Texas Instruments

DS90LV032AW-MLS - 400Mbps Quad LVDS Receiver | Texas Instruments

MPN: DS90LV032AW-MLS ✓ সক্রিয়
3.3 V Vdss 16-pin CFP (NAD) Package
সর্বনিম্ন অর্ডার পরিমাণ: 1 |

DS90LV032AW-MLS সারাংশ

The Texas Instruments DS90LV032AW-MLS is a 3 V LVDS quad CMOS differential line receiver supporting data rates above 400 Mbps, equivalent to a 200 MHz switching rate, in a 16-pin CFP (NAD) package. It accepts four differential LVDS inputs and converts them to 3 V CMOS outputs, with a typical differential input voltage of 350 mV and an operating temperature range from -55°C to +85°C.

An LVDS receiver is an interface circuit that detects a small differential voltage across a balanced signal pair and converts it into a logic-level output. LVDS belongs to the differential data-interface hierarchy, where low-amplitude, noise-resistant signaling supports reliable high-speed data transfer over circuit-board interconnects. The DS90LV032A family therefore belongs to interface ICs, low-voltage differential signaling receivers, and high-speed CMOS interface devices.

The primary features of this quad receiver include four differential receiver channels, support for data rates in excess of 400 Mbps, a typical input sensitivity of 350 mV, and CMOS output signaling. The device is designed for high-speed point-to-point links where differential signaling reduces susceptibility to common-mode noise. Its quad-channel organization also allows one package to terminate four independent data pairs.

The DS90LV032A architecture uses low-power CMOS circuitry to translate the small-amplitude LVDS inputs into full-swing CMOS outputs. According to the Texas Instruments datasheet, the family supports propagation delay of up to 3.3 ns and includes low channel-to-channel and differential skew characteristics. This combination is useful when timing margins are limited, particularly in parallel data buses, backplanes, and clock-distribution networks.

Typical applications include LVDS backplanes, industrial control links, high-speed instrumentation, point-to-point inter-board communication, and data-acquisition systems that require multiple low-voltage differential inputs. The device can receive data from compatible LVDS transmitters over controlled-impedance printed circuit board traces. Because it is a receiver rather than a transceiver, each channel still requires an external LVDS source and correctly terminated signal pair.

PCB implementation must preserve controlled impedance, minimize stubs, and route each differential pair as a tightly coupled pair. Inputs should not be left floating when the receiver is powered, and the power-supply network should be decoupled close to the device. Because CFP packages are not represented by the available package-diagram library, the manufacturer pin-description table should be used when assigning PCB tracks.

This product page combines the exact DS90LV032AW-MLS ordering information with receiver specifications, package details, drop-in alternatives, application guidance, and design considerations. The comparison information is intended to clarify temperature grade, packaging, and ordering differences before a component is selected for a high-speed LVDS interface.

এর জন্য ড্রপ-ইন বিকল্প DS90LV032AW-MLS — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।

DS90LV032AW-QML

✅ ড্রপ-ইন
📦 16-pin CFP (NAD)
Related QML ordering option with the same quad-LVDS function and 16-pin CFP format; temperature-grade and package-drawing details must be confirmed before substitution

📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)

DS90LV032AWGQML

✅ ড্রপ-ইন
📦 16-pin CFP (NAD)
Related GQML ordering option with the same quad-LVDS function and 16-pin CFP format; qualification and suffix-specific conditions may differ

📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)

DS90LV032AW-MLS বিশেষণ

Product Type LVDS quad differential line receiver
Logic Family CMOS
সাপ্লাই ভোল্টেজ 3.3 V
Maximum Data Rate >400 Mbps
Maximum Switching Rate 200 MHz
Receiver Channel Count 4 channels
Typical Differential Input Voltage 350 mV
Maximum Propagation Delay 3.3 ns
Typical Channel-to-Channel Skew 0.1 ns
Typical Differential Skew 0.1 ns
Static Power Consumption 40 mW at 3.3 V
Power-Down Input Behavior High impedance on LVDS inputs
অপারেটিং তাপমাত্রার পরিসর -55°C to +85°C
প্যাকেজ 16-pin CFP (NAD)
মাউন্টিং টাইপ Surface mount
Terminal Count 16 pins

DS90LV032AW-MLS 16-pin cfp (nad) পিন কনফিগারেশন গাইড

DS90LV032AW-MLS (16-pin cfp (nad) প্যাকেজ)-এর পিন কনফিগারেশন। পিন নম্বরিং, ফাংশন এবং সংযোগ ডায়াগ্রাম প্রস্তুতকারকের ডেটাশিটে সংজ্ঞায়িত করা আছে। সঠিক ফুটপ্রিন্ট এবং সোল্ডারিং নির্দেশিকার জন্য এটি দেখুন।

DS90LV032AW-MLS-এর জন্য 16-pin cfp (nad) প্যাকেজ পিনআউট ডায়াগ্রাম

এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি DS90LV032AW-MLS.

দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।

সাধারণ ব্যবহার

DS90LV032AW-MLS এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: High-Speed Backplane Links, Industrial Control Systems, Data-Acquisition Equipment, Point-to-Point Inter-Board Communication, Clock and Parallel Data Distribution, Test and Measurement Interfaces.

🌐

High-Speed Backplane Links

The DS90LV032AW-MLS is suitable for receiving high-speed LVDS data over controlled-impedance backplane traces. Its four differential channels support data rates in excess of 400 Mbps, while the typical 350 mV input threshold accommodates the small-amplitude signals used by LVDS links. A board designer can connect each receiver channel to a matched differential pair, add the termination required by the link architecture, and route the pair with minimal discontinuity. The principal benefit is the combination of four receivers and a maximum propagation delay of 3.3 ns in one 16-pin CFP package, which simplifies multi-lane termination and helps preserve timing margin across a backplane.

🏭

Industrial Control Systems

The DS90LV032AW-MLS can serve as the receive interface for industrial equipment that distributes commands or measurements across multiple LVDS links. Its -55°C to +85°C temperature rating supports equipment expected to operate across wide environmental conditions, while the 400 Mbps data-rate capability is well above ordinary control-command rates. Four differential inputs allow independent channels to share one receiver package without introducing a separate IC for each link. The receiver should be used with a compatible LVDS transmitter, correct source termination, and a ground reference that keeps common-mode voltage within the device limits. Firmware designers should account for the specified propagation delay when defining communication timeouts and bus turnaround intervals.

🖥️

Data-Acquisition Equipment

The DS90LV032AW-MLS is appropriate for data-acquisition and instrumentation systems in which several high-speed differential channels feed digital processing logic. Four independent LVDS inputs reduce the number of receiver packages required on a measurement card, while the typical 350 mV differential input amplitude is compatible with standard LVDS signaling. The receiver produces CMOS outputs that can be routed to an FPGA, microcontroller, or data-capture engine after the entire signal path has been validated. Designers should preserve controlled-impedance routing, avoid long stubs, and account for the 3.3 ns maximum propagation delay when defining acquisition timing. The -55°C to +85°C range also supports industrial and extended-temperature measurement equipment.

🔧

Point-to-Point Inter-Board Communication

The DS90LV032AW-MLS supports compact inter-board communication links where a transmitting device sends low-voltage differential data to the receiver. Data rates above 400 Mbps provide margin for synchronous transfers, and the four-channel configuration allows several point-to-point connections to terminate on one receiver device. A practical implementation requires matched trace geometry, reference-plane continuity, and the termination strategy specified for the particular LVDS transmitter. The receiver's 3.3 V supply and CMOS output levels integrate naturally with 3.3 V digital logic, provided the receiving logic recognizes the resulting output timing. Compared with single-ended links, differential reception reduces susceptibility to common-mode noise when the PCB layout is implemented correctly.

🧩

Clock and Parallel Data Distribution

The DS90LV032AW-MLS can receive multiple synchronized differential signals in clock-distribution and parallel-data systems. Its typical channel-to-channel skew and differential skew characteristics are useful when several lanes must reach downstream logic with closely related timing. Because the device supports data rates above 400 Mbps, it can accommodate source-synchronous clock and data pairs transmitted across a controlled-impedance board connection. The four receiver outputs become CMOS signals for downstream gates or controllers, while the maximum propagation delay of 3.3 ns defines an important edge-timing limit. Layout should minimize trace-length differences within each pair, provide a continuous reference plane, and isolate the links from switching-node and high-current return paths.

🔬

Test and Measurement Interfaces

The DS90LV032AW-MLS is useful in test and measurement equipment that receives differential data from remote sensor heads, detector modules, or instrument front ends. Four channels allow compact multi-lane acquisition, and the specified 3.3 ns maximum propagation delay provides a defined upper bound for digital timing analysis. The extended -55°C to +85°C rating supports laboratory, industrial, and monitored field environments when the complete equipment has been qualified for the same range. For reliable results, the receiver must remain connected to a defined common-mode range and properly terminated source. PCB designers should keep the receiver away from noisy analog return paths and use short, symmetrical routing between the connector or sensor interface and the CFP package inputs.

