Microchip Technology

ATTINY45-15SZ - 4KB AVR MCU, 15MHz | Microchip Technology

MPN: ATTINY45-15SZ ✓ সক্রিয়
8-SOIC, 5.30 mm width Package 15 MHz Speed 4 KB (2K x 16) Memory
সর্বনিম্ন অর্ডার পরিমাণ: 1 |

ATTINY45-15SZ সারাংশ

The Microchip Technology ATTINY45-15SZ is a low-power 8-bit AVR RISC microcontroller with 4 KB of ISP Flash memory, 256 bytes of EEPROM, 256 bytes of SRAM, six general-purpose I/O lines, and a maximum clock speed of 15 MHz. The device is supplied in an 8-pin SOIC package, making it suitable for compact embedded-control designs that require modest program memory and a small footprint.

An 8-bit AVR microcontroller is a compact semiconductor controller built around a RISC-based processing core, general-purpose registers, embedded memory, and programmable I/O. The ATTINY45 belongs to the TinyAVR product family, a low-power branch of the AVR embedded portfolio. Its combination of serial programming, EEPROM, SRAM, timers, and communication peripherals supports compact control, sensing, and signal-processing systems.

Key device features include 4 KB of program Flash, 256 bytes of data EEPROM, 256 bytes of SRAM, and six general-purpose I/O lines. The manufacturer identifies a 32-register working-register architecture, one 8-bit timer/counter with compare modes, and an internal oscillator. These resources allow the ATTINY45-15SZ to execute small control routines while occupying only an 8-pin package.

The -15 designation identifies the 15 MHz speed grade, while the Z package code corresponds to the 8-pin SOIC form used by this ordering variant. The same ATtiny25/45/85 family has been qualified to AEC-Q100 grade 1 according to the manufacturer datasheet. Peripheral timing, brownout behavior, clock behavior, and electrical limits should therefore be checked against the specific ordering code before a production release.

Typical uses include compact sensor nodes, simple motor or actuator controllers, LED lighting sequencers, battery-powered instruments, small fan controllers, and communication modules. The six I/O lines are sufficient for basic digital interfaces, while the internal oscillator eliminates the need for an external clock in many designs. More demanding interfaces should be checked against the available pin count and the ATtiny45-15SZ application matrix.

PCB design should preserve the SOIC-8 footprint, provide the required decoupling at the supply pins, and route reset and programming signals so switching noise does not interfere with startup or ISP programming. Firmware development is commonly performed with AVR-compatible toolchains and the ISP interface; programming details should follow the manufacturer ATtiny25/45/85 documentation.

This page organizes the ATTINY45-15SZ specifications, package information, family comparisons, application guidance, and validated drop-in alternatives into an engineering-focused reference. It also identifies where package, memory, qualification, or sourcing review is still required before component substitution or production release.

এর জন্য ড্রপ-ইন বিকল্প ATTINY45-15SZ — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।

ATTINY45-15ST1

✅ ড্রপ-ইন
📦 8-SOIC
Same ATtiny45 core, 4 KB Flash, 256-byte EEPROM, 256-byte SRAM, and 15 MHz speed; the ordering suffix identifies a different grade classification, with 4 KB Flash and 15 MHz unchanged

📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)

ATTINY45-15ST

✅ ড্রপ-ইন
📦 8-SOIC
Same ATtiny45 core, 4 KB Flash, 256-byte EEPROM, 256-byte SRAM, and 15 MHz speed; ordering-code and grade details differ while core resource values remain unchanged

📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)

ATTINY45-15SU

✅ ড্রপ-ইন
📦 8-SOIC
Same ATtiny45 core, 4 KB Flash, 256-byte EEPROM, 256-byte SRAM, and 15 MHz speed; package ordering code differs while the electrical core resources remain unchanged

📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)

