DG271AK - 4-Channel 50Ω SPST Analog Switch | Vishay
MPN: DG271AK ✗ Akhir HidupDG271AK Ringkasan
An analog switch is a semiconductor device that uses control inputs to connect or disconnect signals within a circuit. Unlike a mechanical relay, it can operate rapidly without mechanical wear. The DG271AK belongs to the CMOS analog-switch hierarchy, where multiple single-pole single-throw switches provide signal routing for test systems, data-acquisition equipment, instrumentation, communications, and embedded control systems. Each channel on the DG271AK forms a 1:1 path between its corresponding input and output.
The DG271AK's four independent SPST channels allow one package to handle several routing points while reducing the number of discrete controls. Its listed 55 ns turn-on time, 5 pC charge injection, 32 Ω on-resistance feature, and 50 pA low-leakage figure support fast transitions and low disturbance on sensitive analog nodes. TTL/CMOS-compatible logic levels simplify control from common digital systems. Reduced switching glitches and fast settling times are also identified as principal device features.
Internally, the monolithic CMOS construction places four switching elements and their control functions on one integrated circuit. This architecture is appropriate when a design requires predictable signal isolation and compact routing rather than the very low resistance of a mechanical relay. The switching path is bidirectional, making the DG271AK suitable for connecting sources, amplifiers, filters, and measurement inputs where signal flow may need to be reversed or selected dynamically.
Typical uses include automated test equipment, oscilloscope and multimeter input routing, sensor multiplexing, sample-and-hold systems, communication interfaces, and industrial control modules. The 16-CERDIP package is suited to through-hole assemblies and legacy or extended-temperature equipment rather than compact surface-mount consumer products. The ceramic DIP construction provides a mechanically robust option where solder-joint reliability and insertion into through-hole sockets are priorities.
Designers should account for the 50 Ω maximum listed on-resistance when cascading switches or driving a high-impedance following stage. Keep control traces away from sensitive analog paths, provide a defined logic state during power-up, and observe the absolute maximum supply and signal voltages in the manufacturer datasheet. When replacing a switch, verify control polarity, supply voltage, channel configuration, package dimensions, and the exact pinout rather than relying only on the DG271 family name.
This product page combines the functional characteristics, package constraints, sourcing guidance, drop-in alternatives, comparison points, and practical routing considerations needed to evaluate the Vishay Siliconix DG271AK for a new analog-switch design.
Alternatif penggantian untuk DG271AK — paket yang sama, pin-pada-pin kompatibel. Bagian paket yang berbeda memerlukan kerja ulang PCB diabaikan.
DG271AK/883
✅ Drop-In📋 Alternatif referensi (tidak dalam katalog)
DG271AK Rating Maksimal & Karakteristik Listrik
| Number of Circuits | 4 circuits |
| Switch Configuration | 1:1 |
| Switch Type | Quad SPST |
| Maximum On-Resistance | 50 Ω |
| Featured On-Resistance | 32 Ω |
| Turn-On Time | 55 ns |
| Charge Injection | 5 pC |
| Low Leakage Current | 50 pA |
| Control Logic Compatibility | TTL/CMOS compatible |
| Suhu Kerja | -55 °C to 125 °C |
| Paket | 16-CERDIP |
| Package Pitch | 7.62 mm |
| Tipe Mounting | Through-hole |
| Crosstalk | -100 dB at 100 kHz |
| Technology | Monolithic CMOS |
DG271AK 7.62 mm Diamant Konfigurasi Panduan
Konfigurasi pin untuk DG271AK (7.62 mm pakai pakai). Penomoran pin, fungsi, dan diagram koneksi ditetapkan dalam datasheet produsen. Lihatnya untuk footprint dan pedoman perpindahan paruh.
Tidak ada data diatribut pin yang tersedia untuk DG271AK.
Lihat ke: datasheet produk untuk konfigurasi pin penuh.
Aplikasi Umum
DG271AK cocok untuk 6 aplikasis: Automated Test Equipment Signal Routing, Oscilloscope and Multimeter Input Multiplexing, Sensor Signal Multiplexing, Sample-and-Hold Signal Selection, Industrial Control Module Signal Routing, Communication and Instrumentation Signal Isolation.
Automated Test Equipment Signal Routing
The DG271AK is suited to automated test equipment that selects among several low-frequency analog paths. Four independent SPST switches in one 16-CERDIP package reduce the number of routing packages required on a relay-style test interface. A listed 55 ns turn-on time allows the controller to change paths quickly, while low 50 pA leakage helps preserve the state of high-impedance nodes between measurements. Because the maximum listed on-resistance is 50 Ω, the receiving instrument should have sufficiently high input impedance. The TTL/CMOS-compatible controls also simplify sequencing from common test-controller logic.
Direkomendasikan
Oscilloscope and Multimeter Input Multiplexing
The DG271AK can route several measurement inputs into a shared oscilloscope, multimeter, or data-acquisition front end. Its four 1:1 channels support source selection without mechanically switching probe leads, and the 55 ns turn-on time allows a measurement sequence to change quickly. The 50 Ω maximum on-resistance is acceptable for many high-impedance measurement paths but should be included in source-impedance calculations. Low leakage helps avoid biasing sensitive sensors, while low charge injection limits the transient created when the control state changes.
