Microchip Technology

ATTINY13A-MMF - 20MHz 1KB Flash 8-Bit AVR | Microchip

MPN: ATTINY13A-MMF ✓ सक्रिय
1.8 V to 5.5 V Vdss 10-MLP (3 x 3 mm) Package 20 MHz Speed 1 KB Memory
न्यूनतम ऑर्डर मात्रा: 1 |

ATTINY13A-MMF अवलोकन

The Microchip Technology ATTINY13A-MMF is a low-power, picoPower 8-bit AVR microcontroller operating at up to 20 MHz, with 1 KB of flash memory and a 10-MLP 3x3 mm package. It supports a 1.8 V to 5.5 V operating range and integrates 64 bytes of EEPROM, 64 bytes of SRAM, a 32-byte register file, and a four-channel 10-bit ADC.

An 8-bit microcontroller is a compact digital controller that executes instructions from nonvolatile program memory and uses general-purpose input/output pins to monitor inputs or control external circuits. The ATTINY13A belongs to the TinyAVR family within the broader hierarchy of 8-bit AVR microcontrollers, embedded processors, and semiconductor devices. Its small memory footprint makes it appropriate for focused control tasks rather than complex graphical, networking, or high-volume data-processing applications.

The device combines a 20 MHz maximum clock with single-cycle instruction execution, enabling throughput approaching 1 MIPS per MHz and up to 20 MIPS. Four 10-bit ADC channels provide basic analog measurement, while integrated EEPROM preserves calibration, configuration, or identification data without external memory. The manufacturer identifies the family as picoPower architecture, emphasizing efficient operation in compact embedded products.

Programming is supported through In-Circuit Serial Programming and the MPLAB Snap debug interface. The ATTINY13A platform is commonly developed with Microchip toolchains and third-party AVR environments, making it useful for prototypes, simple control boards, timers, and small sensor interfaces. The 1 KB program memory requires careful code-size budgeting, especially when analog control, communication routines, and application logic are combined.

Typical designs use the ATTINY13A-MMF in compact control modules, LED drivers, simple timers, sensor interfaces, and inexpensive USB-to-serial projects. Its 20 MHz operating capability allows responsive control and straightforward timer-based sequencing, while the 10-MLP package supports space-constrained PCB layouts. Programming requires a compatible connector and ISP-compatible programmer or bootloader arrangement.

Designers should pay close attention to power sequencing, decoupling, exposed-pad layout, and programming access in the 10-MLP footprint. Keep the ADC reference and sensitive signal routing away from fast-switching nodes, and confirm the selected package land pattern before release. This page combines manufacturer specifications, sourcing information, package guidance, practical application notes, and a focused replacement analysis for engineers evaluating the ATTINY13A-MMF.

के लिए ड्रॉप-इन विकल्प ATTINY13A-MMF — समान पैकेज, पिन-टू-पिन संगत। PCB रीवर्क आवश्यक करने वाले भिन्न-पैकेज पार्ट्स शामिल नहीं हैं।

इस उत्पाद के लिए कोई drop-in alternatives उपलब्ध नहीं।

विकल्प अनुरोध करें

ATTINY13A-MMF Maximum Ratings और Electrical Characteristics

Product Type 8-bit AVR microcontroller
अधिकतम क्लॉक फ़्रीक्वेंसी 20 MHz
Maximum Throughput 20 MIPS at 20 MHz
Flash Memory 1 KB
Flash Memory Organization 512 x 16 bits
EEPROM 64 bytes
SRAM 64 bytes
Register File 32 bytes
ADC Resolution 10 bits
ADC Channels 4 channels
Operating Voltage 1.8 V to 5.5 V
Architecture AVR enhanced RISC
Architecture Family tinyAVR
Low-Power Technology picoPower
पैकेज 10-MLP (3 x 3 mm)
माउंटिंग प्रकार Surface mount
Programming Interface In-Circuit Serial Programming (ICSP)
Debug Interface MPLAB Snap

