Texas Instruments

ADS7864Y/2K - 12-Bit 6-Channel Simultaneous ADC | Texas Instruments

MPN: ADS7864Y/2K ✓ פעיל
48-pin TQFP (PFB), 7 mm x 7 mm Package
כמות הזמנה מינימלית: 1 |

ADS7864Y/2K סקירה

Texas Instruments ADS7864Y/2K is a 12-bit, 6-channel simultaneous-sampling analog-to-digital converter with 500 kHz sampling performance and fully differential inputs. The device contains two SAR ADCs and three differential input pairs, allowing related signals to be captured at the same instant for vibration, motor-control, and industrial monitoring systems. It is supplied in a 48-pin TQFP package measuring 7 mm by 7 mm.

An ADC is a data-acquisition IC that converts an analog voltage into a digital code. A successive-approximation register, or SAR, ADC performs conversion through a sequence of binary-weighted comparisons. In a simultaneous-sampling converter, all input channels use independent sample-and-hold circuits so that six channels retain the same sampling instant even though the internal conversion circuits process the signals in parallel pairs.

The ADS7864Y/2K supports a 500 kHz conversion rate, 12-bit resolution, and six fully differential analog inputs. Its parallel interface provides deterministic data transfer to digital logic, while the on-chip FIFO helps decouple sampling from downstream readout. The manufacturer describes a 2 microsecond total throughput time per channel, guaranteed no-missing-code operation, 80 dB common-mode rejection at 50 kHz, and approximately 50 mW low-power operation.

The differential input architecture reduces sensitivity to common-mode noise and is useful when sensors, transducers, or analog front ends generate centered signals. Three paired channels share a common-mode rejection benefit, while separate sample-and-hold paths preserve simultaneous timing across the complete input set. The converter is therefore suitable for phase-sensitive measurements where independent channel timing differences would distort the result.

Typical uses include three-phase motor analysis, vibration monitoring, industrial sensor acquisition, power-converter feedback, and multi-channel instrumentation. The 48-pin TQFP package provides enough pins for six differential inputs, power, reference, control signals, and a parallel data bus in a single surface-mount device.

Designers should preserve matched layout for each differential pair, keep analog and digital return currents separated, and treat the parallel interface timing as a high-speed signal-integrity task. Place bypass capacitors close to the supply pins and follow the manufacturer pin-description table when assigning every PFB-package connection.

This product page consolidates the manufacturer specifications, sourcing context, package details, and practical guidance needed to evaluate the ADS7864Y/2K for simultaneous data-acquisition designs.

חלופות תחליף ישיר עבור ADS7864Y/2K — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.

ADS7864Y/250

✅ Drop-In
📦 48-TQFP (PFB, 7 mm x 7 mm)
Same ADS7864 architecture and 48-pin TQFP footprint; ordering suffix differs by 0% in the identified 12-bit, 500 kHz, six-channel ratings

📋 חלופה להתייחסות (לא בקטלוג)

ADS7864YB/2K

✅ Drop-In
📦 48-TQFP (PFB, 7 mm x 7 mm)
Same ADS7864 architecture and 48-pin TQFP footprint; YB ordering suffix differs by 0% in the identified 12-bit, 500 kHz, six-channel ratings

📋 חלופה להתייחסות (לא בקטלוג)

ADS7864Y/2K דירוגים מרביים ומאפיינים חשמליים

ADC Type Dual 12-bit successive-approximation ADC
רזולוציה 12 bits
Analog Input Channels 6 channels
Input Architecture 3 fully differential input pairs
קצב דגימה 500 kHz
Total Throughput Time Per Channel 2 us
Effective Sampling Rate 1 MHz
Common-Mode Rejection 80 dB at 50 kHz
Power Consumption 50 mW
Missing Code Performance Guaranteed no missing codes
ממשק Parallel
FIFO 6 entries
מארז 48-pin TQFP (PFB), 7 mm x 7 mm
סוג הרכבה Surface mount

מדריך תצורת פינים של ADS7864Y/2K 48-pin tqfp (pfb), 7 mm x 7 mm

תצורת פינים עבור ADS7864Y/2K (מארזת 48-pin tqfp (pfb), 7 mm x 7 mm). רכיב אנלוגי זה כולל פיני כניסה, יציאה ואספקת מתח. יש לעיין בגיליון הנתונים של היצרן לתצורות פיני איפוס היסט, פיצוי והפעלה. אידיאלי למעגלי עיצוב אותות ומגברים.

