DS90LT012AQMFE - 400 Mbps Automotive LVDS Receiver | Texas Instruments
MPN: DS90LT012AQMFE ✓ Hoạt độngDS90LT012AQMFE Tóm tắt
An LVDS line receiver is an interface IC that converts a low-voltage differential signal into a single-ended CMOS output. The DS90LT012AQMFE accepts differential inputs of 350 mV typical and supports ANSI TIA/EIA-644-A signaling. Its hierarchy runs from a differential line receiver to an LVDS interface, then to a high-speed serial-interface IC and, ultimately, a communications or automotive electronic system.
Key characteristics include a 3 V to 3.6 V supply range, an automotive temperature range of -40 °C to +125 °C, and AEC-Q100 Grade 1 qualification. The integrated termination resistor removes the need for a discrete point-to-point termination. Switching rates above 400 Mbps, 100 ps typical differential skew, and a 3.5 ns maximum propagation delay make the receiver suitable for high-speed clock and data distribution.
The receiver translates the differential LVDS input into a 3 V CMOS output level. Differential signaling rejects common-mode noise carried by the cable, while the receiver's controlled skew and bounded propagation delay support reliable transmission over balanced interconnects. Its single-receiver architecture is suited to systems where one link receives data from a transmitter located on another circuit card or chassis.
Typical applications include automotive infotainment and instrument-cluster links, industrial control cabinets, backplane interconnects, and high-speed clock distribution. The device is also appropriate for consumer and telecom equipment requiring a low-power LVDS-to-CMOS bridge with minimal board area and a compact 5-pin footprint.
When laying out the receiver, treat the IN+ and IN+ pins as a tightly matched, impedance-controlled differential pair and route them away from switching nodes. Confirm that the system design requires onboard termination; removing or overriding the integrated 100 ohm resistor changes the termination strategy and can impair signal integrity.
This page combines manufacturer specifications, package and interface details, lifecycle information, drop-in alternatives, and practical PCB guidance. It also highlights where the DS90LT012AQMFE fits relative to closely related receivers and clarifies the trade-offs between automotive qualification, packaging, and supply-chain variants.
Bộ thay thế dễ dàng lắp đặt cho DS90LT012AQMFE — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
DS90LT012AQMFE/NOPB
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
DS90LT012AQMFE/NO
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
DS90LT012AQMF
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
DS90LT012AQ-Q1
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
DS90LT012A
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
DS90LT012AQMFE Thông số kỹ thuật
| Device Type | Single LVDS differential line receiver |
| Number of Receivers | 1 |
| Tốc độ dữ liệu | >400 Mbps (200 MHz) |
| Supply Voltage Range | 3 V to 3.6 V |
| Input Differential Voltage | 350 mV typical |
| Output Level | 3 V CMOS |
| Integrated Line Termination | 100 ohm typical |
| Differential Skew | 100 ps typical |
| Maximum Propagation Delay | 3.5 ns |
| Khoảng nhiệt độ hoạt động | -40 °C to +125 °C |
| Automotive Qualification | AEC-Q100 Grade 1 |
| Standard Compatibility | ANSI TIA/EIA-644-A |
| Hộp | 5-pin SOT-23 |
| Kiểu lắp đặt | Surface mount |
| Điện áp cung cấp | 9 mA |
| Power-Down Control | High-Z output on power down |
Cấu hình chân DS90LT012AQMFE
| Chân 1 | VCC — Single 3.3 V power supply input |
| Chân 2 | IN+ — Non-inverting LVDS differential input |
| Chân 3 | IN- — Inverting LVDS differential input |
| Chân 4 | GND — Ground connection |
| Chân 5 | GND — Ground connection |
Ứng dụng tiêu biểu
DS90LT012AQMFE phù hợp cho 6 Áp dụngs: Automotive Infotainment LVDS Link, Instrument Cluster Display Interface, Industrial Control Cabinet Data Link, Backplane Clock Distribution, High-Speed Test and Measurement Front End, Low-Power Telemetry Interface.
Automotive Infotainment LVDS Link
The DS90LT012AQMFE fits point-to-point links between an automotive infotainment head unit and an external display or control module. Its 400 Mbps-plus data rate supports high-resolution video and control traffic, while the 350 mV typical differential input matches LVDS signaling. The integrated 100 ohm typical termination reduces board complexity for a cable or harness connection. Automotive-grade temperature capability and AEC-Q100 Grade 1 qualification support its use in a vehicle environment.
Được đề xuất
Instrument Cluster Display Interface
Use the DS90LT012AQMFE when a cluster display receives high-speed data from a central vehicle computing unit. The 3.5 ns maximum propagation delay and 100 ps typical differential skew help maintain alignment between data and clock, while differential reception suppresses common-mode noise picked up from vehicle wiring. Its -40 °C to +125 °C range covers cabin temperature extremes, and the compact SOT-23 footprint leaves board space for graphics processing and storage.
Được đề xuất
Industrial Control Cabinet Data Link
The receiver can bridge an LVDS signal from a remote controller or I/O module into a 3 V CMOS logic domain inside an industrial control cabinet. Its 400 Mbps-plus capability supports high-speed transfer while the integrated termination suits a dedicated point-to-point cable. The -40 °C to +125 °C operating range covers industrial environments with temperature variation. Designers should still control connector discontinuities and route the differential pair away from switching power nodes.
