ATTINY13A-MMF - 20MHz 1KB Flash 8-Bit AVR | Microchip
MPN: ATTINY13A-MMF ✓ সক্রিয়ATTINY13A-MMF সারাংশ
An 8-bit microcontroller is a compact digital controller that executes instructions from nonvolatile program memory and uses general-purpose input/output pins to monitor inputs or control external circuits. The ATTINY13A belongs to the TinyAVR family within the broader hierarchy of 8-bit AVR microcontrollers, embedded processors, and semiconductor devices. Its small memory footprint makes it appropriate for focused control tasks rather than complex graphical, networking, or high-volume data-processing applications.
The device combines a 20 MHz maximum clock with single-cycle instruction execution, enabling throughput approaching 1 MIPS per MHz and up to 20 MIPS. Four 10-bit ADC channels provide basic analog measurement, while integrated EEPROM preserves calibration, configuration, or identification data without external memory. The manufacturer identifies the family as picoPower architecture, emphasizing efficient operation in compact embedded products.
Programming is supported through In-Circuit Serial Programming and the MPLAB Snap debug interface. The ATTINY13A platform is commonly developed with Microchip toolchains and third-party AVR environments, making it useful for prototypes, simple control boards, timers, and small sensor interfaces. The 1 KB program memory requires careful code-size budgeting, especially when analog control, communication routines, and application logic are combined.
Typical designs use the ATTINY13A-MMF in compact control modules, LED drivers, simple timers, sensor interfaces, and inexpensive USB-to-serial projects. Its 20 MHz operating capability allows responsive control and straightforward timer-based sequencing, while the 10-MLP package supports space-constrained PCB layouts. Programming requires a compatible connector and ISP-compatible programmer or bootloader arrangement.
Designers should pay close attention to power sequencing, decoupling, exposed-pad layout, and programming access in the 10-MLP footprint. Keep the ADC reference and sensitive signal routing away from fast-switching nodes, and confirm the selected package land pattern before release. This page combines manufacturer specifications, sourcing information, package guidance, practical application notes, and a focused replacement analysis for engineers evaluating the ATTINY13A-MMF.
এর জন্য ড্রপ-ইন বিকল্প ATTINY13A-MMF — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
এই পণ্যের জন্য কোনো ড্রপ-ইন বিকল্প পাওয়া যায়নি।
বিকল্প অনুরোধ করুনATTINY13A-MMF সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য
| Product Type | 8-bit AVR microcontroller |
| সর্বোচ্চ ক্লক ফ্রিকোয়েন্সি | 20 MHz |
| Maximum Throughput | 20 MIPS at 20 MHz |
| Flash Memory | 1 KB |
| Flash Memory Organization | 512 x 16 bits |
| EEPROM | 64 bytes |
| SRAM | 64 bytes |
| Register File | 32 bytes |
| ADC Resolution | 10 bits |
| ADC Channels | 4 channels |
| Operating Voltage | 1.8 V to 5.5 V |
| Architecture | AVR enhanced RISC |
| Architecture Family | tinyAVR |
| Low-Power Technology | picoPower |
| প্যাকেজ | 10-MLP (3 x 3 mm) |
| মাউন্টিং টাইপ | Surface mount |
| Programming Interface | In-Circuit Serial Programming (ICSP) |
| Debug Interface | MPLAB Snap |
ATTINY13A-MMF 10-mlp (3 x 3 mm) পিন কনফিগারেশন গাইড
ATTINY13A-MMF (10-mlp (3 x 3 mm) প্যাকেজ)-এর পিন কনফিগারেশন। এই ডিজিটাল IC-তে GPIO, কমিউনিকেশন ইন্টারফেস (UART, SPI, I2C) এবং পাওয়ার পিন রয়েছে। বিকল্প পিন ফাংশন ও কনফিগারেশন অপশনের জন্য প্রস্তুতকারকের ডেটাশিট দেখুন। এমবেডেড সিস্টেম ডিজাইন ও PCB লেআউটের জন্য অপরিহার্য।
এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি ATTINY13A-MMF.
দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।
সাধারণ ব্যবহার
ATTINY13A-MMF এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Compact Sensor Interface, LED Sequencing and Lighting Control, Timer and Duty-Cycle Controller, Battery-Powered Embedded Control, USB-to-Serial Programmer Board, Small Consumer Appliance Controller.
Compact Sensor Interface
The ATTINY13A-MMF fits small analog-monitoring modules because it combines four 10-bit ADC channels with a 20 MHz AVR core in a 3 x 3 mm MLP package. The controller can sample sensors, apply threshold logic, and update an indicator or actuator without requiring a larger processor. Keep the application within the 1 KB flash and 64-byte SRAM limits, reference ADC decisions to the manufacturer’s pin and electrical tables, and isolate analog routing from switching nodes. Its picoPower architecture also supports low-power operation when the duty cycle permits sleep modes.