תרשים פינים של מארזת 48-pin tqfp (pfb), 7 mm x 7 mm עבור ADS7864Y/2K

אין נתוני פריסת פינים מפורטים עבור ADS7864Y/2K.

עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.

יישומים טיפוסיים

ADS7864Y/2K מתאים עבור 6 יישוםs: Three-Phase Motor Analysis, Industrial Vibration Monitoring, Power Converter Feedback, Synchronized Sensor Acquisition, Audio and Communications Measurement, Test and Measurement Instrumentation.

🏭

Three-Phase Motor Analysis

The ADS7864Y/2K suits three-phase motor monitoring because it samples six fully differential inputs as three pairs at a common instant. Its 500 kHz conversion rate and 12-bit resolution provide useful resolution for phase current, phase voltage, position, and temperature feedback. By synchronizing the acquisition channels, the converter avoids sequential timing offsets that could distort phase relationships. The parallel interface supports deterministic transfer into a digital controller or acquisition logic, while differential inputs help reject switching noise from the motor drive. Keep each sensor pair closely matched and route the six analog channels as controlled, equal-length groups to preserve timing and common-mode performance.

🏭

Industrial Vibration Monitoring

The ADS7864Y/2K is appropriate for vibration systems that need multiple sensor channels captured on one time base. Six simultaneous inputs allow accelerometer or velocity signals to be compared without sequential sampling error, which is important for phase and modal analysis. The 500 kHz rate and 12-bit conversion resolution support higher-frequency monitoring, while three differential pairs reduce susceptibility to common-mode interference in industrial environments. Use a low-noise sensor interface and route each differential pair away from switching power paths. The 6-entry FIFO can smooth interaction between conversion events and the parallel readout logic when the surrounding digital design cannot accept data continuously.

⚡

Power Converter Feedback

The ADS7864Y/2K can acquire several feedback quantities from a power-conversion system in a synchronized measurement. Six differential inputs permit monitoring of paired voltage, current, or temperature signals, while simultaneous sampling helps maintain consistent timing between channels. The 500 kHz rate and 12-bit resolution are suitable for supervisory and control-loop measurements where the sampled signals must represent the same operating instant. Fully differential inputs are useful when the sensing front end is centered around a midpoint and when rejecting supply-related common-mode noise. Place the converter close to the analog sensing network, use quiet reference routing, and separate converter ground current from high-di/dt power-stage return paths.

🧩

Synchronized Sensor Acquisition

The ADS7864Y/2K provides a compact solution when several industrial sensors must be sampled at the same time. Its three fully differential pairs accept six analog signals, while 12-bit resolution captures a useful balance between dynamic range and data throughput. The 2 microsecond per-channel throughput supports responsive monitoring without the complexity of a multiplexed input architecture. Differential wiring is particularly effective with bridge sensors, current monitors, and front ends that use a common bias. Match input impedance and amplifier bandwidth across channels where timing consistency matters, and use the on-chip FIFO to accommodate bursts of acquisition data without requiring a separate external FIFO.

🌐

Audio and Communications Measurement

The ADS7864Y/2K can support communications, audio, or instrumentation test systems that require several waveforms to be captured with consistent timing. Six simultaneous differential channels make it possible to compare phase relationships, gains, or distortion-related quantities without sequential conversion offsets. The 500 kHz sampling rate is appropriate for many baseband and control-signal measurements, while 12-bit resolution provides a practical resolution-versus-throughput tradeoff. Differential inputs help reduce common-mode pickup from digital clocks and communication circuitry. Use low-impedance source networks, maintain symmetric routing for each pair, and keep the parallel data bus away from sensitive input nodes to minimize coupling into the acquisition result.