ATTINY45-15SZ সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য

Device Type 8-bit AVR RISC microcontroller
Maximum Clock Speed 15 MHz
Program Flash Memory 4 KB (2K x 16)
EEPROM Memory 256 bytes
SRAM 256 bytes (256 x 8)
General-Purpose I/O Pins 6
Working Registers 32
Timer/Counter One 8-bit timer/counter with compare modes
Oscillator Type Internal
Programming Interface In-System Programming (ISP)
Architecture AVR enhanced RISC
প্যাকেজ 8-SOIC, 5.30 mm width
মাউন্টিং টাইপ Surface mount
Packaging Tape and reel
Automotive Qualification AEC-Q100 grade 1

ATTINY45-15SZ 8-soic, 5.30 mm width পিন কনফিগারেশন গাইড

ATTINY45-15SZ (8-soic, 5.30 mm width প্যাকেজ)-এর পিন কনফিগারেশন। এই ডিজিটাল IC-তে GPIO, কমিউনিকেশন ইন্টারফেস (UART, SPI, I2C) এবং পাওয়ার পিন রয়েছে। বিকল্প পিন ফাংশন ও কনফিগারেশন অপশনের জন্য প্রস্তুতকারকের ডেটাশিট দেখুন। এমবেডেড সিস্টেম ডিজাইন ও PCB লেআউটের জন্য অপরিহার্য।

ATTINY45-15SZ-এর জন্য 8-soic, 5.30 mm width প্যাকেজ পিনআউট ডায়াগ্রাম

এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি ATTINY45-15SZ.

দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।

সাধারণ ব্যবহার

ATTINY45-15SZ এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Compact Sensor Node, LED Lighting Sequencer, Small Motor Controller, Battery-Powered Instrument, Simple Communication Module, Automotive Auxiliary Controller.

🧩

Compact Sensor Node

The ATTINY45-15SZ fits compact sensor nodes that require periodic measurement, local control, and low standby activity without a large processor package. Its 4 KB of ISP Flash can hold acquisition routines and calibration logic, while 256 bytes of EEPROM can retain small configuration values and 256 bytes of SRAM can support short processing tasks. The six general-purpose I/O lines provide connections for a digital sensor, status indication, and a simple serial interface. Using the internal oscillator can reduce external component count, although the final clock and sleep configuration must follow the manufacturer guidance. For designs requiring higher data throughput or more simultaneous peripherals, move to a larger ATtiny family member rather than treating the six I/O limit as flexible.

💡

LED Lighting Sequencer

The ATTINY45-15SZ can implement LED sequencing, status indication, and simple dimming patterns in compact lighting modules. Six general-purpose I/O lines are enough for multiple direct digital channels when the selected LED currents and drive requirements are appropriate, while the 8-bit timer/counter with compare modes supports timing-based effects. The 4 KB Flash capacity is sufficient for a dedicated sequence engine and does not justify a larger microcontroller when the lighting pattern is fixed. Use transistor or constant-current driver circuitry whenever the indicator or LED string cannot be driven directly from an I/O pin, and account for simultaneous-output current limits in the manufacturer electrical tables.

🏭

Small Motor Controller

The ATTINY45-15SZ is appropriate for small motor, solenoid, or actuator-control boards where the control algorithm is modest and board space is important. The 15 MHz AVR core and timer compare functions can support deterministic pulse-width, direction, or motion-limit logic, while the six I/O pins can serve control inputs and driver commands. The device does not directly replace a motor driver or provide the required output current, so external transistor and protection stages remain necessary. Flicker, stall current, inductive voltage excursions, and thermal rise should be evaluated before deployment. The ATTINY85 family is preferable when the controller also runs communications, logging, or more complex motion routines.

🔧

Battery-Powered Instrument

The ATTINY45-15SZ can serve as the control element in a battery-powered instrument when the device must combine low-power operation with local configuration and simple user-interface functions. Its internal oscillator, 256 bytes of EEPROM, 256 bytes of SRAM, and 4 KB Flash provide enough resources for calibration tables, button handling, status feedback, and periodic measurements. Low-power performance depends on selecting the appropriate clock and sleep modes rather than treating the clock rating as a direct battery-life specification. For instruments that must retain more application code or support more concurrent interfaces, compare the ATTINY85 family. Firmware should avoid continuous busy waiting because the idle-state behavior determines whether the battery budget is met.

