AD9631ANZ - 320 MHz Voltage-Feedback Op Amp | Analog Devices
부품 번호: AD9631ANZ ✓ 활성AD9631ANZ 개요
A high-speed voltage-feedback operational amplifier is an analog IC that amplifies a differential input while preserving timing and waveform fidelity across a broad frequency range. Within the amplifier hierarchy, the AD9631ANZ belongs to the voltage-feedback amplifier family rather than a current-feedback amplifier. Its unity-gain stability permits operation without a compensating resistor in a unity-gain configuration, simplifying the implementation of low-distortion gain-of-one stages.
The AD9631 family uses a voltage-feedback architecture to provide high bandwidth and low distortion. According to the Analog Devices AD9631 Data Sheet, Rev. D, the AD9631 is unity-gain stable, while the related AD9632 is stable at gains of 2 or greater. This stability distinction is important when comparing devices or adapting the amplifier to a new PCB: selecting a gain-stable variant without checking the required noise gain can alter system behavior even when the package and pinout are unchanged.
The AD9631ANZ is offered in an 8-pin PDIP package. Its through-hole package can simplify prototyping, instrumentation assembly, and repair work, although the larger footprint requires more PCB area than a surface-mount alternative. A single amplifier in the package also requires careful feedback routing and grounding because high-speed signals can couple into adjacent traces and supply pins.
Typical uses include receiver front ends, wideband buffer stages, analog pulse conditioning, high-speed sampling systems, test equipment, and communications interfaces. Designers should use short, controlled-impedance feedback paths, maintain a quiet return plane, and place power-decoupling capacitance close to the device to preserve the amplifier's intended bandwidth and distortion performance.
This page combines manufacturer specifications, same-footprint replacement analysis, application guidance, and comparison information to support component selection and board-level implementation. Use the Analog Devices pin-description table and recommended application circuit when assigning PCB tracks and selecting external resistors or capacitors.
드롭인 대체품: AD9631ANZ — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.
이 시리즈의 변형
다음과 드롭인 호환되는 동일 시리즈 모델: AD9631ANZ (동일 폼 팩터 및 풋프린트) — 차이점: Package.
AD9632ANZ
✅ 드롭인가격 문의
데이터시트 보기 →AD9631ANZ 최대 정격 & 전기적 특성
| Amplifier Type | Voltage-feedback operational amplifier |
| Number of Circuits | 1 circuit |
| Gain Stability | Unity-gain stable |
| Bandwidth | 320 MHz |
| Architecture | Voltage feedback |
| 패키지 | 8-pin PDIP |
| 실장 유형 | Through-hole |
| Distortion | Ultralow distortion |
AD9631ANZ 8-pin pdip 핀 구성 가이드
AD9631ANZ(8-pin pdip 패키지)의 핀 구성입니다. 이 아날로그 부품에는 입력, 출력, 전원 공급 핀이 있습니다. 오프셋 널, 보상, 인에이블 핀 구성은 제조사 데이터시트를 참조하십시오. 신호 컨디셔닝 및 증폭기 회로에 이상적입니다.
다음에 대한 상세 핀아웃 데이터 없음: AD9631ANZ.
다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.
일반적인 애플리케이션
AD9631ANZ 적합 용도: 6 애플리케이션s: Photodiode Receiver Front End, High-Speed Data Acquisition Front End, Wideband Pulse Conditioning, Signal Instrumentation Buffer, Communications Receiver Signal Path, Industrial Sensor Signal Conditioning.
Photodiode Receiver Front End
The AD9631ANZ fits a photodiode receiver front end because its 320 MHz bandwidth supports fast optical signal transitions and its unity-gain stability allows a direct gain-of-one input stage. Place it between the detector and downstream ADC or comparator when the detector output requires low-distortion buffering. The short feedback path should surround the input connection rather than wrap around the package, while the photodiode capacitance and cable capacitance must be included in stability testing. A unity-gain configuration is especially useful when the system requires broad bandwidth without adding a compensated noise gain.
추천
High-Speed Data Acquisition Front End
AD9631ANZ is appropriate ahead of a high-speed ADC when the analog input must be buffered without materially reducing bandwidth. Its 320 MHz bandwidth and unity-gain-stable voltage-feedback topology provide a straightforward way to preserve fast edges from sensors and signal sources. Place the amplifier near the ADC input and use the shortest practical input and feedback routes to reduce parasitic feedback. Check the ADC input range against the amplifier output swing, and validate the complete source, ADC sampling capacitance, and termination network because capacitive loading can change effective bandwidth and stability.
