Vishay Intertechnology

DG271AK - 4-Channel 50Ω SPST Analog Switch | Vishay

MPN: DG271AK ✗ জীবনকালের সমাপ্তি
50 pA Id 50 Ω Rds(on) 16-CERDIP Package
সর্বনিম্ন অর্ডার পরিমাণ: 1 |

DG271AK সারাংশ

Vishay Siliconix DG271AK is a high-speed quad monolithic SPST CMOS analog switch with four independently selectable switch circuits in a 16-CERDIP through-hole package. The device provides a 1:1 signal configuration, a maximum listed on-resistance of 50 Ω, and TTL/CMOS-compatible control inputs. It is intended for routing low-frequency analog signals where low leakage, fast switching, and low charge injection are important. According to the manufacturer datasheet description, its 55 ns turn-on time supports high-speed control sequences.

An analog switch is a semiconductor device that uses control inputs to connect or disconnect signals within a circuit. Unlike a mechanical relay, it can operate rapidly without mechanical wear. The DG271AK belongs to the CMOS analog-switch hierarchy, where multiple single-pole single-throw switches provide signal routing for test systems, data-acquisition equipment, instrumentation, communications, and embedded control systems. Each channel on the DG271AK forms a 1:1 path between its corresponding input and output.

The DG271AK's four independent SPST channels allow one package to handle several routing points while reducing the number of discrete controls. Its listed 55 ns turn-on time, 5 pC charge injection, 32 Ω on-resistance feature, and 50 pA low-leakage figure support fast transitions and low disturbance on sensitive analog nodes. TTL/CMOS-compatible logic levels simplify control from common digital systems. Reduced switching glitches and fast settling times are also identified as principal device features.

Internally, the monolithic CMOS construction places four switching elements and their control functions on one integrated circuit. This architecture is appropriate when a design requires predictable signal isolation and compact routing rather than the very low resistance of a mechanical relay. The switching path is bidirectional, making the DG271AK suitable for connecting sources, amplifiers, filters, and measurement inputs where signal flow may need to be reversed or selected dynamically.

Typical uses include automated test equipment, oscilloscope and multimeter input routing, sensor multiplexing, sample-and-hold systems, communication interfaces, and industrial control modules. The 16-CERDIP package is suited to through-hole assemblies and legacy or extended-temperature equipment rather than compact surface-mount consumer products. The ceramic DIP construction provides a mechanically robust option where solder-joint reliability and insertion into through-hole sockets are priorities.

Designers should account for the 50 Ω maximum listed on-resistance when cascading switches or driving a high-impedance following stage. Keep control traces away from sensitive analog paths, provide a defined logic state during power-up, and observe the absolute maximum supply and signal voltages in the manufacturer datasheet. When replacing a switch, verify control polarity, supply voltage, channel configuration, package dimensions, and the exact pinout rather than relying only on the DG271 family name.

This product page combines the functional characteristics, package constraints, sourcing guidance, drop-in alternatives, comparison points, and practical routing considerations needed to evaluate the Vishay Siliconix DG271AK for a new analog-switch design.

এর জন্য ড্রপ-ইন বিকল্প DG271AK — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।

DG271AK/883

✅ ড্রপ-ইন
📦 16-CERDIP
Same 16-CERDIP footprint and DG271AK four-channel SPST function; qualification suffix differs, with 0 Ω nominal on-resistance difference

📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)

DG271AK সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য

Number of Circuits 4 circuits
Switch Configuration 1:1
Switch Type Quad SPST
Maximum On-Resistance 50 Ω
Featured On-Resistance 32 Ω
Turn-On Time 55 ns
Charge Injection 5 pC
Low Leakage Current 50 pA
Control Logic Compatibility TTL/CMOS compatible
অপারেটিং তাপমাত্রা -55 °C to 125 °C
প্যাকেজ 16-CERDIP
Package Pitch 7.62 mm
মাউন্টিং টাইপ Through-hole
Crosstalk -100 dB at 100 kHz
Technology Monolithic CMOS

