Analog Devices

AD9631ANZ - 320 MHz Voltage-Feedback Op Amp | Analog Devices

MPN: AD9631ANZ ✓ সক্রিয়
8-pin PDIP Package
সর্বনিম্ন অর্ডার পরিমাণ: 1 |

AD9631ANZ সারাংশ

Analog Devices AD9631ANZ is a single-circuit, voltage-feedback operational amplifier optimized for high-speed signal conditioning, offering 320 MHz bandwidth and unity-gain stability in an 8-pin PDIP package. It is intended for applications requiring wide bandwidth, fast settling, and low distortion, including photodiode receivers, data-acquisition front ends, pulse systems, and high-speed instrumentation.

A high-speed voltage-feedback operational amplifier is an analog IC that amplifies a differential input while preserving timing and waveform fidelity across a broad frequency range. Within the amplifier hierarchy, the AD9631ANZ belongs to the voltage-feedback amplifier family rather than a current-feedback amplifier. Its unity-gain stability permits operation without a compensating resistor in a unity-gain configuration, simplifying the implementation of low-distortion gain-of-one stages.

The AD9631 family uses a voltage-feedback architecture to provide high bandwidth and low distortion. According to the Analog Devices AD9631 Data Sheet, Rev. D, the AD9631 is unity-gain stable, while the related AD9632 is stable at gains of 2 or greater. This stability distinction is important when comparing devices or adapting the amplifier to a new PCB: selecting a gain-stable variant without checking the required noise gain can alter system behavior even when the package and pinout are unchanged.

The AD9631ANZ is offered in an 8-pin PDIP package. Its through-hole package can simplify prototyping, instrumentation assembly, and repair work, although the larger footprint requires more PCB area than a surface-mount alternative. A single amplifier in the package also requires careful feedback routing and grounding because high-speed signals can couple into adjacent traces and supply pins.

Typical uses include receiver front ends, wideband buffer stages, analog pulse conditioning, high-speed sampling systems, test equipment, and communications interfaces. Designers should use short, controlled-impedance feedback paths, maintain a quiet return plane, and place power-decoupling capacitance close to the device to preserve the amplifier's intended bandwidth and distortion performance.

This page combines manufacturer specifications, same-footprint replacement analysis, application guidance, and comparison information to support component selection and board-level implementation. Use the Analog Devices pin-description table and recommended application circuit when assigning PCB tracks and selecting external resistors or capacitors.

এর জন্য ড্রপ-ইন বিকল্প AD9631ANZ — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।

এই সিরিজের ভ্যারিয়েন্ট

একই সিরিজের মডেল যেগুলো drop-in compatible AD9631ANZ (একই form factor এবং footprint) — পার্থক্য রয়েছে Package.

Analog Devices
Package: 8-DIP (0.300 inch, 7.62 mm)
এর সাথে তুলনা করুন AD9631ANZ →

AD9632ANZ

✅ ড্রপ-ইন
Analog Devices
📦 8-pin PDIP
Single voltage-feedback operational amplifier · 1 circuit · 250 MHz · 2 · 2 µA · 2 mV · -40°C to +85°C

মূল্যের জন্য যোগাযোগ করুন

ডেটাশিট দেখুন →

AD9631ANZ সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য

Amplifier Type Voltage-feedback operational amplifier
Number of Circuits 1 circuit
Gain Stability Unity-gain stable
Bandwidth 320 MHz
Architecture Voltage feedback
প্যাকেজ 8-pin PDIP
মাউন্টিং টাইপ Through-hole
Distortion Ultralow distortion

AD9631ANZ 8-pin pdip পিন কনফিগারেশন গাইড

AD9631ANZ (8-pin pdip প্যাকেজ)-এর পিন কনফিগারেশন। এই অ্যানালগ কম্পোনেন্টে ইনপুট, আউটপুট ও পাওয়ার সাপ্লাই পিন রয়েছে। অফসেট নাল, কম্পেনসেশন ও এনেবল পিন কনফিগারেশনের জন্য প্রস্তুতকারকের ডেটাশিট দেখুন। সিগন্যাল কন্ডিশনিং ও অ্যামপ্লিফায়ার সার্কিটের জন্য আদর্শ।

AD9631ANZ-এর জন্য 8-pin pdip প্যাকেজ পিনআউট ডায়াগ্রাম

এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি AD9631ANZ.

দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।

সাধারণ ব্যবহার

AD9631ANZ এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Photodiode Receiver Front End, High-Speed Data Acquisition Front End, Wideband Pulse Conditioning, Signal Instrumentation Buffer, Communications Receiver Signal Path, Industrial Sensor Signal Conditioning.

🌐

Photodiode Receiver Front End

The AD9631ANZ fits a photodiode receiver front end because its 320 MHz bandwidth supports fast optical signal transitions and its unity-gain stability allows a direct gain-of-one input stage. Place it between the detector and downstream ADC or comparator when the detector output requires low-distortion buffering. The short feedback path should surround the input connection rather than wrap around the package, while the photodiode capacitance and cable capacitance must be included in stability testing. A unity-gain configuration is especially useful when the system requires broad bandwidth without adding a compensated noise gain.

🖥️

High-Speed Data Acquisition Front End

AD9631ANZ is appropriate ahead of a high-speed ADC when the analog input must be buffered without materially reducing bandwidth. Its 320 MHz bandwidth and unity-gain-stable voltage-feedback topology provide a straightforward way to preserve fast edges from sensors and signal sources. Place the amplifier near the ADC input and use the shortest practical input and feedback routes to reduce parasitic feedback. Check the ADC input range against the amplifier output swing, and validate the complete source, ADC sampling capacitance, and termination network because capacitive loading can change effective bandwidth and stability.

⚡

Wideband Pulse Conditioning

The AD9631ANZ can condition short pulses, edge-triggered signals, and other waveforms whose timing information would be degraded by a lower-bandwidth amplifier. Its 320 MHz bandwidth is the key attribute for preserving fast transitions, while unity-gain stability simplifies a one-to-one pulse path. Use a solid ground plane, isolate the output from long test-probe connections, and account for probe capacitance during validation. When driving downstream logic, verify output voltage levels and edge requirements rather than relying on nominal bandwidth alone.

🔧

Signal Instrumentation Buffer

AD9631ANZ can serve as the final buffer in a wideband measurement instrument when a 320 MHz signal path is needed and the source impedance is unsuitable for direct downstream measurement. Its unity-gain stability avoids a compensated gain configuration and helps preserve the source waveform. Keep probe and cable effects outside the feedback loop, provide local supply bypassing, and use a controlled ground return to prevent measurement pickup. Evaluate gain error and output offset at the operating temperature range because a high-bandwidth amplifier does not automatically provide the dc accuracy of a precision instrumentation amplifier.

🌐

Communications Receiver Signal Path

AD9631ANZ is appropriate for an intermediate frequency or baseband communications receiver requiring wide bandwidth and low distortion. The 320 MHz bandwidth supports fast modulated or pulsed signals, while unity-gain stability permits use in a gain-of-one stage close to the receiver front end. Use short traces and a continuous reference plane to prevent the output and feedback paths from coupling into the input. The amplifier does not by itself establish channel linearity, so evaluate cascaded distortion, filtering, gain, and noise with the complete receiver signal chain.

🏭

Industrial Sensor Signal Conditioning

AD9631ANZ can condition outputs from fast industrial sensors when the sensor bandwidth is high enough to justify a 320 MHz amplifier. Its unity-gain stability is useful for preserving sensor edges without introducing a high minimum gain, and the 8-pin PDIP package supports through-hole instrumentation prototypes and modular assemblies. Keep sensitive input traces away from digital and power-conversion paths, use local decoupling, and establish a defined ground strategy. Confirm the sensor's output impedance and capacitive loading in the assembled prototype because both can influence amplifier stability and measured response.

