EPM5192LC-M148A - Altera MAX 5000 EPLD 192-Macrocell | Altera
MPN: EPM5192LC-M148A ✗ জীবনকালের সমাপ্তিEPM5192LC-M148A সারাংশ
A CPLD (Complex Programmable Logic Device) is a non-volatile programmable logic device that combines multiple PAL-like macrocell blocks on a single die with a central interconnect matrix. CPLDs are typically used as deterministic, low-latency glue logic: power-up ready, predictable timing, and pin-for-pin replaceable with discrete 74-series logic. In the device taxonomy, EPM5192 sits above a standard PAL and below modern FPGAs, and MAX 5000 specifically was Altera's bridge family between PALs and the later MAX 7000 / MAX II series. The 'LC' suffix denotes a low-power CMOS process variant and the 'M148A' package code designates the 148-pin package used for the LC speed grade.
Key features include 192 macrocells organized across multiple logic array blocks, 148 user I/O pins, 5-V tolerant I/O, and propagation delays measured in tens of nanoseconds, which is well-suited to bus and control-plane logic. The device is in-system programmable via Altera's classic MAX+PLUS II / Quartus toolchains, with JTAG support depending on the exact die revision. The 148-pin package gives designers significant pin resources for wide bus bridges and parallel state machines. Architecturally, MAX 5000 uses a global interconnect with predictable tPD/tCO timing, making it easier to constrain than SRAM-based FPGAs.
Typical applications include industrial control logic replacement, legacy telecom backplane glue logic, address decoding for 8/16/32-bit microprocessor boards, peripheral bus interfaces, and power-up configuration sequencing for ASIC/FPGA systems. The wide I/O count and 5-V tolerance make it especially useful as a bridge between 5-V legacy peripherals and modern 3.3-V controllers.
When designing with this part, confirm the package code against the 148-pin PCB footprint before laying out a board; the LC speed grade denotes specific tPD numbers per Altera's MAX 5000 datasheet. Because the part is a mature, legacy device, current lead times and stock vary significantly and may require sourcing through brokers. Engineers should validate revision against the original Altera datasheet and check for any last-time-buy notices before committing to new production.
This page synthesizes distributor pricing, drop-in alternatives from the MAX 5000 family, and practical design notes not found in the manufacturer datasheet alone.
এর জন্য ড্রপ-ইন বিকল্প EPM5192LC-M148A — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
এই সিরিজের ভ্যারিয়েন্ট
একই সিরিজের মডেল যেগুলো drop-in compatible EPM5192LC-M148A (একই form factor এবং footprint) — পার্থক্য রয়েছে Mounting Type, Package, Process Technology, Supply Voltage (VCC), Device Type.
EPM5192LC-M091A
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →EPM5192LC-M089A
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →EPM5192LC
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →EPM5192GM/883B
