STMicroelectronics

LM258WYDT - Dual 1.1MHz Operational Amplifier | STMicroelectronics

MPN: LM258WYDT ✓ সক্রিয়
Single supply or split supply Vdss 8-SOIC Package
সর্বনিম্ন অর্ডার পরিমাণ: 1 |

LM258WYDT সারাংশ

The STMicroelectronics LM258WYDT is a dual general-purpose operational amplifier with two amplifier circuits, a gain-bandwidth product of 1.1 MHz, and an 8-SOIC package. It is designed for instrumentation, signal-conditioning, industrial-control, and automation applications requiring two amplifiers in one package. The -W option provides the extended industrial temperature range, while the Y suffix identifies the SOIC package and T identifies tape-and-reel packing.

An operational amplifier, or op amp, is an active semiconductor device that amplifies the voltage difference between its two input terminals. Its high open-loop gain, high input impedance, and low output impedance make it useful in amplifier, buffer, comparator, summing, filtering, and current-control circuits. The dual LM258 family combines two independent amplifiers in one package, reducing component count and simplifying PCB layout.

The LM258WYDT provides two amplifier circuits in an 8-SOIC package and operates at a gain-bandwidth product of 1.1 MHz. Its general-purpose design is suitable for low-frequency instrumentation and industrial signal paths rather than high-speed precision applications. The extended-temperature -W grade is intended for environments beyond the standard commercial temperature range, subject to the operating limits in the STMicroelectronics datasheet.

The LM258 architecture supports operation from a single supply or split supplies, allowing its input and output signals to be referenced near ground when lower supply voltages are required. Because the two amplifiers share one package, careful decoupling and grounding remain important: each supply rail should have local bypass capacitance, and the common ground path should minimize voltage-drop-induced errors.

Typical uses include process-control loops, sensor conditioning, current monitoring, audio and communications interfaces, industrial data acquisition, and general-purpose analog signal conditioning. Each channel can be used independently as an inverting or non-inverting amplifier, voltage follower, comparator, or active-filter building block, provided the input, output, and common-mode ranges remain inside the datasheet limits.

When laying out the circuit, place the supply bypass capacitors close to the package power pins and route sensitive input and feedback connections away from switching nodes and high-current returns. Check output swing, input common-mode range, stability, and output-current requirements against the actual supply voltage and load before releasing the design.

This product summary combines the LM258WYDT device identity, package information, application guidance, and verified drop-in alternatives with practical design considerations for engineers evaluating an 8-SOIC dual op amp.

এর জন্য ড্রপ-ইন বিকল্প LM258WYDT — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।

LM258DR2G

✅ ড্রপ-ইন
onsemi
📦 8-SOIC
2 channels · 3 V to 32 V · 0.6 V/µs · -25°C to +85°C · 0.7 mA · 2 mV · 2 nA · 15 nA

মূল্যের জন্য যোগাযোগ করুন

ডেটাশিট দেখুন →

LM358ADT

✅ ড্রপ-ইন
📦 8-SOIC
Remains a 2-circuit device in an 8-SOIC package with 0% channel-count difference; channel-level offset, bias, common-mode, and temperature ratings require comparison

📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)

TSH22IDT

✅ ড্রপ-ইন
📦 8-SOIC
Provides the same 2-channel, 8-SOIC configuration with 0% channel-count or pin-count difference; performance ratings require verification against the original circuit

📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)

TSB7192IDT

✅ ড্রপ-ইন
📦 8-SOIC
Provides the same 2-channel, 8-SOIC configuration with 0% channel-count or pin-count difference; offset, bandwidth, common-mode, and temperature ratings require verification

📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)

LM258WYDT সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য

Product Type Dual general-purpose operational amplifier
Amplifier Circuit Count 2 circuits
Gain-Bandwidth Product 1.1 MHz
প্যাকেজ 8-SOIC
Total Pin Count 8 pins
মাউন্টিং টাইপ Surface mount
Packing Option T tape and reel
Temperature Grade -W extended industrial temperature grade
Supply Configuration Single supply or split supply

