Texas Instruments

LM2904LVIDDFR - 5.5V Dual 1MHz Op Amp | Texas Instruments

MPN: LM2904LVIDDFR ✓ সক্রিয়
5.5 V Vdss 90 uA Id TSOT-23-8 Package
সর্বনিম্ন অর্ডার পরিমাণ: 1 |

LM2904LVIDDFR সারাংশ

The Texas Instruments LM2904LVIDDFR is a dual, low-voltage operational amplifier with a 5.5 V maximum supply voltage, 1 MHz gain-bandwidth product, and 3 mV output offset voltage, housed in an 8-pin TSOT-23 package. Each amplifier channel provides independent input, output, power, and feedback connections, allowing one package to implement two signal-processing functions.

An operational amplifier is an analog amplifier whose high open-loop gain is controlled by external feedback components. Within the power-management semiconductor hierarchy, the LM2904LV belongs to the broader operational-amplifier family, combining low-voltage compatibility, low power consumption, and general-purpose signal conditioning in one dual-channel device. The LM2904LV family is intended for portable equipment, industrial controls, sensors, communications, and other low-voltage systems.

Key characteristics include a 2.7 V to 5.5 V supply range, approximately 90 uA supply current, a typical slew rate of 0.5 V/us, and rail-to-rail output swing. The 1 MHz gain-bandwidth product supports moderate-frequency amplification, while the 3 mV offset-voltage figure defines the typical input imbalance that must be considered when operating near the output range limits. These characteristics make the device suitable for battery-powered instrumentation and general-purpose analog front ends.

The dual architecture reduces component count and board area compared with two separate single-channel amplifiers. Each channel can be configured as an inverting amplifier, a non-inverting amplifier, a comparator-like comparator configuration, or an analog buffer when operated with suitable feedback and loading. Independent channel use provides flexibility, although common-mode and output-swing limitations still apply to both channels.

Typical uses include current-sense amplifier front ends, sensor signal conditioning, low-frequency active filters, audio preamplification, industrial interface circuits, and portable measurement equipment. In current sensing, the device can amplify the small voltage developed across a low-value shunt resistor. In sensor interfaces, it can provide gain or impedance conversion before an ADC input. Its low 90 uA supply-current characteristic is particularly useful in battery-operated equipment.

When designing around the LM2904LVIDDFR, verify the input common-mode range and output swing against the actual signal amplitude. Keep feedback-loop routing compact, provide local supply bypassing, and avoid placing the input node beside high-current switching paths. Check the 5.5 V maximum supply rating and ensure the 2.7 V lower operating limit is sufficient for the complete system supply range.

This product page consolidates the manufacturer specifications, package information, practical application guidance, and verified substitution assessment for the LM2904LVIDDFR. It also distinguishes confirmed drop-in candidates from devices that require a package or functional change, helping engineers evaluate replacements without changing PCB requirements.

এর জন্য ড্রপ-ইন বিকল্প LM2904LVIDDFR — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।

LM2904LVIDDFR

✅ ড্রপ-ইন
Texas Instruments
📦 SOT-23-THN (DDF)
2 channels · 5.5 V · 2.7 V to 5.5 V · 1 MHz · 3 mV · 0.5 V/us · 90 uA · Rail-to-rail output

মূল্যের জন্য যোগাযোগ করুন

ডেটাশিট দেখুন →

LM2904LVIDDFR সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য

Number of Amplifier Channels 2 channels
Maximum Supply Voltage 5.5 V
Operating Supply Voltage Range 2.7 V to 5.5 V
Gain-Bandwidth Product 1 MHz
Typical Output Offset Voltage 3 mV
Typical Slew Rate 0.5 V/us
Typical Supply Current 90 uA
Output Swing Rail-to-rail output
প্যাকেজ TSOT-23-8
মাউন্টিং টাইপ Surface mount
Product Classification Standard general-purpose amplifier
Automotive and Industrial Positioning Optimized for automotive and industrial applications
RoHS স্ট্যাটাস Compliant
Moisture Sensitivity Level MSL 1 at 260 C

LM2904LVIDDFR tsot-23-8 পিন কনফিগারেশন গাইড

LM2904LVIDDFR (tsot-23-8 প্যাকেজ)-এর পিন কনফিগারেশন। এই অ্যানালগ কম্পোনেন্টে ইনপুট, আউটপুট ও পাওয়ার সাপ্লাই পিন রয়েছে। অফসেট নাল, কম্পেনসেশন ও এনেবল পিন কনফিগারেশনের জন্য প্রস্তুতকারকের ডেটাশিট দেখুন। সিগন্যাল কন্ডিশনিং ও অ্যামপ্লিফায়ার সার্কিটের জন্য আদর্শ।

LM2904LVIDDFR-এর জন্য tsot-23-8 প্যাকেজ পিনআউট ডায়াগ্রাম

এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি LM2904LVIDDFR.

দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।

সাধারণ ব্যবহার

LM2904LVIDDFR এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Low-Voltage Current-Sense Amplifier, Battery-Powered Sensor Signal Conditioning, Industrial Low-Frequency Active Filter, Portable Audio Preamplifier, Communications Interface Conditioning, Portable Test and Measurement Front End.

⚡

Low-Voltage Current-Sense Amplifier

The LM2904LVIDDFR can amplify the small differential voltage generated by a low-value shunt resistor in a 2.7 V to 5.5 V measurement system. Its 1 MHz gain-bandwidth product is suitable for moderate-bandwidth current measurements, while the 3 mV typical output offset must be included in the accuracy budget. Use a feedback network that keeps the amplifier stable with the shunt resistance, input capacitance, and ADC sampling network. A single channel can provide gain while the second channel can monitor the scaled output or provide an additional signal path.

🧩

Battery-Powered Sensor Signal Conditioning

The LM2904LVIDDFR suits battery-powered sensor interfaces because it accepts a 2.7 V to 5.5 V supply and typically draws about 90 uA. One channel can amplify a resistive or transducer output, while the other can buffer a reference or temperature signal. The 1 MHz gain-bandwidth product supports sensors with bandwidths below the amplifier's useful operating range. Designers should verify input bias current against high source impedances and check that the sensor voltage remains within the specified common-mode range throughout battery discharge.

🏭

Industrial Low-Frequency Active Filter

The dual LM2904LVIDDFR can implement two active-filter sections in a compact 2.7 V to 5.5 V industrial control module. Its 1 MHz gain-bandwidth product provides ample bandwidth for many low-frequency measurement and control loops, and the typical 0.5 V/us slew rate helps preserve large-signal response. Component tolerances in the feedback network determine filter accuracy. Place the amplifier, resistor, and capacitor network close together, maintain short feedback paths, and test both channels for stable startup and acceptable phase margin.

🎧

Portable Audio Preamplifier

The LM2904LVIDDFR can provide low-level audio preamplification in portable equipment operating from 2.7 V to 5.5 V. Its dual-channel organization supports left and right signal paths, while the 1 MHz bandwidth covers common audio-band applications. The 3 mV typical output offset can be important when gains are high, so an AC-coupled input or offset-null arrangement should be considered where signal-chain headroom is limited. Confirm the output load, headroom, and distortion at the intended signal level.

🌐

Communications Interface Conditioning

The LM2904LVIDDFR can condition slow communications, control, or logic-level signals in low-voltage systems. The two independent channels can amplify a receive path and condition a control or threshold path in the same TSOT-23-8 package. Its 1 MHz gain-bandwidth product is suitable for many baseband and supervisory signals, but it is not intended as a high-speed differential line receiver. Keep sensitive inputs away from switching nodes and use the shortest practical feedback traces to reduce noise pickup.

📱

Portable Test and Measurement Front End

The LM2904LVIDDFR is appropriate for compact test and measurement front ends where the signal path must operate below 5.5 V. One channel can amplify an input measurement while the other buffers a reference or monitor a control point. Its approximately 90 uA supply current helps limit battery drain, and its 1 MHz bandwidth covers many low-speed measurements. For precision work, include the 3 mV typical output offset in the uncertainty calculation and evaluate input bias current, noise, and ADC input loading.

