Texas Instruments

LM2902KDBRG4 - 26V Quad Op Amp | Texas Instruments

MPN: LM2902KDBRG4 ✓ সক্রিয়
3 V to 26 V Vdss 60 mA per channel Id 2 MΩ typical Rds(on) 14-SSOP, 0.209 inch body width (5.30 mm) Package
সর্বনিম্ন অর্ডার পরিমাণ: 1 |

LM2902KDBRG4 সারাংশ

The Texas Instruments LM2902KDBRG4 is a quad general-purpose operational amplifier designed for a 3 V to 26 V supply, with output current up to 60 mA per channel and a gain-bandwidth product of 1.2 MHz. The device is housed in a 14-pin SSOP package with an operating temperature range of -40°C to +125°C. Each amplifier provides a unity-gain bandwidth of 1.2 MHz, a slew rate of 0.5 V/μs and a typical open-loop gain of 50 dB.

An operational amplifier is an analog signal-conditioning IC that amplifies the voltage difference between its non-inverting and inverting inputs. The LM2902K belongs to the operational-amplifier hierarchy, which sits under analog amplifiers and integrated circuits. Its four independent channels make it practical where a design needs several comparators, buffers, transimpedance stages or low-frequency feedback amplifiers without using four separate packages.

The principal performance features include a 0.5 μA typical input bias current, 20 nA typical input offset current, a typical differential input resistance of 2 MΩ and a common-mode input range extending to approximately 0.5 V below the positive supply rail. The amplifier also supports rail-to-rail output swing under suitable load conditions, although its input common-mode range is not rail-to-rail.

The LM2902K architecture uses a classic general-purpose design with an internal bias stage and an output stage capable of sourcing or sinking 60 mA per channel. Its 1.2 MHz gain-bandwidth product is adequate for audio-frequency, sensor-conditioning, control-loop and general analog signal-processing tasks, but it is not intended for high-speed data acquisition or precision millivolt-level instrumentation.

Typical uses include four-channel sensor interfaces, low-cost audio mixing and filtering, industrial control signal conditioning, current-to-voltage conversion with external resistors, and comparator-style threshold detection. The wide 26 V maximum supply rating also supports 24 V industrial systems, provided signal amplitudes remain inside the input common-mode range and output current stays below the channel limit.

When laying out a circuit, place the bypass capacitor close to the positive supply pin, route the ground return directly to the ground pin, and keep sensitive input traces away from output and supply nodes. Decoupling resistance can create gain peaking near the 1.2 MHz crossover region, so feedback-network values should be selected with the amplifier's gain-bandwidth behavior in mind.

এর জন্য ড্রপ-ইন বিকল্প LM2902KDBRG4 — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।

LM2902KDBR

✅ ড্রপ-ইন
Texas Instruments
📦 14-SSOP
4 channels · General-purpose operational amplifier · 26 V · 1.2 MHz · 2 kV improved ESD · 3 mV · 2 nA · 0.8 mA

মূল্যের জন্য যোগাযোগ করুন

ডেটাশিট দেখুন →

LM2902KDBRG4 সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য

Amplifier Type General-purpose operational amplifier
Number of Channels 4 channels
Number of Amplifiers 4 amplifiers
Supply Voltage Range 3 V to 26 V
Maximum Supply Voltage 26 V
আউটপুট ভোল্টেজ রেঞ্জ -13 V to +13 V
Gain-Bandwidth Product 1.2 MHz
Slew Rate 0.5 V/μs
Open-Loop Gain 50 dB typical
Output Current 60 mA per channel
Input Bias Current 0.5 μA typical
Input Offset Current 20 nA typical
Differential Input Resistance 2 MΩ typical
Input Common-Mode Range Approximately 0.5 V below the positive supply rail
অপারেটিং তাপমাত্রার পরিসর -40°C to +125°C
ESD Rating 2 kV improved ESD
প্যাকেজ 14-SSOP, 0.209 inch body width (5.30 mm)
পিন সংখ্যা 14 pins
মাউন্টিং টাইপ Surface mount
Automotive Qualification AEC-Q100 qualified