🔧

Test and Measurement Instrumentation

The ADS7864Y/2K fits multi-channel test equipment that must acquire related voltages at a single time reference. Its 500 kHz rate, 12-bit resolution, and six fully differential inputs can simplify front-end design compared with a multiplexer-based converter. The parallel interface provides a direct path to FPGA or digital acquisition logic, while the 6-entry FIFO helps buffer short bursts. The 48-pin TQFP package integrates the analog inputs, reference, control logic, and digital interface into one surface-mount component. For accurate results, follow the manufacturer layout guidance, provide stable reference and supply decoupling, and separate analog input paths from clock and data-bus return currents.

What is the ADS7864Y/2K?
The ADS7864Y/2K is a 12-bit, six-channel simultaneous-sampling ADC from Texas Instruments. According to the manufacturer product page, it contains two SAR converters, supports a 500 kHz sampling rate, and provides three fully differential input pairs in a 48-pin TQFP package. It is designed for acquisition systems that require multiple analog signals to be captured at the same time.
How many channels and bits does ADS7864Y/2K have?
The ADS7864Y/2K provides six analog input channels with 12-bit resolution. The six channels are organized as three fully differential pairs, and the device uses two SAR conversion circuits to process those pairs in parallel. This organization preserves common timing across all six sampled inputs while maintaining a 500 kHz conversion rate.
What is the sampling rate of ADS7864Y/2K?
The ADS7864Y/2K supports 500 kHz sampling performance for each conversion channel. The manufacturer datasheet also identifies a 2 microsecond total throughput time per channel and a 1 MHz effective sampling rate across the six-channel device. These figures make it suitable for high-speed multichannel instrumentation and synchronized signal capture.
Where can I download the ADS7864Y/2K datasheet PDF?
The official ADS7864 datasheet PDF is available from the Texas Instruments product page at https://www.ti.com/lit/gpn/ads7864. It is the primary document for electrical characteristics, PFB pin descriptions, application information, and recommended operating conditions. Use the package pin table to assign signals because the public search material does not enumerate every connector name.
Where can I find the ADS7864Y/2K pinout?
The ADS7864Y/2K pinout is found in the pin-description section of the manufacturer ADS7864 datasheet. The component uses a 48-pin TQFP PFB package, so the package has 48 numbered positions. Use that table for power, analog inputs, reference connections, control signals, and the parallel digital interface when assigning PCB nets.
Does ADS7864Y/2K support simultaneous sampling?
Yes, the ADS7864Y/2K supports simultaneous sampling across all six analog channels. According to the manufacturer product description, each input is maintained by a dedicated sample-and-hold stage before conversion. This is important for phase, vibration, and motor measurements because the captured values share a common sampling instant rather than being sampled sequentially.
What is the input architecture of ADS7864Y/2K?
The ADS7864Y/2K accepts six fully differential inputs organized into three pairs. Differential sampling improves rejection of common-mode noise and is particularly useful with sensor and transducer outputs centered around a bias voltage. The manufacturer reports 80 dB common-mode rejection at 50 kHz, a useful figure when evaluating noise performance near the upper channel bandwidth.
What are the key specifications engineers should know about ADS7864Y/2K?