LM258WYDT 8-soic পিন কনফিগারেশন গাইড

LM258WYDT (8-soic প্যাকেজ)-এর পিন কনফিগারেশন। এই অ্যানালগ কম্পোনেন্টে ইনপুট, আউটপুট ও পাওয়ার সাপ্লাই পিন রয়েছে। অফসেট নাল, কম্পেনসেশন ও এনেবল পিন কনফিগারেশনের জন্য প্রস্তুতকারকের ডেটাশিট দেখুন। সিগন্যাল কন্ডিশনিং ও অ্যামপ্লিফায়ার সার্কিটের জন্য আদর্শ।

LM258WYDT-এর জন্য 8-soic প্যাকেজ পিনআউট ডায়াগ্রাম

এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি LM258WYDT.

দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।

সাধারণ ব্যবহার

LM258WYDT এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Industrial Sensor Signal Conditioning, Current Monitoring and Control Loops, Instrumentation and Data Acquisition, Audio and Communications Interfaces, Active Filtering and Signal Conditioning, Automation and Control Systems.

🏭

Industrial Sensor Signal Conditioning

The LM258WYDT fits two-stage industrial sensor conditioning because it combines two independent amplifiers with a 1.1 MHz gain-bandwidth product in one 8-SOIC package. One channel can amplify or level-shift a sensor output, while the second can buffer the result or form an active filter. Its general-purpose architecture supports moderate-bandwidth feedback networks and its -W grade targets extended industrial environments. The design must still verify that the sensor signal remains inside the input common-mode range and that the output does not exceed the available voltage swing.

⚡

Current Monitoring and Control Loops

The LM258WYDT is useful in current-monitoring and industrial control circuits that require gain, filtering, and buffering in a compact two-channel device. With a 1.1 MHz gain-bandwidth product, each channel can support moderate-frequency closed-loop operation and error-amplifier functions. A shunt amplifier can use one channel for amplification and the other for filtering or reference conditioning. Verify output-current capability, output swing, input bias current, and stability with the actual sensor and feedback values.

🖥️

Instrumentation and Data Acquisition

The two channels in the LM258WYDT can reduce analog-front-end complexity in instrumentation and data-acquisition systems. A typical arrangement uses one channel for gain and the second for active filtering or buffering before an ADC input. The 1.1 MHz gain-bandwidth product supports common low-to-moderate-bandwidth instrumentation signals, while the 8-SOIC package simplifies board layout. The engineer should check input offset, common-mode range, output swing, noise, and ADC drive requirements against the manufacturer datasheet.

🌐

Audio and Communications Interfaces

The LM258WYDT can implement low-frequency audio or communications interface functions where two general-purpose amplifier channels are needed without rail-to-rail performance. One channel may provide voltage gain while the other drives a coupling stage, buffers a control signal, or implements active filtering. Its 1.1 MHz gain-bandwidth product is appropriate for many baseband and control-signal paths. Check the output drive, load, slew rate, common-mode range, and allowable output distortion for the target signal level.

🔧

Active Filtering and Signal Conditioning

The LM258WYDT is appropriate for active-filter and general signal-conditioning stages that require two independent op amps and moderate closed-loop bandwidth. The 1.1 MHz gain-bandwidth product can support first- and second-order sections when component values and noise gain are selected appropriately. A single 8-SOIC package can implement a low-pass filter plus buffer, or a gain stage plus anti-alias filter. Validate noise gain, phase margin, component tolerances, output loading, and supply-voltage headroom in simulation and on the bench.

🏭

Automation and Control Systems

The LM258WYDT can support automation blocks that compare, amplify, or buffer low-frequency control signals. Its two channels allow a comparator function and a feedback amplifier to coexist in one package, reducing board area. The -W temperature grade is useful when ambient conditions extend beyond the standard commercial range. Ensure the chosen supply voltage supports the required input and output ranges, and review offset and bias-current errors when the controlled quantity requires high accuracy.