추천
Wideband Pulse Conditioning
The AD9631ANZ can condition short pulses, edge-triggered signals, and other waveforms whose timing information would be degraded by a lower-bandwidth amplifier. Its 320 MHz bandwidth is the key attribute for preserving fast transitions, while unity-gain stability simplifies a one-to-one pulse path. Use a solid ground plane, isolate the output from long test-probe connections, and account for probe capacitance during validation. When driving downstream logic, verify output voltage levels and edge requirements rather than relying on nominal bandwidth alone.
추천
Signal Instrumentation Buffer
AD9631ANZ can serve as the final buffer in a wideband measurement instrument when a 320 MHz signal path is needed and the source impedance is unsuitable for direct downstream measurement. Its unity-gain stability avoids a compensated gain configuration and helps preserve the source waveform. Keep probe and cable effects outside the feedback loop, provide local supply bypassing, and use a controlled ground return to prevent measurement pickup. Evaluate gain error and output offset at the operating temperature range because a high-bandwidth amplifier does not automatically provide the dc accuracy of a precision instrumentation amplifier.
추천
Communications Receiver Signal Path
AD9631ANZ is appropriate for an intermediate frequency or baseband communications receiver requiring wide bandwidth and low distortion. The 320 MHz bandwidth supports fast modulated or pulsed signals, while unity-gain stability permits use in a gain-of-one stage close to the receiver front end. Use short traces and a continuous reference plane to prevent the output and feedback paths from coupling into the input. The amplifier does not by itself establish channel linearity, so evaluate cascaded distortion, filtering, gain, and noise with the complete receiver signal chain.
추천
Industrial Sensor Signal Conditioning
AD9631ANZ can condition outputs from fast industrial sensors when the sensor bandwidth is high enough to justify a 320 MHz amplifier. Its unity-gain stability is useful for preserving sensor edges without introducing a high minimum gain, and the 8-pin PDIP package supports through-hole instrumentation prototypes and modular assemblies. Keep sensitive input traces away from digital and power-conversion paths, use local decoupling, and establish a defined ground strategy. Confirm the sensor's output impedance and capacitive loading in the assembled prototype because both can influence amplifier stability and measured response.
추천
추천 제품 요약
엔지니어링 참조 데이터: AD9631ANZ — 비교, 설계 지침 및 규정 준수 정보.
선택 가이드
대체품과의 비교
| 파라미터 | 이 제품 | AD9632ANZ |
|---|---|---|
| Brand | Analog Devices | Analog Devices |
| Package | 8-pin PDIP | 8-pin PDIP |
| Number of Circuits | 1 circuit | 1 circuit |
| Amplifier Architecture | Voltage feedback | Voltage feedback |
| Minimum Stable Gain | 1 | 2 |
| Distortion | Ultralow distortion | Ultralow distortion |
| Product Family | AD9631 | AD9632 |
주요 차별점
- Supports a direct unity-gain signal path (vs AD9632ANZ)
- 320 MHz high-speed operation (vs AD9632ANZ)
- Single amplifier in an 8-pin PDIP package (vs AD9632ANZ)
설계 노트
Keep the input, output, feedback, and ground paths short, and avoid routing the feedback trace parallel to a high-speed output trace. The AD9631ANZ's 320 MHz bandwidth makes small parasitic capacitances and loop delays more significant than they would be in a low-frequency amplifier. Place any compensation or gain-setting components directly at the relevant pins, use a continuous ground reference, and inspect the final assembly for unintended feedback loops before measuring performance.
Use short, low-inductance connections from the power pins to local decoupling capacitors, and provide a quiet return path for each supply connection. Follow the capacitor values and connection arrangement in the manufacturer's typical application circuit. High-frequency supply impedance can affect output-noise behavior and phase margin, particularly when the amplifier drives capacitive loads. Validate the populated board with supply ripple and transient measurements because a schematic-level bypass arrangement does not guarantee the same impedance in the physical layout.
Do not treat the common 8-pin PDIP footprint as proof that every AD963x family member is electrically interchangeable. AD9631ANZ is unity-gain stable, whereas AD9632ANZ is stable at gains of 2 or greater. Confirm the minimum system noise gain, supply requirements, input and output ranges, load behavior, and compensation method before substituting a part. A unity-gain circuit using AD9632ANZ can become unstable even though its mechanical footprint matches AD9631ANZ.
Treat the amplifier, source, load, and feedback network as one signal path when checking bandwidth and stability. Photodiode capacitance, ADC kickback, long cable capacitance, and probe loading can create unintended poles even when the AD9631ANZ datasheet bandwidth is 320 MHz. Use controlled-impedance interconnects, terminate unused test connections, and measure time-domain rise time and ringing in the assembled board. Compare results with a simulation using the actual source and load models before release.
규정 준수 정보
The Analog Devices product page identifies the AD9631 family as production, but the source excerpts do not provide RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations. AEC-Q100 is not applicable to this general-purpose operational amplifier.