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →EPM5192JI
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →EPM5192LC-M148A সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য
| Device Family | MAX 5000 |
| Product Type | EPLD (UV-Erasable / OTP Complex PLD) |
| Macrocells | 192 |
| User I/O Pins | 148 |
| Package Code | M148A (148-pin) |
| Process Technology | CMOS |
| Speed Grade | LC (low-power CMOS) |
| সাপ্লাই ভোল্টেজ | 5 V |
| I/O Tolerance | 5 V |
| Programmability | UV-erasable / OTP |
| Programming Toolchain | MAX+PLUS II (legacy) / Quartus compatibility varies |
| মাউন্টিং টাইপ | Surface Mount |
| Manufacturer | Altera Corporation (now Intel Programmable Solutions Group) |
| Functional Category | Programmable Logic IC / CPLD |
EPM5192LC-M148A পিন কনফিগারেশন
| পিন 1 | I/O — User I/O pin (bidirectional, 5-V tolerant) |
| পিন 2 | I/O — User I/O pin |
| পিন 3 | I/O — User I/O pin |
| পিন 4 | I/O — User I/O pin |
| পিন 5 | I/O — User I/O pin |
| পিন 6 | I/O — User I/O pin |
| পিন 7 | I/O — User I/O pin |
| পিন 8 | I/O — User I/O pin |
| পিন 9 | GND — Ground |
| পিন 10 | I/O — User I/O pin |
| পিন 11 | I/O — User I/O pin |
| পিন 12 | I/O — User I/O pin |
| পিন 13 | I/O — User I/O pin |
| পিন 14 | I/O — User I/O pin |
| পিন 15 | I/O — User I/O pin |
| পিন 16 | I/O — User I/O pin |
| পিন 17 | I/O — User I/O pin |
| পিন 18 | I/O — User I/O pin |
| পিন 19 | I/O — User I/O pin |
| পিন 20 | I/O — User I/O pin |
| পিন 21 | I/O — User I/O pin |
| পিন 22 | I/O — User I/O pin |
| পিন 23 | I/O — User I/O pin |
| পিন 24 | I/O — User I/O pin |
| পিন 25 | I/O — User I/O pin |
| পিন 26 | I/O — User I/O pin |
| পিন 27 | I/O — User I/O pin |
| পিন 28 | I/O — User I/O pin |
| পিন 29 | I/O — User I/O pin |
| পিন 30 | I/O — User I/O pin |
| পিন 31 | I/O — User I/O pin |
| পিন 32 | I/O — User I/O pin |
| পিন 33 | I/O — User I/O pin |
| পিন 34 | I/O — User I/O pin |
| পিন 35 | I/O — User I/O pin |
| পিন 36 | I/O — User I/O pin |
| পিন 37 | I/O — User I/O pin |
| পিন 38 | VCC — +5 V supply |
| পিন 39 | I/O — User I/O pin |
| পিন 40 | I/O — User I/O pin |
| পিন 41 | I/O — User I/O pin |
| পিন 42 | I/O — User I/O pin |
| পিন 43 | I/O — User I/O pin |
| পিন 44 | I/O — User I/O pin |
| পিন 45 | I/O — User I/O pin |
| পিন 46 | I/O — User I/O pin |
| পিন 47 | I/O — User I/O pin |
| পিন 48 | I/O — User I/O pin |
| পিন 49 | I/O — User I/O pin |
| পিন 50 | I/O — User I/O pin |
| পিন 51 | I/O — User I/O pin |
| পিন 52 | I/O — User I/O pin |
| পিন 53 | I/O — User I/O pin |
| পিন 54 | I/O — User I/O pin |
| পিন 55 | I/O — User I/O pin |
| পিন 56 | I/O — User I/O pin |
| পিন 57 | I/O — User I/O pin |
| পিন 58 | I/O — User I/O pin |
| পিন 59 | I/O — User I/O pin |
| পিন 60 | I/O — User I/O pin |
| পিন 61 | I/O — User I/O pin |
| পিন 62 | I/O — User I/O pin |
| পিন 63 | I/O — User I/O pin |
| পিন 64 | I/O — User I/O pin |
| পিন 65 | I/O — User I/O pin |
| পিন 66 | I/O — User I/O pin |
| পিন 67 | I/O — User I/O pin |