🌐

Simple Communication Module

The ATTINY45-15SZ can implement a compact protocol endpoint or configuration bridge when the interface is limited to a few serial signals and packet processing is straightforward. Six I/O lines can support a UART-style or software-defined serial connection, a status output, and a control input, while 4 KB of Flash can hold the protocol state machine and device-specific commands. The part has no dedicated USB interface, so USB applications require another controller or a carefully selected USB-capable MCU. Protocol timing, idle-state consumption, receive buffering, and external transceiver requirements should be reviewed before deployment. If packet buffers or firmware growth are likely, the ATTINY85 provides a straightforward capacity upgrade within the same broad product family.

🚗

Automotive Auxiliary Controller

The ATTINY45-15SZ is suitable for selected automotive auxiliary-control applications because the manufacturer family documentation states that the ATtiny25/45/85 family has been qualified to AEC-Q100 grade 1. The 4 KB Flash, 256-byte EEPROM, 256-byte SRAM, and six I/O lines support small control functions such as interface translation, status logic, or distributed actuator management. Qualification does not automatically qualify every end product, so the final assembly still requires environmental, EMC, functional-safety, and application-specific validation. Confirm the exact ATTINY45 suffix temperature range and automotive qualification before procurement. The smaller ATTINY25 is useful only when its 2 KB Flash budget remains sufficient for the selected function.