ATTINY13A-MMF 10-mlp (3 x 3 mm) पिन कॉन्फ़िगरेशन गाइड

ATTINY13A-MMF (10-mlp (3 x 3 mm) पैकेज) के लिए पिन कॉन्फ़िगरेशन। इस डिजिटल IC में GPIO, संचार इंटरफ़ेस (UART, SPI, I2C) और पावर पिन शामिल हैं। वैकल्पिक पिन फ़ंक्शन और कॉन्फ़िगरेशन विकल्पों के लिए निर्माता डेटाशीट देखें। एम्बेडेड सिस्टम डिज़ाइन और PCB लेआउट के लिए आवश्यक।

ATTINY13A-MMF के लिए 10-mlp (3 x 3 mm) पैकेज पिनआउट आरेख

इसके लिए कोई विस्तृत pinout data उपलब्ध नहीं: ATTINY13A-MMF.

देखें डेटाशीट पूर्ण पिन कॉन्फ़िगरेशन के लिए।

सामान्य अनुप्रयोग

ATTINY13A-MMF के लिए उपयुक्त है 6 अनुप्रयोगs: Compact Sensor Interface, LED Sequencing and Lighting Control, Timer and Duty-Cycle Controller, Battery-Powered Embedded Control, USB-to-Serial Programmer Board, Small Consumer Appliance Controller.

🧩

Compact Sensor Interface

The ATTINY13A-MMF fits small analog-monitoring modules because it combines four 10-bit ADC channels with a 20 MHz AVR core in a 3 x 3 mm MLP package. The controller can sample sensors, apply threshold logic, and update an indicator or actuator without requiring a larger processor. Keep the application within the 1 KB flash and 64-byte SRAM limits, reference ADC decisions to the manufacturer’s pin and electrical tables, and isolate analog routing from switching nodes. Its picoPower architecture also supports low-power operation when the duty cycle permits sleep modes.

💡

LED Sequencing and Lighting Control

ATTINY13A-MMF is well suited to compact LED sequencers, status indicators, and low-current lighting controllers where board area is constrained. A 20 MHz clock supports precise timer-based updates, while the 1 KB program memory is sufficient for compact state machines and pulse patterns. Drive LEDs through suitable transistor or driver circuitry rather than overloading GPIO current limits, and account for PWM resolution when planning dimming behavior. The 10-MLP footprint also requires careful exposed-pad and paste-pattern review before production.

⚡

Timer and Duty-Cycle Controller

The ATTINY13A-MMF can implement compact timers, pulse generators, duty-cycle controls, and scheduled output systems using its 20 MHz AVR processing capability. Because AVR instructions execute in a single clock cycle, the device can deliver throughput approaching 1 MIPS per MHz, which simplifies precise event handling and short interrupt routines. Favor timer hardware for repetitive timing and reserve CPU cycles for control logic. Validate startup, rollover, and interrupt behavior across the 1.8 V to 5.5 V operating range before finalizing a production design.

🔋

Battery-Powered Embedded Control

ATTINY13A-MMF is appropriate for small battery-powered controls because the TinyAVR device combines picoPower operation with a low 1.8 V minimum supply voltage. A compact application can measure an analog condition, operate an output, and spend most of its time in a low-power state. Calculate the average current from active and sleep-mode behavior in the manufacturer datasheet, and size the external regulator or battery for peak loads. Firmware should minimize continuous ADC use and disable unused peripherals to preserve the intended power advantage.

🖥️

USB-to-Serial Programmer Board

ATTINY13A-MMF can serve as the target microcontroller in a compact USB-to-serial programmer board because it supports In-Circuit Serial Programming and is recognized by the MicroCore Arduino hardware package. The device also supports MPLAB Snap programming and debugging, providing familiar development paths. The 1 KB program-memory limit favors direct ISP operation or a very small bootloader in tightly constrained boards. Preserve the ISP signal access, add reliable reset and programming connectors, and verify that the USB-to-UART interface operates at the selected target voltage.

🏭

Small Consumer Appliance Controller

ATTINY13A-MMF can manage a simple appliance or accessory controller with a small state machine, button inputs, and one or more timed outputs. Its 64 bytes of SRAM and 1 KB flash are adequate for focused logic but not for extensive menu systems or complex protocols. Use the ADC only when the control function genuinely requires analog measurement, and select external drive components for loads beyond GPIO capability. For designs expected to grow in functions, firmware size, or I/O count, select a larger TinyAVR early to avoid a package and board redesign.

