ATSAMD20E14B-MU - 48MHz Cortex-M0+ MCU | Microchip
MPN: ATSAMD20E14B-MU ✓ সক্রিয়ATSAMD20E14B-MU সারাংশ
A microcontroller is a programmable control IC that combines a processor core, memory, and peripherals on one semiconductor device. The Cortex-M0+ core provides a compact instruction set suited to real-time control, while the ATSAMD20E14 family integrates flash, SRAM, communication interfaces, analog conversion functions, and timing resources into a low-power embedded platform.
Key device characteristics include a maximum operating frequency of 48 MHz, 16 KB of flash, and 2 KB of SRAM. The 1.6 V to 3.6 V operating range supports low-voltage 3.3 V systems, while the industrial-temperature B grade targets applications requiring operation across an extended commercial temperature range. The 32-VFQFN package also provides an exposed thermal pad that improves heat dissipation when the device operates at higher clock frequencies or with active peripherals.
The ATSAMD20E14 belongs to Microchip's SAM D20 series and is based on the ARM Cortex-M0+ architecture. Its compact memory configuration is suitable for protocol translation, data acquisition, basic control loops, and auxiliary embedded tasks where a larger application controller is unnecessary. The SAM D20 family also supports peripherals including a 12-bit ADC, a 10-bit DAC, PTC temperature sensing, and an RTC, according to the family datasheet description.
Typical uses include home automation, consumer products, metering equipment, and industrial controls. A metering design can use the ADC for analog sensor inputs, the RTC for timekeeping, and serial interfaces for communicating with a display or upstream controller. In a smart-home node, low-power operation and compact packaging support cost- and space-constrained control boards.
PCB design should follow the manufacturer land pattern and pin-description tables for the 32-VFQFN package. Place decoupling capacitors close to the supply pins, connect the exposed pad to the appropriate ground plane, and preserve clearances around the package perimeter. Validate signal routing, clock stability, analog grounding, and thermal performance across the intended voltage and temperature ranges.
This product summary combines the device architecture, memory configuration, package details, sourcing context, and practical implementation considerations needed to plan an ATSAMD20E14B-MU-based design. It also highlights the distinctions to review before approving a replacement or transferring the circuit to another SAM D20 member.
এর জন্য ড্রপ-ইন বিকল্প ATSAMD20E14B-MU — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
এই সিরিজের ভ্যারিয়েন্ট
একই সিরিজের মডেল যেগুলো drop-in compatible ATSAMD20E14B-MU (একই form factor এবং footprint) — পার্থক্য রয়েছে Flash Memory, Package.
ATSAMD20E14B-MUT
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →ATSAMD20E14B-MNT
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
ATSAMD20E14B-MU সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য
| Processor Core | ARM Cortex-M0+ |
| Architecture | 32-bit |
| Maximum CPU Frequency | 48 MHz |
| Flash Memory | 16 KB (16K x 8 bits) |
| SRAM | 2 KB |
| অপারেটিং সাপ্লাই ভোল্টেজ | 1.6 V to 3.6 V |
| Nominal Supply Voltage | 3.3 V |
| Device Type | Low-power flash microcontroller |
| Product Series | SAM D20E |
| প্যাকেজ | 32-VFQFN, 5 x 5 mm, exposed pad |
| মাউন্টিং টাইপ | Surface mount |
| Temperature Grade | Industrial temperature grade |
| ADC Resolution | 12 bits |
| DAC Resolution | 10 bits |
| Temperature Sensing | 256-channel PTC support |
| Real-Time Clock | Supported |
| Green Product | Yes |
ATSAMD20E14B-MU 32-vfqfn, 5 x 5 mm, exposed pad পিন কনফিগারেশন গাইড
ATSAMD20E14B-MU (32-vfqfn, 5 x 5 mm, exposed pad প্যাকেজ)-এর পিন কনফিগারেশন। এই ডিজিটাল IC-তে GPIO, কমিউনিকেশন ইন্টারফেস (UART, SPI, I2C) এবং পাওয়ার পিন রয়েছে। বিকল্প পিন ফাংশন ও কনফিগারেশন অপশনের জন্য প্রস্তুতকারকের ডেটাশিট দেখুন। এমবেডেড সিস্টেম ডিজাইন ও PCB লেআউটের জন্য অপরিহার্য।
এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি ATSAMD20E14B-MU.
দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।
সাধারণ ব্যবহার
ATSAMD20E14B-MU এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Industrial Metering Controller, Smart Home Sensor Node, Consumer Appliance Control, Home Automation Gateway Module, Battery-Powered Data Logger, Portable Medical Sensor Interface.
Industrial Metering Controller
The ATSAMD20E14B-MU fits compact metering controllers where a 48 MHz Cortex-M0+ core can perform control and measurement functions without a larger memory footprint. Its 12-bit ADC supports analog sensor conditioning, while the integrated 10-bit DAC can provide basic analog control or test signals. The 16 KB flash and 2 KB SRAM place explicit limits on application code and working data, so the firmware should use compact drivers and an RTOS only when its memory overhead is justified. The 1.6 V to 3.6 V operating range supports 3.3 V meter electronics, and the 32-VFQFN footprint simplifies dense, low-cost meter boards.
সুপারিশকৃত
Smart Home Sensor Node
The ATSAMD20E14B-MU can act as the local controller for a connected sensor node that gathers measurements and manages low-power peripherals. Its 48 MHz Cortex-M0+ core provides responsive handling of sensor data and communication interrupts, while 16 KB of flash suits a focused firmware image rather than a feature-rich gateway. The integrated ADC and PTC temperature-sensing support reduce external signal-conditioning requirements. Because the 5 x 5 mm VFQFN package leaves little room for excess decoupling or routing errors, place bypass capacitors directly beside the supply pins and route analog inputs away from switching-node currents.
