LM2202MX - 230 MHz Video Amplifier | Texas Instruments
MPN: LM2202MX ✗ জীবনকালের সমাপ্তিLM2202MX সারাংশ
A video amplifier is a specialized linear amplifier that preserves the amplitude, timing, and waveform characteristics of composite or component video signals. Within the wider signal-processing hierarchy, the LM2202MX belongs to the video amplifier and amplifier IC category, where it processes analog video signals before display encoding, raster generation, image capture, or other downstream video functions. Its 230 MHz bandwidth places it in the high-frequency class of analog video amplification rather than the audio-frequency amplifier category.
The LM2202MX provides one amplifier circuit and is identified as a standard general-purpose video amplifier. The manufacturer material identifies the device as a 230 MHz video amplifier system in a 20-SOIC package. The associated comparison information lists a supply current of 48 mA, while detailed limits for gain, input and output impedance, voltage gain, slew rate, noise, supply range, and control functions are not established by the manufacturer data available for this page.
This high-frequency architecture is particularly relevant to legacy RGB and monochrome display equipment, where source signals include transitions and timing information across a wide analog bandwidth. The 20-pin SOIC package provides a conventional surface-mount assembly option, but its relatively long leads require careful routing and adequate spacing from high-speed switching nodes. A complete board design should preserve the pin assignments and application topology shown in the manufacturer datasheet rather than infer connections from the package outline.
Typical uses include RGB monitor input cards, monochrome video display modules, video timing and sync-processing boards, industrial imaging interfaces, and retrofit or repair platforms that still use analog video. In these systems, the device can provide the wideband gain and conditioning required before a signal reaches a display controller or monitor input section. Its suitability for a particular video standard must be checked against the required bandwidth, signal levels, gain settings, and termination arrangement.
When laying out a circuit around the LM2202MX, keep high-speed video traces short, use a continuous reference plane, and maintain working clearances from clocks, switch-mode converters, and digital signals. Decoupling should follow the manufacturer recommendations, and unused amplifier inputs require the documented termination method rather than being left floating. These measures limit ringing, reduce susceptibility to coupling, and preserve the amplitude relationship between the source and the downstream video stage.
This product page combines the confirmed 230 MHz bandwidth, one-channel architecture, 20-SOIC package, source links, application context, and drop-in alternatives where verified compatibility exists. It also identifies missing electrical and environmental details instead of presenting unverified values as design data, helping engineers establish the correct manufacturer datasheet and application information before releasing a layout.
এর জন্য ড্রপ-ইন বিকল্প LM2202MX — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
এই পণ্যের জন্য কোনো ড্রপ-ইন বিকল্প পাওয়া যায়নি।
বিকল্প অনুরোধ করুনLM2202MX সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য
| Product Type | Video amplifier system |
| Amplifier Circuit Count | 1 circuit |
| Device Classification | Standard general-purpose video amplifier |
| -3 dB Bandwidth | 230 MHz |
| সাপ্লাই কারেন্ট | 48 mA |
| Package Type | 20-SOIC |
| Total Pin Count | 20 pins |
| মাউন্টিং টাইপ | Surface mount |
| Primary Application | High-resolution monochrome and RGB color monitor applications |
LM2202MX 20-soic পিন কনফিগারেশন গাইড
LM2202MX (20-soic প্যাকেজ)-এর পিন কনফিগারেশন। এই অ্যানালগ কম্পোনেন্টে ইনপুট, আউটপুট ও পাওয়ার সাপ্লাই পিন রয়েছে। অফসেট নাল, কম্পেনসেশন ও এনেবল পিন কনফিগারেশনের জন্য প্রস্তুতকারকের ডেটাশিট দেখুন। সিগন্যাল কন্ডিশনিং ও অ্যামপ্লিফায়ার সার্কিটের জন্য আদর্শ।
এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি LM2202MX.
দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।
সাধারণ ব্যবহার
LM2202MX এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: RGB Computer Monitor Input, Monochrome Monitor Signal Conditioning, Industrial Imaging Video Interface, Video Timing and Sync Processing, Legacy Monitor Repair and Replacement, Analog Video Distribution Stage.
RGB Computer Monitor Input
The LM2202MX fits legacy RGB monitor input circuitry because it is identified as a standard video amplifier system with 230 MHz -3 dB bandwidth for RGB color-monitor applications. One amplifier channel can condition an incoming red, green, or blue video path before the signal reaches the monitor's display-processing electronics. The 20-SOIC package supports conventional surface-mount assembly, although a new design must also verify the required gain, signal amplitude, supply voltage, and termination values in the manufacturer datasheet. Because the confirmed bandwidth is broad but not associated with a modern pixel-clock specification, system timing, edge response, and overall channel bandwidth should be checked together.
