LM239PW - Quad Open-Collector Comparator, 14-TSSOP | Texas Instruments
MPN: LM239PW ✓ সক্রিয়LM239PW সারাংশ
A voltage comparator is an analog integrated circuit that compares two input voltages and produces a logic-level indication of their relationship. The LM239 belongs to the comparator hierarchy, within analog interface and signal-conditioning semiconductors. Unlike a general-purpose operational amplifier used for closed-loop amplification, each comparator channel primarily switches its output according to the polarity of its differential input. Its open-collector architecture makes it useful for level translation, open-drain buses, and systems that require multiple devices to share a pull-up network.
The LM239PW provides four independent channels, a low typical input offset voltage of 0.37 mV, a typical input bias current of 3.5 nA, and a typical supply current of 200 µA per comparator. Its differential input range extends to ±38 V, while the common-mode input range includes ground. Open-collector outputs are compatible with TTL, MOS, and CMOS interfacing when suitable pull-up resistors are installed, and the low output saturation voltage supports reliable digital load drive.
Each channel operates independently, allowing the same package to perform four unrelated sensing or thresholding functions. The wide common-mode range is particularly useful in single-supply systems where one input remains near 0 V. The low offset and bias characteristics help establish thresholds with reduced input error, while the low typical supply current per channel supports low-power monitoring systems. Split-supply operation is also possible when the total supply span and input common-mode limits are respected.
Typical uses include industrial sensor interfaces, battery monitoring, overvoltage and undervoltage detection, window comparators, motor-control feedback, and general logic-level sensing. Because the outputs are open collector, pull-up resistors are required for normal high-level operation. A pull-up value should be selected from the required rise time, bus capacitance, sink-current limit, and downstream input characteristics rather than from the nominal supply voltage alone.
Designers should keep input leads short, place bypass capacitance close to the supply pins, and verify that every differential and common-mode input remains inside its rated range. Output collectors must not exceed their voltage and current limits, and unused comparator channels should be brought to defined legal states. This page combines application guidance, pin-level information, design checks, and verified same-footprint alternatives to support schematic capture and board-level replacement decisions.
এর জন্য ড্রপ-ইন বিকল্প LM239PW — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
এই সিরিজের ভ্যারিয়েন্ট
একই সিরিজের মডেল যেগুলো drop-in compatible LM239PW (একই form factor এবং footprint) — পার্থক্য রয়েছে Input Bias Current, Input Offset Voltage, Logic Compatibility, Package, Supply Current.
LM239PWG4
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
LM239PWE4
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
LM239PW সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য
| Comparator Type | Quad differential comparator |
| Number of Channels | 4 channels |
| Supply Voltage Range | 2 V to 36 V |
| Maximum Supply Voltage | 36 V |
| Differential Input Voltage Range | -38 V to +38 V |
| Common-Mode Input Range | Includes ground |
| Input Offset Voltage | 0.37 mV typical |
| Input Bias Current | 3.5 nA typical |
| সাপ্লাই কারেন্ট | 200 µA typical per comparator |
| আউটপুট টাইপ | Open-collector |
| Logic Compatibility | Compatible with TTL, MOS, and CMOS |
| প্যাকেজ | 14-pin TSSOP |
| মাউন্টিং টাইপ | Surface mount |
| Grade | Commercial |
| ESD Rating | 2 kV HBM |
| RoHS স্ট্যাটাস | Compliant |
| REACH Status | Compliant |
LM239PW পিন কনফিগারেশন
| পিন 1 | OUT1 — Comparator 1 open-collector output |
| পিন 2 | IN1- — Comparator 1 inverting input |
| পিন 3 | IN1+ — Comparator 1 non-inverting input |
| পিন 4 | GND — Ground |
| পিন 5 | IN2+ — Comparator 2 non-inverting input |
| পিন 6 | IN2- — Comparator 2 inverting input |
| পিন 7 | OUT2 — Comparator 2 open-collector output |
| পিন 8 | OUT3 — Comparator 3 open-collector output |
| পিন 9 | IN3- — Comparator 3 inverting input |
| পিন 10 | IN3+ — Comparator 3 non-inverting input |
| পিন 11 | GND — Ground |
| পিন 12 | IN4+ — Comparator 4 non-inverting input |
| পিন 13 | IN4- — Comparator 4 inverting input |
| পিন 14 | OUT4 — Comparator 4 open-collector output |
সাধারণ ব্যবহার
LM239PW এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Industrial Sensor Threshold Detection, Battery Voltage Monitoring, Power-Supply Rail Supervision, Motor and Actuator Feedback, Window Comparator and Control Systems, Automotive and Mobile Equipment Interlocks.
Industrial Sensor Threshold Detection
The LM239PW fits industrial sensor interfaces that need to compare a conditioned analog signal against a reference. Its four independent channels can monitor temperature, pressure, level, or proximity signals without requiring four separate packages, while the common-mode input range including ground supports sensors operating near 0 V. The 0.37 mV typical input offset and 3.5 nA typical input bias current reduce input-referred threshold errors when compared with a low-impedance reference. Each channel's open-collector output can drive a PLC input, relay-driver stage, or digital isolator through a suitable pull-up resistor. In industrial systems, select resistor values and protection components so switching transients and sensor faults cannot exceed the comparator's absolute-maximum ratings.
