LM2902KDBRG4 - 26V Quad Op Amp | Texas Instruments
料号: LM2902KDBRG4 ✓ 量产中LM2902KDBRG4 概述
An operational amplifier is an analog signal-conditioning IC that amplifies the voltage difference between its non-inverting and inverting inputs. The LM2902K belongs to the operational-amplifier hierarchy, which sits under analog amplifiers and integrated circuits. Its four independent channels make it practical where a design needs several comparators, buffers, transimpedance stages or low-frequency feedback amplifiers without using four separate packages.
The principal performance features include a 0.5 μA typical input bias current, 20 nA typical input offset current, a typical differential input resistance of 2 MΩ and a common-mode input range extending to approximately 0.5 V below the positive supply rail. The amplifier also supports rail-to-rail output swing under suitable load conditions, although its input common-mode range is not rail-to-rail.
The LM2902K architecture uses a classic general-purpose design with an internal bias stage and an output stage capable of sourcing or sinking 60 mA per channel. Its 1.2 MHz gain-bandwidth product is adequate for audio-frequency, sensor-conditioning, control-loop and general analog signal-processing tasks, but it is not intended for high-speed data acquisition or precision millivolt-level instrumentation.
Typical uses include four-channel sensor interfaces, low-cost audio mixing and filtering, industrial control signal conditioning, current-to-voltage conversion with external resistors, and comparator-style threshold detection. The wide 26 V maximum supply rating also supports 24 V industrial systems, provided signal amplitudes remain inside the input common-mode range and output current stays below the channel limit.
When laying out a circuit, place the bypass capacitor close to the positive supply pin, route the ground return directly to the ground pin, and keep sensitive input traces away from output and supply nodes. Decoupling resistance can create gain peaking near the 1.2 MHz crossover region, so feedback-network values should be selected with the amplifier's gain-bandwidth behavior in mind.
直接替换替代料: LM2902KDBRG4 ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
LM2902KDBR
✅ 直接替换联系询价
查看数据手册 →LM2902KDBRG4 最大额定值与电气特性
| Amplifier Type | General-purpose operational amplifier |
| Number of Channels | 4 channels |
| Number of Amplifiers | 4 amplifiers |
| Supply Voltage Range | 3 V to 26 V |
| Maximum Supply Voltage | 26 V |
| 输出电压范围 | -13 V to +13 V |
| Gain-Bandwidth Product | 1.2 MHz |
| Slew Rate | 0.5 V/μs |
| Open-Loop Gain | 50 dB typical |
| Output Current | 60 mA per channel |
| Input Bias Current | 0.5 μA typical |
| Input Offset Current | 20 nA typical |
| Differential Input Resistance | 2 MΩ typical |
| Input Common-Mode Range | Approximately 0.5 V below the positive supply rail |
| 工作温度范围 | -40°C to +125°C |
| ESD Rating | 2 kV improved ESD |
| 封装 | 14-SSOP, 0.209 inch body width (5.30 mm) |
| 引脚数量 | 14 pins |
| 安装类型 | Surface mount |
| Automotive Qualification | AEC-Q100 qualified |
LM2902KDBRG4 引脚配置
| 引脚 1 | OUT1 — Channel 1 output |
| 引脚 2 | -IN1 — Channel 1 inverting input |
| 引脚 3 | +IN1 — Channel 1 non-inverting input |
| 引脚 4 | V- — Negative supply connection |
| 引脚 5 | +IN2 — Channel 2 non-inverting input |
| 引脚 6 | -IN2 — Channel 2 inverting input |
| 引脚 7 | OUT2 — Channel 2 output |
| 引脚 8 | OUT3 — Channel 3 output |
| 引脚 9 | -IN3 — Channel 3 inverting input |
| 引脚 10 | +IN3 — Channel 3 non-inverting input |
| 引脚 11 | V+ — Positive supply connection |
| 引脚 12 | +IN4 — Channel 4 non-inverting input |
| 引脚 13 | -IN4 — Channel 4 inverting input |
| 引脚 14 | OUT4 — Channel 4 output |
典型应用
LM2902KDBRG4 适用于 6 应用s: Industrial Sensor Signal Conditioning, Low-Cost Audio Mixing, Comparator and Threshold Detection, Current-to-Voltage Conversion, Power Feedback Control Loops, Communications Interface Buffering.
Industrial Sensor Signal Conditioning
The LM2902KDBRG4 is suitable for conditioning sensors that produce voltages well above the noise floor of a general-purpose amplifier. Its 1.2 MHz gain-bandwidth product handles slow sensor signals with ample bandwidth, while four channels can amplify, invert and buffer related inputs without adding extra packages. The 3 V to 26 V supply range accommodates 24 V industrial systems. A practical limitation is the input common-mode range, which approaches but does not include the positive supply rail, so bridge and current-sense nodes should be scaled appropriately.