সুপারিশকৃত
LED Sequencing and Lighting Control
ATTINY13A-MMF is well suited to compact LED sequencers, status indicators, and low-current lighting controllers where board area is constrained. A 20 MHz clock supports precise timer-based updates, while the 1 KB program memory is sufficient for compact state machines and pulse patterns. Drive LEDs through suitable transistor or driver circuitry rather than overloading GPIO current limits, and account for PWM resolution when planning dimming behavior. The 10-MLP footprint also requires careful exposed-pad and paste-pattern review before production.
সুপারিশকৃত
Timer and Duty-Cycle Controller
The ATTINY13A-MMF can implement compact timers, pulse generators, duty-cycle controls, and scheduled output systems using its 20 MHz AVR processing capability. Because AVR instructions execute in a single clock cycle, the device can deliver throughput approaching 1 MIPS per MHz, which simplifies precise event handling and short interrupt routines. Favor timer hardware for repetitive timing and reserve CPU cycles for control logic. Validate startup, rollover, and interrupt behavior across the 1.8 V to 5.5 V operating range before finalizing a production design.
সুপারিশকৃত
Battery-Powered Embedded Control
ATTINY13A-MMF is appropriate for small battery-powered controls because the TinyAVR device combines picoPower operation with a low 1.8 V minimum supply voltage. A compact application can measure an analog condition, operate an output, and spend most of its time in a low-power state. Calculate the average current from active and sleep-mode behavior in the manufacturer datasheet, and size the external regulator or battery for peak loads. Firmware should minimize continuous ADC use and disable unused peripherals to preserve the intended power advantage.
সুপারিশকৃত
USB-to-Serial Programmer Board
ATTINY13A-MMF can serve as the target microcontroller in a compact USB-to-serial programmer board because it supports In-Circuit Serial Programming and is recognized by the MicroCore Arduino hardware package. The device also supports MPLAB Snap programming and debugging, providing familiar development paths. The 1 KB program-memory limit favors direct ISP operation or a very small bootloader in tightly constrained boards. Preserve the ISP signal access, add reliable reset and programming connectors, and verify that the USB-to-UART interface operates at the selected target voltage.
সুপারিশকৃত
Small Consumer Appliance Controller
ATTINY13A-MMF can manage a simple appliance or accessory controller with a small state machine, button inputs, and one or more timed outputs. Its 64 bytes of SRAM and 1 KB flash are adequate for focused logic but not for extensive menu systems or complex protocols. Use the ADC only when the control function genuinely requires analog measurement, and select external drive components for loads beyond GPIO capability. For designs expected to grow in functions, firmware size, or I/O count, select a larger TinyAVR early to avoid a package and board redesign.
সুপারিশকৃত
সুপারিশকৃত পণ্যের সারসংক্ষেপ
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা ATTINY13A-MMF — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য |
|---|---|
| Package | 10-MLP (3 x 3 mm) |
| Brand | Microchip Technology |
| Core Processor | 8-bit AVR |
| Maximum Clock Frequency | 20 MHz |
| Flash Memory | 1 KB |
| EEPROM | 64 bytes |
| SRAM | 64 bytes |
| ADC | 4-channel, 10-bit |
| Operating Voltage | 1.8 V to 5.5 V |
| Programming Interface | In-Circuit Serial Programming |
মূল পার্থক্যসমূহ
- High processing throughput in a compact 3 x 3 mm footprint (বনামATTINY13A-SH)
- Integrated analog conversion without an external ADC (বনামATTINY13A-SSUR)
- Useful resource level for focused embedded control (বনামATTINY20-MMHR)
ডিজাইন নোট
Design the 10-MLP land pattern directly from the manufacturer package drawing and confirm whether the exposed pad is electrically connected, solderable, or both. The canonical package-visualization library does not include an MLP-10 entry, so use the datasheet drawing as the controlling PCB footprint source. Place the decoupling capacitor close to the supply and ground pins, keep the exposed-pad geometry unobstructed, and confirm the assembly stencil and solder profile with the selected board manufacturer.
Keep the four ADC inputs on quiet, short traces and route them away from switching nodes, crystal or clock circuitry, and high-current outputs. If the ADC reference uses an external source, give that net a compact low-impedance layout and follow the manufacturer’s input-impedance recommendations. The ATTINY13A-MMF can execute up to 20 MIPS, so fast digital edges can couple into analog measurements even though the device itself has a 20 MHz maximum operating frequency.
Plan the power tree around the 1.8 V to 5.5 V operating range and ensure that the programmer logic, pull-ups, and connected peripherals use compatible voltage levels. Place local supply and ground capacitors at the device pins using the values and placement guidance in the manufacturer datasheet. Estimate average power from active-current, sleep-current, and duty-cycle values rather than using the maximum-clock current alone, particularly for battery-powered designs.
Do not treat related ATTINY13A package suffixes as interchangeable. ATTINY13A-SH and ATTINY13A-SSUR use different package formats from the ATTINY13A-MMF MLP device, so substituting them requires a new footprint and assembly process. Also monitor the 1 KB flash limit during toolchain selection, remove unused library code, and verify the configured clock and fuse settings against the operating voltage before programming production units.
কমপ্লায়েন্স তথ্য
No explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations were present in the manufacturer or distributor material.