সুপারিশকৃত
Monochrome Monitor Signal Conditioning
The LM2202MX is suitable for legacy monochrome display modules that require wideband analog amplification ahead of a monitor controller. Its confirmed 230 MHz -3 dB bandwidth provides ample margin for many video-frequency signals, while the single-circuit architecture allows separate channels to be used for red, green, and blue or for related timing and video paths. The implementation should follow the manufacturer's reference topology, preserve the intended termination, and avoid long PCB stubs that could create reflections at video frequencies. For repaired equipment, replacing the IC alone is insufficient unless the original resistor values, supply conditions, and output loading are also reproduced.
সুপারিশকৃত
Industrial Imaging Video Interface
The LM2202MX can be used in an industrial analog-video interface when the source signals remain compatible with a 230 MHz wideband amplifier and the operating environment falls within the device's unconfirmed electrical ratings. The amplifier may condition monochrome or RGB analog video before conversion, capture, or display processing. Industrial suitability must not be inferred from bandwidth alone: supply tolerance, temperature range, electromagnetic susceptibility, availability, and product lifecycle must be reviewed. The SOIC layout should maintain a continuous ground plane and separate video traces from switching nodes, while the exact termination and gain network must follow the manufacturer application information.
সুপারিশকৃত
Video Timing and Sync Processing
The LM2202MX's 230 MHz bandwidth makes it applicable to selected high-speed analog timing or synchronization paths in legacy video equipment, subject to signal-level and gain verification. A single-channel device can process a horizontal or vertical timing signal when the rise time, amplitude, and bandwidth requirements fall within the complete datasheet specification set. Care is required around edges: very fast transitions can excite parasitic inductance, lead inductance, or capacitive loading even when the nominal video bandwidth is acceptable. Follow the manufacturer's pin configuration and recommended source and load impedances, and validate timing margin with the final cable, connector, and shielding configuration.
সুপারিশকৃত
Legacy Monitor Repair and Replacement
The LM2202MX is well suited to maintaining or replicating a legacy monitor board that originally used the LM2202 in a 20-SOIC footprint. The confirmed 230 MHz -3 dB bandwidth, one-amplifier format, and general-purpose designation align with classic monochrome and RGB video circuitry. Replacement activity should include a pin-by-pin comparison with the original device, confirmation of supply conditions, and inspection of adjacent electrolytic capacitors and coupling networks, which can age faster than the IC. For long-term production, obtain lifecycle and lot information through the Request a Quote form before committing the part to a new design.
সুপারিশকৃত
Analog Video Distribution Stage
The LM2202MX may serve as a conditioning element in a distributed analog-video path where broad bandwidth and a single dedicated amplifier channel are required. Its 230 MHz bandwidth can pass monochrome, RGB, or related high-frequency video waveforms when the source amplitude and gain requirements are compatible. Distribution networks introduce loading and cable losses that can alter amplitude and edge response, so each amplifier should use the manufacturer's documented source and termination arrangements. Keep branches short where possible, maintain return paths with a ground plane, and test reflections and overshoot at the connector with representative cable lengths before production use.
সুপারিশকৃত
সুপারিশকৃত পণ্যের সারসংক্ষেপ
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা LM2202MX — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য |
|---|---|
| Package | 20-SOIC |
| Brand | Texas Instruments |
| Product Type | Video amplifier system |
| Number of Circuits | 1 circuit |
| -3 dB Bandwidth | 230 MHz |
| Supply Current | 48 mA |
| Device Classification | Standard general purpose |
| Primary Application | High-resolution monochrome and RGB color monitors |
| Mounting Type | Surface mount |
| Product Status | Obsolete |
মূল পার্থক্যসমূহ
- Wide confirmed bandwidth for legacy analog video (বনামLM2202N)
- Single-channel general-purpose video amplification (বনামLM2202N)
- Direct fit for an existing 20-SOIC monitor-board footprint (বনামLM2202N)
ডিজাইন নোট
Route the video path as a controlled, short trace over a continuous ground reference. The confirmed 230 MHz bandwidth makes trace geometry, return-path continuity, and nearby clock or converter switching nodes more important than they would be for a low-frequency amplifier. Keep the input and output loops compact, avoid vias in sensitive video nets when practical, and maintain the manufacturer's recommended separation from digital and switching circuitry to reduce ringing and coupling.
Reproduce the manufacturer application circuit without substituting undocumented termination or gain values. Place the associated resistors, capacitors, and any input or output bias networks close to the device pins to minimize parasitic inductance and capacitance. Unused amplifier inputs must follow the datasheet's prescribed bias or termination arrangement rather than being left floating. Confirm the 20-SOIC footprint dimensions against the manufacturer drawing before releasing copper artwork.
Validate the complete video channel with the intended source impedance, cable, connector, and output load. A nominal 230 MHz -3 dB bandwidth does not by itself guarantee acceptable pulse fidelity in every installation, especially when rise times are much shorter than the reciprocal of the stated bandwidth. Check amplitude, edge rate, overshoot, ringing, and channel-to-channel skew at the connector, and adjust only after confirming that the circuit still follows the manufacturer's electrical limits.
কমপ্লায়েন্স তথ্য
No explicit environmental, lead-free, halogen-free, conflict-minerals, or automotive qualification statements were identified in the available manufacturer-related records.