সুপারিশকৃত পণ্যের সারসংক্ষেপ

DS90LV032A Base device family for the quad LVDS receiver ব্যবহৃত হয়: High-Speed Backplane Links, Industrial Control Systems, Data-Acquisition Equipment, Clock and Parallel Data Distribution, Test and Measurement Interfaces DS90LV032AW-QML Related 16-pin CFP ordering option ব্যবহৃত হয়: High-Speed Backplane Links, Point-to-Point Inter-Board Communication, Clock and Parallel Data Distribution DS90LV032AWGQML Related 16-pin CFP family option ব্যবহৃত হয়: Industrial Control Systems, Point-to-Point Inter-Board Communication, Test and Measurement Interfaces DS90LV032AW-MLS Texas Instruments ব্যবহৃত হয়: Data-Acquisition Equipment
What is DS90LV032AW-MLS?
The DS90LV032AW-MLS is a Texas Instruments quad CMOS differential receiver designed for 3.3 V LVDS signals above 400 Mbps. According to the Texas Instruments DS90LV032A datasheet, it accepts four differential inputs with a typical amplitude of 350 mV and converts them to CMOS outputs. The device is packaged in a 16-pin CFP (NAD) package and is rated from -55°C to +85°C.
What is the maximum data rate of DS90LV032AW-MLS?
The DS90LV032AW-MLS supports data rates in excess of 400 Mbps, corresponding to a switching rate above 200 MHz. This performance makes the receiver appropriate for high-speed point-to-point LVDS links, parallel data buses, and backplane connections. The operating limits and test conditions are defined by the Texas Instruments DS90LV032A datasheet.
Where can I download the DS90LV032AW-MLS datasheet PDF?
The official DS90LV032AW-MLS datasheet is the DS90LV032A datasheet published by Texas Instruments. It can be downloaded from the manufacturer link on this page and contains the electrical characteristics, receiver descriptions, package information, and pin descriptions. The document also identifies the DS90LV032AW-MLS ordering configuration as a 16-pin CFP (NAD) device rated from -55°C to +85°C.
Where can I find the DS90LV032AW-MLS pinout?
The DS90LV032AW-MLS pin assignments are listed in the pin-description table of the Texas Instruments DS90LV032A datasheet. The component uses a 16-pin CFP (NAD) package with four differential receiver channels. Use the manufacturer pin table and package drawing for PCB layout because the CFP package diagram is not represented in the package library used by this page.
Is DS90LV032AW-MLS suitable for 3.3 V LVDS interfaces?
Yes, the DS90LV032AW-MLS is designed for 3.3 V LVDS interfaces and translates differential LVDS inputs into 3 V CMOS outputs. Its typical accepted differential input voltage is 350 mV, while the supported data rate exceeds 400 Mbps. This makes it suitable for 3.3 V systems using compatible LVDS transmitters and controlled-impedance interconnects.
Where can I buy DS90LV032AW-MLS online?
Use the Request a Quote form on this page to request DS90LV032AW-MLS availability, current pricing, minimum order quantity, and lead time. The exact ordering code is a 16-pin CFP (NAD) device from Texas Instruments rated from -55°C to +85°C. A written quote allows the package, quantity, and delivery requirements to be confirmed together before an order is placed.
What is the price of DS90LV032AW-MLS?
The current DS90LV032AW-MLS price is shown through the Request a Quote form on this page. Market pricing can change with quantity, procurement volume, and component availability, so the form provides the most appropriate way to obtain a current quotation. The confirmed order should identify the exact DS90LV032AW-MLS ordering code and 16-pin CFP package.
What is the lead time and stock status for DS90LV032AW-MLS?
Use the Request a Quote form on this page to confirm current DS90LV032AW-MLS stock, minimum order quantity, and production lead time. The component is identified as a Texas Instruments 16-pin CFP device for operation from -55°C to +85°C. A current quote is necessary because supply status and scheduling can change independently of the product specification.
What is the difference between DS90LV032AW-MLS and DS90LV032AW-QML?
DS90LV032AW-MLS is the 16-pin CFP configuration rated from -55°C to +85°C, while DS90LV032AW-QML is identified as a related 16-pin CFPAK ordering option. Both belong to the DS90LV032A receiver family and support the same stated 400 Mbps class of signaling. Confirm the exact package drawing, temperature grade, and ordering suffix before substituting one for the other.
When should I choose DS90LV032AW-MLS over another LVDS receiver?
Choose DS90LV032AW-MLS when the design requires four 3.3 V LVDS differential inputs, a data rate above 400 Mbps, a 16-pin CFP package, and operation across -55°C to +85°C. Select a different ordering option only when its package, temperature rating, supply details, and pin functions match the intended board. The receiver is appropriate for LVDS sources, not ordinary single-ended CMOS inputs.
Is DS90LV032AW-MLS suitable for backplane and industrial control links?
Yes, the DS90LV032AW-MLS fits high-speed backplane and industrial control links that use compatible 3.3 V LVDS signaling. Its four differential channels, typical 350 mV input sensitivity, and data-rate capability above 400 Mbps support reliable point-to-point communication. The PCB must use controlled-impedance routing and appropriate source and termination networks for the complete LVDS interface.
What can replace DS90LV032AW-MLS?
DS90LV032AW-QML and DS90LV032AWGQML are the closest documented drop-in candidates in the same Texas Instruments receiver family. Both use a 16-pin CFP-style package and share the DS90LV032A function, but the package drawing, temperature grade, and suffix markings must be checked before replacement. Only alternatives with identical pin functions and confirmed board-level requirements should be substituted.
What is the best cross-brand equivalent for DS90LV032AW-MLS?
No cross-brand equivalent is established for the DS90LV032AW-MLS because the available cross-reference information does not identify a candidate with a confirmed 16-pin CFP footprint and equivalent pin functions. A functional LVDS receiver alone is not a drop-in substitute. The board should be evaluated against the manufacturer pin table, power requirements, input thresholds, propagation delay, and package drawings before selecting another manufacturer.
How should DS90LV032AW-MLS be laid out for reliable LVDS operation?
Route every LVDS pair as a tightly coupled, controlled-impedance differential pair with minimal stubs and symmetric length matching. Place power-supply decoupling capacitors close to the device and follow the manufacturer grounding and pin-description guidance. According to the Texas Instruments datasheet, the receiver accepts a typical 350 mV differential signal, so incorrect pair geometry, termination, or source amplitude can impair signal integrity.
What are the key specifications of DS90LV032AW-MLS?
The key specifications are four differential LVDS receiver channels, a 3.3 V supply, support for data rates above 400 Mbps, a 200 MHz switching-rate class, and a typical 350 mV differential input amplitude. The Texas Instruments DS90LV032A datasheet also specifies up to 3.3 ns propagation delay and a -55°C to +85°C operating range. The package is 16-pin CFP (NAD).

এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা DS90LV032AW-MLS — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।

নির্বাচন গাইড

Choose the DS90LV032AW-MLS when a design needs four 3.3 V LVDS differential inputs, operation above 400 Mbps, a 16-pin CFP package, and an extended -55°C to +85°C temperature rating. It is especially suitable for controlled-impedance backplanes, industrial links, data-acquisition equipment, and point-to-point inter-board connections. DS90LV032AW-QML and DS90LV032AWGQML are related same-brand candidates, but their exact temperature grade, package marking, and qualification conditions must be confirmed before substitution. Do not select a generic cross-brand LVDS receiver unless its footprint, pin functions, supply requirements, input sensitivity, output levels, timing, and temperature range all match. The main design trade-off is that the CFP package is less convenient than a modern leaded or exposed-pad package, so the receiver is best used where an existing 16-pin CFP footprint and long-life industrial or aerospace-style procurement requirements justify that package choice.

বিকল্পের সাথে তুলনা

পারামিটার এই পণ্য DS90LV032AW-QML DS90LV032AWGQML
Brand Texas Instruments Texas Instruments Texas Instruments
Package 16-pin CFP (NAD) 16-pin CFP (NAD) 16-pin CFP (NAD)
Receiver Type Quad CMOS differential LVDS line receiver Quad CMOS differential LVDS line receiver Quad CMOS differential LVDS line receiver
Channel Count 4 channels 4 channels 4 channels
Maximum Data Rate >400 Mbps >400 Mbps >400 Mbps
Maximum Switching Rate >200 MHz >200 MHz >200 MHz
Typical Differential Input Voltage 350 mV 350 mV 350 mV
Maximum Propagation Delay 3.3 ns 3.3 ns 3.3 ns
Supply Voltage 3.3 V 3.3 V 3.3 V
Ordering Code DS90LV032AW-MLS DS90LV032AW-QML DS90LV032AWGQML