Được đề xuất
Backplane Clock Distribution
The DS90LT012AQMFE is suitable for recovering a low-power differential clock at a card edge and converting it to a CMOS clock for downstream logic. Data rates above 400 Mbps and 100 ps typical differential skew support high-speed clock transport, while the 3.5 ns maximum propagation delay provides a bounded timing relationship. The integrated 100 ohm typical line termination simplifies end-of-line termination, provided the backplane topology matches the device's intended point-to-point application.
Được đề xuất
High-Speed Test and Measurement Front End
Instrumentation requiring a compact receiver for differential test signals can use the DS90LT012AQMFE to convert LVDS into 3 V CMOS logic. The 400 Mbps-plus rate accommodates high-bandwidth digitized measurements, and the integrated termination reduces the external component count on point-to-point fixtures. The device does not replace the analog front end or perform differential-to-single-ended signal conditioning beyond its LVDS receiver function, so gain, filtering, and anti-aliasing stages must be designed separately.
Được đề xuất
Low-Power Telemetry Interface
The DS90LT012AQMFE is appropriate for a compact telemetry module that receives a clock or command stream over a balanced LVDS cable. Its 9 mA supply current and single 3.3 V architecture help limit system power, while the differential input improves noise immunity over long interconnects. The 5-pin SOT-23 package provides a small land pattern, and the integrated 100 ohm typical termination supports a dedicated transmitter-to-receiver connection without an external termination resistor.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho DS90LT012AQMFE — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | DS90LT012AQMFE/NOPB | DS90LT012AQMFE/NO | DS90LT012AQMF | DS90LT012AQ-Q1 | DS90LT012A |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | SOT-23-5 | SOT-23-5 - same | SOT-23-5 - same | SOT-23-5 - same | SOT-23-5 - same | SOT-23-5 - same |
| Device Type | Single LVDS differential line receiver | Single LVDS differential line receiver | Single LVDS differential line receiver | Single LVDS differential line receiver | Single LVDS differential line receiver | Single LVDS differential line receiver |
| Number of Receivers | 1 | 1 | 1 | 1 | 1 | 1 |
| Data Rate | >400 Mbps (200 MHz) | >400 Mbps (200 MHz) | >400 Mbps (200 MHz) | 400 Mbps | >400 Mbps (200 MHz) | >400 Mbps (200 MHz) |
| Supply Voltage Range | 3 V to 3.6 V | 3 V to 3.6 V | 3 V to 3.6 V | 3 V to 3.6 V | 3 V to 3.6 V | 3 V |
| Integrated Line Termination | 100 ohm typical | 100 ohm typical | 100 ohm typical | 100 ohm typical | 100 ohm typical | 100 ohm typical |
| Maximum Propagation Delay | 3.5 ns | 3.5 ns | 3.5 ns | 3.5 ns | 3.5 ns | 3.5 ns |
| Operating Temperature Range | -40 °C to +125 °C | -40 °C to +125 °C | -40 °C to +125 °C | -40 °C to +125 °C | -40 °C to +125 °C | -40 °C to +125 °C |
Bảo phân biệt quan trọng
- Automotive-grade temperature capability (vsDS90LT012A)
- Integrated termination reduces board complexity (vsLVDS receivers without integrated termination)
- High data rate in a compact footprint (vsDS90LT012AQMFE/NOPB)
- Defined differential timing performance (vsGeneral-purpose CMOS input devices)
Ghi chú thiết kế
Route IN+ and IN- as a tightly coupled differential pair with continuous reference-plane support, symmetric geometry, and no stubs. Keep the pair away from switching regulators, relay drivers, clock trees, and high-current return paths. Place the receiver close to the connector or cable entry point so that the unbalanced portion of the route is minimized. Differential routing is essential because the receiver relies on the voltage difference between the two inputs rather than on either signal referenced directly to ground.
Do not add an external 100 ohm termination resistor across the receiver inputs unless the selected topology requires it and the effect on the internal termination has been verified. Doing so can place two 100 ohm terminations in parallel and create an effective 50 ohm load that increases reflections and reduces signal margin. Confirm whether the link is point-to-point, bus, or externally terminated, and use the manufacturer's application guidance for the intended connection.
The DS90LT012AQMFE operates from a single 3.3 V supply within a 3 V to 3.6 V range and draws approximately 9 mA. Place a local high-frequency bypass capacitor close to the supply pin and connect both ground pins directly to the ground plane. Keep the input pair and ground-return path short, since connector and cable return currents can share board traces with the receiver return and degrade common-mode performance.
Validate the complete link rather than relying only on the receiver datasheet: the transmitter amplitude, edge rate, cable loss, connector geometry, PCB impedance, and termination method all affect eye opening. The receiver accepts a 350 mV typical differential input, but adequate voltage at the pins depends on the complete interconnect. Use an oscilloscope or protocol analyzer to verify differential voltage and timing at the receiver when the link margin is limited.
Thông tin tuân thủ
The manufacturer documentation identifies the DS90LT012AQ device as AEC-Q100 Grade 1 qualified and compatible with ANSI TIA/EIA-644-A. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not established for the exact ordering option and remain unknown.