ADS7864Y/2K - 12-Bit 6-Channel Simultaneous ADC | Texas Instruments
MPN: ADS7864Y/2K ✓ সক্রিয়ADS7864Y/2K সারাংশ
An ADC is a data-acquisition IC that converts an analog voltage into a digital code. A successive-approximation register, or SAR, ADC performs conversion through a sequence of binary-weighted comparisons. In a simultaneous-sampling converter, all input channels use independent sample-and-hold circuits so that six channels retain the same sampling instant even though the internal conversion circuits process the signals in parallel pairs.
The ADS7864Y/2K supports a 500 kHz conversion rate, 12-bit resolution, and six fully differential analog inputs. Its parallel interface provides deterministic data transfer to digital logic, while the on-chip FIFO helps decouple sampling from downstream readout. The manufacturer describes a 2 microsecond total throughput time per channel, guaranteed no-missing-code operation, 80 dB common-mode rejection at 50 kHz, and approximately 50 mW low-power operation.
The differential input architecture reduces sensitivity to common-mode noise and is useful when sensors, transducers, or analog front ends generate centered signals. Three paired channels share a common-mode rejection benefit, while separate sample-and-hold paths preserve simultaneous timing across the complete input set. The converter is therefore suitable for phase-sensitive measurements where independent channel timing differences would distort the result.
Typical uses include three-phase motor analysis, vibration monitoring, industrial sensor acquisition, power-converter feedback, and multi-channel instrumentation. The 48-pin TQFP package provides enough pins for six differential inputs, power, reference, control signals, and a parallel data bus in a single surface-mount device.
Designers should preserve matched layout for each differential pair, keep analog and digital return currents separated, and treat the parallel interface timing as a high-speed signal-integrity task. Place bypass capacitors close to the supply pins and follow the manufacturer pin-description table when assigning every PFB-package connection.
This product page consolidates the manufacturer specifications, sourcing context, package details, and practical guidance needed to evaluate the ADS7864Y/2K for simultaneous data-acquisition designs.
এর জন্য ড্রপ-ইন বিকল্প ADS7864Y/2K — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
ADS7864Y/250
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
ADS7864YB/2K
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
ADS7864Y/2K সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য
| ADC Type | Dual 12-bit successive-approximation ADC |
| রেজোলিউশন | 12 bits |
| Analog Input Channels | 6 channels |
| Input Architecture | 3 fully differential input pairs |
| স্যাম্পলিং রেট | 500 kHz |
| Total Throughput Time Per Channel | 2 us |
| Effective Sampling Rate | 1 MHz |
| Common-Mode Rejection | 80 dB at 50 kHz |
| Power Consumption | 50 mW |
| Missing Code Performance | Guaranteed no missing codes |
| ইন্টারফেস | Parallel |
| FIFO | 6 entries |
| প্যাকেজ | 48-pin TQFP (PFB), 7 mm x 7 mm |
| মাউন্টিং টাইপ | Surface mount |
ADS7864Y/2K 48-pin tqfp (pfb), 7 mm x 7 mm পিন কনফিগারেশন গাইড
ADS7864Y/2K (48-pin tqfp (pfb), 7 mm x 7 mm প্যাকেজ)-এর পিন কনফিগারেশন। এই অ্যানালগ কম্পোনেন্টে ইনপুট, আউটপুট ও পাওয়ার সাপ্লাই পিন রয়েছে। অফসেট নাল, কম্পেনসেশন ও এনেবল পিন কনফিগারেশনের জন্য প্রস্তুতকারকের ডেটাশিট দেখুন। সিগন্যাল কন্ডিশনিং ও অ্যামপ্লিফায়ার সার্কিটের জন্য আদর্শ।
এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি ADS7864Y/2K.
দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।
সাধারণ ব্যবহার
ADS7864Y/2K এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Three-Phase Motor Analysis, Industrial Vibration Monitoring, Power Converter Feedback, Synchronized Sensor Acquisition, Audio and Communications Measurement, Test and Measurement Instrumentation.
Three-Phase Motor Analysis
The ADS7864Y/2K suits three-phase motor monitoring because it samples six fully differential inputs as three pairs at a common instant. Its 500 kHz conversion rate and 12-bit resolution provide useful resolution for phase current, phase voltage, position, and temperature feedback. By synchronizing the acquisition channels, the converter avoids sequential timing offsets that could distort phase relationships. The parallel interface supports deterministic transfer into a digital controller or acquisition logic, while differential inputs help reject switching noise from the motor drive. Keep each sensor pair closely matched and route the six analog channels as controlled, equal-length groups to preserve timing and common-mode performance.
সুপারিশকৃত
Industrial Vibration Monitoring
The ADS7864Y/2K is appropriate for vibration systems that need multiple sensor channels captured on one time base. Six simultaneous inputs allow accelerometer or velocity signals to be compared without sequential sampling error, which is important for phase and modal analysis. The 500 kHz rate and 12-bit conversion resolution support higher-frequency monitoring, while three differential pairs reduce susceptibility to common-mode interference in industrial environments. Use a low-noise sensor interface and route each differential pair away from switching power paths. The 6-entry FIFO can smooth interaction between conversion events and the parallel readout logic when the surrounding digital design cannot accept data continuously.
