Texas Instruments

DS90LT012AQMFE - 400 Mbps Automotive LVDS Receiver | Texas Instruments

MPN: DS90LT012AQMFE ✓ সক্রিয়
3 V to 3.6 V Vdss 9 mA Id 5-pin SOT-23 Package
সর্বনিম্ন অর্ডার পরিমাণ: 1 |

DS90LT012AQMFE সারাংশ

The Texas Instruments DS90LT012AQMFE is a single-channel automotive LVDS differential line receiver with data rates exceeding 400 Mbps (200 MHz), a 3.3 V single-supply design, and an integrated 100 ohm typical line-termination resistor. It is packaged in the 5-pin SOT-23 surface-mount package for compact point-to-point links.

An LVDS line receiver is an interface IC that converts a low-voltage differential signal into a single-ended CMOS output. The DS90LT012AQMFE accepts differential inputs of 350 mV typical and supports ANSI TIA/EIA-644-A signaling. Its hierarchy runs from a differential line receiver to an LVDS interface, then to a high-speed serial-interface IC and, ultimately, a communications or automotive electronic system.

Key characteristics include a 3 V to 3.6 V supply range, an automotive temperature range of -40 °C to +125 °C, and AEC-Q100 Grade 1 qualification. The integrated termination resistor removes the need for a discrete point-to-point termination. Switching rates above 400 Mbps, 100 ps typical differential skew, and a 3.5 ns maximum propagation delay make the receiver suitable for high-speed clock and data distribution.

The receiver translates the differential LVDS input into a 3 V CMOS output level. Differential signaling rejects common-mode noise carried by the cable, while the receiver's controlled skew and bounded propagation delay support reliable transmission over balanced interconnects. Its single-receiver architecture is suited to systems where one link receives data from a transmitter located on another circuit card or chassis.

Typical applications include automotive infotainment and instrument-cluster links, industrial control cabinets, backplane interconnects, and high-speed clock distribution. The device is also appropriate for consumer and telecom equipment requiring a low-power LVDS-to-CMOS bridge with minimal board area and a compact 5-pin footprint.

When laying out the receiver, treat the IN+ and IN+ pins as a tightly matched, impedance-controlled differential pair and route them away from switching nodes. Confirm that the system design requires onboard termination; removing or overriding the integrated 100 ohm resistor changes the termination strategy and can impair signal integrity.

This page combines manufacturer specifications, package and interface details, lifecycle information, drop-in alternatives, and practical PCB guidance. It also highlights where the DS90LT012AQMFE fits relative to closely related receivers and clarifies the trade-offs between automotive qualification, packaging, and supply-chain variants.

এর জন্য ড্রপ-ইন বিকল্প DS90LT012AQMFE — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।

DS90LT012AQMFE/NOPB

✅ ড্রপ-ইন
📦 SOT-23-5
Same 5-pin SOT-23 LVDS receiver and 3 V to 3.6 V supply; ordering suffix differs without changing the stated electrical function

📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)

DS90LT012AQMFE/NO

✅ ড্রপ-ইন
📦 SOT-23-5
Same 5-pin SOT-33 footprint and receiver specifications; /NO denotes a different ordering or sourcing configuration

📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)

DS90LT012AQMF

✅ ড্রপ-ইন
📦 SOT-23-5
Same DS90LT012AQ 5-pin SOT-23 receiver with 400 Mbps data rate, 3 V to 3.6 V supply, and AEC-Q100 qualification; ordering suffix differs

📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)

DS90LT012AQ-Q1

✅ ড্রপ-ইন
📦 SOT-23-5
Automotive family designation with the same 3.3 V operation, 400 Mbps-plus rate, integrated 100 ohm termination, and 5-pin SOT-23 interface

📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)

DS90LT012A

✅ ড্রপ-ইন
📦 SOT-23-5
Same DS90LT012A 3 V LVDS single CMOS differential receiver; automotive grade and exact orderable suffix must be confirmed for qualification equivalence

📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)

DS90LT012AQMFE বিশেষণ

Device Type Single LVDS differential line receiver
Number of Receivers 1
ডেটা রেট >400 Mbps (200 MHz)
Supply Voltage Range 3 V to 3.6 V
Input Differential Voltage 350 mV typical
Output Level 3 V CMOS
Integrated Line Termination 100 ohm typical
Differential Skew 100 ps typical
Maximum Propagation Delay 3.5 ns
অপারেটিং তাপমাত্রার পরিসর -40 °C to +125 °C
Automotive Qualification AEC-Q100 Grade 1
Standard Compatibility ANSI TIA/EIA-644-A
প্যাকেজ 5-pin SOT-23
মাউন্টিং টাইপ Surface mount
সাপ্লাই কারেন্ট 9 mA
Power-Down Control High-Z output on power down