What are the key specifications of ATTINY13A-MMF that engineers should know?
The ATTINY13A-MMF is a 20 MHz, 8-bit AVR microcontroller with 1 KB of flash, 64 bytes of EEPROM, 64 bytes of SRAM, and a four-channel 10-bit ADC. According to the Microchip Technology ATtiny13A datasheet, it operates from 1.8 V to 5.5 V and delivers up to 20 MIPS throughput at 20 MHz. Its compact 10-MLP 3 x 3 mm package suits small control boards, while ICSP and MPLAB Snap support provide practical programming and debugging options.
Where can I download the ATTINY13A-MMF datasheet PDF?
The official ATTINY13A datasheet PDF is available from Microchip Technology through the manufacturer document link on this page. The document identifies the device as a low-power CMOS 8-bit MCU based on the AVR enhanced RISC architecture. It covers the 1 KB ISP Flash, 64-byte EEPROM, 64-byte SRAM, 32-byte register file, four-channel 10-bit ADC, electrical characteristics, and operating details needed for firmware and hardware design.
Where can I find the ATTINY13A-MMF pinout?
Use the pin-description table and package drawing in the Microchip Technology ATtiny13A datasheet to assign tracks for the 10-MLP package. The verified manufacturer material identifies the ATTINY13A-MMF as a 10-pin 3 x 3 mm MLP device, but it does not provide a package-specific pin diagram suitable for the product-page visualization. The datasheet remains the authoritative source for pin numbering, exposed-pad requirements, and alternate-function assignments before PCB routing.
What is the ATTINY13A-MMF operating voltage range?
The ATTINY13A-MMF operates from 1.8 V to 5.5 V, according to the Microchip Technology ATtiny13A product page. This range supports low-voltage designs as well as conventional 3.3 V and 5 V systems. Firmware configuration, brown-out behavior, ADC scaling, and clock settings must be checked against the selected supply voltage in the manufacturer datasheet, particularly when transitioning between low-power and maximum-clock operating modes.
How do I program an ATTINY13A-MMF?
Program the ATTINY13A-MMF through its In-Circuit Serial Programming interface using an ISP-compatible programmer or an established AVR development environment. Microchip supports the MPLAB Snap interface for programming and debugging, and the device can also be used in projects built around the MicroCore Arduino hardware package. Preserve access to the ISP signals in the PCB layout and confirm the programmer’s 1.8 V to 5.5 V logic compatibility before programming.
Can ATTINY13A-MMF be programmed with Arduino?
Yes, ATTINY13A-MMF boards can be programmed through Arduino-compatible AVR workflows using the MicroCore hardware package, which supports ATtiny13 and ATtiny13A devices. The software environment must select the correct ATtiny13A variant and clock configuration. Because the controller provides only 1 KB of flash, use a compact bootloader or direct ISP workflow and verify that the chosen board configuration maps its I/O pins consistently.
What can replace the ATTINY13A-MMF?
The closest documented functional migration is from the original ATTINY13 to the ATTINY13A, because the Microchip AVR520 application note describes the ATtiny13A as functionally identical and a drop-in replacement for ATtiny13. A replacement for the specific ATTINY13A-MMF 10-MLP footprint should also be checked for pin compatibility, memory organization, voltage range, and exposed-pad requirements. Packaging variants such as SOIC devices cannot be soldered directly onto the MLP land pattern.
Is ATTINY13A-MMF the same as ATTINY13A-SH?
