ADM238LARZ - 4/4 RS-232 Transceiver, 120 kbps | Analog Devices
MPN: ADM238LARZ ✓ সক্রিয়ADM238LARZ সারাংশ
An RS-232 transceiver is an interface IC that combines differential line drivers and receivers for point-to-point serial communication. The ADM238L belongs to the ADM2xx interface family and supports EIA-232-E and V.28 communications requirements. Its integrated charge-pump circuitry simplifies system power architecture while reducing the number of external power rails required by an RS-232 port.
Key features include a 4.75 V to 5.25 V supply range, four transmit channels, four receive channels, a 120 kbps maximum data rate, and operation from small 1 µF capacitors. The device also provides low-power shutdown with supply current no greater than 1 µA. Receiver inputs accept signals up to ±30 V, improving tolerance of transients and off-port voltage conditions encountered in industrial communication environments.
The ADM238LARZ is designed for full-duplex RS-232 links, providing four independent driver outputs and four receiver inputs in one package. Integrated dc-to-dc converters generate the bipolar voltage needed for RS-232 output levels from the single 5 V system supply. This architecture is useful when a board cannot provide the traditional ±12 V or ±15 V RS-232 rail but still needs standards-compliant driver swing.
Typical applications include industrial serial-port equipment, instrumentation, test and measurement systems, data acquisition units, and communications interfaces built around legacy DB9 or equivalent RS-232 connectors. The four-channel arrangement reduces package count when several RS-232 ports must be supported on a compact board.
When laying out the design, place the required 1 µF capacitors close to their associated supply and charge-pump pins. Keep RS-232 driver outputs away from sensitive analog and high-speed digital traces, and connect the device ground to the appropriate interface reference ground. Confirm connector-side protection requirements separately because receiver input tolerance does not replace a correctly selected surge-protection network.
This product page combines the manufacturer’s electrical specifications, package and lifecycle information with practical application guidance, interface trade-offs, and an engineering-focused comparison of documented ADM238L variants. It is intended to help designers determine whether the ADM238LARZ matches their voltage, channel-count, speed, and packaging requirements before committing a board layout.
এর জন্য ড্রপ-ইন বিকল্প ADM238LARZ — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
এই পণ্যের জন্য কোনো ড্রপ-ইন বিকল্প পাওয়া যায়নি।
বিকল্প অনুরোধ করুনADM238LARZ বিশেষণ
| Product Type | RS-232 transceiver |
| Number of Drivers | 4 |
| Number of Receivers | 4 |
| Operating Mode | Full duplex |
| Supply Voltage Range | 4.75 V to 5.25 V |
| Maximum Data Rate | 120 kbps |
| RS-232 Output Swing | ±9 V with a 5 V supply |
| External Capacitor Value | 1 µF |
| Shutdown Supply Current | ≤1 µA |
| Receiver Input Voltage Range | ±30 V |
| Compliance | EIA-232-E and V.28 |
| প্যাকেজ | 24-pin SOIC |
| Package Width | 7.50 mm |
| মাউন্টিং টাইপ | Surface mount |
| Packaging | Tube |
| Latch-Up Protection | Latch-up free |
ADM238LARZ 7.50 mm পিন কনফিগারেশন গাইড
ADM238LARZ (7.50 mm প্যাকেজ)-এর পিন কনফিগারেশন। পিন নম্বরিং, ফাংশন এবং সংযোগ ডায়াগ্রাম প্রস্তুতকারকের ডেটাশিটে সংজ্ঞায়িত করা আছে। সঠিক ফুটপ্রিন্ট এবং সোল্ডারিং নির্দেশিকার জন্য এটি দেখুন।
এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি ADM238LARZ.
দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।
সাধারণ ব্যবহার
ADM238LARZ এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Industrial Serial Port Interface, Instrumentation and Data Acquisition, Test and Measurement Equipment, Communications and Networking Equipment, Data Acquisition Units, Embedded Serial Port Expansion.
Industrial Serial Port Interface
The ADM238LARZ suits industrial equipment that needs several RS-232 ports but has only a 5 V power rail. Its four drivers and four receivers support full-duplex channels at up to 120 kbps, while the integrated dc-to-dc converters generate approximately ±9 V output swing without separate positive and negative rails. A system can therefore place multiple serial links behind a single interface IC. The design must still provide the specified 1 µF charge-pump capacitors, maintain a quiet 5 V supply, and use connector-side protection appropriate to the installation environment.