DG271AK 7.62 mm পিন কনফিগারেশন গাইড

DG271AK (7.62 mm প্যাকেজ)-এর পিন কনফিগারেশন। পিন নম্বরিং, ফাংশন এবং সংযোগ ডায়াগ্রাম প্রস্তুতকারকের ডেটাশিটে সংজ্ঞায়িত করা আছে। সঠিক ফুটপ্রিন্ট এবং সোল্ডারিং নির্দেশিকার জন্য এটি দেখুন।

DG271AK-এর জন্য 7.62 mm প্যাকেজ পিনআউট ডায়াগ্রাম

এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি DG271AK.

দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।

সাধারণ ব্যবহার

DG271AK এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Automated Test Equipment Signal Routing, Oscilloscope and Multimeter Input Multiplexing, Sensor Signal Multiplexing, Sample-and-Hold Signal Selection, Industrial Control Module Signal Routing, Communication and Instrumentation Signal Isolation.

🖥️

Automated Test Equipment Signal Routing

The DG271AK is suited to automated test equipment that selects among several low-frequency analog paths. Four independent SPST switches in one 16-CERDIP package reduce the number of routing packages required on a relay-style test interface. A listed 55 ns turn-on time allows the controller to change paths quickly, while low 50 pA leakage helps preserve the state of high-impedance nodes between measurements. Because the maximum listed on-resistance is 50 Ω, the receiving instrument should have sufficiently high input impedance. The TTL/CMOS-compatible controls also simplify sequencing from common test-controller logic.

🔧

Oscilloscope and Multimeter Input Multiplexing

The DG271AK can route several measurement inputs into a shared oscilloscope, multimeter, or data-acquisition front end. Its four 1:1 channels support source selection without mechanically switching probe leads, and the 55 ns turn-on time allows a measurement sequence to change quickly. The 50 Ω maximum on-resistance is acceptable for many high-impedance measurement paths but should be included in source-impedance calculations. Low leakage helps avoid biasing sensitive sensors, while low charge injection limits the transient created when the control state changes.

🧩

Sensor Signal Multiplexing

The DG271AK fits multiplexers for low-frequency sensor arrays where leakage and charge injection matter more than very low path resistance. Its four SPST channels let a controller select thermocouple, resistive, or buffered sensor signals in a defined sequence. A 50 pA leakage specification helps reduce errors at high-impedance sensor nodes, and the 5 pC charge-injection value defines the switching transient that must settle before conversion. Designers should still confirm common-mode range, supply voltage, and input bias requirements before connecting a specific sensor type.

📡

Sample-and-Hold Signal Selection

The DG271AK can select one of four source signals before a sample-and-hold amplifier or analog-to-converter input. Fast turn-on and settling characteristics help minimize the interval required after selection, while low charge injection reduces control-state disturbance. The switch resistance contributes directly to settling behavior and should be considered with the capacitance of the sampling node and the input impedance of the following amplifier. The 1:1 configuration preserves signal amplitude rather than dividing it between multiple paths.

🏭

Industrial Control Module Signal Routing

The DG271AK is applicable in legacy industrial control and instrumentation modules that need programmable connections between low-level analog and control lines. Its TTL/CMOS-compatible inputs allow direct use with digital control logic, and the through-hole 16-CERDIP package supports conventional PCB assembly and socketed service arrangements. Low leakage can help preserve slow or high-impedance process signals, while the four-channel arrangement reduces routing complexity. Because the device is obsolete, long-lived machinery should receive particular attention to supply tolerances, control thresholds, and available replacement inventory.