No. ATTINY13A-MMF and ATTINY13A-SH belong to the same ATtiny13A device family, but ATTINY13A-MMF uses a 10-MLP 3 x 3 mm package while ATTINY13A-SH is associated with an 8-pin SOIC package. They therefore require different PCB land patterns and cannot be treated as direct package-compatible drop-ins. Confirm the exact ordering suffix, pin arrangement, and exposed-pad requirements before changing the bill of materials.
ATTINY13A-MMF vs ATTINY85-20SF: which is better for a small control project?
Choose the ATTINY13A-MMF for the smallest and simplest implementation when 1 KB of flash, 64 bytes of SRAM, and four ADC channels are sufficient. The ATTINY85-20SF belongs to a higher-resource TinyAVR family and offers more memory and I/O, but it also uses a larger SOIC footprint and is not a pin-compatible substitute for the 10-MLP target. Select the larger device only when code capacity, additional peripherals, or I/O requirements justify the added board area.
When should I choose ATTINY13A-MMF over a larger AVR microcontroller?
Choose ATTINY13A-MMF when the application is a compact controller whose firmware comfortably fits within 1 KB of flash and whose working data fits within 64 bytes of SRAM. Its 20 MHz clock, 10-bit ADC, and small 3 x 3 mm MLP package are useful for timers, simple sensor interfaces, and embedded control functions. Move to a larger TinyAVR when firmware growth, more I/O, additional communication peripherals, or more SRAM becomes important.
Is ATTINY13A-MMF suitable for compact sensor and LED-control projects?
Yes, ATTINY13A-MMF is suitable for compact sensor and LED-control projects that fit within its 1 KB flash and 64-byte SRAM limits. Its four-channel 10-bit ADC supports basic analog sensing, while the 20 MHz clock provides responsive timing and control. Keep the firmware concise, account for ADC conversion and filtering time, and design the MLP footprint correctly. The device is better suited to focused automation than complex user interfaces or multi-protocol gateways.
Where can I buy ATTINY13A-MMF online?
Use the Request a Quote form on this page to request the current price, stock position, and lead time for ATTINY13A-MMF. The Microchip Technology product page identifies the device as active, and the manufacturer listing shows it as available for configured orders. For production planning, confirm the exact 10-MLP suffix, tray packaging, and your required quantity through the quote process rather than relying on a historical catalog amount.
What is the lead time for ATTINY13A-MMF?
Current lead time and quantity availability should be requested through the Request a Quote form on this page. The Microchip Technology listing displayed 3,430 units in stock on January 23, 2026 and estimated an additional factory lead time of approximately eight weeks for more units. Since manufacturing schedules and allocation can change, use the quotation workflow for the present schedule and account for the 10-MLP packaging requirement in the order.
Is ATTINY13A-MMF in stock?
ATTINY13A-MMF is identified as an active Microchip Technology device, and the manufacturer listing reported 3,430 units in stock on January 23, 2026. For current inventory, use the Request a Quote form on this page and specify your required quantity. Also confirm whether you need the exact ATTINY13A-MMF suffix and tray configuration, because a related package suffix cannot be substituted without an assembly change.
What is the price of ATTINY13A-MMF?
Use the Request a Quote form on this page for the current ATTINY13A-MMF price and volume breaks. Structured pricing can vary with order quantity, packaging, market conditions, and delivery requirements, so a fixed price in product text can become stale. Include your annual usage, target quantity, and required packaging in the request to obtain a quotation suitable for BOM and production planning.