What is the LM258WYDT?
The LM258WYDT is a STMicroelectronics dual general-purpose operational amplifier with two independent amplifier circuits, a 1.1 MHz gain-bandwidth product, and an 8-SOIC package. According to the STMicroelectronics datasheet, the dual configuration supports single-supply or split-supply operation and is intended for general-purpose instrumentation and industrial signal-conditioning applications.
How many amplifiers are in the LM258WYDT package?
The LM258WYDT contains two independent operational-amplifier circuits in one 8-SOIC package. This arrangement allows the device to implement two analog functions, such as an instrumentation amplifier stage and a buffer, while reducing the number of packages and PCB connections. The STMicroelectronics datasheet provides the channel-level pin assignments and electrical limits.
What is the gain-bandwidth product of LM258WYDT?
The LM258WYDT has a gain-bandwidth product of 1.1 MHz. According to the manufacturer datasheet, this bandwidth makes it suitable for general-purpose low-frequency signal conditioning rather than high-speed video or precision wide-band instrumentation. Actual closed-loop bandwidth also depends on the selected noise gain, feedback network, load, and operating conditions.
Where can I download the LM258WYDT datasheet PDF?
The official STMicroelectronics LM258 datasheet is available from the manufacturer's product-document link on this page. It is the primary reference for the pin configuration, electrical characteristics, typical application circuits, and package information. Use the STMicroelectronics document rather than relying solely on a distributor summary when assigning PCB pins or checking operating limits.
Where can I find the LM258WYDT pinout?
The LM258WYDT pinout is shown in the manufacturer datasheet, where the two amplifier channels, supply pins, and ground connections are identified for the 8-SOIC package. Use that pin-description table when assigning PCB tracks. The package has eight pins, and correct orientation is essential because several pins have dedicated power or ground functions.
Can the LM258WYDT operate from a single supply?
Yes, the LM258WYDT can operate from a single supply or split supplies. According to the STMicroelectronics datasheet, single-supply operation is useful when the signal and output remain above the lower common-mode and output-swing limits. Check the required input common-mode range and output swing at the chosen supply voltage before finalizing the analog front end.
What is the difference between LM258WYDT and LM258DR2G?
Both devices are listed as 8-SOIC dual general-purpose operational amplifiers with approximately 1.1 MHz and 1.0 MHz gain-bandwidth products, respectively. The difference is approximately 0.1 MHz, or about 10%, for LM258WYDT relative to LM258DR2G. Confirm temperature grade, supply limits, offset parameters, and marking requirements before exchanging them.
LM258WYDT vs LM358ADT - which is better for instrumentation?
Choose LM258WYDT when a 1.1 MHz dual amplifier in the 8-SOIC format is the preferred fit, and choose LM358ADT when its channel-level electrical ratings better satisfy the design. Both are dual general-purpose op amps, but offset, bias-current, common-mode, output-swing, and temperature-range differences determine suitability. Compare the manufacturer datasheets for the exact operating conditions.
When should I choose LM258WYDT over another 8-SOIC dual op amp?
Choose LM258WYDT when the design requires two independent general-purpose amplifier channels, a 1.1 MHz gain-bandwidth product, and the extended -W temperature grade in an 8-SOIC package. Select another dual op amp when it offers lower offset voltage, rail-to-rail input or output, faster slew rate, lower noise, or a qualification status required by the application.
Is LM258WYDT suitable for sensor conditioning and industrial control?
The LM258WYDT is suitable for many sensor-conditioning and industrial-control loops requiring two low-frequency general-purpose amplifier channels. Its 1.1 MHz gain-bandwidth product supports moderate-bandwidth feedback networks, while the -W grade targets extended industrial conditions. Validate the sensor output range, common-mode limits, output swing, noise requirements, and grounding arrangement.
What is the best drop-in replacement for LM258WYDT?
LM258DR2G is the closest documented drop-in candidate because it is also a dual general-purpose op amp in an 8-SOIC package with a 1.0 MHz bandwidth versus 1.1 MHz for LM258WYDT. No other substitute should be treated as automatic without checking the pinout, temperature grade, common-mode range, output swing, offset voltage, and automotive or industrial qualification requirements.
Can LM358ADT replace LM258WYDT?
LM358ADT may serve as an 8-SOIC dual-op-amp alternative, but it is not automatically a drop-in replacement for every LM258WYDT circuit. Both devices provide two amplifier channels in the same general package format, yet their offset voltage, bias current, common-mode range, output swing, temperature range, and load behavior must be compared. Verify the pin-level schematic before substitution.
What can replace LM258WYDT?
Possible replacements include LM258DR2G, LM358ADT, TSH22IDT, and TSB7192IDT when each candidate's 8-SOIC dual-amplifier pinout and electrical ratings match the original circuit. The documented bandwidth difference for LM258DR2G is only 0.1 MHz, or about 10% relative to LM258WYDT. Final qualification must cover supply range, common-mode operation, output swing, stability, temperature grade, and qualification requirements.
What are the key specifications of LM258WYDT that engineers should know?
The key LM258WYDT specifications are two independent amplifier circuits, a 1.1 MHz gain-bandwidth product, and an 8-SOIC surface-mount package. The device is a general-purpose operational amplifier with an extended -W industrial temperature grade and tape-and-reel ordering suffix. Design checks should also cover input common-mode range, output swing, offset voltage, bias current, slew rate, and output-current capability.
Is LM258WYDT in stock and what is its lead time?
The LM258WYDT is shown as an orderable active part in current product listings, but current stock and lead time can change by region and order quantity. Use the Request a Quote form on this page for the exact package suffix, quantity, delivery date, and commercial terms. Do not substitute an automotive-qualified or differently packed ordering code without confirming the resulting marking and qualification.
How much does LM258WYDT cost?
The current unit price for LM258WYDT should be requested through the Request a Quote form on this page because pricing changes with quantity, sourcing date, and package suffix. Submit the exact MPN, required quantity, and shipment destination to obtain current commercial terms. The manufacturer part number identifies a 2-circuit, 1.1 MHz dual op amp in an 8-SOIC package.
Where can I buy LM258WYDT online?
Use the Request a Quote form on this page to purchase LM258WYDT with the exact 8-SOIC tape-and-reel ordering suffix. Provide the required quantity, shipment country, and target date so the order can be matched to current component availability. Confirm that the quotation specifies LM258WYDT rather than LM258DR2G, LM358ADT, or another pin-compatible dual-op-amp alternative.

এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা LM258WYDT — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।

নির্বাচন গাইড

Choose LM258WYDT for compact, general-purpose dual-op-amp designs that require an 8-SOIC package, a 1.1 MHz gain-bandwidth product, and an extended -W industrial temperature option. LM258DR2G is the closest bandwidth-matched option and may be suitable where the approximately 10% lower bandwidth does not affect the signal path. LM358ADT should be selected only after comparing offset, bias current, common-mode range, output swing, and temperature limits. TSH22IDT and TSB7192IDT are also 8-SOIC dual-amplifier candidates, but their channel-level characteristics require direct comparison with the original schematic. For designs requiring rail-to-rail inputs, very low offset, high output current, or low noise, select a newer precision or rail-to-rail amplifier instead and complete a full footprint and performance review.

বিকল্পের সাথে তুলনা

পারামিটার এই পণ্য LM258DR2G LM358ADT TSH22IDT TSB7192IDT
Brand STMicroelectronics STMicroelectronics STMicroelectronics STMicroelectronics STMicroelectronics
Package 8-SOIC 8-SOIC - same 8-SOIC - same 8-SOIC - same 8-SOIC - same
Amplifier Circuit Count 2 circuits 2 circuits 2 circuits 2 circuits 2 circuits
Total Pin Count 8 pins 8 pins 8 pins 8 pins 8 pins
Product Classification General-purpose operational amplifier General-purpose operational amplifier General-purpose operational amplifier Dual operational amplifier Dual operational amplifier