🌐

Communication and Instrumentation Signal Isolation

The DG271AK can disconnect unwanted signal paths in instrumentation and communication interfaces that require controlled routing rather than continuous conduction. Four SPST channels allow source isolation, loop selection, or test-point control within a compact through-hole footprint. The low-leakage characteristic is beneficial when the disconnected node must remain weakly biased, and the 5 pC charge-injection value provides a basis for assessing control transients. Actual signal integrity depends on source impedance, cable capacitance, layout, and the bandwidth of the switched signal.

What is the DG271AK?
The DG271AK is a Vishay Siliconix high-speed quad monolithic SPST CMOS analog switch with four independent 1:1 switching channels. According to the manufacturer datasheet description, it is intended for applications requiring low on-resistance, low leakage, and fast switching speeds. The device is offered in a 16-CERDIP through-hole package and uses TTL/CMOS-compatible control logic.
How many switches are integrated into the DG271AK?
The DG271AK contains four independent SPST analog switches, with each channel providing a 1:1 signal path. Its product listing identifies the device as a four-circuit analog switch, while the datasheet description calls it a quad monolithic SPST CMOS part. Consolidating four channels in one package reduces control-logic and board-routing overhead in multi-node routing systems.
What is the on-resistance of the DG271AK?
The DG271AK has a 50 Ω maximum listed on-resistance in its distributor product record, and the manufacturer datasheet features identify a low rDS(on) value of 32 Ω. Exact performance depends on supply voltage and test conditions. Use the datasheet characteristic curves when the switch resistance materially affects gain, bandwidth, or input impedance.
How fast is the DG271AK?
The DG271AK has a specified turn-on time of 55 ns. This fast transition makes it suitable for automated test systems, signal-routing circuits, and instrumentation that switches between analog paths on a controlled timing schedule. The manufacturer datasheet also identifies fast settling times and reduced switching glitches as important characteristics for precise acquisition behavior.
What is the charge injection of the DG271AK?
The specified charge injection for the DG271AK is 5 pC. Charge injection creates a transient voltage step when the control input changes, which can appear as a spurious signal at a connected high-impedance node. For precision measurements, account for this step in the system timing and consider sampling the settled output after the switching transient.
Where can I download the DG271AK datasheet PDF?
The DG271AK datasheet archive page provides access to the manufacturer datasheet and its electrical characteristics. The primary technical source is the Vishay Siliconix DG271AK data sheet, while the archive page organizes the PDF for engineering review. Before schematic release, use the document’s pin-description table, absolute-maximum ratings, and characteristic curves for the final design.
Where can I find the DG271AK pinout?
The DG271AK pin assignment is defined by the pin-description diagram in the Vishay Siliconix manufacturer datasheet. The device uses a 16-CERDIP package with through-hole lead spacing of 7.62 mm. Because package family names alone do not guarantee identical pin functions, assign PCB tracks directly from the manufacturer pin table and verify the lead numbering orientation.
Is the DG271AK suitable for TTL and CMOS control systems?
Yes, the DG271AK is identified as TTL/CMOS compatible. This makes its control inputs suitable for systems using either TTL output levels or CMOS logic families. The exact input thresholds and permissible supply combinations should still be checked in the manufacturer datasheet, particularly for designs powered from unusual rail levels or nonstandard voltage thresholds.
Where can I buy the DG271AK online?
Use the Request a Quote form on this page to request the DG271AK, current availability, minimum order quantity, and lead time for the exact 16-CERDIP ordering code. The device is identified as obsolete in a distributor product record, so inventory may be limited or sourced through the remaining supply chain. Confirm the package, qualification status, and lot traceability before authorizing procurement.
What is the price of the DG271AK?
The current DG271AK price depends on quantity, package code, qualification suffix, and market availability. Use the Request a Quote form on this page for a current quotation. Because the exact MPN is listed as obsolete, a quote should also confirm whether the offered configuration is the standard DG271AK, the DG271AK/883 qualified version, or another traceable package variant.
What is the lead time for the DG271AK?
The current lead time for the DG271AK must be confirmed through the Request a Quote form on this page. The exact 16-CERDIP configuration is identified as obsolete, so lead time may vary with remaining factory inventory, screened stock, and traceability requirements. For production planning, request a quantity-specific schedule and ask the supplier to confirm the manufacturer date code and packaging condition.
Is the DG271AK currently in stock?
Stock for the exact DG271AK should be checked through the Request a Quote form on this page because availability can change as obsolete inventory is allocated. A distributor record describes the device as obsolete, making remaining supply dependent on channel inventory rather than normal production replenishment. The quotation response should identify quantity, date code, and whether the units are new or otherwise described.
What is the best drop-in replacement for the DG271AK?
The DG271AK/883 is the closest documented drop-in candidate because it retains the DG271AK device identity in a 16-CERDIP package while adding the /883 qualification designation. Its electrical difference from the standard part is the qualification treatment, so it may be acceptable for legacy or screened systems after package and pin verification. No additional pin-compatible candidates could be confirmed without guessing.
Can DG271AK/883 replace the standard DG271AK?
The DG271AK/883 can be considered as a package-compatible replacement for a DG271AK after checking the manufacturer pinout and qualification requirements. Both designations identify the DG271AK in a 16-CERDIP configuration, so the nominal package and circuit function match. The /883 suffix changes procurement or qualification intent, which may make it preferable for screened applications but unnecessary for ordinary industrial use.
What can replace the DG271AK?
The DG271AK/883 is the most supportable replacement candidate shown for the exact DG271AK family and 16-CERDIP package. It preserves the four-channel SPST topology and offers a qualified ordering option. Before substitution, verify supply voltage, control thresholds, pin functions, on-resistance, switching time, leakage, and any screening requirements against the original system design.
Is the DG271AK the same as DG271AK/883?
The DG271AK and DG271AK/883 share the base DG271AK circuit and 16-CERDIP package, but the /883 suffix identifies a distinct qualification or ordering configuration. The standard DG271AK is listed as obsolete, making the /883 version potentially useful for systems that require the qualified designation. Verify procurement traceability and every electrical limit before treating the two as interchangeable.
When should I choose the DG271AK over another analog switch?
Choose the DG271AK when a design needs four independent SPST channels, 1:1 routing, TTL/CMOS-compatible control, and a through-hole ceramic DIP package. Its 55 ns turn-on time and 50 pA leakage class make it appropriate for test, measurement, and controlled analog-routing systems. Prefer another modern device when surface-mount area, very low resistance, wider supply range, or lower power is more important.

এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা DG271AK — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।

নির্বাচন গাইড

Choose the DG271AK when an existing through-hole design requires four independent 1:1 SPST channels, TTL/CMOS-compatible controls, fast switching, and low leakage. Its 16-CERDIP construction is particularly appropriate for legacy instrumentation, automated test systems, and industrial modules that are assembled or serviced through hole. Account for the 50 Ω maximum on-resistance in precision impedance calculations and allow the connected node to settle after each control transition. Consider the DG271AK/883 when the required sourcing document is the qualified /883 configuration and its procurement conditions are acceptable. For new surface-mount designs, prioritize a current device with lower on-resistance, wider supply range, lower power consumption, or a smaller footprint rather than treating an obsolete DG271-family member as an automatic replacement.

বিকল্পের সাথে তুলনা

পারামিটার এই পণ্য DG271AK/883
Package 16-CERDIP 16-CERDIP - same package
Brand Vishay Intertechnology Vishay Intertechnology
Number of Circuits 4 4
Switch Configuration 1:1 SPST 1:1 SPST
Maximum On-Resistance 50 Ω 50 Ω
Turn-On Time 55 ns 55 ns
Charge Injection 5 pC 5 pC
Leakage Current 50 pA 50 pA
Operating Temperature -55 °C to 125 °C -55 °C to 125 °C