সুপারিশকৃত পণ্যের সারসংক্ষেপ

ATTINY45-15SZ Microchip Technology ব্যবহৃত হয়: Compact Sensor Node, LED Lighting Sequencer, Small Motor Controller, Battery-Powered Instrument, Simple Communication Module, Automotive Auxiliary Controller ATTINY85-15SZ Higher-memory family alternative when firmware or I/O demand increases ব্যবহৃত হয়: Compact Sensor Node, Small Motor Controller, Simple Communication Module ATTINY25-15SZ Lower-memory family member for simpler fixed patterns ব্যবহৃত হয়: LED Lighting Sequencer ATTINY45 Family-level configuration reference ব্যবহৃত হয়: Battery-Powered Instrument ATTINY25-15ST1 Lower-memory automotive-family option for simpler functions ব্যবহৃত হয়: Automotive Auxiliary Controller
What are the key specifications of ATTINY45-15SZ that engineers should know?
The ATTINY45-15SZ is an 8-bit AVR microcontroller with 4 KB of ISP Flash memory, 256 bytes of EEPROM, 256 bytes of SRAM, six general-purpose I/O lines, and a 15 MHz maximum clock speed. According to the Microchip Technology ATtiny45 product page, the device also provides 32 working registers and one 8-bit timer/counter with compare modes. It is packaged in an 8-SOIC format and is based on the low-power TinyAVR product family.
Where can I download the ATTINY45-15SZ datasheet PDF?
The ATTINY45-15SZ datasheet PDF is available through the manufacturer family documentation and the indexed Microchip document at datasheets.com. According to the manufacturer datasheet, the document covers the ATtiny25/45/85 family and includes electrical limits, characterization results, package information, and operating conditions. Use the family pin-description and ordering tables to confirm that the Z suffix corresponds to the exact 8-SOIC assembly being assembled.
What is the ATTINY45-15SZ pinout?
The ATTINY45-15SZ uses an eight-pin SOIC arrangement with six general-purpose I/O lines, a ground connection, a supply connection, and a reset connection. The manufacturer ATtiny45 documentation provides the authoritative pin-description table for assigning PCB nets. Because the exact numbered pin names are not published in the product summary on this page, consult the datasheet pin-description table before routing power, reset, programming, or I/O signals.
What is the difference between ATTINY45 and ATTINY85?
The ATTINY45 and ATTINY85 belong to the same AVR family and use a comparable 8-SOIC footprint, but their memory and I/O resources differ. The ATTINY45 provides 4 KB of Flash, 256 bytes of EEPROM, 256 bytes of SRAM, and six general-purpose I/O lines. The manufacturer family comparison identifies the ATTINY85 with more Flash and I/O resources, so software memory assumptions and PCB connections must be reviewed before using one as a replacement.
Can ATTINY45-15SZ be used for Arduino-style projects?
The ATTINY45-15SZ can support compact Arduino-style embedded projects when the firmware, bootloader, and board definitions match the ATtiny45 device and package. Its 4 KB of Flash limits program size, while six I/O lines constrain simultaneous peripherals. According to the Microchip Technology ATtiny45 product page, the core includes 32 working registers, EEPROM, SRAM, and an 8-bit timer/counter, making it suitable for small control tasks rather than large Arduino sketches.
How do I program an ATTINY45-15SZ?
The ATTINY45-15SZ is programmed through its In-System Programming interface using an AVR-compatible programmer and the appropriate device settings. The ISP interface allows firmware to be written without removing the microcontroller from the circuit. Follow the Microchip ATtiny25/45/85 programming guidance for clock selection, fuse configuration, reset timing, and tool settings, and confirm the target package before assigning the ISP connector.
Is ATTINY45-15SZ suitable for battery-powered devices?
The ATTINY45-15SZ is suitable for many battery-powered devices because it belongs to Microchip Technology's low-power AVR family and supports an internal oscillator. The six available I/O lines and compact SOIC-8 package also help reduce board area in wearable, sensor, and remote-control products. Actual battery life depends on the selected operating mode, clock configuration, peripheral duty cycle, and sleep implementation, which must be evaluated with the family datasheet.
What is the best drop-in replacement for ATTINY45-15SZ?
The closest drop-in choices are ATTINY45-15ST1 and ATTINY45-15ST because they retain the ATtiny45 core, 4 KB Flash configuration, 15 MHz speed grade, and 8-SOIC footprint. According to the Microchip family datasheet, ATtiny25/45/85 devices are qualified to AEC-Q100 grade 1. Confirm the exact temperature range, package dimensions, pin functions, and active ordering status for the replacement before releasing a new production BOM.
Can ATTINY45-15ST1 replace ATTINY45-15SZ?
The ATTINY45-15ST1 can serve as a same-footprint ATTINY45 replacement candidate because the comparison identifies it as an 8-pin SOIC automotive ATtiny45-family device. Its key computational resources remain 4 KB of Flash, 256 bytes of EEPROM, 256 bytes of SRAM, and 15 MHz operation. Before substitution, compare the exact package drawing, temperature limits, qualification status, and ordering suffix in the manufacturer documentation.
When should I choose ATTINY45-15SZ instead of ATTINY85-15SZ?
Choose the ATTINY45-15SZ when a design needs only 4 KB of Flash, 256 bytes of SRAM, 256 bytes of EEPROM, and six general-purpose I/O lines. It is the appropriate choice when firmware size, I/O count, and board area are more important than the additional resources of the ATTINY85. The ATTINY85 is preferable for larger programs or more peripherals, but changing families requires a new pin assignment and firmware review.
Is ATTINY45-15SZ suitable for LED lighting and small motor control?
The ATTINY45-15SZ is suitable for compact LED sequencing and small actuator-control functions because it combines six general-purpose I/O lines with an 8-bit timer/counter that includes compare modes. The internal oscillator can support timing functions without an external crystal in suitable designs. Motor outputs still require suitable driver circuitry, current protection, and grounding, while LED designs should include the required current-limiting method.
Where can I buy ATTINY45-15SZ online?
Use the Request a Quote form on this page to request ATTINY45-15SZ availability, current unit pricing, and lead time. The form is the appropriate route for a quotation because market pricing and inventory can change quickly. For comparison before requesting an order, review the 8-SOIC package, 15 MHz speed grade, and automotive qualification information against the product requirements.
What is the price of ATTINY45-15SZ?
Current ATTINY45-15SZ pricing is not stated in static page content because prices and inventory change frequently. Use the Request a Quote form on this page for the current unit price, quantity breaks, stock position, and lead time. Include the desired package, order quantity, and target date so the quotation can be matched to the exact 8-SOIC ordering variant.
What is the lead time and stock status of ATTINY45-15SZ?
The ATTINY45-15SZ is identified as an active Microchip Technology product, but a fixed stock quantity and lead time should not be assumed. Request current availability, minimum order quantity, and lead time through the Request a Quote form on this page. Include your production schedule and annual usage because supply timing can vary with order size and packaging requirements.
What is the best Microchip Technology equivalent for ATTINY45-15SZ?
The best same-family candidates are ATTINY45-15ST1 and ATTINY45-15ST because they preserve the ATtiny45 architecture, 4 KB Flash memory, 256-byte EEPROM, 256-byte SRAM, 15 MHz operating speed, and 8-SOIC package format. According to the Microchip Technology family documentation, the ATtiny25/45/85 family is qualified to AEC-Q100 grade 1. Verify the exact suffix-specific temperature range and package dimensions before substitution.
Does the ATTINY45-15SZ support USB communication?
The ATTINY45-15SZ does not provide a dedicated USB interface in the manufacturer ATtiny45 product summary. Software-controlled serial communication can still be implemented on available I/O pins, while a separate USB controller may be required when USB enumeration or a standardized USB connector is necessary. For designs mentioning ATTINY45 USB, select an appropriate USB-capable microcontroller or add a documented external interface rather than assuming native USB support.

এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা ATTINY45-15SZ — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।

নির্বাচন গাইড

Choose the ATTINY45-15SZ for compact designs needing 4 KB of Flash, 256 bytes of SRAM, 256 bytes of EEPROM, six general-purpose I/O lines, and operation up to 15 MHz. Select ATTINY45-15ST1 when the exact ordering and qualification requirements of that suffix better match the product program; select ATTINY45-15ST or ATTINY45-15SU when their suffix-specific temperature or package conditions fit the assembly. All three candidates belong to the same ATtiny45 family and preserve the core resource configuration, but each still requires verification of the package drawing and suffix-specific limits. Consider ATTINY85-15SZ instead when firmware size, SRAM, EEPROM, or I/O requirements exceed the ATtiny45's capacity. Consider ATTINY25-15SZ only for substantially smaller programs, recognizing that its 2 KB Flash is half the target's 4 KB.

বিকল্পের সাথে তুলনা

পারামিটার এই পণ্য ATTINY45-15ST1 ATTINY45-15ST ATTINY45-15SU
Brand Microchip Technology Microchip Technology Microchip Technology Microchip Technology
Package 8-SOIC 8-SOIC - same package format 8-SOIC - same package format 8-SOIC - same package format
Architecture 8-bit AVR RISC 8-bit AVR RISC 8-bit AVR RISC 8-bit AVR RISC
Maximum Clock Speed 15 MHz 15 MHz 15 MHz 15 MHz
Program Flash Memory 4 KB (2K x 16) 4 KB (2K x 16) 4 KB (2K x 16) 4 KB (2K x 16)
EEPROM Memory 256 bytes 256 bytes 256 bytes 256 bytes
SRAM 256 bytes (256 x 8) 256 bytes (256 x 8) 256 bytes (256 x 8) 256 bytes (256 x 8)
General-Purpose I/O Pins 6 6 6 6
Oscillator Type Internal Internal Internal Internal
Automotive Qualification AEC-Q100 grade 1 family qualification AEC-Q100 grade 1 family qualification AEC-Q100 grade 1 family qualification AEC-Q100 grade 1 family qualification

মূল পার্থক্যসমূহ

  • Maintains the ATtiny45 resource configuration across the drop-in candidates (বনামATTINY45-15ST1)
  • Compact eight-pin implementation for embedded control (বনামATTINY45-15ST)
  • Uses an internal oscillator for a reduced external component count (বনামATTINY45-15SU)

ডিজাইন নোট

Assign power, ground, reset, and programming signals from the manufacturer pin-description table rather than inferring connections from a generic 8-pin SOIC drawing. Place the required supply bypass capacitor close to the device's supply pin, provide a low-impedance ground return, and keep the ISP connector and reset trace away from noisy switching nodes. Because the ATTINY45 has only six general-purpose I/O lines, verify all peripheral connections before committing the PCB footprint.