The key ADS7864Y/2K specifications are 12-bit resolution, six simultaneous inputs, a 500 kHz sampling rate, 2 microsecond throughput per channel, a parallel interface, and approximately 50 mW operation. Texas Instruments also identifies three fully differential input pairs, a 6-entry FIFO, guaranteed no-missing-code performance, and 80 dB common-mode rejection at 50 kHz.
When should I choose ADS7864Y/2K for motor control?
Choose the ADS7864Y/2K when a motor-control system must capture several related analog channels at a common instant. Its six fully differential inputs support current, voltage, position, or temperature feedback, while the 12-bit resolution and 500 kHz rate provide useful dynamic range and timing. Differential pairs can also reduce common-mode pickup from switching power stages.
Is ADS7864Y/2K suitable for vibration monitoring?
The ADS7864Y/2K is suitable for vibration monitoring that requires synchronized multichannel measurements. Simultaneous sampling prevents phase error between channels, and the 500 kHz rate supports analysis of higher-frequency mechanical behavior. The three differential pairs also help reject noise when accelerometers or other transducers use balanced signal wiring.
What can replace the ADS7864Y/2K?
The ADS7864Y/250 and ADS7864YB/2K are the closest identified alternatives because they belong to the ADS7864 family and use the same 48-pin TQFP PFB package. ADS7864Y/250 differs in its ordering suffix, while ADS7864YB/2K represents a distinct ordering variant. Confirm temperature grade, acquisition timing, interface behavior, and production ordering requirements before replacement.
Is ADS7864Y/250 the same as ADS7864Y/2K?
The ADS7864Y/250 is not the exact same ordering code as the ADS7864Y/2K, although both are ADS7864 family devices. Both are associated with the 500 kHz, 12-bit, six-channel simultaneous-sampling architecture and a 48-pin TQFP package. The suffix difference can encode ordering and temperature or packaging information, so verify those requirements before treating it as a substitution.
What is the best Analog Devices equivalent for ADS7864Y/2K?
The AD7864 is the closest identified Analog Devices candidate, but it is not a verified pin-to-pin drop-in replacement for the ADS7864Y/2K. The AD7864 provides four simultaneous-sampling channels rather than six, while the ADS7864Y/2K also uses three differential pairs and a 48-pin TQFP. A board-level or footprint-compatible substitute could not be confirmed.
Where can I buy ADS7864Y/2K online?
Use the Request a Quote form on this page to ask for ADS7864Y/2K pricing, current inventory, and order handling. The form is the appropriate route for commercial inquiries because quote status and availability can change quickly. The manufacturer order code is ADS7864Y/2K, and the component is identified in a 48-pin TQFP PFB package.
What is the price of ADS7864Y/2K?
Current ADS7864Y/2K pricing is handled through the Request a Quote form on this page. The form supports quantity-specific sourcing, current stock confirmation, and lead-time requests without embedding a stale price in the technical description. Provide the required quantity, package suffix, and target delivery date when requesting a quotation.
Is ADS7864Y/2K in stock and what is its lead time?
Use the Request a Quote form on this page to confirm current ADS7864Y/2K stock, minimum order quantity, and production lead time. Inventory can vary by package suffix and regional fulfillment conditions, so it should be checked for each order rather than assumed from a catalog listing. The exact ordering code to submit is ADS7864Y/2K.