মূল পার্থক্যসমূহ

  • Extended-temperature ordering configuration (বনামDS90LV032AW-QML)
  • Four high-speed differential channels in one package (বনামDS90LV032AWGQML)
  • Low propagation delay for high-speed LVDS reception (বনামDS90LV032AW-QML)

ডিজাইন নোট

Route each LVDS signal as a tightly coupled differential pair over a continuous reference plane. Match the pair geometry to the PCB stack-up's intended differential impedance, minimize vias and stubs, and keep the two conductors within the length tolerance required by the link. Do not route LVDS pairs adjacent to switching-node traces or high-current return paths, because even a small differential signal can be corrupted by common-mode noise coupled into the receiver inputs.

Use the termination arrangement specified by the connected LVDS transmitter and system architecture rather than adding an arbitrary resistor at the receiver. The DS90LV032AW-MLS accepts a typical differential input voltage of 350 mV, but correct signal amplitude also depends on source impedance, cable or PCB loss, and termination. Validate input eye margin, differential skew, and propagation-delay behavior in the final assembled board rather than relying only on schematic simulation.

Provide a stable 3.3 V supply and place the required decoupling capacitors close to the device power and ground pins. Keep the supply-return path short and use a continuous ground reference beneath the receiver and its associated routing. The receiver's static power is low, but external LVDS drivers and the switched load on the same rail can create transient current; separating noisy supply paths from the receiver reduces noise coupling into the high-speed interface.

Do not select a receiver merely because it uses LVDS or has the same number of channels. Confirm that the alternative uses the same 16-pin CFP footprint, pin functions, supply voltage, input threshold, output logic levels, and temperature range. Before substituting DS90LV032AW-QML or DS90LV032AWGQML, compare the manufacturer ordering table, package drawing, and pin-description table. A footprint match without equivalent pin functions is not a usable drop-in replacement.

কমপ্লায়েন্স তথ্য

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
লিড ফ্রি
Unknown
হ্যালোজেন ফ্রি
Unknown
কনফ্লিক্ট মিনারেলস
Unknown

The DS90LV032AW-MLS is identified as a Texas Instruments military-temperature product in a 16-pin CFP (NAD) package. Specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals declarations require confirmation from the manufacturer product documentation.

ডেটা যাচাই করা হয়েছে: 2026-11-16 — ডেটা XAIPART-এর কম্পোনেন্ট ইঞ্জিনিয়ারিং টিম দ্বারা যাচাই ও কিউরেট করা হয়েছে

সম্পর্কিত অনুসন্ধান

DS90LV032AW-MLS datasheet DS90LV032AW-MLS pinout DS90LV032AW-MLS datasheet pdf DS90LV032AW-MLS equivalent DS90LV032AW-MLS replacement DS90LV032AW-MLS cross reference DS90LV032AW-MLS vs DS90LV032AW-QML DS90LV032AW-MLS footprint DS90LV032AW-MLS price DS90LV032AW-MLS stock Texas Instruments DS90LV032AW-MLS DS90LV032A 400Mbps LVDS receiver

সম্পর্কিত কম্পোনেন্ট ও শর্তাবলী

Texas Instruments DS90LV032AW-MLS DS90LV032A DS90LV032AW-QML DS90LV032AWGQML LVDS Low Voltage Differential Signaling differential line receiver quad CMOS receiver interface IC high-speed data interface 3.3 V CMOS output 400 Mbps data rate 350 mV differential input 3.3 ns propagation delay 16-pin CFP NAD package surface-mount package controlled-impedance routing industrial control data acquisition backplane communication RoHS REACH AEC-Q100
তাৎক্ষণিক বিলওয়াছে রেকোজিউইট
সম্পূর্ণ বিবরণ পূরণ করুন — আমাদের সেলস টিম 24 ঘণ্টার মধ্যে উত্তর দেবে
পার্ট নম্বর উৎপাদক প্যাকেজ QTY লক্ষ্যমূল্য প্রসারিত
✓
বিল প্রস্তুত করা হয়েছে!

আমরা ২৪ ঘণ্টার মধ্যে আপনার ইমেইলে প্রত্যুত্তর দেব

1
RFQ জমা হয়েছে
2
কোটেশন পাওয়া গেছে
3
অর্ডার দেওয়া হয়েছে
4
পেমেন্ট
5
শিপ করা হয়েছে
6
ডেলিভারি হয়েছে
RFQ বিবরণ দেখুন