gain operational amplifier.
The AD603AQ offers linear-in-decibel gain control, with selectable gain ranges covering -11 dB to +31 dB and +9 dB to +51 dB. Its low input-noise spectral density is 1.3 nV/√Hz, making it suitable for receiver front ends where amplifier noise can limit weak-signal detection. The 90 MHz bandwidth supports high-gain signal paths, while the 9 MHz mode provides higher gain where narrower bandwidth is sufficient.
The AD603AQ supports dual-polarity operation from ±4.75 V to ±6.3 V. Its gain-control architecture permits intermediate ranges to be arranged using one external resistor. This flexibility allows designers to trade gain against bandwidth while maintaining control over the gain characteristic and system noise contribution.
Typical uses include RF and IF automatic gain control, communication receivers, radio and television signal chains, instrumentation amplifiers, and wideband measurement systems. In an AGC loop, the gain-control voltage can be adjusted to keep received signals within the input range of a downstream mixer, ADC, or demodulator while limiting overload in strong-signal conditions.
PCB implementation should preserve short, controlled routing around the gain-control and external-resistor networks, provide suitable supply bypassing, and maintain signal-impedance consistency. Because this part is offered in a through-hole CERDIP package rather than a compact surface-mount configuration, its footprint is most appropriate for legacy, industrial, test, and aerospace-style equipment where through-hole assembly and serviceability are priorities.
This page combines the manufacturer's gain, bandwidth, noise, supply, and package information with application guidance, replacement analysis, and practical design considerations for engineers evaluating the AD603AQ in RF and IF signal-chain designs.
এর জন্য ড্রপ-ইন বিকল্প AD603AQ — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
AD603SQ/883B
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
AD603AQ সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য
| Product Type | Voltage-controlled variable gain amplifier |
| High-Gain Range | -11 dB to +31 dB |
| High-Gain Range Bandwidth | 90 MHz |
| Low-Gain Range | +9 dB to +51 dB |
| Low-Gain Range Bandwidth | 9 MHz |
| Intermediate Gain Configuration | Programmable with one external resistor |
| Gain Control Characteristic | Linear in dB |
| Input Noise Spectral Density | 1.3 nV/√Hz |
| Supply Voltage Range | ±4.75 V to ±6.3 V |
| অপারেটিং তাপমাত্রার পরিসর | -40°C to +85°C |
| Number of Amplifiers | 1 circuit |
| প্যাকেজ | 8-pin CERDIP |
| মাউন্টিং টাইপ | Through-hole |
| লাইফসাইকেল স্ট্যাটাস | Production |
AD603AQ 8-pin cerdip পিন কনফিগারেশন গাইড
AD603AQ (8-pin cerdip প্যাকেজ)-এর পিন কনফিগারেশন। এই অ্যানালগ কম্পোনেন্টে ইনপুট, আউটপুট ও পাওয়ার সাপ্লাই পিন রয়েছে। অফসেট নাল, কম্পেনসেশন ও এনেবল পিন কনফিগারেশনের জন্য প্রস্তুতকারকের ডেটাশিট দেখুন। সিগন্যাল কন্ডিশনিং ও অ্যামপ্লিফায়ার সার্কিটের জন্য আদর্শ।
এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি AD603AQ.
দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।
সাধারণ ব্যবহার
AD603AQ এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: RF Automatic Gain Control Receiver, IF Intermediate-Frequency Amplification, Communication Receiver Front End, Automatic Gain Control Instrumentation, Wideband Signal-Level Conditioning, Test and Measurement Signal Chain.
RF Automatic Gain Control Receiver
The AD603AQ fits an RF receiver front end where received signal strength varies widely and the system must prevent downstream mixer or converter overload. Its -11 dB to +31 dB range provides 42 dB of control at up to 90 MHz bandwidth, while the linear-in-decibel control characteristic supports predictable gain adjustment from an AGC loop. The 1.3 nV/√Hz input-noise spectral density helps preserve weak-signal sensitivity. Place it after the RF input network and ahead of the gain-control comparator or detector, with short, impedance-controlled interconnects.
সুপারিশকৃত
IF Intermediate-Frequency Amplification
The AD603AQ is well suited to IF signal chains that require programmable attenuation or gain before demodulation and filtering. Its 90 MHz bandwidth in the -11 dB to +31 dB range supports higher-frequency IF paths, while the +9 dB to +51 dB mode provides up to 51 dB when the usable bandwidth is reduced to 9 MHz. The gain-control voltage can follow an AGC detector, reducing overload risk while retaining controlled signal amplitude for the downstream ADC, demodulator, or analog filter.
