LM2902AMX - Quad 14-SOP Op Amp | onsemi | Signal Control
MPN: LM2902AMX ✓ সক্রিয়LM2902AMX সারাংশ
An operational amplifier is an analog amplifier that uses very high open-loop gain and negative feedback to amplify small voltage differences. The quad LM2902AMX places four amplifiers in one package, each with its own two inputs and one output while sharing the supply pins. Within the product taxonomy, it is an operational amplifier within the broader amplifier IC and analog signal-processing categories.
The LM2902AMX is specifically identified as a standard general-purpose amplifier, which makes it appropriate for buffering, current-to-voltage conversion, differential amplification, level shifting, and feedback-control circuits. Its 40 nA input bias current supports applications in which bias-related error must remain controlled around sensitive analog nodes. The 14-SOP package also provides a conventional surface-mount option for industrial, instrumentation, and embedded control equipment.
Because four amplifier sections share one package, the device can reduce component count and simplify routing in multi-channel analog boards. Typical uses include amplifier banks in control panels, sensor conditioning channels, active filtering, and low-frequency analog signal processing. Designers should confirm input common-mode range, output swing, supply-voltage limits, offset voltage, input offset current, unity-gain bandwidth, slew rate, noise, and temperature limits against the manufacturer datasheet before finalizing a design.
The principal design trade-off is that a general-purpose quad amplifier prioritizes flexibility and channel density rather than the very low offset, low noise, high bandwidth, or rail-to-rail performance available from specialized amplifier families. Applications operating from a single supply, near the positive rail, or with very small sensor signals may require additional output biasing or a different amplifier architecture. Decoupling capacitors, input protection, output loading, and stability with capacitive loads must also be evaluated per circuit.
This page combines package and catalog information with application guidance, drop-in replacement comparisons, and practical design notes. It is intended to help engineers qualify the LM2902AMX for industrial analog boards faster than by reading the datasheet and distributor listings separately.
এর জন্য ড্রপ-ইন বিকল্প LM2902AMX — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
এই সিরিজের ভ্যারিয়েন্ট
একই সিরিজের মডেল যেগুলো drop-in compatible LM2902AMX (একই form factor এবং footprint) — পার্থক্য রয়েছে Package.
LM2902M
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →LM2902AM
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
LM2902DR
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →LM2902DR
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →LM2902D
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →LM2902DT
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →LM2902AMX সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য
| Product Type | Quad operational amplifier |
| Amplifier Count | 4 circuits |
| প্যাকেজ | 14-SOP |
| Package Pin Count | 14 pins |
| মাউন্টিং টাইপ | Surface mount |
| Input Bias Current | 40 nA |
LM2902AMX পিন কনফিগারেশন
| পিন 1 | OUT1 — Amplifier 1 output |
| পিন 2 | IN1- — Amplifier 1 inverting input |
| পিন 3 | IN1+ — Amplifier 1 non-inverting input |
| পিন 4 | V+ — Positive supply connection |
| পিন 5 | IN2+ — Amplifier 2 non-inverting input |
| পিন 6 | IN2- — Amplifier 2 inverting input |
| পিন 7 | OUT2 — Amplifier 2 output |
| পিন 8 | OUT3 — Amplifier 3 output |
| পিন 9 | IN3- — Amplifier 3 inverting input |
| পিন 10 | IN3+ — Amplifier 3 non-inverting input |
| পিন 11 | V- — Negative supply connection |
| পিন 12 | IN4+ — Amplifier 4 non-inverting input |
| পিন 13 | IN4- — Amplifier 4 inverting input |
| পিন 14 | OUT4 — Amplifier 4 output |
সাধারণ ব্যবহার
LM2902AMX এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Industrial Sensor Signal Conditioning, Process Control Analog Front End, Measurement and Instrumentation Amplification, Active Filtering and Signal Conditioning, Power Supply Control and Feedback Loops, Embedded Control Analog Interface.
Industrial Sensor Signal Conditioning
The onsemi LM2902AMX suits four-channel industrial sensor conditioning when a general-purpose amplifier and the 14-SOP package are the principal requirements. Its listed 40 nA input bias current limits bias-induced error at higher-impedance sensor nodes, while four amplifier sections allow simultaneous conditioning of thermocouple, resistive-sensor, or low-level process signals. Each amplifier can buffer a source or amplify a differential bridge output. Before layout release, verify the input common-mode range against the sensor excitation level and confirm that amplifier offset, bandwidth, and output swing meet the required measurement accuracy.
সুপারিশকৃত
Process Control Analog Front End
The LM2902AMX can implement gain, buffering, and active filtering stages in a process-control analog front end. Four integrated amplifier sections reduce the number of packages needed for four similar channels and keep routing within one 14-SOP footprint. The 40 nA input bias current is useful when the source resistance is high, but the complete resistance and signal-amplitude budget must be calculated to determine the resulting input-referred error. Confirm the amplifier's common-mode range and output capability against the 4-20 mA or voltage-sensing stage being designed.