Treat the 15 MHz figure as a maximum clock speed, not a guaranteed operating point for every supply voltage. Select the operating frequency using the manufacturer electrical-limit tables for the relevant voltage and temperature conditions, and configure the clock and power modes through the appropriate fuses and firmware. In battery-powered products, measure sleep current, active current, and wake-up time in the final board because external regulator, pull resistors, and connected peripherals can dominate the budget.

Do not substitute a lower-memory ATtiny25 or higher-resource ATtiny85 into an ATTINY45 design without reviewing the firmware image and PCB pin assignments. The target offers 4 KB of Flash, 256 bytes of EEPROM, 256 bytes of SRAM, and six general-purpose I/O lines; changing the family member can alter memory limits, available ports, and boot or programming assumptions. A same-footprint component is only a drop-in candidate after its ordering suffix, temperature grade, and package drawing have been checked.

Keep the 8-SOIC footprint within the manufacturer's land-pattern and solder recommendations, including lead pitch, body width, and exposed termination geometry. Inspect the final assembly for solder bridges across the closely spaced SOIC leads, especially around reset and programming nets. If the board operates near motors, relays, LEDs, or switching regulators, route the clock and sensitive control paths away from high-current edges and provide local return paths to reduce noise-induced resets or programming faults.

কমপ্লায়েন্স তথ্য

RoHS
Unknown
REACH
Unknown
AEC-Q100
Qualified
লিড ফ্রি
Unknown
হ্যালোজেন ফ্রি
Unknown
কনফ্লিক্ট মিনারেলস
Unknown

The manufacturer datasheet states that the ATtiny25/45/85 family was verified during product qualification to AEC-Q100 grade 1. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status are unknown for the exact ordering variant.

ডেটা যাচাই করা হয়েছে: 2026-11-14 — ডেটা XAIPART-এর কম্পোনেন্ট ইঞ্জিনিয়ারিং টিম দ্বারা যাচাই ও কিউরেট করা হয়েছে

সম্পর্কিত অনুসন্ধান

attiny45 pinout attiny45 datasheet attiny45 vs attiny85 attiny45 arduino attiny45 price attiny45 programming attiny45 usb ATTINY45-15SZ datasheet ATTINY45-15SZ pinout ATTINY45-15SZ equivalent ATTINY45-15SZ replacement ATTINY45-15SZ price ATTINY45-15SZ vs ATTINY45-15ST1 Microchip Technology ATTINY45-15SZ

সম্পর্কিত কম্পোনেন্ট ও শর্তাবলী

Microchip Technology ATTINY45-15SZ ATTINY45 ATTINY25-15SZ ATTINY85-15SZ ATTINY45-15ST1 ATTINY45-15ST ATTINY45-15SU AVR TinyAVR 8-bit RISC microcontroller embedded microcontroller semiconductor In-System Programming ISP internal oscillator general-purpose I/O flash memory EEPROM SRAM 8-bit timer/counter SOIC-8 surface-mount package AEC-Q100 grade 1
তাৎক্ষণিক বিলওয়াছে রেকোজিউইট
সম্পূর্ণ বিবরণ পূরণ করুন — আমাদের সেলস টিম 24 ঘণ্টার মধ্যে উত্তর দেবে
পার্ট নম্বর উৎপাদক প্যাকেজ QTY লক্ষ্যমূল্য প্রসারিত
✓
বিল প্রস্তুত করা হয়েছে!

আমরা ২৪ ঘণ্টার মধ্যে আপনার ইমেইলে প্রত্যুত্তর দেব

1
RFQ জমা হয়েছে
2
কোটেশন পাওয়া গেছে
3
অর্ডার দেওয়া হয়েছে
4
পেমেন্ট
5
শিপ করা হয়েছে
6
ডেলিভারি হয়েছে
RFQ বিবরণ দেখুন