ICS527R-04 - 160MHz CMOS PLL Clock Driver | Renesas
MPN: ICS527R-04 ✓ সক্রিয়ICS527R-04 সারাংশ
A PLL-based clock driver is an integrated timing device that locks an output clock to a reference and distributes that clock through configurable logic paths. The user-configurable architecture allows a design to select the division ratio and output behavior required by the receiving circuitry. In a zero-delay-buffer configuration, the device minimizes propagation delay between the driving source and downstream clock loads while preserving a defined relationship between input and output edges.
The ICS527R-04 supports a maximum frequency of 160 MHz, making it applicable to clock-generation and distribution systems operating below that limit. Its PECL input interface is intended for systems using positive emitter-coupled logic clock sources. The CMOS PLL implementation and configurable outputs provide the basis for translating a reference clock into multiple synchronized signals needed by digital logic, communications equipment, and test systems.
A principal design consideration is the relationship between input frequency, selected feedback ratio, output division, and the resulting operating point. The manufacturer datasheet should be used to confirm supported configuration combinations, output-edge relationships, supply requirements, and the treatment of unused inputs or outputs before the device is placed into production. PCB implementation must preserve the pin assignments and decoupling recommendations associated with the SSOP-28 footprint.
Typical uses include PECL-to-logic clock distribution, frequency multiplication or division within a PLL architecture, and generation of related clocks for digital subsystems. The device can also be used in communications equipment and test platforms where multiple outputs must remain synchronized. Its 0°C to 70°C commercial operating range is appropriate for indoor commercial and industrial equipment that does not require extended-temperature operation.
Engineers should verify absolute maximum ratings, recommended operating conditions, AC timing, output-drive capability, and power consumption against the manufacturer datasheet before final schematic or layout release. The SSOP-28 package provides a high pin count relative to its body size, so careful routing and stable supply decoupling are particularly important.
This page organizes the documented operating limits, package information, sourcing questions, and design considerations for ICS527R-04. It also distinguishes verified device facts from parameters that still require confirmation before a replacement or new design can be released.
এর জন্য ড্রপ-ইন বিকল্প ICS527R-04 — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
এই সিরিজের ভ্যারিয়েন্ট
একই সিরিজের মডেল যেগুলো drop-in compatible ICS527R-04 (একই form factor এবং footprint) — পার্থক্য রয়েছে Package.
এই পণ্যের জন্য কোনো ড্রপ-ইন বিকল্প পাওয়া যায়নি।
বিকল্প অনুরোধ করুনICS527R-04 বিশেষণ
| Device Type | PLL-based clock driver |
| Maximum Frequency | 160 MHz |
| Input Interface | User-configurable PECL |
| Output Function | Zero-delay buffer |
| Internal Technology | CMOS PLL |
| প্যাকেজ | SSOP-28 |
| মাউন্টিং টাইপ | Surface mount |
| অপারেটিং তাপমাত্রা | 0°C to 70°C |
| Reel Quantity | 2,500 units |
| AEC-Q100 Qualification | Not applicable |
ICS527R-04 ssop-28 পিন কনফিগারেশন গাইড
ICS527R-04 (ssop-28 প্যাকেজ)-এর পিন কনফিগারেশন। পিন নম্বরিং, ফাংশন এবং সংযোগ ডায়াগ্রাম প্রস্তুতকারকের ডেটাশিটে সংজ্ঞায়িত করা আছে। সঠিক ফুটপ্রিন্ট এবং সোল্ডারিং নির্দেশিকার জন্য এটি দেখুন।
এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি ICS527R-04.
দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।
সাধারণ ব্যবহার
ICS527R-04 এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: PECL Clock Distribution, Frequency Multiplication and Division, Telecommunications Clocking, Digital Test Equipment, Industrial Control Logic, Synchronous Data Processing.
PECL Clock Distribution
The ICS527R-04 fits PECL clock-distribution designs that require more than simple edge distribution because it combines a user-configurable PECL input with PLL-based clock generation and zero-delay-buffer functionality. Its documented maximum frequency of 160 MHz provides a defined operating ceiling for downstream logic. Use the input termination and configuration network specified by the manufacturer, then route each supported output according to the device's pin and timing tables. The zero-delay architecture is particularly useful when the design must retain a close relationship between the reference source and distributed clocks, although final timing margin must be evaluated at the receiver rather than inferred only from the device name.
সুপারিশকৃত
Frequency Multiplication and Division
The ICS527R-04 can serve as the central timing element in systems that require a reference clock to be multiplied, divided, or redistributed through a PLL-based architecture. Its maximum operating frequency of 160 MHz sets the principal design boundary, while the user-configurable nature of the device supports several clock-plan options. Engineers should derive the feedback and output settings from the manufacturer configuration table, verify that the requested output remains inside the PLL's valid operating range, and include startup and lock behavior in system timing analysis. The CMOS PLL implementation makes this device appropriate for digital subsystems requiring deterministic clock relationships.