সুপারিশকৃত
Measurement and Instrumentation Amplification
The LM2902AMX is applicable to instrumentation front ends that need several buffered measurement channels within a compact surface-mount footprint. Four general-purpose amplifier sections can form non-inverting, inverting, difference, or active-filter stages, subject to the device's input and output voltage limits. The 40 nA input bias current contributes to error proportional to input impedance, so high-impedance transducers should be checked against the maximum bias current specified for the exact grade. Gain-bandwidth requirements and capacitive loading should also be verified before finalizing each channel.
সুপারিশকৃত
Active Filtering and Signal Conditioning
The LM2902AMX's four amplifier sections can implement first- and higher-order active filters, integrators, and gain stages where general-purpose performance is adequate. Integrating four amplifiers in one 14-SOP package simplifies multi-channel filter layouts and can reduce board-level component count. Filter stability still depends on the selected closed-loop gain, component tolerances, source impedance, and output load, so use the manufacturer's recommended operating conditions. Confirm the unity-gain bandwidth and slew rate before selecting component values for the highest frequency of interest.
সুপারিশকৃত
Power Supply Control and Feedback Loops
The LM2902AMX can support error-amplifier, feedback, and supervisory-loop functions in linear power-control circuitry. Its four amplifier sections allow several feedback or monitoring channels to share a package, although the common-mode and output limits determine whether each amplifier can directly sense the power stage's operating point. Check the maximum supply voltage, input offset, output swing, and stability requirements against the control-loop node voltages. Keep sensitive feedback traces short and maintain the ground-current path recommended for the amplifier in the power-management layout.
সুপারিশকৃত
Embedded Control Analog Interface
The LM2902AMX is useful as a multi-channel analog interface between sensors or external equipment and an embedded controller. Four amplifiers can provide input buffering, differential-to-single-ended conversion, level conditioning, or output drive ahead of an ADC. The 40 nA input bias current is beneficial when source impedance is moderate, while the 14-SOP package supports compact board layouts. Verify the ADC input range, amplifier output swing, settling requirements, and channel-to-channel behavior. If the controller already incorporates programmable analog functions, confirm that the added amplifier channels provide a necessary accuracy or drive improvement.
সুপারিশকৃত
সুপারিশকৃত পণ্যের সারসংক্ষেপ
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা LM2902AMX — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | LM2902M | LM2902AM | LM2902DR | LM2902DR | LM2902D | LM2902DT |
|---|---|---|---|---|---|---|---|
| Brand | onsemi | onsemi | onsemi | onsemi | STMicroelectronics | NXP Semiconductors | STMicroelectronics |
| Package | 14-SOP (SOIC-14) | 14-SOP (SOIC-14) | 14-SOP (SOIC-14) | 14-SOP (SOIC-14) | 14-SOP (SOIC-14) | 14-SOP (SOIC-14) | 14-SOP (SOIC-14) |
| Amplifier Count | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits |
| Pin Count | 14 pins | 14 pins | 14 pins | 14 pins | 14 pins | 14 pins | 14 pins |
মূল পার্থক্যসমূহ
- Four-channel integration in a conventional 14-SOP package (বনামLM358N)
- Listed 40 nA input bias current (বনামLM2902M)
- Same-family drop-in option for onsemi boards (বনামSTMicroelectronics LM2902DR)
- Cross-brand sourcing flexibility with a common 14-pin architecture (বনামNXP LM2902D)
ডিজাইন নোট
Keep the four amplifier channels' input and feedback traces short and route them away from switching nodes, high-current power paths, and digital clock signals. Place supply-bypass capacitors close to the V+ and V- pins with short ground returns. Because all four amplifiers share package supply connections, high-current output loading on one section can create package-level supply disturbance across the other sections; split return paths or add local decoupling when channels operate at widely different load levels.
Do not assume that the LM2902 family reaches either supply rail. Check the input common-mode range and output voltage swing in the manufacturer datasheet against the minimum and maximum signal present at every amplifier pin, especially in single-supply designs. For a single-supply circuit operating near ground, either bias the signal within the usable input range or place a suitable offset-reference amplifier in front of the LM2902AMX. Also check the exact grade's maximum supply voltage.
Estimate input-referred bias error by multiplying the 40 nA listed input bias current by the total resistance seen at the relevant input. This error becomes significant for megohm-scale sensor networks even when the amplifier itself is stable. Use lower source impedance where practical, maintain balanced feedback impedances, and apply input-bias compensation when the application requires precision DC measurements. Verify offset voltage, input offset current, and drift for the exact LM2902 grade in addition to nominal bias current.
For capacitive sensor outputs, amplifier inputs, and feedback networks, use compact guard techniques and keep sensitive nodes physically separated from ground and supply-current paths. Avoid adding long point-to-point jumper wiring around the amplifier because parasitic capacitance can alter feedback behavior. If the load is capacitive, use the manufacturer's stability guidance, including an isolation resistor or compensation network, rather than driving a large capacitor directly from the output.
কমপ্লায়েন্স তথ্য
The LM2902AMX is a general-purpose operational amplifier; AEC-Q100 qualification does not apply. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not established by the available catalog records and remain unknown.