সুপারিশকৃত
Instrumentation and Data Acquisition
The ADM238LARZ is useful in laboratory instruments and data-acquisition equipment that exchanges commands and measurements through RS-232. Four transmit and four receive channels reduce the number of interface ICs required on a crowded control board, and the 120 kbps rate is suitable for many command and measurement protocols. Because the device runs from a single 4.75 V to 5.25 V supply, it integrates easily with modern digital systems. Designers should verify the protocol’s timing requirements and provide reliable reference grounding between the instrument and connected equipment.
সুপারিশকৃত
Test and Measurement Equipment
The ADM238LARZ can connect test instruments, programmable supplies, and laboratory controllers that retain RS-232 command interfaces. Its four full-duplex channels allow several devices to share one host through separate port circuits, while 120 kbps operation covers common serial-control protocols. The integrated converters eliminate a separate ±12 V supply from the instrument’s power tree. Keep the RS-232 traces away from sensitive measurement circuitry, use the datasheet’s charge-pump capacitor layout, and install suitable protection at exposed connectors.
সুপারিশকৃত
Communications and Networking Equipment
The ADM238LARZ supports legacy RS-232 links found in communications equipment, routers, and service interfaces that have not migrated to differential signaling. Four drivers and four receivers provide a compact implementation of multiple point-to-point links, and the 120 kbps rate accommodates common configuration and control protocols. The single 5 V operating range simplifies interface design around modern processors. Engineers should confirm that each connected port uses the correct signal-to-ground reference and add ESD or surge protection where cables leave the enclosure.
সুপারিশকৃত
Data Acquisition Units
The ADM238LARZ can connect a compact data-acquisition unit to legacy laboratory computers or controller boards over RS-232. Combining four drivers and four receivers in one 24-pin SOIC allows several sensor or instrument channels to share the interface section without multiplying board area. Its 120 kbps limit should be compared with the actual sample transfer rate and protocol overhead. Use short, well-routed traces, maintain a common reference ground, and follow the manufacturer’s capacitor placement recommendations to preserve stable charge-pump operation.
সুপারিশকৃত
Embedded Serial Port Expansion
The ADM238LARZ expands a processor board that lacks enough native RS-232 ports. Four driver outputs and four receiver inputs can support multiple full-duplex connections while operating from the same 5 V rail used by the embedded controller. The device’s 120 kbps data rate is appropriate for configuration, diagnostic, and control traffic rather than high-throughput storage transfer. Firmware must control the supported UART channels and flow-control requirements, and the PCB should reserve connector protection and unobstructed routing space for each external cable attachment.
সুপারিশকৃত
সুপারিশকৃত পণ্যের সারসংক্ষেপ
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা ADM238LARZ — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য |
|---|---|
| Brand | Analog Devices |
| Package | 24-pin SOIC |
| Product Type | RS-232 transceiver |
| Number of Drivers | 4 |
| Number of Receivers | 4 |
| Operating Mode | Full duplex |
| Supply Voltage Range | 4.75 V to 5.25 V |
| Maximum Data Rate | 120 kbps |
| RS-232 Output Swing | ±9 V with a 5 V supply |
| External Capacitor Value | 1 µF |
| Shutdown Supply Current | ≤1 µA |
| Receiver Input Voltage Range | ±30 V |
মূল পার্থক্যসমূহ
- Combines four full-duplex RS-232 channels in one interface IC (বনামADM238LJN)
- Uses a single 5 V rail with integrated dc-to-dc conversion (বনামADM238LAQ)
- Supports four receiver inputs with ±30 V tolerance (বনামADM238LJRZ-REEL)
ডিজাইন নোট
Place the 1 µF charge-pump capacitors close to their specified pins using the shortest possible traces. Keep these high-current switching paths away from receiver inputs, low-level analog signals, and crystal or clock routing. Use a continuous ground plane under the device where practical and connect the ground pins directly to that plane to minimize return-path inductance and charge-pump noise coupling.
Do not treat the ±30 V receiver input tolerance as a substitute for connector protection. The tolerance helps with transients and off-port voltage conditions, but exposed cables can present much larger surge voltages. Select an appropriate RS-232 TVS or surge network, verify its capacitance and standoff voltage against the 120 kbps requirement, and install it near the connector rather than at the transceiver.
Separate RS-232 driver outputs from sensitive receiver and measurement circuits to prevent output crosstalk into low-level inputs. Route each interface as a referenced, point-to-point connection rather than as an uncontrolled multidrop bus. Preserve the recommended ground relationship between communicating systems, and avoid long parallel runs with unrelated digital or switching-regulator traces where a cable transition could couple noise into the port.
কমপ্লায়েন্স তথ্য
The device meets EIA-232-E and V.28 interface specifications and is described as latch-up free. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status were not established for this exact orderable variant.