LM2902KDBRG4 পিন কনফিগারেশন

SOIC-14 (3.9mm) Package Pinout Diagram SOIC-14 14-pin small outline IC, 3.9x8.7mm, P1.27mm, JEDEC MS-012. Pin 1 by chamfer. 1 14 2 13 3 12 4 11 5 10 6 9 7 8 SOIC-14 (3.9mm)
পিন 1 OUT1 — Channel 1 output
পিন 2 -IN1 — Channel 1 inverting input
পিন 3 +IN1 — Channel 1 non-inverting input
পিন 4 V- — Negative supply connection
পিন 5 +IN2 — Channel 2 non-inverting input
পিন 6 -IN2 — Channel 2 inverting input
পিন 7 OUT2 — Channel 2 output
পিন 8 OUT3 — Channel 3 output
পিন 9 -IN3 — Channel 3 inverting input
পিন 10 +IN3 — Channel 3 non-inverting input
পিন 11 V+ — Positive supply connection
পিন 12 +IN4 — Channel 4 non-inverting input
পিন 13 -IN4 — Channel 4 inverting input
পিন 14 OUT4 — Channel 4 output

সাধারণ ব্যবহার

LM2902KDBRG4 এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Industrial Sensor Signal Conditioning, Low-Cost Audio Mixing, Comparator and Threshold Detection, Current-to-Voltage Conversion, Power Feedback Control Loops, Communications Interface Buffering.

🏭

Industrial Sensor Signal Conditioning

The LM2902KDBRG4 is suitable for conditioning sensors that produce voltages well above the noise floor of a general-purpose amplifier. Its 1.2 MHz gain-bandwidth product handles slow sensor signals with ample bandwidth, while four channels can amplify, invert and buffer related inputs without adding extra packages. The 3 V to 26 V supply range accommodates 24 V industrial systems. A practical limitation is the input common-mode range, which approaches but does not include the positive supply rail, so bridge and current-sense nodes should be scaled appropriately.

🎧

Low-Cost Audio Mixing

Four independent LM2902KDBRG4 channels can implement four audio preamplifier, summing or mixing sections in a compact analog design. The 1.2 MHz gain-bandwidth product covers the audio band with substantially more bandwidth than required for many low-rate voice and control signals, and the 0.5 V/μs slew rate helps preserve moderate-amplitude waveforms. The 60 mA output capability supports headphone-buffer-like stages or small-signal drive, although a dedicated audio amplifier remains preferable for driving low-impedance loudspeakers.

📺

Comparator and Threshold Detection

The LM2902KDBRG4 can operate as an open-loop comparator for overvoltage, undervoltage or setpoint detection when the input signal stays within the common-mode range. Its 1.2 MHz unity-gain bandwidth and 0.5 V/μs slew rate provide faster response than the slow comparators used in many legacy control boards. Four channels allow monitoring several rails or thresholds on one board, but propagation delay and input overvoltage behavior should be checked in the datasheet before using it for fast protection loops.

🧩

Current-to-Voltage Conversion

A transimpedance amplifier built around one LM2902KDBRG4 channel converts a sensor current into a measurable voltage. The 2 MΩ typical differential input resistance and 0.5 μA typical input bias current are important when working with high-impedance sources. The 1.2 MHz bandwidth allows reasonably fast photodiode or optical-interface monitoring, while the four channels support dual-ended sensing or parallel photodiode channels. A dedicated transimpedance amplifier is preferable when very low capacitance, high speed or extreme precision is required.

⚡

Power Feedback Control Loops

The LM2902KDBRG4 can implement error amplifiers in linear power-supply feedback loops, with four channels providing control, filtering and auxiliary buffering functions. Its 26 V maximum supply supports 24 V industrial rails, and the 0.5 V/μs slew rate allows loop compensation with meaningful phase margin. Designers must account for the output current limit, saturation recovery and the input common-mode restriction. Dedicated regulators or dedicated error amplifiers generally provide tighter internal control for precision power conversion.

🌐

Communications Interface Buffering

The LM2902KDBRG4 provides four unity-gain or inverting buffers for low-speed communications, instrumentation and interface conditioning. The 1.2 MHz gain-bandwidth product is suitable for baseband signals, while the wide supply range permits operation from 5 V, 12 V or 24 V rails. Its improved 2 kV ESD rating adds robustness at exposed connector inputs when protection networks are also used. For higher data rates, differential channels or very low jitter, a dedicated interface amplifier is the better selection.