What are the key specifications of AD9631ANZ that engineers should know?
The AD9631ANZ is a single-circuit, unity-gain-stable voltage-feedback operational amplifier with 320 MHz bandwidth in an 8-pin PDIP package. According to the Analog Devices AD9631 Data Sheet, Rev. D, its voltage-feedback architecture and unity-gain stability support high-speed, low-distortion signal conditioning. The device is particularly relevant to photodiode receivers, wideband buffers, pulse-processing systems, data-acquisition front ends, and test equipment. Its basic functionality is confirmed, while supply voltage, slew rate, noise, input offset, operating temperature, and exact settling-time limits should be confirmed from the manufacturer datasheet before final design release.
What is the operating bandwidth of AD9631ANZ?
The AD9631ANZ provides 320 MHz bandwidth. This high operating bandwidth identifies it as a wideband voltage-feedback amplifier rather than a general-purpose precision op amp. Analog Devices describes the AD9631 as an ultralow-distortion, high-speed amplifier that is stable at a gain of 1. The figure should therefore be interpreted as the small-signal bandwidth associated with the manufacturer's specified test conditions. Board-level performance can be affected by source impedance, load capacitance, feedback routing, supply bypassing, and PCB parasitics, so those conditions should be evaluated during signal-integrity validation.
Where can I download the AD9631ANZ datasheet PDF?
The official AD9631ANZ datasheet is available through the Analog Devices AD9631 product page at https://www.analog.com/en/products/ad9631.html. The manufacturer identifies the document as Data Sheet, Rev. D. Use the pin-description table, electrical-characteristics table, and typical application circuits when assigning pins and selecting external components. The 8-pin PDIP lead arrangement and pin names should be taken directly from that manufacturer documentation rather than inferred from the distributor illustrations.
Where can I find the AD9631ANZ pinout?
The authoritative AD9631ANZ pinout appears in the pin-description table of the Analog Devices AD9631 Data Sheet, Rev. D. The verified product listing identifies the exact AD9631ANZ orderable as an 8-pin PDIP device. Use the package drawing and pin table together when laying out the through-hole footprint and checking the orientation notch. The complete public pin list is not reproduced here because it was not included in the source excerpts; assign each PCB connection from the manufacturer pin-description table.
What is the difference between AD9631ANZ and AD9632ANZ?
AD9631ANZ is unity-gain stable, while AD9632ANZ is stable at gains of 2 or greater, according to the Analog Devices AD9631/AD9632 family description. Both are identified in the family comparison as high-speed voltage-feedback amplifiers, and the AD9632ANZ comparison specifically places it alongside AD9631ANZ. The stability threshold is the critical selection criterion: use AD9631ANZ when a noise gain of 1 is required, and verify that the selected amplifier remains stable at the minimum system gain before treating AD9632ANZ as a replacement.
When should I choose AD9631ANZ over AD9632ANZ?
Choose AD9631ANZ when the signal chain requires stable operation at unity gain or when the lowest noise gain can fall to 1. The AD9631 is explicitly unity-gain stable, while the AD9632 requires a gain of 2 or greater for stability. AD9632ANZ may be appropriate when the closed-loop gain and system noise gain are always at least 2. This choice is more important than the shared 8-pin PDIP footprint because an unstable gain configuration can cause oscillation, ringing, and corrupted measurements even when the PCB footprint is unchanged.
What is the best drop-in replacement for AD9631ANZ?
AD9632ANZ is the closest same-package drop-in candidate identified for AD9631ANZ, with a stated parameter match of 80% and the same 8-pin PDIP footprint. It is suitable only where the required gain and system noise gain remain at 2 or greater because AD9632ANZ is stable at gains of 2 or greater, whereas AD9631ANZ is unity-gain stable. No additional qualified cross-brand substitutes were established for the exact pinout and electrical requirements. Before replacement, verify supply compatibility, input and output ranges, load behavior, and stability in the manufacturer datasheets.
Can AD9632ANZ replace AD9631ANZ in a unity-gain circuit?