সুপারিশকৃত
Communication Receiver Front End
In a communication receiver, the AD603AQ can adapt the signal level to changing propagation conditions and transmitter distance. Its selectable gain ranges cover both attenuation and amplification requirements, allowing the design to reduce gain for strong carriers and increase it for weak carriers. The 90 MHz bandwidth supports RF or IF implementations, and dual supplies of ±4.75 V to ±6.3 V provide the required operating environment. A closed-loop detector and control network should keep the gain command within the amplifier's documented range.
সুপারিশকৃত
Automatic Gain Control Instrumentation
The AD603AQ can be used in instrumentation that must maintain a constant downstream level while the measured input changes over a wide range. Its linear-in-decibel gain control supports consistent control-loop scaling, and the two gain-bandwidth choices let designers optimize for either 90 MHz response or up to 51 dB gain at 9 MHz. The external-resistor option permits an intermediate gain arrangement. Validate input range, gain accuracy, loop stability, and settling behavior against the Analog Devices datasheet before using it in a precision measurement path.
সুপারিশকৃত
Wideband Signal-Level Conditioning
The AD603AQ is appropriate for wideband signal-level conditioning when a fixed-gain amplifier cannot accommodate a wide input range. The -11 dB to +31 dB mode permits gain reduction for large signals and moderate amplification for smaller signals, while the 1.3 nV/√Hz input-noise density supports low-noise signal handling. Use the device ahead of an ADC or fixed-gain processing stage, preserve a consistent reference plane between gain stages, and verify that control-loop bandwidth and amplifier bandwidth together provide adequate settling performance.
সুপারিশকৃত
Test and Measurement Signal Chain
The AD603AQ can provide programmable gain in a test and measurement signal chain where amplitude variation must be normalized before analysis. The 90 MHz mode supports higher-frequency waveforms, whereas the 9 MHz mode trades bandwidth for gain up to +51 dB. The external-resistor configuration offers additional flexibility for establishing an intermediate operating range. Designers should evaluate noise, gain linearity, gain-control settling, and output behavior across the intended frequency span, then follow the manufacturer application circuit for bypass and termination values.
সুপারিশকৃত
সুপারিশকৃত পণ্যের সারসংক্ষেপ
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা AD603AQ — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | AD603SQ/883B |
|---|---|---|
| Package | 8-pin CERDIP | 8-pin CERDIP |
| Brand | Analog Devices | Analog Devices |
| Product Type | Voltage-controlled variable gain amplifier | AD603-family variable gain amplifier |
মূল পার্থক্যসমূহ
- Combines attenuation and amplification in one voltage-controlled range (বনামAD603SQ/883B)
- Supports substantially higher gain when bandwidth can be reduced (বনামAD603SQ/883B)
- Provides low-noise input performance for controlled RF and IF amplification (বনামAD603SQ/883B)
ডিজাইন নোট
Keep the AD603AQ signal inputs, output, gain-control connection, and external gain-setting resistor on short PCB paths. Use a continuous ground reference beneath the signal route and maintain consistent impedance between the amplifier and adjacent RF or IF stages. The CERDIP package supports through-hole assembly, but lead inductance and excessive loop area can still degrade high-frequency behavior. Follow the manufacturer's recommended application circuit and component-placement guidance.
Provide decoupled positive and negative supply rails within the specified ±4.75 V to ±6.3 V range. Place the bypass capacitors close to the corresponding supply pins and return them to the same quiet ground reference used by the signal path. Confirm startup sequencing, rail symmetry, and the maximum supply combination before power-up. An abrupt or asymmetric rail condition can exceed the device's intended operating conditions even if the nominal voltages are correct.
Do not treat the two gain ranges as interchangeable bandwidth modes. The -11 dB to +31 dB range has 90 MHz bandwidth, whereas the +9 dB to +51 dB range has 9 MHz bandwidth. Select the range according to the required gain and signal bandwidth, then use the Analog Devices gain equations to establish an intermediate range with one external resistor. Verify the resulting gain-control slope, usable control-voltage span, and stability.
In an AGC system, separate the high-speed signal path from the gain-control and detector path to prevent feedback from modulating the amplifier unintentionally. Maintain controlled impedance and avoid long parallel runs around the gain-control node. Include the detector and loop filter in stability and settling evaluations, because the closed-loop bandwidth must be compatible with both the 90 MHz amplifier mode and the intended system response time.
কমপ্লায়েন্স তথ্য
No specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations were identified for this exact ordering code. Consult the manufacturer product page and current material-declaration documentation before regulatory use.