সুপারিশকৃত
Consumer Appliance Control
ATSAMD20E14B-MU is appropriate for a small consumer appliance controller where deterministic low-cost control matters more than large application storage. The 32-bit Cortex-M0+ processor executes motor, button, and interface logic at up to 48 MHz, and the 2 KB SRAM is sufficient for compact state machines and short communication buffers. A 3.3 V system architecture aligns with the device's 1.6 V to 3.6 V operating range. Designers should reserve flash space for calibration and firmware updates, and should use the exposed pad as a deliberate thermal path rather than leaving it isolated during board layout.
সুপারিশকৃত
Home Automation Gateway Module
The ATSAMD20E14B-MU can serve as a peripheral or leaf controller within a home-automation system, coordinating inputs, local outputs, and a low-speed communications interface. Its 48 MHz processing rate supports event handling and protocol routines, while the compact 32-VFQFN package allows placement alongside a radio or communications component. The limited 16 KB flash and 2 KB SRAM favor a focused gateway role rather than local data aggregation or graphics. Power-budget design should include the MCU, analog peripherals, and any attached radio because the MCU's own operating range does not determine the accuracy of peripheral measurements.
সুপারিশকৃত
Battery-Powered Data Logger
ATSAMD20E14B-MU can support a compact battery-powered logger when its low-power operating modes and on-chip memory are sufficient for the application. The 48 MHz Cortex-M0+ core can timestamp and process samples between sleep intervals, while the ADC enables direct connection to suitable analog sensors. With only 16 KB of flash and 2 KB of SRAM, buffered data should normally be transferred rather than accumulated indefinitely. Validate sleep-mode current, wake-up behavior, and analog accuracy at the minimum system voltage, and isolate analog inputs when the device is inactive to avoid collecting unintended sensor bias.
সুপারিশকৃত
Portable Medical Sensor Interface
The ATSAMD20E14B-MU can be evaluated for a portable medical-sensor interface where compactness, low supply voltage, and deterministic embedded control are important. Its 12-bit ADC provides a starting point for low-bandwidth physiological or diagnostic sensor conditioning, while the 10-bit DAC can generate low-level excitation or test signals. The 16 KB flash and 2 KB SRAM require careful partitioning for safety checks, acquisition routines, and communications. For medical use, complete the appropriate risk assessment, validate input leakage and accuracy, and confirm the applicable regulatory requirements independently of the component's RoHS status.
সুপারিশকৃত
সুপারিশকৃত পণ্যের সারসংক্ষেপ
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা ATSAMD20E14B-MU — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | ATSAMD20E14B-MUT | ATSAMD20E14B-MNT |
|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 32-VFQFN (5x5) Exposed Pad | 32-VFQFN (5x5) Exposed Pad | 32-terminal package; drawing requires verification |
| Processor Core | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ |
| Maximum CPU Frequency | 48 MHz | 48 MHz | 48 MHz |
| Flash Memory | 16 KB | 16 KB | 16 KB |
| SRAM | 2 KB | 2 KB | 2 KB |
| Operating Supply Voltage | 1.6 V to 3.6 V | 1.6 V to 3.6 V | 1.6 V to 3.6 V |
| ADC Resolution | 12 bits | 12 bits | 12 bits |
| DAC Resolution | 10 bits | 10 bits | 10 bits |
মূল পার্থক্যসমূহ
- Directly preserves the documented SAM D20E configuration (বনামATSAMD20E14B-MUT)
- Compact 16 KB flash configuration supports focused embedded firmware (বনামATSAMD20E14B-MNT)
- Integrated analog resources reduce external support components (বনামATSAMD20E14B-MUT)
ডিজাইন নোট
Use the manufacturer land pattern for the 32-VFQFN 5 x 5 mm package and place all required bypass capacitors adjacent to their associated supply pins. Keep analog inputs and references on the quiet side of the board, away from switching power paths and high-current return currents. Because the exposed pad is part of the thermal and electrical footprint, connect it to the recommended ground structure and thermal vias rather than treating it as spare area.
Design the 3.3 V supply path so its voltage remains between 1.6 V and 3.6 V under startup, load transients, and minimum operating conditions. Check the maximum total current from the MCU and attached peripherals against the regulator's capacity and dropout behavior. Account for inrush from external loads that may be switched around the MCU, and use the family's low-power modes deliberately when designing battery-powered applications.
Estimate the ATSAMD20E14B-MU's temperature rise at the highest expected clock rate and peripheral activity, then add that rise to the maximum ambient temperature. The 32-VFQFN exposed pad lowers junction temperature only when it is connected to an effective copper and via network. Validate thermal performance on the final board because PCB copper area, layer count, airflow, adjacent heat sources, and package orientation can materially change the result.
Do not assume that every ATSAMD20E14 orderable code has the same footprint or temperature rating. Verify the package drawing, exposed-pad connection, pin multiplexing, flash configuration, and maximum clock behavior against the exact MPN before releasing PCB artwork or production firmware. With only 16 KB of flash and 2 KB of SRAM, also check bootloader, stack, interrupt-vector, and application-code requirements before committing to the device.
কমপ্লায়েন্স তথ্য
The device is identified as a green product. RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status require confirmation from current manufacturer or distributor documentation.