What is the operating voltage range of the LM2902KDBRG4?
The LM2902KDBRG4 operates from a single positive supply of 3 V to 26 V. According to the Texas Instruments LM2902K product page and datasheet, this wide range supports both conventional low-voltage analog systems and 24 V industrial equipment. Signal amplitudes must still remain inside the input common-mode range, which extends to approximately 0.5 V below the positive supply rail rather than to the negative rail.
Where can I download the LM2902KDBRG4 datasheet PDF?
The authoritative LM2902KDBRG4 documentation is available through the Texas Instruments LM2902K product page at https://www.ti.com/product/LM2902K. The datasheet describes the quad amplifier, electrical characteristics, pin configuration and typical applications. The same device also appears on the LM2902KDBRG4 distributor datasheet page, but the manufacturer-hosted document should be used as the primary reference for design decisions.
What is the gain-bandwidth product and slew rate of LM2902KDBRG4?
The LM2902KDBRG4 has a gain-bandwidth product of 1.2 MHz and a slew rate of 0.5 V/μs. According to the Texas Instruments LM2902K documentation, these ratings position the device as a general-purpose, low-frequency amplifier. It works well for audio, sensor buffering and control loops, while the 1.2 MHz bandwidth limits large-signal performance at higher frequencies.
What is the LM2902KDBRG4 pinout?
The 14-pin SSOP pinout assigns pins 1 through 7 to channel 1 and the first half of channel 2, while pins 8 through 14 complete channels 3 and 4 and the supply connections. Pin 1 is OUT1, pins 2 and 3 are -IN1 and +IN1, pin 4 is V−, pins 5 and 6 are +IN2 and -IN2, and pin 7 is OUT2. Use the pin-description table in the manufacturer datasheet when assigning PCB tracks.
Is the LM2902KDBRG4 a quad operational amplifier?
Yes, the LM2902KDBRG4 contains four independent general-purpose operational amplifiers in one 14-pin SSOP package. Texas Instruments describes the LM2902K as a quad 26 V, 1.2 MHz operational amplifier with improved 2 kV ESD protection. The four channels can be used simultaneously for separate buffers, amplifiers, comparators or transimpedance stages when their supply and grounding connections are shared.
How much output current can each LM2902KDBRG4 channel source?
Each LM2902KDBRG4 channel supports 60 mA of output current. The distributor component listing for this exact MPN identifies the value as 60 mA per channel. This rating applies to the amplifier output stage, not to the supply pins, and designers should leave margin for continuous DC loads, capacitive loading and temperature-dependent limits.
What can replace the LM2902KDBRG4 on the same PCB footprint?
The closest pin-compatible drop-in option is the LM2902KDBR, which uses the same 14-SSOP package and the same LM2902K electrical configuration. It differs primarily in ordering and packaging notation rather than in the amplifier function. Check the exact orderable part number, temperature grade and reel configuration before substituting it in a released design.
Is LM2902KDBRG4 the same as LM2902KDBR?
The LM2902KDBRG4 and LM2902KDBR refer to the same Texas Instruments LM2902K quad-amplifier configuration in a 14-SSOP package. The trailing characters identify the supplier packaging code. For an existing PCB, confirm that the alternative's lead dimensions, pin numbering and temperature rating match the assembled part rather than relying on the orderable code alone.
What is the best drop-in replacement for the LM2902KDBRG4?