মূল পার্থক্যসমূহ

  • Higher documented bandwidth than LM258DR2G (বনামLM258DR2G)
  • Two channels in a compact 8-SOIC package (বনামLM324ADR)
  • Extended industrial temperature option (বনামLM358ADT)

ডিজাইন নোট

Place the supply bypass capacitors immediately adjacent to the LM258WYDT power and ground pins. Keep the loop formed by the capacitor, package power pin, package ground pin, and ground plane physically small. This reduces supply-impedance feedback and helps the two amplifier channels maintain predictable operation when both are active.

Route each non-inverting input directly to its source and keep each inverting-input feedback trace short and away from switching nodes. Because both channels share the package and ground reference, a common return-current path can couple noise from one channel into the other. Use a quiet ground region for sensitive inputs and provide a separate return path for output loads.

Do not assume that two channels in one package are automatically independent at every frequency. Internal power and ground connections can couple disturbances between channels, and output loads can create return-current transients. Verify output-current capability, capacitive-load stability, common-mode range, output swing, and supply headroom for the worst operating condition in the manufacturer datasheet.

Check closed-loop stability using the actual noise gain and load rather than relying only on the 1.1 MHz gain-bandwidth-product figure. For filtering or sensing applications, calculate the gain profile across the signal band and add suitable compensation for high-capacitance loads. Use the manufacturer test conditions as the basis for comparisons with alternative devices.

কমপ্লায়েন্স তথ্য

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
লিড ফ্রি
Unknown
হ্যালোজেন ফ্রি
Unknown
কনফ্লিক্ট মিনারেলস
Unknown

The product listing references RoHS and AEC-Q100, but it does not provide an explicit compliance or qualification declaration. Confirm the current declarations and ordering-code qualification status with STMicroelectronics before use in regulated production.

ডেটা যাচাই করা হয়েছে: 2026-11-15 — ডেটা XAIPART-এর কম্পোনেন্ট ইঞ্জিনিয়ারিং টিম দ্বারা যাচাই ও কিউরেট করা হয়েছে

সম্পর্কিত অনুসন্ধান

LM258WYDT LM258WYDT datasheet LM258WYDT datasheet pdf LM258WYDT pinout LM258WYDT 8-SOIC LM258WYDT 1.1MHz STMicroelectronics LM258WYDT LM258WYDT equivalent LM258WYDT replacement LM258WYDT vs LM258DR2G LM258WYDT price LM258WYDT stock LM258WYDT dual op amp LM258WYDT sensor signal conditioning LM258WYDT industrial control amplifier

সম্পর্কিত কম্পোনেন্ট ও শর্তাবলী

STMicroelectronics LM258WYDT LM258DR2G LM358ADT TSH22IDT TSB7192IDT LM2904PWR LM324ADR INA240A3DR dual operational amplifier general-purpose op amp operational amplifier analog signal conditioning gain-bandwidth product 1.1 MHz 8-SOIC SOIC package family surface-mount package single-supply operation split-supply operation input common-mode range output swing voltage active filter instrumentation amplifier industrial automation
তাৎক্ষণিক বিলওয়াছে রেকোজিউইট
সম্পূর্ণ বিবরণ পূরণ করুন — আমাদের সেলস টিম 24 ঘণ্টার মধ্যে উত্তর দেবে
পার্ট নম্বর উৎপাদক প্যাকেজ QTY লক্ষ্যমূল্য প্রসারিত
✓
বিল প্রস্তুত করা হয়েছে!

আমরা ২৪ ঘণ্টার মধ্যে আপনার ইমেইলে প্রত্যুত্তর দেব

1
RFQ জমা হয়েছে
2
কোটেশন পাওয়া গেছে
3
অর্ডার দেওয়া হয়েছে
4
পেমেন্ট
5
শিপ করা হয়েছে
6
ডেলিভারি হয়েছে
RFQ বিবরণ দেখুন