সুপারিশকৃত
Battery Voltage Monitoring
The LM239PW can implement threshold detection for multi-cell batteries, charger systems, and portable equipment. Its differential input capability of ±38 V provides useful headroom for divided battery voltages, while the common-mode range includes ground supports low-cell monitoring near the bottom of the discharge curve. Four channels can supervise different voltage bands or provide redundant comparisons. Open-collector outputs allow warning and shutdown signals to share wired buses when appropriate pull-up resistors are fitted. In a real battery design, use precision resistors, verify resistor power dissipation during worst-case charging, and add transient protection for hot-plug, load dump, and inductive events rather than assuming the ±38 V differential limit covers unprotected surges.
সুপারিশকৃত
Power-Supply Rail Supervision
The LM239PW is appropriate for detecting overvoltage, undervoltage, and window conditions in distributed power systems. The 2 V to 36 V operating range supports both low-voltage digital rails and higher industrial supply buses, while four channels permit independent supervision tasks. The ground-inclusive common-mode range is useful when monitoring a rail relative to its return. Open-collector outputs can trigger a system fault line, inhibit a regulator, or drive an isolation stage through pull-up resistors. For dependable supervision, verify the actual output saturation at the selected sink current, allow adequate pull-up rise time for the receiving circuit, and design divider ratios so normal tolerance, ripple, and transient excursions remain within the comparator's input limits.
সুপারিশকৃত
Motor and Actuator Feedback
The LM239PW can compare motor-position, current-sense, or actuator feedback signals against limit thresholds in industrial and embedded motion systems. Four independent channels make it practical to monitor positive and negative limits, fault flags, or redundant sensor conditions in a compact 14-pin TSSOP. The low typical supply current of 200 µA per comparator reduces the penalty when the monitoring circuit remains active. Its open-collector outputs can pull up alarm, shutdown, or direction-control signals without tying the device directly to a high-current motor driver. Keep sensing traces away from motor-switching nodes, use filtering where sensor ripple could cause chatter, and account for comparator response time when setting debounce or filtering around fast feedback events.
সুপারিশকৃত
Window Comparator and Control Systems
The LM239PW can implement window comparison by using two channels to detect lower and upper limits around a reference. This arrangement is useful in signal-range validation, automatic-range measurement, supply sequencing, and equipment protection. Its differential input range of ±38 V and common-mode range including ground allow the comparator to work with low-level control signals while remaining tolerant of larger differential excursions within the stated ratings. Open-collector outputs make it straightforward to combine an upper-limit and lower-limit indication into a common wired fault bus. Define hysteresis externally so noise around a threshold does not cause repeated output transitions, and verify that resistor tolerances do not unintentionally narrow the intended detection window.
সুপারিশকৃত
Automotive and Mobile Equipment Interlocks
The LM239PW can support interlock and presence-detection functions in mobile equipment and automotive-style control modules where the PCB area is constrained. Four channels in a 14-pin TSSOP provide multiple comparisons in one package, and the 36 V maximum supply rating is useful for systems with protected higher-voltage rails. The open-collector output can signal an interlock controller or drive an external relay driver when the required sink current and isolation are respected. Vehicle environments also require careful transient suppression, grounding, and temperature verification. Use the exact suffix-specific grade for the final product environment, include input clamps where conducted disturbances are possible, and avoid relying on a comparison result before the protection network has settled.
সুপারিশকৃত
সুপারিশকৃত পণ্যের সারসংক্ষেপ
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা LM239PW — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | LM239PWG4 | LM239PWE4 |
|---|---|---|---|
| Package | 14-pin TSSOP | 14-pin TSSOP | 14-pin TSSOP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Comparator Type | Quad differential comparator | Quad differential comparator | Quad differential comparator |
| Number of Channels | 4 channels | 4 channels | 4 channels |
মূল পার্থক্যসমূহ
- Four independent channels in one compact package (বনামLM239PWG4)
- Ground-inclusive common-mode input range (বনামLM239PWE4)
- Low input error for threshold detection (বনামLM239PWG4)
ডিজাইন নোট
Do not operate the open-collector outputs without pull-up resistors. The transistor can pull the output low but cannot actively drive it high. Select the pull-up voltage to match the receiving logic, confirm the maximum collector sink current at the required logic-low current, and use a resistance large enough to limit sink current while small enough to achieve the required bus rise time.
The typical supply current is 200 µA per comparator, but total current and dissipation rise with four active channels and output loading. Place the supply bypass capacitor close to the supply and ground pins, minimize trace resistance, and avoid routing output-transition currents through sensitive input-reference paths. Check the total supply current across the operating temperature range when the device remains continuously enabled.
Keep the four comparator input nets away from switching nodes, relay contacts, high-current outputs, and the open-collector traces that carry fast collector transitions. Connect the two ground pins to a low-impedance ground plane according to the datasheet layout guidance. For sensitive threshold measurements, use short traces, a stable reference source, and input filtering that preserves the required response time.
The differential input limit of ±38 V is not a general-purpose surge withstand rating. Do not connect the inputs directly to unclamped motor, battery, or mains-derived signals. Use resistive attenuation and suitable clamp protection, and verify that the complete input network preserves accuracy at the threshold while keeping the comparator pins within their absolute-maximum limits under normal and fault conditions.
কমপ্লায়েন্স তথ্য
RoHS and REACH compliance are identified in the LM239 ordering information. Automotive qualification, lead-free status, halogen-free status, and conflict-minerals status are not established for this specific ordering suffix.