সুপারিশকৃত
Power Converter Feedback
The ADS7864Y/2K can acquire several feedback quantities from a power-conversion system in a synchronized measurement. Six differential inputs permit monitoring of paired voltage, current, or temperature signals, while simultaneous sampling helps maintain consistent timing between channels. The 500 kHz rate and 12-bit resolution are suitable for supervisory and control-loop measurements where the sampled signals must represent the same operating instant. Fully differential inputs are useful when the sensing front end is centered around a midpoint and when rejecting supply-related common-mode noise. Place the converter close to the analog sensing network, use quiet reference routing, and separate converter ground current from high-di/dt power-stage return paths.
সুপারিশকৃত
Synchronized Sensor Acquisition
The ADS7864Y/2K provides a compact solution when several industrial sensors must be sampled at the same time. Its three fully differential pairs accept six analog signals, while 12-bit resolution captures a useful balance between dynamic range and data throughput. The 2 microsecond per-channel throughput supports responsive monitoring without the complexity of a multiplexed input architecture. Differential wiring is particularly effective with bridge sensors, current monitors, and front ends that use a common bias. Match input impedance and amplifier bandwidth across channels where timing consistency matters, and use the on-chip FIFO to accommodate bursts of acquisition data without requiring a separate external FIFO.
সুপারিশকৃত
Audio and Communications Measurement
The ADS7864Y/2K can support communications, audio, or instrumentation test systems that require several waveforms to be captured with consistent timing. Six simultaneous differential channels make it possible to compare phase relationships, gains, or distortion-related quantities without sequential conversion offsets. The 500 kHz sampling rate is appropriate for many baseband and control-signal measurements, while 12-bit resolution provides a practical resolution-versus-throughput tradeoff. Differential inputs help reduce common-mode pickup from digital clocks and communication circuitry. Use low-impedance source networks, maintain symmetric routing for each pair, and keep the parallel data bus away from sensitive input nodes to minimize coupling into the acquisition result.
সুপারিশকৃত
Test and Measurement Instrumentation
The ADS7864Y/2K fits multi-channel test equipment that must acquire related voltages at a single time reference. Its 500 kHz rate, 12-bit resolution, and six fully differential inputs can simplify front-end design compared with a multiplexer-based converter. The parallel interface provides a direct path to FPGA or digital acquisition logic, while the 6-entry FIFO helps buffer short bursts. The 48-pin TQFP package integrates the analog inputs, reference, control logic, and digital interface into one surface-mount component. For accurate results, follow the manufacturer layout guidance, provide stable reference and supply decoupling, and separate analog input paths from clock and data-bus return currents.
সুপারিশকৃত
সুপারিশকৃত পণ্যের সারসংক্ষেপ
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা ADS7864Y/2K — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | ADS7864Y/250 | ADS7864YB/2K |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 48-TQFP (PFB, 7 mm x 7 mm) | 48-TQFP (PFB, 7 mm x 7 mm) | 48-TQFP (PFB, 7 mm x 7 mm) |
| Resolution | 12 bits | 12 bits | 12 bits |
| Sampling Rate | 500 kHz | 500 kHz | 500 kHz |
| Analog Input Channels | 6 channels | 6 channels | 6 channels |
| Input Architecture | 3 fully differential pairs | 3 fully differential pairs | 3 fully differential pairs |
| Interface | Parallel | Parallel | Parallel |
| Throughput Time Per Channel | 2 us | 2 us | 2 us |
| Common-Mode Rejection | 80 dB at 50 kHz | 80 dB at 50 kHz | 80 dB at 50 kHz |
| Power Consumption | 50 mW | 50 mW | 50 mW |
মূল পার্থক্যসমূহ
- Six channels retain a common sampling instant (বনামAD7864)
- Three fully differential analog input pairs (বনামAD7864)
- Family-consistent drop-in ordering alternatives (বনামADS7864YB/2K)
ডিজাইন নোট
Route every differential input pair together with matched impedance and similar trace lengths. Keep the six analog inputs away from the parallel data bus, clock traces, and high-current switching nodes. Place input-network components and bypass capacitors close to their associated converter pins. The manufacturer layout example should be used as the baseline because the 48-pin TQFP device combines six high-speed analog channels with a wide digital interface.
Treat the parallel interface as a synchronous high-speed bus. Establish a defined clock relationship, use the manufacturer's acquisition timing, and account for output delay, settling time, and board skew at the receiving logic. Series damping may be needed when ringing appears on long data lines. Keep the converter and interface circuitry on a quiet ground region so switching current from digital outputs does not disturb the fully differential input measurements.
Do not treat the six inputs as multiplexed measurements; their simultaneous-sampling behavior is a principal feature of the ADS7864Y/2K. Use the differential input common-mode range and analog input limits from the manufacturer datasheet when designing the source network. Check supply sequencing, reference stability, and conversion timing before fixing control timing in firmware. The Y/250 and YB/2K ordering codes should also be checked for their exact grade and packing requirements.
কমপ্লায়েন্স তথ্য
No explicit compliance declarations were identified in the manufacturer or distributor excerpts. Confirm RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status with Texas Instruments before using the component in a regulated production design.