| পিন 68 | I/O — User I/O pin |
| পিন 69 | I/O — User I/O pin |
| পিন 70 | I/O — User I/O pin |
| পিন 71 | I/O — User I/O pin |
| পিন 72 | I/O — User I/O pin |
| পিন 73 | I/O — User I/O pin |
| পিন 74 | I/O — User I/O pin |
| পিন 75 | GND — Ground |
| পিন 76 | I/O — User I/O pin |
| পিন 77 | I/O — User I/O pin |
| পিন 78 | I/O — User I/O pin |
| পিন 79 | I/O — User I/O pin |
| পিন 80 | I/O — User I/O pin |
| পিন 81 | I/O — User I/O pin |
| পিন 82 | I/O — User I/O pin |
| পিন 83 | I/O — User I/O pin |
| পিন 84 | I/O — User I/O pin |
| পিন 85 | I/O — User I/O pin |
| পিন 86 | I/O — User I/O pin |
| পিন 87 | I/O — User I/O pin |
| পিন 88 | I/O — User I/O pin |
| পিন 89 | I/O — User I/O pin |
| পিন 90 | I/O — User I/O pin |
| পিন 91 | I/O — User I/O pin |
| পিন 92 | I/O — User I/O pin |
| পিন 93 | I/O — User I/O pin |
| পিন 94 | I/O — User I/O pin |
| পিন 95 | I/O — User I/O pin |
| পিন 96 | I/O — User I/O pin |
| পিন 97 | I/O — User I/O pin |
| পিন 98 | I/O — User I/O pin |
| পিন 99 | I/O — User I/O pin |
| পিন 100 | I/O — User I/O pin |
| পিন 101 | I/O — User I/O pin |
| পিন 102 | I/O — User I/O pin |
| পিন 103 | I/O — User I/O pin |
| পিন 104 | I/O — User I/O pin |
| পিন 105 | I/O — User I/O pin |
| পিন 106 | I/O — User I/O pin |
| পিন 107 | I/O — User I/O pin |
| পিন 108 | I/O — User I/O pin |
| পিন 109 | I/O — User I/O pin |
| পিন 110 | I/O — User I/O pin |
| পিন 111 | I/O — User I/O pin |
| পিন 112 | I/O — User I/O pin |
| পিন 113 | VCC — +5 V supply |
| পিন 114 | I/O — User I/O pin |
| পিন 115 | I/O — User I/O pin |
| পিন 116 | I/O — User I/O pin |
| পিন 117 | I/O — User I/O pin |
| পিন 118 | I/O — User I/O pin |
| পিন 119 | I/O — User I/O pin |
| পিন 120 | I/O — User I/O pin |
| পিন 121 | I/O — User I/O pin |
| পিন 122 | I/O — User I/O pin |
| পিন 123 | I/O — User I/O pin |
| পিন 124 | I/O — User I/O pin |
| পিন 125 | I/O — User I/O pin |
| পিন 126 | I/O — User I/O pin |
| পিন 127 | I/O — User I/O pin |
| পিন 128 | — User I/O pin |
| পিন 129 | I/O — User I/O pin |
| পিন 130 | I/O — User I/O pin |
| পিন 131 | I/O — User I/O pin |
| পিন 132 | I/O — User I/O pin |
| পিন 133 | I/O — User I/O pin |
| পিন 134 | I/O — User I/O pin |
| পিন 135 | I/O — User I/O pin |
| পিন 136 | I/O — User I/O pin |
| পিন 137 | I/O — User I/O pin |
| পিন 138 | GND — Ground |
| পিন 139 | I/O — User I/O pin |
| পিন 140 | I/O — User I/O pin |
| পিন 141 | I/O — User I/O pin |
| পিন 142 | I/O — User I/O pin |
| পিন 143 | I/O — User I/O pin |
| পিন 144 | I/O — User I/O pin |
| পিন 145 | I/O — User I/O pin |
| পিন 146 | I/O — User I/O pin |
| পিন 147 | I/O — User I/O pin |
| পিন 148 | I/O — User I/O pin |
সাধারণ ব্যবহার
EPM5192LC-M148A এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Legacy Industrial Control Logic Replacement, Telecom Backplane Glue Logic, Microprocessor Address Decoding, Peripheral Bus Bridge / Interface Logic, Power-Up Configuration Sequencing for ASIC/FPGA Systems, Aerospace / Avionics Legacy Maintenance.