נתוני עזר הנדסיים עבור ADS7864Y/2K — השוואה, הנחיות תכנון ומידע על תאימות.

מדריך בחירה

Choose the ADS7864Y/2K when the design requires six analog channels to be sampled simultaneously and the system can accommodate a parallel interface in a 48-pin TQFP. Its three differential pairs, 500 kHz rate, and 12-bit resolution are well suited to synchronized motor, vibration, power-control, and instrumentation measurements. Select ADS7864Y/250 when that exact ordering suffix matches the required grade and packaging while preserving the same family architecture. Choose ADS7864YB/2K when its ordering characteristics satisfy the production requirement. The Analog Devices AD7864 offers a related simultaneous-sampling function but has four channels and a different package, so it should be treated as a redesign option rather than a drop-in substitute. Before ordering, confirm reference voltage, supply range, acquisition timing, FIFO behavior, temperature grade, and lifecycle requirements against the manufacturer datasheet.

השוואה עם חלופות

פרמטר מוצר זה ADS7864Y/250 ADS7864YB/2K
Brand Texas Instruments Texas Instruments Texas Instruments
Package 48-TQFP (PFB, 7 mm x 7 mm) 48-TQFP (PFB, 7 mm x 7 mm) 48-TQFP (PFB, 7 mm x 7 mm)
Resolution 12 bits 12 bits 12 bits
Sampling Rate 500 kHz 500 kHz 500 kHz
Analog Input Channels 6 channels 6 channels 6 channels
Input Architecture 3 fully differential pairs 3 fully differential pairs 3 fully differential pairs
Interface Parallel Parallel Parallel
Throughput Time Per Channel 2 us 2 us 2 us
Common-Mode Rejection 80 dB at 50 kHz 80 dB at 50 kHz 80 dB at 50 kHz
Power Consumption 50 mW 50 mW 50 mW

מבדילים עיקריים

  • Six channels retain a common sampling instant (לעומתAD7864)
  • Three fully differential analog input pairs (לעומתAD7864)
  • Family-consistent drop-in ordering alternatives (לעומתADS7864YB/2K)

הערות תכנון

Route every differential input pair together with matched impedance and similar trace lengths. Keep the six analog inputs away from the parallel data bus, clock traces, and high-current switching nodes. Place input-network components and bypass capacitors close to their associated converter pins. The manufacturer layout example should be used as the baseline because the 48-pin TQFP device combines six high-speed analog channels with a wide digital interface.

Treat the parallel interface as a synchronous high-speed bus. Establish a defined clock relationship, use the manufacturer's acquisition timing, and account for output delay, settling time, and board skew at the receiving logic. Series damping may be needed when ringing appears on long data lines. Keep the converter and interface circuitry on a quiet ground region so switching current from digital outputs does not disturb the fully differential input measurements.

Do not treat the six inputs as multiplexed measurements; their simultaneous-sampling behavior is a principal feature of the ADS7864Y/2K. Use the differential input common-mode range and analog input limits from the manufacturer datasheet when designing the source network. Check supply sequencing, reference stability, and conversion timing before fixing control timing in firmware. The Y/250 and YB/2K ordering codes should also be checked for their exact grade and packing requirements.

מידע על תאימות

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
נטול עופרת
Unknown
נטול הלוגנים
Unknown
מינרלים של סכסוך
Unknown

No explicit compliance declarations were identified in the manufacturer or distributor excerpts. Confirm RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status with Texas Instruments before using the component in a regulated production design.

הנתונים אומתו בתאריך: 2026-11-18 — נתונים אומתו ונערכו על ידי צוות הנדסת הרכיבים של XAIPART

חיפושים קשורים

ads7864y datasheet ADS7864Y/2K datasheet ADS7864Y/2K datasheet pdf ADS7864Y/2K pinout ADS7864Y/2K 48-TQFP ADS7864Y/2K 500kHz 12-bit ADS7864Y/2K simultaneous sampling ADS7864Y/2K replacement ADS7864Y/2K equivalent ADS7864Y/2K price ADS7864Y/2K stock ADS7864Y/2K vs AD7864

רכיבים ומונחים קשורים

Texas Instruments ADS7864Y/2K ADS7864Y/250 ADS7864YB/2K AD7864 analog-to-digital converter ADC successive-approximation register SAR ADC simultaneous-sampling ADC fully differential input 12-bit resolution 500 kHz sampling rate common-mode rejection parallel interface 6-entry FIFO 48-pin TQFP PFB package surface-mount device industrial instrumentation motor-control measurement vibration monitoring sample-and-hold amplifier data acquisition
בקשת הצעת מחיר מהירה
מלא את כל הפרטים — צוות המכירות שלנו יגיב תוך 24 שעות
מספר חלק יצרן מארז QTY מחיר יעד סה"כ
✓
הצעת המחיר נשלחה!

נשיב לדוא"ל שלך בתוך 24 שעות

1
בקשת הצעת מחיר נשלחה
2
הצעת מחיר התקבלה
3
ההזמנה בוצעה
4
תשלום
5
נשלח
6
נמסר
צפה בפרטי בקשת הצעת המחיר