ATTINY45-15SZ - 4KB AVR MCU, 15MHz | Microchip Technology
N.º da peça: ATTINY45-15SZ ✓ AtivoATTINY45-15SZ Visão geral
An 8-bit AVR microcontroller is a compact semiconductor controller built around a RISC-based processing core, general-purpose registers, embedded memory, and programmable I/O. The ATTINY45 belongs to the TinyAVR product family, a low-power branch of the AVR embedded portfolio. Its combination of serial programming, EEPROM, SRAM, timers, and communication peripherals supports compact control, sensing, and signal-processing systems.
Key device features include 4 KB of program Flash, 256 bytes of data EEPROM, 256 bytes of SRAM, and six general-purpose I/O lines. The manufacturer identifies a 32-register working-register architecture, one 8-bit timer/counter with compare modes, and an internal oscillator. These resources allow the ATTINY45-15SZ to execute small control routines while occupying only an 8-pin package.
The -15 designation identifies the 15 MHz speed grade, while the Z package code corresponds to the 8-pin SOIC form used by this ordering variant. The same ATtiny25/45/85 family has been qualified to AEC-Q100 grade 1 according to the manufacturer datasheet. Peripheral timing, brownout behavior, clock behavior, and electrical limits should therefore be checked against the specific ordering code before a production release.
Typical uses include compact sensor nodes, simple motor or actuator controllers, LED lighting sequencers, battery-powered instruments, small fan controllers, and communication modules. The six I/O lines are sufficient for basic digital interfaces, while the internal oscillator eliminates the need for an external clock in many designs. More demanding interfaces should be checked against the available pin count and the ATtiny45-15SZ application matrix.
PCB design should preserve the SOIC-8 footprint, provide the required decoupling at the supply pins, and route reset and programming signals so switching noise does not interfere with startup or ISP programming. Firmware development is commonly performed with AVR-compatible toolchains and the ISP interface; programming details should follow the manufacturer ATtiny25/45/85 documentation.
This page organizes the ATTINY45-15SZ specifications, package information, family comparisons, application guidance, and validated drop-in alternatives into an engineering-focused reference. It also identifies where package, memory, qualification, or sourcing review is still required before component substitution or production release.
Alternativas drop-in para ATTINY45-15SZ — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
ATTINY45-15ST1
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
ATTINY45-15ST
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
ATTINY45-15SU
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
ATTINY45-15SZ Classificações máximas e características elétricas
| Device Type | 8-bit AVR RISC microcontroller |
| Maximum Clock Speed | 15 MHz |
| Program Flash Memory | 4 KB (2K x 16) |
| EEPROM Memory | 256 bytes |
| SRAM | 256 bytes (256 x 8) |
| General-Purpose I/O Pins | 6 |
| Working Registers | 32 |
| Timer/Counter | One 8-bit timer/counter with compare modes |
| Oscillator Type | Internal |
| Programming Interface | In-System Programming (ISP) |
| Architecture | AVR enhanced RISC |
| Encapsulamento | 8-SOIC, 5.30 mm width |
| Tipo de montagem | Surface mount |
| Packaging | Tape and reel |
| Automotive Qualification | AEC-Q100 grade 1 |
Guia de Configuração de Pinos do ATTINY45-15SZ 8-soic, 5.30 mm width
Configuração de pinos para ATTINY45-15SZ (pacote 8-soic, 5.30 mm width). Este CI digital inclui GPIO, interfaces de comunicação (UART, SPI, I2C) e pinos de alimentação. Consulte o datasheet do fabricante para funções alternativas dos pinos e opções de configuração. Essencial para projeto de sistemas embarcados e layout de PCB.
Nenhum dado detalhado de pinagem disponível para ATTINY45-15SZ.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
ATTINY45-15SZ é adequado para 6 aplicaçãos: Compact Sensor Node, LED Lighting Sequencer, Small Motor Controller, Battery-Powered Instrument, Simple Communication Module, Automotive Auxiliary Controller.
Compact Sensor Node
The ATTINY45-15SZ fits compact sensor nodes that require periodic measurement, local control, and low standby activity without a large processor package. Its 4 KB of ISP Flash can hold acquisition routines and calibration logic, while 256 bytes of EEPROM can retain small configuration values and 256 bytes of SRAM can support short processing tasks. The six general-purpose I/O lines provide connections for a digital sensor, status indication, and a simple serial interface. Using the internal oscillator can reduce external component count, although the final clock and sleep configuration must follow the manufacturer guidance. For designs requiring higher data throughput or more simultaneous peripherals, move to a larger ATtiny family member rather than treating the six I/O limit as flexible.
Recomendado
LED Lighting Sequencer
The ATTINY45-15SZ can implement LED sequencing, status indication, and simple dimming patterns in compact lighting modules. Six general-purpose I/O lines are enough for multiple direct digital channels when the selected LED currents and drive requirements are appropriate, while the 8-bit timer/counter with compare modes supports timing-based effects. The 4 KB Flash capacity is sufficient for a dedicated sequence engine and does not justify a larger microcontroller when the lighting pattern is fixed. Use transistor or constant-current driver circuitry whenever the indicator or LED string cannot be driven directly from an I/O pin, and account for simultaneous-output current limits in the manufacturer electrical tables.
Recomendado
Small Motor Controller
The ATTINY45-15SZ is appropriate for small motor, solenoid, or actuator-control boards where the control algorithm is modest and board space is important. The 15 MHz AVR core and timer compare functions can support deterministic pulse-width, direction, or motion-limit logic, while the six I/O pins can serve control inputs and driver commands. The device does not directly replace a motor driver or provide the required output current, so external transistor and protection stages remain necessary. Flicker, stall current, inductive voltage excursions, and thermal rise should be evaluated before deployment. The ATTINY85 family is preferable when the controller also runs communications, logging, or more complex motion routines.