মূল পার্থক্যসমূহ

  • Four-channel integration reduces routing-package count (বনামSingle-channel analog switches)
  • Fast switching supports automated measurement routing (বনামMechanical relay implementations)
  • Low leakage and charge injection suit sensitive analog nodes (বনামGeneral-purpose higher-charge-injection switches)

ডিজাইন নোট

Do not substitute the DG271 family solely from the device name. Confirm the 16-CERDIP lead numbering, control polarity, supply voltage, input thresholds, and absolute-maximum signal ratings in the manufacturer datasheet. The DG271AK/883 retains the base package designation but carries a distinct qualification suffix, so procurement and qualification requirements should be confirmed separately.

Place the DG271AK close to the sources that share an analog destination and keep its control traces away from high-impedance and low-level signal paths. Route each analog path as a short, continuous trace with a nearby ground reference. The 55 ns switching edge can produce a brief transient, so the input network should limit coupling from control pins into sensitive nodes.

Include the maximum 50 Ω on-resistance when calculating source impedance, attenuation, and amplifier-input interaction. For a capacitive sampling node, the switch resistance also forms a timing element and must be considered with the following amplifier’s input impedance and bias current. Leave sufficient settling time after a control change because fast turn-on does not mean the connected node has immediately reached its final value.

Account for the 5 pC charge injection and 50 pA leakage characteristics when selecting acquisition timing and input bias arrangements. Charge injection can create a voltage step on a high-impedance node, while leakage can disturb slow sensor or measurement circuits. Use grounding, shielding, and suitable acquisition averaging techniques based on the required measurement accuracy.

কমপ্লায়েন্স তথ্য

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
লিড ফ্রি
Unknown
হ্যালোজেন ফ্রি
Unknown
কনফ্লিক্ট মিনারেলস
Unknown

No definitive RoHS, REACH, lead-free, halogen-free, or conflict-minerals statement was identified for the exact DG271AK ordering code. The DG271AK/883 designation may represent a separate qualified procurement configuration and should not be assumed to share undocumented environmental declarations.

ডেটা যাচাই করা হয়েছে: 2026-11-10 — ডেটা XAIPART-এর কম্পোনেন্ট ইঞ্জিনিয়ারিং টিম দ্বারা যাচাই ও কিউরেট করা হয়েছে

সম্পর্কিত অনুসন্ধান

DG271AK datasheet DG271AK pinout DG271AK datasheet pdf DG271AK equivalent DG271AK replacement DG271AK cross reference DG271AK 16-CERDIP DG271AK analog switch DG271AK 55 ns switching DG271AK price DG271AK stock Vishay DG271AK

সম্পর্কিত কম্পোনেন্ট ও শর্তাবলী

Vishay Intertechnology DG271AK DG271AK/883 quad SPST analog switch monolithic CMOS analog switch analog switch interface IC semiconductor 1:1 signal configuration TTL-compatible CMOS-compatible on-resistance turn-on time charge injection leakage current switching glitches fast settling time 16-CERDIP ceramic dual in-line package through-hole mounting automated test equipment signal multiplexing sample-and-hold industrial instrumentation
তাৎক্ষণিক বিলওয়াছে রেকোজিউইট
সম্পূর্ণ বিবরণ পূরণ করুন — আমাদের সেলস টিম 24 ঘণ্টার মধ্যে উত্তর দেবে
পার্ট নম্বর উৎপাদক প্যাকেজ QTY লক্ষ্যমূল্য প্রসারিত
✓
বিল প্রস্তুত করা হয়েছে!

আমরা ২৪ ঘণ্টার মধ্যে আপনার ইমেইলে প্রত্যুত্তর দেব

1
RFQ জমা হয়েছে
2
কোটেশন পাওয়া গেছে
3
অর্ডার দেওয়া হয়েছে
4
পেমেন্ট
5
শিপ করা হয়েছে
6
ডেলিভারি হয়েছে
RFQ বিবরণ দেখুন