DS90LT012AQMFE পিন কনফিগারেশন

SOT-23-5 Package Pinout Diagram SOT-23-5 5-pin surface mount IC, JEDEC MO-178. Pin 1 by dot. 1 2 3 4 5 SOT-23-5
পিন 1 VCC — Single 3.3 V power supply input
পিন 2 IN+ — Non-inverting LVDS differential input
পিন 3 IN- — Inverting LVDS differential input
পিন 4 GND — Ground connection
পিন 5 GND — Ground connection

সাধারণ ব্যবহার

DS90LT012AQMFE এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Automotive Infotainment LVDS Link, Instrument Cluster Display Interface, Industrial Control Cabinet Data Link, Backplane Clock Distribution, High-Speed Test and Measurement Front End, Low-Power Telemetry Interface.

🚗

Automotive Infotainment LVDS Link

The DS90LT012AQMFE fits point-to-point links between an automotive infotainment head unit and an external display or control module. Its 400 Mbps-plus data rate supports high-resolution video and control traffic, while the 350 mV typical differential input matches LVDS signaling. The integrated 100 ohm typical termination reduces board complexity for a cable or harness connection. Automotive-grade temperature capability and AEC-Q100 Grade 1 qualification support its use in a vehicle environment.

🚗

Instrument Cluster Display Interface

Use the DS90LT012AQMFE when a cluster display receives high-speed data from a central vehicle computing unit. The 3.5 ns maximum propagation delay and 100 ps typical differential skew help maintain alignment between data and clock, while differential reception suppresses common-mode noise picked up from vehicle wiring. Its -40 °C to +125 °C range covers cabin temperature extremes, and the compact SOT-23 footprint leaves board space for graphics processing and storage.

🏭

Industrial Control Cabinet Data Link

The receiver can bridge an LVDS signal from a remote controller or I/O module into a 3 V CMOS logic domain inside an industrial control cabinet. Its 400 Mbps-plus capability supports high-speed transfer while the integrated termination suits a dedicated point-to-point cable. The -40 °C to +125 °C operating range covers industrial environments with temperature variation. Designers should still control connector discontinuities and route the differential pair away from switching power nodes.

🖥️

Backplane Clock Distribution

The DS90LT012AQMFE is suitable for recovering a low-power differential clock at a card edge and converting it to a CMOS clock for downstream logic. Data rates above 400 Mbps and 100 ps typical differential skew support high-speed clock transport, while the 3.5 ns maximum propagation delay provides a bounded timing relationship. The integrated 100 ohm typical line termination simplifies end-of-line termination, provided the backplane topology matches the device's intended point-to-point application.

🔧

High-Speed Test and Measurement Front End

Instrumentation requiring a compact receiver for differential test signals can use the DS90LT012AQMFE to convert LVDS into 3 V CMOS logic. The 400 Mbps-plus rate accommodates high-bandwidth digitized measurements, and the integrated termination reduces the external component count on point-to-point fixtures. The device does not replace the analog front end or perform differential-to-single-ended signal conditioning beyond its LVDS receiver function, so gain, filtering, and anti-aliasing stages must be designed separately.

🌐

Low-Power Telemetry Interface

The DS90LT012AQMFE is appropriate for a compact telemetry module that receives a clock or command stream over a balanced LVDS cable. Its 9 mA supply current and single 3.3 V architecture help limit system power, while the differential input improves noise immunity over long interconnects. The 5-pin SOT-23 package provides a small land pattern, and the integrated 100 ohm typical termination supports a dedicated transmitter-to-receiver connection without an external termination resistor.

