INA118UBG4 - Precision Instrumentation Amplifier | Texas Instruments
MPN: INA118UBG4 ✓ সক্রিয়INA118UBG4 সারাংশ
An instrumentation amplifier is a specialized amplifier category that measures a small voltage difference between two inputs while rejecting common-mode interference. The INA118 belongs to the broader precision amplifier hierarchy: instrumentation amplifier, differential amplifier, analog signal-chain IC, and semiconductor. This makes it more suitable than a general-purpose operational amplifier when the input signal is small, the source impedance is high, or the measurement environment contains substantial common-mode voltage.
Key characteristics include three internal amplifiers, a 50 µV input offset voltage, an 800 kHz bandwidth rating, low-power operation, and a single-ended output. The three-amplifier topology supports gain adjustment from approximately 1 to 10,000 according to the device family documentation. A single gain-setting resistor keeps the circuit compact and simplifies calibration. The SOIC-8 package also supports conventional surface-mount assembly and is narrower than many larger instrumentation-amplifier packages.
The INA118 architecture is intended for low-level differential measurements where offset and common-mode rejection determine accuracy. Its current-feedback input stage helps preserve usable bandwidth as gain increases. In practical systems, the external gain resistor, input filtering network, supply bypass capacitors, and grounding strategy directly affect achievable accuracy. Designers should place input filtering close to the amplifier and avoid routing sensitive input traces beside high-current switching paths.
Typical uses include bridge and strain-gauge signal conditioning, biomedical instrumentation, current-shunt measurement, sensor interfaces, battery-powered instruments, and industrial data-acquisition systems. The INA118UBG4 is particularly appropriate when a low-power, compact, precision measurement front end is required and the output can drive a single-ended downstream ADC.
A key design consideration is to verify the common-mode and output-voltage limits against the actual supply voltage and sensor signal range. Input protection, offset calibration, and reference grounding should be handled according to the manufacturer application guidance when operating near the electrical limits. The gain resistor should be placed close to the gain pin, and the layout should preserve a low-impedance return path.
This page combines manufacturer-device identity, distributor availability information, technical specifications, same-package alternatives, comparison data, and practical layout guidance for engineers evaluating the INA118UBG4.
এর জন্য ড্রপ-ইন বিকল্প INA118UBG4 — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
এই সিরিজের ভ্যারিয়েন্ট
একই সিরিজের মডেল যেগুলো drop-in compatible INA118UBG4 (একই form factor এবং footprint) — পার্থক্য রয়েছে Gain Range, Package, Input Offset Voltage, Number of Circuits, Product Type.
INA118UB
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →INA118UG4
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →INA118UB/2K5G4
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
INA118UBG4 সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য
| Product Type | Precision instrumentation amplifier |
| Manufacturer | Texas Instruments |
| Number of Amplifiers | 3 internal amplifiers |
| Input Offset Voltage | 50 µV |
| Bandwidth | 800 kHz |
| আউটপুট টাইপ | Single-ended |
| Gain Range | Approximately 1 to 10,000 |
| Gain Setting | 1 external resistor |
| প্যাকেজ | 8-pin SOIC, 3.90 mm width |
| মাউন্টিং টাইপ | Surface mount |
INA118UBG4 8-pin soic, 3.90 mm width পিন কনফিগারেশন গাইড
INA118UBG4 (8-pin soic, 3.90 mm width প্যাকেজ)-এর পিন কনফিগারেশন। এই অ্যানালগ কম্পোনেন্টে ইনপুট, আউটপুট ও পাওয়ার সাপ্লাই পিন রয়েছে। অফসেট নাল, কম্পেনসেশন ও এনেবল পিন কনফিগারেশনের জন্য প্রস্তুতকারকের ডেটাশিট দেখুন। সিগন্যাল কন্ডিশনিং ও অ্যামপ্লিফায়ার সার্কিটের জন্য আদর্শ।
এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি INA118UBG4.
দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।
সাধারণ ব্যবহার
INA118UBG4 এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Strain-Gauge Bridge Measurement, Portable Biomedical Instrumentation, Current-Shunt Measurement, Precision Sensor Signal Conditioning, Industrial Data Acquisition, Battery-Powered Measurement Systems.
Strain-Gauge Bridge Measurement
The INA118UBG4 fits strain-gauge and load-cell front ends because its 50 µV input offset specification helps preserve accuracy for small differential bridge signals. The three-amplifier architecture and gain adjustment from approximately 1 to 10,000 allow a common amplifier platform to cover different bridge sensitivities. Place the gain resistor close to the RG pin, route the two bridge returns as a differential pair, and bypass both supply pins. The principal design tradeoff is that increasing gain also narrows usable bandwidth, so filter and settling requirements should be checked against the selected gain.