推荐
Low-Cost Audio Mixing
Four independent LM2902KDBRG4 channels can implement four audio preamplifier, summing or mixing sections in a compact analog design. The 1.2 MHz gain-bandwidth product covers the audio band with substantially more bandwidth than required for many low-rate voice and control signals, and the 0.5 V/μs slew rate helps preserve moderate-amplitude waveforms. The 60 mA output capability supports headphone-buffer-like stages or small-signal drive, although a dedicated audio amplifier remains preferable for driving low-impedance loudspeakers.
推荐
Comparator and Threshold Detection
The LM2902KDBRG4 can operate as an open-loop comparator for overvoltage, undervoltage or setpoint detection when the input signal stays within the common-mode range. Its 1.2 MHz unity-gain bandwidth and 0.5 V/μs slew rate provide faster response than the slow comparators used in many legacy control boards. Four channels allow monitoring several rails or thresholds on one board, but propagation delay and input overvoltage behavior should be checked in the datasheet before using it for fast protection loops.
推荐
Current-to-Voltage Conversion
A transimpedance amplifier built around one LM2902KDBRG4 channel converts a sensor current into a measurable voltage. The 2 MΩ typical differential input resistance and 0.5 μA typical input bias current are important when working with high-impedance sources. The 1.2 MHz bandwidth allows reasonably fast photodiode or optical-interface monitoring, while the four channels support dual-ended sensing or parallel photodiode channels. A dedicated transimpedance amplifier is preferable when very low capacitance, high speed or extreme precision is required.
推荐
Power Feedback Control Loops
The LM2902KDBRG4 can implement error amplifiers in linear power-supply feedback loops, with four channels providing control, filtering and auxiliary buffering functions. Its 26 V maximum supply supports 24 V industrial rails, and the 0.5 V/μs slew rate allows loop compensation with meaningful phase margin. Designers must account for the output current limit, saturation recovery and the input common-mode restriction. Dedicated regulators or dedicated error amplifiers generally provide tighter internal control for precision power conversion.
推荐
Communications Interface Buffering
The LM2902KDBRG4 provides four unity-gain or inverting buffers for low-speed communications, instrumentation and interface conditioning. The 1.2 MHz gain-bandwidth product is suitable for baseband signals, while the wide supply range permits operation from 5 V, 12 V or 24 V rails. Its improved 2 kV ESD rating adds robustness at exposed connector inputs when protection networks are also used. For higher data rates, differential channels or very low jitter, a dedicated interface amplifier is the better selection.
推荐
推荐产品汇总
工程参考数据: LM2902KDBRG4 ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | LM2902KDBR |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 14-SSOP | 14-SSOP - same |
| Amplifier Configuration | Quad general-purpose operational amplifier | Quad general-purpose operational amplifier |
| Supply Voltage Range | 3 V to 26 V | 3 V to 26 V |
| Gain-Bandwidth Product | 1.2 MHz | 1.2 MHz |
| Slew Rate | 0.5 V/μs | 0.5 V/μs |
| Output Current | 60 mA per channel | 60 mA per channel |
| Input Bias Current | 0.5 μA typical | 0.5 μA typical |
| Input Offset Current | 20 nA typical | 20 nA typical |
| Operating Temperature Range | -40°C to +125°C | -40°C to +125°C |
关键差异点
- Four amplifiers in one 14-SSOP package (对比 LM2902KDBR)
- Wide 26 V supply capability (对比 LM2902KDBR)
- Improved ESD protection for exposed analog interfaces (对比 LM2902KDBR)
设计说明
Place the supply bypass capacitor close to pin 11, V+, and connect pin 4, V−, to a low-impedance ground plane. Route input and output traces away from the supply-capacitor return path to reduce injection of switching noise. Because four channels share the same supply pins, a local bypass arrangement supports all amplifiers but can also couple channel-to-channel disturbance through a common impedance.
Do not assume rail-to-rail input operation. The input common-mode range extends approximately 0.5 V below the positive rail, so signals that approach V+ may require attenuation, level shifting or a bias reference. Likewise, output current above 60 mA per channel is outside the device rating. Check the output saturation and common-mode limits in the manufacturer datasheet for the intended supply and load conditions.
Use feedback resistors that keep closed-loop gain well below the 1.2 MHz gain-bandwidth product and verify stability with the actual load capacitance. Very small feedback resistors may cause the amplifier to drive capacitive loads into oscillation. When four channels process related signals, keep sensitive inputs away from adjacent output pins and use separate return paths where channel-to-channel coupling would be critical.
合规信息
The LM2902K family documentation identifies AEC-Q100 qualification for automotive applications and improved ESD protection. Current RoHS, REACH, lead-free, halogen-free and conflict-minerals declarations should be confirmed for the exact orderable MPN.