AD9632ANZ cannot be assumed to replace AD9631ANZ in a unity-gain circuit because the two devices have different minimum stable-gain requirements. AD9631ANZ is unity-gain stable, whereas AD9632ANZ is stable at gains of 2 or greater. Although both use an 8-pin PDIP format, mechanical compatibility alone does not establish electrical drop-in compatibility. Retain AD9631ANZ for a genuine gain-of-one stage, or modify and revalidate the circuit so the closed-loop gain and noise gain remain at least 2.
What can replace AD9631ANZ?
AD9632ANZ can serve as a same-footprint candidate when the circuit operates at a gain of 2 or greater and the remaining electrical requirements match. It cannot serve as a direct unity-gain replacement because its minimum stable gain is 2, while AD9631ANZ supports unity-gain operation. Other package variants of the AD9631 family are not drop-in alternatives when their lead form differs. For production substitution, verify the complete electrical tables, reference design requirements, and stability of the actual feedback network rather than relying on the orderable name alone.
Is AD9631ANZ suitable for photodiode receiver and pulse-processing applications?
AD9631ANZ is suitable for photodiode receiver and pulse-processing front ends because it combines 320 MHz bandwidth with unity-gain stability and a voltage-feedback architecture. Analog Devices positions the AD9631 as an ultralow-distortion, wideband amplifier suitable for pin-diode receiver and high-speed analog signal-conditioning applications. The amplifier can be used where a low-gain buffer must preserve fast transitions. In implementation, keep the photodiode and feedback paths short, account for photodiode capacitance, and validate stability with the actual source impedance and load.
Where can I buy AD9631ANZ and how do I request current availability?
Current availability and sourcing for AD9631ANZ should be requested through the Request a Quote form on this product page. The exact MPN is an 8-pin PDIP ordering option, so include the full suffix AD9631ANZ when requesting a quote to avoid confusion with related surface-mount variants. The manufacturer product page identifies the AD9631 family as production, while distributor inventory can change by region and time. Use the quote form for current lot availability, minimum order quantity, lead time, and shipment details.
What is the price of AD9631ANZ?
The current commercial price for AD9631ANZ should be obtained through the Request a Quote form on this page. The form allows buyers to request the exact 8-pin PDIP ordering option without relying on a changing market listing. Request quantity breaks, authorized-channel availability, lot status, and lead time when preparing production procurement. Because pricing and inventory are time-sensitive, a dated market observation should not be treated as a firm quotation or used as the basis for an approved BOM cost.
What is the lead time for AD9631ANZ?
The current lead time for AD9631ANZ should be requested through the Request a Quote form on this page using the complete orderable MPN. Lead time depends on quantity, package format, lot availability, and manufacturing conditions, so it should be confirmed for each planned build rather than inferred from a generic family statement. For prototype work, request the quantity needed for assembly and bring-up; for production, request a dated schedule that includes replenishment lead time and any factory or distribution allocation constraints.
Is AD9631ANZ in stock?
AD9631ANZ availability should be confirmed through the Request a Quote form on this product page at the time of order. The manufacturer identifies the AD9631 family as production, and distributor listings indicate that the exact 8-pin PDIP device is offered, but inventory levels are not fixed facts. Submit the required quantity and target assembly date to obtain a current response. This approach also allows buyers to distinguish stock allocation from factory lead time and to obtain packaging and traceability information for the selected lot.
What PCB layout practices are important for AD9631ANZ?
Place power-decoupling capacitors close to the device and keep the feedback loop as short and direct as practical. Use a continuous ground reference, avoid routing high-speed output feedback alongside noisy input or supply traces, and minimize parasitic capacitance at the amplifier pins. The manufacturer application circuit provides the reference for decoupling and resistor selection. Because the AD9631ANZ supports 320 MHz bandwidth and unity-gain operation, layout-induced feedback, capacitive loading, and supply-impedance effects can materially affect stability and distortion even when the schematic is correct.

এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা AD9631ANZ — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।

নির্বাচন গাইড

Choose AD9631ANZ for high-speed signal paths that require a gain-of-one stage, particularly photodiode buffers, ADC input conditioning, fast pulse paths, and communications receiver interfaces. Its 320 MHz bandwidth and unity-gain stability are the decisive features. Consider AD9632ANZ when the amplifier is used only at a closed-loop and system noise gain of 2 or greater and its manufacturer specifications satisfy the remaining electrical requirements. The AD9632ANZ shares the 8-pin PDIP format, but it is not interchangeable in a unity-gain design. Surface-mount variants from the same AD9631 family should be treated as new-layout choices rather than drop-in replacements. For every option, verify supply voltage, input and output ranges, output loading, distortion, temperature limits, and stability using the complete manufacturer datasheet and the actual source and load impedances.

বিকল্পের সাথে তুলনা

পারামিটার এই পণ্য AD9632ANZ
Brand Analog Devices Analog Devices
Package 8-pin PDIP 8-pin PDIP
Number of Circuits 1 circuit 1 circuit
Amplifier Architecture Voltage feedback Voltage feedback
Minimum Stable Gain 1 2
Distortion Ultralow distortion Ultralow distortion
Product Family AD9631 AD9632

মূল পার্থক্যসমূহ

  • Supports a direct unity-gain signal path (বনামAD9632ANZ)
  • 320 MHz high-speed operation (বনামAD9632ANZ)
  • Single amplifier in an 8-pin PDIP package (বনামAD9632ANZ)

ডিজাইন নোট

Keep the input, output, feedback, and ground paths short, and avoid routing the feedback trace parallel to a high-speed output trace. The AD9631ANZ's 320 MHz bandwidth makes small parasitic capacitances and loop delays more significant than they would be in a low-frequency amplifier. Place any compensation or gain-setting components directly at the relevant pins, use a continuous ground reference, and inspect the final assembly for unintended feedback loops before measuring performance.

Use short, low-inductance connections from the power pins to local decoupling capacitors, and provide a quiet return path for each supply connection. Follow the capacitor values and connection arrangement in the manufacturer's typical application circuit. High-frequency supply impedance can affect output-noise behavior and phase margin, particularly when the amplifier drives capacitive loads. Validate the populated board with supply ripple and transient measurements because a schematic-level bypass arrangement does not guarantee the same impedance in the physical layout.

Do not treat the common 8-pin PDIP footprint as proof that every AD963x family member is electrically interchangeable. AD9631ANZ is unity-gain stable, whereas AD9632ANZ is stable at gains of 2 or greater. Confirm the minimum system noise gain, supply requirements, input and output ranges, load behavior, and compensation method before substituting a part. A unity-gain circuit using AD9632ANZ can become unstable even though its mechanical footprint matches AD9631ANZ.

Treat the amplifier, source, load, and feedback network as one signal path when checking bandwidth and stability. Photodiode capacitance, ADC kickback, long cable capacitance, and probe loading can create unintended poles even when the AD9631ANZ datasheet bandwidth is 320 MHz. Use controlled-impedance interconnects, terminate unused test connections, and measure time-domain rise time and ringing in the assembled board. Compare results with a simulation using the actual source and load models before release.

কমপ্লায়েন্স তথ্য

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
লিড ফ্রি
Unknown
হ্যালোজেন ফ্রি
Unknown
কনফ্লিক্ট মিনারেলস
Unknown

The Analog Devices product page identifies the AD9631 family as production, but the source excerpts do not provide RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations. AEC-Q100 is not applicable to this general-purpose operational amplifier.

ডেটা যাচাই করা হয়েছে: 2026-11-19 — ডেটা XAIPART-এর কম্পোনেন্ট ইঞ্জিনিয়ারিং টিম দ্বারা যাচাই ও কিউরেট করা হয়েছে

সম্পর্কিত অনুসন্ধান

AD9631ANZ datasheet AD9631ANZ pinout AD9631ANZ datasheet pdf AD9631ANZ equivalent AD9631ANZ replacement AD9631ANZ vs AD9632ANZ AD9631ANZ 320 MHz AD9631ANZ 8-pin PDIP AD9631ANZ unity gain stable AD9631ANZ price AD9631ANZ stock Analog Devices AD9631ANZ

সম্পর্কিত কম্পোনেন্ট ও শর্তাবলী

Analog Devices AD9631ANZ AD9631 AD9632ANZ voltage-feedback amplifier operational amplifier high-speed amplifier unity-gain stable 320 MHz bandwidth low distortion 8-pin PDIP PDIP package family through-hole package surface-mount technology photodiode receiver data acquisition pulse conditioning communications receiver signal integrity feedback stability power-supply decoupling Analog Devices AD9631 Data Sheet, Rev. D RoHS REACH
তাৎক্ষণিক বিলওয়াছে রেকোজিউইট
সম্পূর্ণ বিবরণ পূরণ করুন — আমাদের সেলস টিম 24 ঘণ্টার মধ্যে উত্তর দেবে
পার্ট নম্বর উৎপাদক প্যাকেজ QTY লক্ষ্যমূল্য প্রসারিত
✓
বিল প্রস্তুত করা হয়েছে!

আমরা ২৪ ঘণ্টার মধ্যে আপনার ইমেইলে প্রত্যুত্তর দেব

1
RFQ জমা হয়েছে
2
কোটেশন পাওয়া গেছে
3
অর্ডার দেওয়া হয়েছে
4
পেমেন্ট
5
শিপ করা হয়েছে
6
ডেলিভারি হয়েছে
RFQ বিবরণ দেখুন