Direkomendasikan
Sensor Signal Multiplexing
The DG271AK fits multiplexers for low-frequency sensor arrays where leakage and charge injection matter more than very low path resistance. Its four SPST channels let a controller select thermocouple, resistive, or buffered sensor signals in a defined sequence. A 50 pA leakage specification helps reduce errors at high-impedance sensor nodes, and the 5 pC charge-injection value defines the switching transient that must settle before conversion. Designers should still confirm common-mode range, supply voltage, and input bias requirements before connecting a specific sensor type.
Direkomendasikan
Sample-and-Hold Signal Selection
The DG271AK can select one of four source signals before a sample-and-hold amplifier or analog-to-converter input. Fast turn-on and settling characteristics help minimize the interval required after selection, while low charge injection reduces control-state disturbance. The switch resistance contributes directly to settling behavior and should be considered with the capacitance of the sampling node and the input impedance of the following amplifier. The 1:1 configuration preserves signal amplitude rather than dividing it between multiple paths.
Direkomendasikan
Industrial Control Module Signal Routing
The DG271AK is applicable in legacy industrial control and instrumentation modules that need programmable connections between low-level analog and control lines. Its TTL/CMOS-compatible inputs allow direct use with digital control logic, and the through-hole 16-CERDIP package supports conventional PCB assembly and socketed service arrangements. Low leakage can help preserve slow or high-impedance process signals, while the four-channel arrangement reduces routing complexity. Because the device is obsolete, long-lived machinery should receive particular attention to supply tolerances, control thresholds, and available replacement inventory.
Direkomendasikan
Communication and Instrumentation Signal Isolation
The DG271AK can disconnect unwanted signal paths in instrumentation and communication interfaces that require controlled routing rather than continuous conduction. Four SPST channels allow source isolation, loop selection, or test-point control within a compact through-hole footprint. The low-leakage characteristic is beneficial when the disconnected node must remain weakly biased, and the 5 pC charge-injection value provides a basis for assessing control transients. Actual signal integrity depends on source impedance, cable capacitance, layout, and the bandwidth of the switched signal.
Direkomendasikan
Ringkasan Produk Direkomendasikan
Data referensi engineering untuk DG271AK — pembandingan, panduan desain, dan informasi konformitas.
Panduan Pemilihan
Pembandingan dengan Alternatif
| Parameter Umum | Produk Ini | DG271AK/883 |
|---|---|---|
| Package | 16-CERDIP | 16-CERDIP - same package |
| Brand | Vishay Intertechnology | Vishay Intertechnology |
| Number of Circuits | 4 | 4 |
| Switch Configuration | 1:1 SPST | 1:1 SPST |
| Maximum On-Resistance | 50 Ω | 50 Ω |
| Turn-On Time | 55 ns | 55 ns |
| Charge Injection | 5 pC | 5 pC |
| Leakage Current | 50 pA | 50 pA |
| Operating Temperature | -55 °C to 125 °C | -55 °C to 125 °C |
Diferensiator Kunci
- Four-channel integration reduces routing-package count (vsSingle-channel analog switches)
- Fast switching supports automated measurement routing (vsMechanical relay implementations)
- Low leakage and charge injection suit sensitive analog nodes (vsGeneral-purpose higher-charge-injection switches)
Catatan Desain
Do not substitute the DG271 family solely from the device name. Confirm the 16-CERDIP lead numbering, control polarity, supply voltage, input thresholds, and absolute-maximum signal ratings in the manufacturer datasheet. The DG271AK/883 retains the base package designation but carries a distinct qualification suffix, so procurement and qualification requirements should be confirmed separately.
Place the DG271AK close to the sources that share an analog destination and keep its control traces away from high-impedance and low-level signal paths. Route each analog path as a short, continuous trace with a nearby ground reference. The 55 ns switching edge can produce a brief transient, so the input network should limit coupling from control pins into sensitive nodes.
Include the maximum 50 Ω on-resistance when calculating source impedance, attenuation, and amplifier-input interaction. For a capacitive sampling node, the switch resistance also forms a timing element and must be considered with the following amplifier’s input impedance and bias current. Leave sufficient settling time after a control change because fast turn-on does not mean the connected node has immediately reached its final value.
Account for the 5 pC charge injection and 50 pA leakage characteristics when selecting acquisition timing and input bias arrangements. Charge injection can create a voltage step on a high-impedance node, while leakage can disturb slow sensor or measurement circuits. Use grounding, shielding, and suitable acquisition averaging techniques based on the required measurement accuracy.
Informasi Konformitas
No definitive RoHS, REACH, lead-free, halogen-free, or conflict-minerals statement was identified for the exact DG271AK ordering code. The DG271AK/883 designation may represent a separate qualified procurement configuration and should not be assumed to share undocumented environmental declarations.