সুপারিশকৃত পণ্যের সারসংক্ষেপ

DS90LV011AQ Companion LVDS line driver ব্যবহৃত হয়: Automotive Infotainment LVDS Link, Instrument Cluster Display Interface, Industrial Control Cabinet Data Link, Backplane Clock Distribution, High-Speed Test and Measurement Front End, Low-Power Telemetry Interface
What is the DS90LT012AQMFE?
The DS90LT012AQMFE is a Texas Instruments single-channel automotive LVDS differential line receiver that converts a low-voltage differential input into a 3 V CMOS output. It supports data rates above 400 Mbps (200 MHz), operates from a single 3.3 V supply, and is packaged in a 5-pin SOT-23. According to the manufacturer datasheet, the device also includes a 100 ohm typical integrated line-termination resistor for point-to-point links.
What is the operating voltage of DS90LT012AQMFE?
The DS90LT012AQMFE operates from 3 V to 3.6 V. The manufacturer identifies it as a single 3.3 V supply design, and its CMOS output is specified at 3 V levels. Use this supply range when designing the receiver, including tolerance for automotive or industrial supply variation. Related SOT-23 LVDS receivers may use a similar 3.3 V rail, but the DS90LT012AQMFE must be checked against the full 3 V to 3.6 V operating window.
How fast is the DS90LT012AQMFE?
The DS90LT012AQMFE supports switching rates in excess of 400 Mbps, corresponding to 200 MHz. The manufacturer datasheet also specifies 100 ps typical differential skew and a 3.5 ns maximum propagation delay. These figures make the receiver suitable for high-speed differential clock and data links, provided that the PCB interconnect, connector, and transmitter maintain the required LVDS signal integrity.
Does DS90LT012AQMFE need an external termination resistor?
No external line-termination resistor is normally required for a point-to-point link because the DS90LT012AQMFE integrates a 100 ohm typical termination resistor. This simplifies board layout and reduces component count. Before fitting an additional resistor, confirm the actual receiver configuration and trace topology; adding termination in parallel with the internal resistor can lower the effective impedance and degrade the received signal.
Is DS90LT012AQMFE automotive qualified?
Yes. The DS90LT012AQMFE is identified as an automotive LVDS receiver with AEC-Q100 Grade 1 qualification and an operating temperature range of -40 °C to +125 °C. Those characteristics suit vehicle cabin or body-electronics environments where temperature extremes and qualification traceability matter. For a design that requires only commercial-grade parts, confirm the exact ordering option and qualification grade before releasing the BOM.
Where can I download the DS90LT012AQMFE datasheet?
The manufacturer datasheet is available through the Texas Instruments product documentation, with the automotive PDF hosted at the official TI DS90LT012AQ-Q1 document address. The document covers the 350 mV typical differential input, 400 Mbps-plus data rate, 100 ps typical differential skew, 3.5 ns maximum propagation delay, integrated termination, and the -40 °C to +125 °C operating range. Use the manufacturer's pin-description table when assigning PCB nets.
Where can I find the DS90LT012AQMFE pinout?
The DS90LT012AQMFE pinout is published in the Texas Instruments DS90LT012AQ datasheet as a 5-pin SOT-23 connection diagram. The receiver uses one supply pin, two differential input pins, and ground-return pins. Because exposed-pad and thermal-pad conventions differ between SOT-23 and larger packages, follow the exact drawing associated with the ordered device rather than applying a generic SOT-23 numbering rule.
What is the best drop-in replacement for DS90LT012AQMFE?
The closest drop-in choices are the TI DS90LT012AQMFE/NOPB, DS90LT012AQMFE/NO, DS90LT012AQMF, and related DS90LT012AQ orderable variants that retain the 5-pin SOT-23 footprint, 3.3 V supply, LVDS input, and CMOS output. Verify the qualification grade and ordering suffix before substitution because some options represent lead-free, traceable, or customer-specific procurement configurations rather than different electrical functions.
Can DS90LT012AQMFE/NOPB replace DS90LT012AQMFE?
Yes, DS90LT012AQMFE/NOPB is the closest ordering-option substitute for DS90LT012AQMFE and is identified as the same 5-pin SOT-23 LVDS receiver with a 3 V to 3.6 V supply and a -40 °C to +125 °C range. The NOPB suffix denotes the specific procurement configuration rather than a different receiver architecture. Confirm automotive qualification and assembly requirements against the current manufacturer ordering information before committing the substitution.
What can replace DS90LT012AQMFE?
A replacement should preserve the 5-pin SOT-23 footprint, 3 V to 3.6 V supply range, differential LVDS input, CMOS output, and approximately 100 ohm integrated termination. The TI DS90LT012AQMFE/NOPB, DS90LT012AQMFE/NO, and DS90LT012AQMF orderable variants are the closest choices because they remain within the same receiver family. A receiver using a different package or lacking the integrated termination resistor is not a direct drop-in substitution.
DS90LT012AQMFE vs DS90LT012AQMFE/NOPB - which one should I choose?
Both devices describe the same DS90LT012AQ automotive LVDS receiver family in a 5-pin SOT-23 package, but their orderable suffixes serve different procurement needs. The NOPB version is listed with a standard catalog ordering designation, while other suffixes can indicate traceable or specialized supply configurations. Choose the option whose qualification documents, packing requirements, and lifecycle commitment match the production program rather than assuming the suffixes change the pinout.
When should I choose DS90LT012AQMFE instead of another LVDS receiver?
Choose the DS90LT012AQMFE when the design requires one LVDS receiver in a compact 5-pin SOT-23 footprint, a 3.3 V supply, operation from -40 °C to +125 °C, and onboard point-to-point termination. Its 400 Mbps-plus capability and 3.5 ns maximum propagation delay suit high-speed links. Select a different family member only when you need multiple channels, a different termination arrangement, or a package with more pins.
Is DS90LT012AQMFE suitable for automotive infotainment links?
Yes, the DS90LT012AQMFE is suitable for automotive infotainment and other in-vehicle high-speed links when the system design complies with the AEC-Q100 Grade 1 qualification and -40 °C to +125 °C operating limits. Its integrated 100 ohm typical termination is particularly useful for point-to-point cabling. The transmitter, connector, cable, and PCB routing must also satisfy the same LVDS signal-integrity requirements for reliable operation.
Where can I buy DS90LT012AQMFE online?
Use the Request a Quote form on this page to request current pricing, stock confirmation, minimum order quantity, and lead time for DS90LT012AQMFE. Because transactional availability changes by region and order volume, confirm the exact suffix, packaging, and quantity with the supplier before placing an order. The manufacturer part-details page is the appropriate starting point for checking approved orderable configurations.
What is the lead time for DS90LT012AQMFE?
Current lead time depends on the selected ordering suffix, factory inventory, and requested quantity. Submit the required quantity, target date, and packaging preference through the Request a Quote form on this page to obtain a current commitment. For production planning, treat the manufacturer product page and the distributor listing for the exact suffix as the sources to verify active status, stock, and delivery scheduling.

এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা DS90LT012AQMFE — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।

নির্বাচন গাইড

Choose the DS90LT012AQMFE for a compact point-to-point LVDS receiver design that requires AEC-Q100 Grade 1 automotive qualification, operation from -40 °C to +125 °C, data rates above 400 Mbps, and onboard 100 ohm typical termination. Its 5-pin SOT-23 footprint suits space-constrained infotainment, instrument-cluster, and industrial interfaces. DS90LT012AQMFE/NOPB is the closest catalog ordering option when that exact sourcing configuration matches the program. DS90LT012AQMFE/NO and DS90LT012AQMF remain practical choices when their procurement or traceability requirements fit the build. Use the base DS90LT012A only when its qualification documentation is acceptable for the deployment. None of these same-family options adds channels or changes the 5-pin interface, so a different receiver family is required if the design needs multiple channels, another termination arrangement, or a different package.

বিকল্পের সাথে তুলনা

পারামিটার এই পণ্য DS90LT012AQMFE/NOPB DS90LT012AQMFE/NO DS90LT012AQMF DS90LT012AQ-Q1 DS90LT012A
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Package SOT-23-5 SOT-23-5 - same SOT-23-5 - same SOT-23-5 - same SOT-23-5 - same SOT-23-5 - same
Device Type Single LVDS differential line receiver Single LVDS differential line receiver Single LVDS differential line receiver Single LVDS differential line receiver Single LVDS differential line receiver Single LVDS differential line receiver
Number of Receivers 1 1 1 1 1 1
Data Rate >400 Mbps (200 MHz) >400 Mbps (200 MHz) >400 Mbps (200 MHz) 400 Mbps >400 Mbps (200 MHz) >400 Mbps (200 MHz)
Supply Voltage Range 3 V to 3.6 V 3 V to 3.6 V 3 V to 3.6 V 3 V to 3.6 V 3 V to 3.6 V 3 V
Integrated Line Termination 100 ohm typical 100 ohm typical 100 ohm typical 100 ohm typical 100 ohm typical 100 ohm typical
Maximum Propagation Delay 3.5 ns 3.5 ns 3.5 ns 3.5 ns 3.5 ns 3.5 ns
Operating Temperature Range -40 °C to +125 °C -40 °C to +125 °C -40 °C to +125 °C -40 °C to +125 °C -40 °C to +125 °C -40 °C to +125 °C

মূল পার্থক্যসমূহ

  • Automotive-grade temperature capability (বনামDS90LT012A)
  • Integrated termination reduces board complexity (বনামLVDS receivers without integrated termination)
  • High data rate in a compact footprint (বনামDS90LT012AQMFE/NOPB)
  • Defined differential timing performance (বনামGeneral-purpose CMOS input devices)

ডিজাইন নোট

Route IN+ and IN- as a tightly coupled differential pair with continuous reference-plane support, symmetric geometry, and no stubs. Keep the pair away from switching regulators, relay drivers, clock trees, and high-current return paths. Place the receiver close to the connector or cable entry point so that the unbalanced portion of the route is minimized. Differential routing is essential because the receiver relies on the voltage difference between the two inputs rather than on either signal referenced directly to ground.