সুপারিশকৃত
Telecommunications Clocking
ICS527R-04 is applicable to telecommunications equipment that accepts a PECL clock reference and needs configurable, synchronized clock outputs. The device's documented 160 MHz maximum frequency accommodates clocking requirements below that limit, and its PLL-based architecture can support frequency relationships that a simple fanout buffer cannot provide. Design the reference input according to the manufacturer interface requirements and keep each output's loading within its specified fanout and timing limits. Because SSOP-28 routing density can affect return paths and coupling, use a solid ground plane and place decoupling and termination close to the relevant pins.
সুপারিশকৃত
Digital Test Equipment
The configurable PLL and zero-delay-buffer behavior of the ICS527R-04 can support clock generation inside digital test and measurement systems. Such equipment often needs several related clocks for acquisition, processing, conversion, or data-transfer blocks, and a single user-configurable device can simplify the clock-plan architecture. The 160 MHz maximum frequency is suitable for systems whose internal clock targets remain below that value. Engineers should characterize setup, hold, jitter, and output-skew requirements for each timing path and reserve configuration control so operating modes can be changed safely without violating the manufacturer's PLL operating constraints.
সুপারিশকৃত
Industrial Control Logic
ICS527R-04 can be used in industrial control logic when a controller or communication block requires a PECL reference and coordinated clock outputs. Its commercial 0°C to 70°C operating range suits indoor equipment whose internal ambient remains within that interval. The PLL-based implementation supports generated clock relationships, while the zero-delay-buffer function can help preserve source-to-destination edge alignment in suitably designed systems. The design must account for supply tolerances, temperature-dependent timing, startup behavior, and the configuration state of unused outputs. Firmware or control logic should keep the clock configuration within the valid combinations listed by the manufacturer.
সুপারিশকৃত
Synchronous Data Processing
The ICS527R-04 is suitable for clocking synchronous processing pipelines where several logic domains must operate from related reference signals. Its user-configurable output behavior allows the clock architecture to be tailored more precisely than a fixed fanout device, while the documented 160 MHz ceiling defines the maximum supported operating point. Place the device close to the clock-consuming circuitry, provide low-impedance supply and ground connections, and use the pin-description table to terminate unused outputs as directed. System-level timing analysis should include worst-case PLL variation, output skew, loading, and board delay rather than relying only on nominal propagation-delay figures.
সুপারিশকৃত
সুপারিশকৃত পণ্যের সারসংক্ষেপ
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা ICS527R-04 — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য |
|---|---|
| Brand | Renesas Electronics |
| Package | SSOP-28 |
| Device Type | PLL-based clock driver |
| Maximum Frequency | 160 MHz |
| Input Interface | User-configurable PECL |
| Output Function | Zero-delay buffer |
| Internal Technology | CMOS PLL |
| Operating Temperature | 0°C to 70°C |
মূল পার্থক্যসমূহ
- Combines PECL input, PLL generation, and zero-delay buffering (বনামICS527R-02ILF)
- Documented operating ceiling (বনামICS527R-02ILF)
- Commercial-temperature operating range (বনামICS527R-02ILF)
ডিজাইন নোট
Use the manufacturer SSOP-28 pin-description table when assigning every power, ground, input, output, and configuration connection. Place the PLL reference input and clock outputs on short, direct routes, and provide a continuous ground plane beneath the device. The 28-pin SSOP footprint has closely spaced leads, so fanout and escape routing should be planned before finalizing adjacent component placement.
Place the manufacturer's recommended supply-decoupling network close to the corresponding power and ground pins, and keep clock-input return paths away from switching nodes. Confirm the supported supply range, bypass capacitance, and input termination from the datasheet before schematic release. Do not infer PECL termination values from another ICS527 configuration because interface requirements may differ.
Verify the complete feedback ratio, division ratio, output configuration, and target frequency as one valid PLL operating combination. A requested output below the 160 MHz device maximum can still be invalid if it violates the PLL's permitted input or feedback range. Also check startup, lock, unused-pin, and unused-output requirements in the manufacturer documentation before treating configuration-control pins as ordinary static logic.
Base output routing, fanout, and termination on the clock's rise and fall requirements rather than nominal operating frequency alone. Use short paths to minimize board-induced skew, maintain a continuous reference plane, and keep unused outputs in the manufacturer-recommended state. Validate setup time, hold time, and jitter at the receiving device because a valid source-edge relationship does not guarantee adequate margin at the end of the trace.
কমপ্লায়েন্স তথ্য
The available product information does not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. The documented 0°C to 70°C operating range is a temperature rating, not evidence of automotive qualification.