Recomendado
Battery-Powered Instrument
The ATTINY45-15SZ can serve as the control element in a battery-powered instrument when the device must combine low-power operation with local configuration and simple user-interface functions. Its internal oscillator, 256 bytes of EEPROM, 256 bytes of SRAM, and 4 KB Flash provide enough resources for calibration tables, button handling, status feedback, and periodic measurements. Low-power performance depends on selecting the appropriate clock and sleep modes rather than treating the clock rating as a direct battery-life specification. For instruments that must retain more application code or support more concurrent interfaces, compare the ATTINY85 family. Firmware should avoid continuous busy waiting because the idle-state behavior determines whether the battery budget is met.
Recomendado
Simple Communication Module
The ATTINY45-15SZ can implement a compact protocol endpoint or configuration bridge when the interface is limited to a few serial signals and packet processing is straightforward. Six I/O lines can support a UART-style or software-defined serial connection, a status output, and a control input, while 4 KB of Flash can hold the protocol state machine and device-specific commands. The part has no dedicated USB interface, so USB applications require another controller or a carefully selected USB-capable MCU. Protocol timing, idle-state consumption, receive buffering, and external transceiver requirements should be reviewed before deployment. If packet buffers or firmware growth are likely, the ATTINY85 provides a straightforward capacity upgrade within the same broad product family.
Recomendado
Automotive Auxiliary Controller
The ATTINY45-15SZ is suitable for selected automotive auxiliary-control applications because the manufacturer family documentation states that the ATtiny25/45/85 family has been qualified to AEC-Q100 grade 1. The 4 KB Flash, 256-byte EEPROM, 256-byte SRAM, and six I/O lines support small control functions such as interface translation, status logic, or distributed actuator management. Qualification does not automatically qualify every end product, so the final assembly still requires environmental, EMC, functional-safety, and application-specific validation. Confirm the exact ATTINY45 suffix temperature range and automotive qualification before procurement. The smaller ATTINY25 is useful only when its 2 KB Flash budget remains sufficient for the selected function.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para ATTINY45-15SZ — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | ATTINY45-15ST1 | ATTINY45-15ST | ATTINY45-15SU |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 8-SOIC | 8-SOIC - same package format | 8-SOIC - same package format | 8-SOIC - same package format |
| Architecture | 8-bit AVR RISC | 8-bit AVR RISC | 8-bit AVR RISC | 8-bit AVR RISC |
| Maximum Clock Speed | 15 MHz | 15 MHz | 15 MHz | 15 MHz |
| Program Flash Memory | 4 KB (2K x 16) | 4 KB (2K x 16) | 4 KB (2K x 16) | 4 KB (2K x 16) |
| EEPROM Memory | 256 bytes | 256 bytes | 256 bytes | 256 bytes |
| SRAM | 256 bytes (256 x 8) | 256 bytes (256 x 8) | 256 bytes (256 x 8) | 256 bytes (256 x 8) |
| General-Purpose I/O Pins | 6 | 6 | 6 | 6 |
| Oscillator Type | Internal | Internal | Internal | Internal |
| Automotive Qualification | AEC-Q100 grade 1 family qualification | AEC-Q100 grade 1 family qualification | AEC-Q100 grade 1 family qualification | AEC-Q100 grade 1 family qualification |
Principais diferenciais
- Maintains the ATtiny45 resource configuration across the drop-in candidates (vs ATTINY45-15ST1)
- Compact eight-pin implementation for embedded control (vs ATTINY45-15ST)
- Uses an internal oscillator for a reduced external component count (vs ATTINY45-15SU)
Notas de projeto
Assign power, ground, reset, and programming signals from the manufacturer pin-description table rather than inferring connections from a generic 8-pin SOIC drawing. Place the required supply bypass capacitor close to the device's supply pin, provide a low-impedance ground return, and keep the ISP connector and reset trace away from noisy switching nodes. Because the ATTINY45 has only six general-purpose I/O lines, verify all peripheral connections before committing the PCB footprint.
Treat the 15 MHz figure as a maximum clock speed, not a guaranteed operating point for every supply voltage. Select the operating frequency using the manufacturer electrical-limit tables for the relevant voltage and temperature conditions, and configure the clock and power modes through the appropriate fuses and firmware. In battery-powered products, measure sleep current, active current, and wake-up time in the final board because external regulator, pull resistors, and connected peripherals can dominate the budget.
Do not substitute a lower-memory ATtiny25 or higher-resource ATtiny85 into an ATTINY45 design without reviewing the firmware image and PCB pin assignments. The target offers 4 KB of Flash, 256 bytes of EEPROM, 256 bytes of SRAM, and six general-purpose I/O lines; changing the family member can alter memory limits, available ports, and boot or programming assumptions. A same-footprint component is only a drop-in candidate after its ordering suffix, temperature grade, and package drawing have been checked.
Keep the 8-SOIC footprint within the manufacturer's land-pattern and solder recommendations, including lead pitch, body width, and exposed termination geometry. Inspect the final assembly for solder bridges across the closely spaced SOIC leads, especially around reset and programming nets. If the board operates near motors, relays, LEDs, or switching regulators, route the clock and sensitive control paths away from high-current edges and provide local return paths to reduce noise-induced resets or programming faults.
Informações de conformidade
The manufacturer datasheet states that the ATtiny25/45/85 family was verified during product qualification to AEC-Q100 grade 1. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status are unknown for the exact ordering variant.