Do not add an external 100 ohm termination resistor across the receiver inputs unless the selected topology requires it and the effect on the internal termination has been verified. Doing so can place two 100 ohm terminations in parallel and create an effective 50 ohm load that increases reflections and reduces signal margin. Confirm whether the link is point-to-point, bus, or externally terminated, and use the manufacturer's application guidance for the intended connection.

The DS90LT012AQMFE operates from a single 3.3 V supply within a 3 V to 3.6 V range and draws approximately 9 mA. Place a local high-frequency bypass capacitor close to the supply pin and connect both ground pins directly to the ground plane. Keep the input pair and ground-return path short, since connector and cable return currents can share board traces with the receiver return and degrade common-mode performance.

Validate the complete link rather than relying only on the receiver datasheet: the transmitter amplitude, edge rate, cable loss, connector geometry, PCB impedance, and termination method all affect eye opening. The receiver accepts a 350 mV typical differential input, but adequate voltage at the pins depends on the complete interconnect. Use an oscilloscope or protocol analyzer to verify differential voltage and timing at the receiver when the link margin is limited.

কমপ্লায়েন্স তথ্য

RoHS
Unknown
REACH
Unknown
AEC-Q100
Qualified
লিড ফ্রি
Unknown
হ্যালোজেন ফ্রি
Unknown
কনফ্লিক্ট মিনারেলস
Unknown

The manufacturer documentation identifies the DS90LT012AQ device as AEC-Q100 Grade 1 qualified and compatible with ANSI TIA/EIA-644-A. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not established for the exact ordering option and remain unknown.

ডেটা যাচাই করা হয়েছে: 2026-11-16 — ডেটা XAIPART-এর কম্পোনেন্ট ইঞ্জিনিয়ারিং টিম দ্বারা যাচাই ও কিউরেট করা হয়েছে

সম্পর্কিত অনুসন্ধান

ds90lt012aqmfe nopb DS90LT012AQMFE datasheet DS90LT012AQMFE pinout DS90LT012AQMFE datasheet pdf Texas Instruments DS90LT012AQMFE DS90LT012AQMFE equivalent DS90LT012AQMFE replacement DS90LT012AQMFE cross reference DS90LT012AQMFE vs DS90LT012AQMFE/NOPB DS90LT012AQMFE 400 Mbps receiver DS90LT012AQMFE SOT-23-5 DS90LT012AQMFE automotive LVDS DS90LT012AQMFE price DS90LT012AQMFE integrated termination

সম্পর্কিত কম্পোনেন্ট ও শর্তাবলী

Texas Instruments DS90LT012AQMFE DS90LT012AQMFE/NOPB DS90LT012AQ DS90LT012AQ-Q1 DS90LV011AQ LVDS Low Voltage Differential Signaling differential line receiver interface IC high-speed serial interface CMOS output 3.3 V supply SOT-23-5 surface-mount package AEC-Q100 Grade 1 ANSI TIA/EIA-644-A RoHS REACH integrated line termination differential skew propagation delay point-to-point link automotive infotainment
তাৎক্ষণিক বিলওয়াছে রেকোজিউইট
সম্পূর্ণ বিবরণ পূরণ করুন — আমাদের সেলস টিম 24 ঘণ্টার মধ্যে উত্তর দেবে
পার্ট নম্বর উৎপাদক প্যাকেজ QTY লক্ষ্যমূল্য প্রসারিত
✓
বিল প্রস্তুত করা হয়েছে!

আমরা ২৪ ঘণ্টার মধ্যে আপনার ইমেইলে প্রত্যুত্তর দেব

1
RFQ জমা হয়েছে
2
কোটেশন পাওয়া গেছে
3
অর্ডার দেওয়া হয়েছে
4
পেমেন্ট
5
শিপ করা হয়েছে
6
ডেলিভারি হয়েছে
RFQ বিবরণ দেখুন