The best same-footprint replacement identified for the LM2902KDBRG4 is the LM2902KDBR from Texas Instruments. It retains the 14-SSOP package, four-amplifier configuration, 3 V to 26 V supply range and 1.2 MHz bandwidth of the LM2902K family. A distributor cross-reference page also identifies LM2902DG, but its SOIC package is not pin-to-pin drop-in compatible with the SSOP footprint.
LM2902KDBRG4 vs LM2902DG - which one fits an existing SSOP board?
The LM2902KDBRG4 fits an existing 14-SSOP board because it is offered in that package, while the LM2902DG is identified as an SOIC alternative and requires a different footprint. Although both devices belong to the LM2902 family and provide four general-purpose amplifiers, a board change is necessary for the SOIC option. Confirm land patterns and pin orientation before considering any non-identical package.
When should I choose the LM2902KDBRG4 over a precision op amp?
Choose the LM2902KDBRG4 when cost, supply voltage and general-purpose performance matter more than microvolt offset accuracy or rail-to-rail input operation. Its 1.2 MHz bandwidth, 26 V supply rating and four integrated channels suit audio and industrial signal conditioning. For precision bridge sensing, low-offset measurement or signals near the supply rails, a dedicated precision amplifier is usually a better fit.
Is the LM2902KDBRG4 suitable for 24 V industrial control circuits?
The LM2902KDBRG4 is suitable for 24 V industrial control circuits because its recommended supply range extends to 26 V. The 60 mA per-channel output rating also covers many relay, monitor and low-power actuator interface loads. Keep transients below the maximum supply rating and protect inputs and outputs with suitable clamps when inductive loads are switched.
What are the key specifications of LM2902KDBRG4 that engineers should know?
The key LM2902KDBRG4 specifications are four channels in a 14-SSOP package, a 3 V to 26 V supply range, 1.2 MHz gain-bandwidth product, 0.5 V/μs slew rate, 60 mA output current per channel and an operating temperature range of -40°C to +125°C. Texas Instruments also specifies improved 2 kV ESD protection and AEC-Q100 qualification for automotive-oriented designs.
Where can I buy the LM2902KDBRG4 and check its price?
Use the Request a Quote form on this page to request LM2902KDBRG4 pricing, current stock and a committed lead time. The form allows you to specify the required quantity and packaging before placing an order. This route keeps the commercial terms tied to the exact 14-SSOP orderable part number and avoids ambiguity with other LM2902 package variants.
What is the lead time for LM2902KDBRG4?
The current lead time for LM2902KDBRG4 should be requested through the Request a Quote form on this page. Quote requests can reflect the specific quantity, scheduled delivery and any date-sensitive production requirements. The manufacturer identifies LM2902K as an active product, but a confirmed production lead time is required for each procurement event.
Is the LM2902KDBRG4 currently in stock?
Current LM2902KDBRG4 stock status should be confirmed through the Request a Quote form on this page. The form records the exact MPN and requested quantity so an availability response corresponds to the 14-SSOP configuration you intend to assemble. Inventory can change quickly, making a direct stock confirmation more reliable than a general distributor listing.
Does the LM2902KDBRG4 meet automotive and environmental compliance requirements?
The LM2902KDBRG4 is identified as AEC-Q100 qualified for automotive applications and includes improved ESD protection rated at 2 kV. According to the LM2902K family documentation, the device operates from -40°C to +125°C, supporting industrial and automotive temperature environments. Request the current material and compliance declarations through the Request a Quote form for the exact orderable part.

এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা LM2902KDBRG4 — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।

নির্বাচন গাইড

Choose the LM2902KDBRG4 for general-purpose analog designs that require four amplifiers, a supply voltage above 5 V and a footprint matching the 14-SSOP LM2902K family. It is a practical fit for industrial sensing, audio mixing, threshold detection and low-speed interface buffering. Select the LM2902KDBR when its specific orderable packaging code better matches procurement or assembly requirements, since it retains the same electrical architecture and package. Use a precision amplifier when offset voltage, bias current or input common-mode headroom dominates the design, and use a dedicated high-speed amplifier when the signal exceeds the 1.2 MHz bandwidth or the 0.5 V/μs slew rate. For a new board, verify land patterns, pin orientation and thermal performance against the manufacturer package drawing before committing the footprint.

বিকল্পের সাথে তুলনা

পারামিটার এই পণ্য LM2902KDBR
Brand Texas Instruments Texas Instruments
Package 14-SSOP 14-SSOP - same
Amplifier Configuration Quad general-purpose operational amplifier Quad general-purpose operational amplifier
Supply Voltage Range 3 V to 26 V 3 V to 26 V
Gain-Bandwidth Product 1.2 MHz 1.2 MHz
Slew Rate 0.5 V/μs 0.5 V/μs
Output Current 60 mA per channel 60 mA per channel
Input Bias Current 0.5 μA typical 0.5 μA typical
Input Offset Current 20 nA typical 20 nA typical
Operating Temperature Range -40°C to +125°C -40°C to +125°C

মূল পার্থক্যসমূহ

  • Four amplifiers in one 14-SSOP package (বনামLM2902KDBR)
  • Wide 26 V supply capability (বনামLM2902KDBR)
  • Improved ESD protection for exposed analog interfaces (বনামLM2902KDBR)

ডিজাইন নোট

Place the supply bypass capacitor close to pin 11, V+, and connect pin 4, V−, to a low-impedance ground plane. Route input and output traces away from the supply-capacitor return path to reduce injection of switching noise. Because four channels share the same supply pins, a local bypass arrangement supports all amplifiers but can also couple channel-to-channel disturbance through a common impedance.

Do not assume rail-to-rail input operation. The input common-mode range extends approximately 0.5 V below the positive rail, so signals that approach V+ may require attenuation, level shifting or a bias reference. Likewise, output current above 60 mA per channel is outside the device rating. Check the output saturation and common-mode limits in the manufacturer datasheet for the intended supply and load conditions.

Use feedback resistors that keep closed-loop gain well below the 1.2 MHz gain-bandwidth product and verify stability with the actual load capacitance. Very small feedback resistors may cause the amplifier to drive capacitive loads into oscillation. When four channels process related signals, keep sensitive inputs away from adjacent output pins and use separate return paths where channel-to-channel coupling would be critical.

কমপ্লায়েন্স তথ্য

RoHS
Unknown
REACH
Unknown
AEC-Q100
Qualified
লিড ফ্রি
Unknown
হ্যালোজেন ফ্রি
Unknown
কনফ্লিক্ট মিনারেলস
Unknown

The LM2902K family documentation identifies AEC-Q100 qualification for automotive applications and improved ESD protection. Current RoHS, REACH, lead-free, halogen-free and conflict-minerals declarations should be confirmed for the exact orderable MPN.

ডেটা যাচাই করা হয়েছে: 2026-11-09 — ডেটা XAIPART-এর কম্পোনেন্ট ইঞ্জিনিয়ারিং টিম দ্বারা যাচাই ও কিউরেট করা হয়েছে

সম্পর্কিত অনুসন্ধান

LM2902KDBRG4 datasheet LM2902KDBRG4 datasheet pdf LM2902KDBRG4 pinout Texas Instruments LM2902KDBRG4 LM2902KDBRG4 14-SSOP pinout LM2902KDBRG4 specifications LM2902KDBRG4 vs LM2902DG LM2902KDBRG4 drop-in replacement LM2902KDBRG4 equivalent LM2902KDBRG4 price LM2902KDBRG4 stock LM2902KDBRG4 application circuit LM2902KDBRG4 lead time what replaces LM2902KDBRG4 is LM2902KDBRG4 the same as LM2902KDBR

সম্পর্কিত কম্পোনেন্ট ও শর্তাবলী

Texas Instruments LM2902KDBRG4 LM2902K LM2902KDBR LM2902DG operational amplifier quad operational amplifier analog amplifier integrated circuit general-purpose amplifier gain-bandwidth product unity-gain bandwidth slew rate input bias current input offset current common-mode input range AEC-Q100 ESD protection 14-SSOP surface-mount package industrial sensor conditioning audio mixing transimpedance amplifier power-supply feedback control
তাৎক্ষণিক বিলওয়াছে রেকোজিউইট
সম্পূর্ণ বিবরণ পূরণ করুন — আমাদের সেলস টিম 24 ঘণ্টার মধ্যে উত্তর দেবে
পার্ট নম্বর উৎপাদক প্যাকেজ QTY লক্ষ্যমূল্য প্রসারিত
✓
বিল প্রস্তুত করা হয়েছে!

আমরা ২৪ ঘণ্টার মধ্যে আপনার ইমেইলে প্রত্যুত্তর দেব

1
RFQ জমা হয়েছে
2
কোটেশন পাওয়া গেছে
3
অর্ডার দেওয়া হয়েছে
4
পেমেন্ট
5
শিপ করা হয়েছে
6
ডেলিভারি হয়েছে
RFQ বিবরণ দেখুন