সুপারিশকৃত
Portable Biomedical Instrumentation
The INA118UBG4 is appropriate for portable biomedical instrumentation that acquires weak differential sensor signals while conserving board space and power. Its low-power instrumentation-amplifier positioning, 50 µV offset specification, and 8-pin SOIC package support compact analog-front-end designs. Input impedance, bias current, common-mode range, and supply voltage must be checked for the selected electrode and sensor source. A guarded grounding layout, shielded input path, and carefully selected low-pass filter help reduce interference and motion artifacts in clinical or wellness equipment.
Current-Shunt Measurement
The INA118UBG4 can amplify the differential voltage produced by a precision current shunt in power-supply, battery, and motor-control systems. Differential input measurement rejects the common-mode voltage present across a high-side shunt, while the 800 kHz bandwidth supports faster current measurements than a slow precision-only amplifier. Confirm that the shunt common-mode voltage remains inside the device input range and that output swing suits the ADC or controller. Kelvin routing, dedicated return traces, and input filtering are important for accurate measurements above millivolt levels.
সুপারিশকৃত
Precision Sensor Signal Conditioning
The INA118UBG4 is well matched to resistive and active sensors that generate small differential outputs, including pressure cells, temperature bridges, and analog sensor front ends. The 50 µV offset rating helps minimize error before gain multiplication, while one external resistor simplifies gain configuration. Engineers should calculate expected output range at the highest sensor excitation and worst-case process variation. Place input protection away from sensitive nodes, reference the return to the sensor ground, and verify that the selected gain does not exceed the bandwidth needed by the measurement system.
Industrial Data Acquisition
The INA118UBG4 provides a compact precision front end for industrial data-acquisition cards that combine low-level sensor inputs with a single-ended ADC channel. Its 800 kHz bandwidth supports reasonably fast signal capture, and its three-amplifier topology offers more direct differential conditioning than a general-purpose op-amp circuit. The design should isolate analog and digital return paths, use separate bypass capacitors at each supply pin, and account for ADC acquisition time. A calibrated gain network is advisable when absolute measurement accuracy must remain stable over temperature and production tolerances.
Battery-Powered Measurement Systems
The INA118UBG4's low-power design makes it suitable for handheld meters, field probes, and battery-powered environmental monitors that measure low-level differential signals. The 8-pin SOIC package minimizes board area, while the 50 µV offset specification supports accurate acquisition at modest gain. System-level power depends on the selected supply voltage, quiescent current, external resistor network, and ADC load, so those values should be included in the battery budget. Avoid placing the gain resistor near switching-regulator nodes, and use a quiet ground return to preserve measurement resolution.
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা INA118UBG4 — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | INA118UB | INA118UG4 | INA118UB/2K5G4 |
|---|---|---|---|---|
| Package | 8-pin SOIC, 3.90 mm width | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Product Type | Precision low-power instrumentation amplifier | Precision instrumentation amplifier | INA118-family instrumentation amplifier | INA118-family instrumentation amplifier |
মূল পার্থক্যসমূহ
- Precision input-offset performance for low-level differential measurement (বনামINA118UB)
- Adjustable gain in a compact 8-pin SOIC instrumentation-amplifier package (বনামINA118UB/2K5G4)
- Differential measurement architecture with a single-ended output (বনামINA118UG4)
ডিজাইন নোট
Place the external gain-setting resistor directly beside the RG pin and keep the associated return path short. Route the two differential inputs as a matched pair and avoid sharing sensitive input traces with display, switching-regulator, or relay-control nets. For breadboard-style prototypes, use a dedicated instrumentation-amplifier layout; excessive breadboard capacitance and unequal lead lengths can degrade settling and common-mode rejection.
Decouple each supply pin locally with a high-frequency ceramic capacitor and provide additional bulk capacitance near the measurement section. Use short ground returns for the bypass network, and connect analog and digital return currents so they do not share a path beneath the amplifier or ADC. Before finalizing the supply design, verify the input common-mode range and output swing against the exact operating voltage.
Do not assume the 800 kHz bandwidth remains available at high gain; usable bandwidth falls as the configured gain increases. Likewise, a 50 µV input offset specification does not remove errors caused by input bias current, resistor tolerance, source impedance mismatch, or ADC reference drift. Use a matched input network and calibration strategy where measurement accuracy, rather than amplifier resolution alone, determines system performance.
কমপ্লায়েন্স তথ্য
Compliance status requires confirmation from the manufacturer product documentation or applicable declarations.