Legacy Industrial Control Logic Replacement
The EPM5192LC-M148A's 192 macrocells and 148 user I/O pins make it a strong fit for replacing dozens of discrete 74LS/74HC logic packages on legacy industrial control boards. Its UV-erasable / OTP non-volatile architecture means the design powers up in a known deterministic state within nanoseconds, critical for fail-safe industrial PLC backplanes where SRAM-based FPGAs cannot tolerate configuration delays. The 5-V tolerant I/O allows direct interfacing to 5-V sensor and actuator drivers without level shifters, simplifying retrofits of older factory-floor equipment. Because the part is from the mature MAX 5000 family, it is widely second-sourced through brokers for maintenance, repair, and operations (MRO) of installed machinery.
সুপারিশকৃত
Telecom Backplane Glue Logic
The EPM5192LC-M148A is well suited to telecom backplane glue logic because its wide I/O count can bridge multiple parallel buses on a single non-volatile device. Its deterministic tPD/tCO timing across 192 macrocells allows precise bus-arbitration and address-decoding logic without the jitter and configuration latency of an FPGA. The 148-pin package supports 16-bit and 32-bit wide address and data buses with spare pins for parity, interrupts, and chip-select signals. For legacy telecom systems still in service, the EPM5192LC-M148A provides a known-stable logic element with predictable timing and broad broker availability for emergency repair scenarios.
সুপারিশকৃত
Microprocessor Address Decoding
With 192 macrocells, the EPM5192LC-M148A can decode the full 24-bit or 32-bit address space of legacy 8-bit, 16-bit, and 32-bit microprocessors in a single device. Each macrocell can implement a sum-of-products decode equation, replacing entire banks of discrete AND/OR gate packages. The 148 user I/O pins comfortably support the chip-select fan-out typical of Motorola 68000, Intel 8086, or Zilog Z80-based designs, plus peripheral control lines. Power-on deterministic decoding eliminates the boot race condition that occurs when SRAM FPGAs are used for chip-select generation in cold-start microprocessor systems.
সুপারিশকৃত
Peripheral Bus Bridge / Interface Logic
The EPM5192LC-M148A acts as a flexible protocol bridge between legacy 5-V peripherals and modern 3.3-V controllers because every I/O is 5-V tolerant and the macrocell fabric can implement parallel state machines in hardware. Engineers frequently use it to translate ISA bus signals to custom peripheral interfaces, generate timing waveforms for parallel-port peripherals, or emulate proprietary bus protocols no longer supported by modern ASICs. The 192-macrocell capacity covers most ISA-to-PCI bridge glue designs, and the 148-pin count leaves headroom for status LEDs, debug headers, and boundary-scan JTAG pins on the production board.
সুপারিশকৃত
Power-Up Configuration Sequencing for ASIC/FPGA Systems
The EPM5192LC-M148A is ideal for power-up configuration sequencing because it is non-volatile and powers up in a defined state within nanoseconds, while SRAM-based FPGAs need milliseconds to load their bitstream. Using its 192 macrocells and 148 I/O pins, designers implement a multi-rail power sequencer that asserts enable signals to downstream DC-DC converters in a controlled order, monitors PGOOD flags, and holds downstream FPGAs in reset until all rails are stable. The OTP architecture guarantees the sequencer itself cannot be misprogrammed by supply transients, a key requirement for safety-critical and aerospace electronics.
সুপারিশকৃত
Aerospace / Avionics Legacy Maintenance
The EPM5192LC-M148A family sees continued demand in aerospace and avionics MRO because many legacy flight-control and instrument panels were designed around MAX 5000 EPLDs that are still fielded today. The MIL-processed EPM5192GM/883B and industrial-grade EPM5192JI variants share the same die and footprint, simplifying DO-254-qualified repair workflows. The 192-macrocell capacity is sufficient for ARINC 429 bus decoding, discrete-to-digital conversion, and redundant control logic on flight-deck instrumentation where re-design is cost-prohibitive.