के लिए इंजीनियरिंग संदर्भ डेटा ATTINY13A-MMF — तुलना, डिज़ाइन मार्गदर्शन और अनुपालन जानकारी।

चयन गाइड

Choose ATTINY13A-MMF when the design needs a very small, low-cost 8-bit controller with up to 20 MHz operation, four 10-bit ADC channels, and only modest program and data memory. It is a strong fit for compact timers, LED control, simple sensor interfaces, and focused appliance functions. ATTINY13A-SH may be easier to prototype on a breadboard, but its SOIC package is physically larger. ATTINY13A-SSUR offers a different surface-mount format and is not interchangeable with the MLP land pattern. Choose ATTINY20-MMHR when firmware, SRAM, or peripheral requirements exceed the ATtiny13A’s 1 KB flash and 64-byte SRAM limits. For a production ATTINY13A-MMF board, verify the exact MLP footprint, exposed-pad treatment, programming access, and supply compatibility with the assembly and programming process.

विकल्पों के साथ तुलना

पैरामीटर यह उत्पाद
Package 10-MLP (3 x 3 mm)
Brand Microchip Technology
Core Processor 8-bit AVR
Maximum Clock Frequency 20 MHz
Flash Memory 1 KB
EEPROM 64 bytes
SRAM 64 bytes
ADC 4-channel, 10-bit
Operating Voltage 1.8 V to 5.5 V
Programming Interface In-Circuit Serial Programming

मुख्य विशेषताएँ

  • High processing throughput in a compact 3 x 3 mm footprint (बनामATTINY13A-SH)
  • Integrated analog conversion without an external ADC (बनामATTINY13A-SSUR)
  • Useful resource level for focused embedded control (बनामATTINY20-MMHR)

डिज़ाइन नोट्स

Design the 10-MLP land pattern directly from the manufacturer package drawing and confirm whether the exposed pad is electrically connected, solderable, or both. The canonical package-visualization library does not include an MLP-10 entry, so use the datasheet drawing as the controlling PCB footprint source. Place the decoupling capacitor close to the supply and ground pins, keep the exposed-pad geometry unobstructed, and confirm the assembly stencil and solder profile with the selected board manufacturer.

Keep the four ADC inputs on quiet, short traces and route them away from switching nodes, crystal or clock circuitry, and high-current outputs. If the ADC reference uses an external source, give that net a compact low-impedance layout and follow the manufacturer’s input-impedance recommendations. The ATTINY13A-MMF can execute up to 20 MIPS, so fast digital edges can couple into analog measurements even though the device itself has a 20 MHz maximum operating frequency.

Plan the power tree around the 1.8 V to 5.5 V operating range and ensure that the programmer logic, pull-ups, and connected peripherals use compatible voltage levels. Place local supply and ground capacitors at the device pins using the values and placement guidance in the manufacturer datasheet. Estimate average power from active-current, sleep-current, and duty-cycle values rather than using the maximum-clock current alone, particularly for battery-powered designs.

Do not treat related ATTINY13A package suffixes as interchangeable. ATTINY13A-SH and ATTINY13A-SSUR use different package formats from the ATTINY13A-MMF MLP device, so substituting them requires a new footprint and assembly process. Also monitor the 1 KB flash limit during toolchain selection, remove unused library code, and verify the configured clock and fuse settings against the operating voltage before programming production units.

अनुपालन जानकारी

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
लीड फ्री
Unknown
हैलोजन फ्री
Unknown
कॉन्फ्लिक्ट मिनरल्स
Unknown

No explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations were present in the manufacturer or distributor material.

डेटा सत्यापन तिथि: 2026-11-19 — डेटा XAIPART की कंपोनेंट इंजीनियरिंग टीम द्वारा सत्यापित और क्यूरेट किया गया

संबंधित खोजें

attiny13a pinout attiny13a datasheet attiny13a price attiny13a programming attiny13a vs attiny85 attiny13a programming with arduino attiny13 projects attiny13a smd attiny13a datasheet pdf ATTINY13A-MMF datasheet pdf ATTINY13A-MMF pinout ATTINY13A-MMF equivalent ATTINY13A-MMF replacement ATTINY13A-MMF 20MHz Microchip ATTINY13A-MMF

संबंधित कंपोनेंट्स और शब्द

Microchip Technology ATTINY13A-MMF ATTINY13A ATTINY13A-SH ATTINY13A-SSUR ATTINY20-MMHR 8-bit microcontroller AVR enhanced RISC architecture tinyAVR picoPower embedded microcontroller semiconductor 10-MLP 3 x 3 mm surface-mount package In-Circuit Serial Programming MPLAB Snap 10-bit ADC 1 KB flash memory 64-byte EEPROM 64-byte SRAM 20 MHz clock Arduino MicroCore RoHS REACH
त्वरित क़ौतिल आदेश (RFQ)
पूर्ण विवरण भरें — हमारी सेल्स टीम 24 घंटे के भीतर जवाब देगी
पार्ट नंबर निर्माता पैकेज QTY लक्ष्य कीमत विस्तारित
✓
उद्धरण प्रस्तुत!

हम आपकी ईमेल पर 24 घंटे के भीतर जवाब देंगे

1
RFQ सबमिट किया गया
2
कोटेशन प्राप्त हुआ
3
ऑर्डर हो गया
4
भुगतान
5
शिप किया गया
6
डिलीवर किया गया
RFQ विवरण देखें