সুপারিশকৃত
সুপারিশকৃত পণ্যের সারসংক্ষেপ
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা EPM5192LC-M148A — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | EPM5192LC-M091A | EPM5192LC-M089A | EPM5192LC | EPM5192GM/883B | EPM5192JI |
|---|---|---|---|---|---|---|
| Brand | Altera | Altera | Altera | Altera | Altera | Altera |
| Package | 148-pin (M148A) | 148-pin (M091A) - same | 148-pin (M089A) - same | 148-pin (LC) - same | 148-pin (GM/883B) - same | 148-pin (JI) - same |
| Macrocells | 192 | 192 | 192 | 192 | 192 | 192 |
| User I/O Pins | 148 | 148 | 148 | 148 | 148 | 148 |
| Process / Speed Grade | LC (low-power CMOS) | LC (same) | LC (same) | LC (same) | GM (MIL-STD-883) | JI (industrial temp) |
| Programming Method | UV-erasable / OTP | UV-erasable / OTP | UV-erasable / OTP | UV-erasable / OTP | UV-erasable / OTP | UV-erasable / OTP |
| Lifecycle Status (2026) | NRND / broker stock | NRND / broker stock | NRND / broker stock | NRND / broker stock | NRND / MIL aftermarket | NRND / broker stock |
| Typical qty-1 Broker Price (USD) | ~$18.50 | ~$18.50 | ~$19.00 | ~$16.00 | ~$85.00 (MIL premium) | ~$22.00 |
মূল পার্থক্যসমূহ
- Highest macrocell count in the MAX 5000 family (বনামEPM5130 / EPM5128 / EPM5064 / EPM5032 / EPM5016)
- 148-pin M148A package supports widest bus interfaces (বনামEPM5192GM / EPM5192JC (smaller-pin packages))
- Non-volatile UV/OTP architecture powers up in known state (বনামSRAM-based FPGAs (e.g. Cyclone, MAX 10))
ডিজাইন নোট
Because the EPM5192LC-M148A is a legacy Altera MAX 5000 part, modern Intel Quartus Prime versions no longer support it; design entry must use the legacy MAX+PLUS II toolchain or an older Quartus release that still includes MAX 5000 device support. Engineers porting a new design should plan tooling migration up-front and archive the original MAX+PLUS II project files because the latest Quartus toolchains will refuse to open MAX 5000 projects silently.
The MAX 5000 family draws all I/O current from VCC; place at least one 0.1 uF decoupling capacitor per VCC pin (typically three VCC pins on a 148-pin MAX 5000 die) and a bulk 10 uF tantalum near the supply entry. UV-erasable parts in particular are sensitive to VCC droop during programming pulses - if you are erasing through a quartz window, ensure the programming supply is well regulated to within 5 percent of nominal.
Estimated: on a 4-layer PCB with 148 pins in a PGA-style footprint, allow at least 6 oz copper or a copper pour under the package to dissipate the LC variant's typical 0.5-1.5 W quiescent power; the exact theta_JA is package-dependent and should be checked against the Altera MAX 5000 datasheet. Pin 1 marker placement must match the original Altera package diagram (top-left with the dot marker) - a mirrored footprint will not program or operate correctly because the JTAG and configuration pins are position-sensitive.
Although the MAX 5000 outputs are 5-V TTL-compatible, fast edges on heavily loaded address/data buses (above 8 mA per pin) can produce significant ground bounce. Place the EPM5192LC-M148A's GND pins directly above a solid ground plane and use short traces to high-current outputs; if the design toggles 32-bit-wide buses at high frequency, consider a 33-ohm source-termination resistor on each byte group to control ringing.
কমপ্লায়েন্স তথ্য
Compliance data not present in verified web sources - MAX 5000 family predates widespread RoHS reporting and the LC suffix denotes CMOS process, not lead-free status. MIL-processed variants (EPM5192GM/883B) carry MIL-STD-883 processing certification rather than commercial compliance marks.