সুপারিশকৃত পণ্যের সারসংক্ষেপ

LM2904LVIDDFR Texas Instruments ব্যবহৃত হয়: Low-Voltage Current-Sense Amplifier, Battery-Powered Sensor Signal Conditioning, Industrial Low-Frequency Active Filter, Portable Audio Preamplifier, Communications Interface Conditioning, Portable Test and Measurement Front End LM2904LV Parent family for low-voltage dual amplifiers ব্যবহৃত হয়: Low-Voltage Current-Sense Amplifier, Battery-Powered Sensor Signal Conditioning, Industrial Low-Frequency Active Filter, Portable Audio Preamplifier, Communications Interface Conditioning, Portable Test and Measurement Front End
What is the operating voltage of LM2904LVIDDFR?
The LM2904LVIDDFR operates from 2.7 V to 5.5 V, making it a low-voltage dual operational amplifier for portable, industrial, and automotive-related signal-conditioning systems. According to the Texas Instruments LM2904LV product page and manufacturer datasheet, its maximum supply voltage is 5.5 V. The dual package contains two independent amplifier channels, while the supply pins are shared. Confirm that system startup, transient excursions, and regulator tolerances remain within the device limits before beginning PCB design.
What are the key specifications of LM2904LVIDDFR that engineers should know?
The LM2904LVIDDFR is a dual operational amplifier with a 1 MHz gain-bandwidth product, typical 3 mV output offset voltage, 0.5 V/us typical slew rate, and approximately 90 uA supply current. Its 2.7 V to 5.5 V supply range and rail-to-rail output swing suit low-voltage systems. Texas Instruments identifies the device as a standard general-purpose amplifier in an 8-pin TSOT-23 package.
Where can I download the LM2904LVIDDFR datasheet PDF?
The authoritative LM2904LV datasheet is linked from the Texas Instruments LM2904LV product page at https://www.ti.com/product/LM2904LV. The manufacturer datasheet provides the electrical characteristics, pin configuration, typical application circuits, and ordering information for the LM2904LV family. Use the LM2904LV document rather than a standard 26 V LM2904 datasheet because the maximum supply ratings, gain-bandwidth product, and electrical limits differ.
Where can I find the LM2904LVIDDFR pinout?
The LM2904LVIDDFR pin configuration is documented in the LM2904LV manufacturer datasheet and its package drawing, which identifies the eight TSOT-23 terminals and the two independent amplifier channels. Use that pin-description and package-outline section when assigning PCB tracks and selecting the exposed-pad or thermal treatment appropriate to the manufacturer footprint. The LM2904LVIDDFR designation uses TI's DDF package suffix, so compare land patterns against the package drawing rather than relying only on a generic TSOT-23-8 image.
Is LM2904LVIDDFR the same as LM2904LV?
The LM2904LVIDDFR is the specific orderable device within Texas Instruments' LM2904LV family, not a generic synonym for every LM2904LV package. It is a dual low-voltage operational amplifier specified for a 2.7 V to 5.5 V supply range, 1 MHz gain-bandwidth product, and 3 mV typical output offset voltage. The standard LM2904 is a different 26 V, 700 kHz device, so it must not be substituted without a careful electrical and package review.
What can replace the LM2904LVIDDFR?
A true drop-in replacement must use the same TSOT-23-8 footprint, preserve the eight-terminal dual-amplifier pin arrangement, and remain within approximately 30% of the key 2.7 V to 5.5 V supply, 1 MHz bandwidth, 3 mV offset, and 0.5 V/us slew-rate ratings. No confirmed five-part set of same-footprint alternatives was established for this exact MPN. Treat devices in SOIC, TSSOP, VSSOP, or single-amplifier packages as redesign candidates rather than direct replacements.
Is LM2904LVIDDFR suitable for current sensing?
The LM2904LVIDDFR is suitable for low-frequency current sensing when the shunt voltage remains inside the amplifier's input and output ranges. Its 1 MHz gain-bandwidth product supports moderate-bandwidth measurements, while the 3 mV typical output offset establishes the baseline error that must be included in the measurement budget. Texas Instruments describes the LM2904LV as a standard general-purpose amplifier, so precision current measurement may require offset calibration, gain error analysis, and attention to common-mode limits.
What is the difference between LM2904LVIDDFR and LM2904?
The LM2904LVIDDFR is rated for a 2.7 V to 5.5 V supply and has a 1 MHz gain-bandwidth product, while the standard Texas Instruments LM2904 is rated for operation up to 26 V with a 700 kHz gain-bandwidth product. The first is a low-voltage member of the LM2904LV family; the second is a higher-voltage classic LM2904. Their supply and performance ratings differ enough that a replacement must be checked for stability, output swing, input range, power, and exact package pinout.
When should I choose LM2904LVIDDFR over a higher-voltage operational amplifier?
Choose the LM2904LVIDDFR when the system supply is between 2.7 V and 5.5 V, low supply current is valuable, and moderate signal bandwidth is sufficient. Its 1 MHz gain-bandwidth product, 0.5 V/us typical slew rate, and approximately 90 uA supply current are aligned with low-voltage instrumentation. A higher-voltage amplifier may be preferable when the signal or supply can exceed 5.5 V, when greater bandwidth is required, or when the additional operating range is essential.
Is LM2904LVIDDFR suitable for battery-powered sensor interfaces?
The LM2904LVIDDFR is well matched to battery-powered sensor interfaces because its 2.7 V lower supply limit supports low-voltage operation and its approximately 90 uA supply current limits quiescent consumption. Its dual-channel configuration can process two sensor signals or combine amplification and buffering in one package. The 1 MHz bandwidth is adequate for many slow sensors, but designers should verify output swing, offset error, input bias current, and the sensor source impedance.
How much current does LM2904LVIDDFR consume?
The LM2904LVIDDFR has a typical supply current of approximately 90 uA in its nominal low-voltage operating mode. Texas Instruments lists the device as a low-power, industry-standard operational amplifier. Actual board consumption can vary with supply voltage, input voltages, output loading, channel utilization, and operating mode, so use the manufacturer electrical-characteristics tables for worst-case design calculations. Place the bypass capacitor near the shared supply pins to manage supply impedance.
Can LM2904LVIDDFR drive a sensor output directly?
The LM2904LVIDDFR can buffer or amplify many low-frequency sensor outputs, but the source impedance and signal range must be checked first. High-impedance sensors may interact with input bias current, while sensor outputs near either supply rail can exceed the allowed common-mode or output-swing range. Its rail-to-rail output improves output range utilization, but it does not automatically make the input common-mode range rail-to-rail. Consult the manufacturer input common-mode and output-swing curves before selecting it.
What is the best cross-brand equivalent for LM2904LVIDDFR?
The best cross-brand equivalent is the device that combines the same TSOT-23-8 footprint, matching pin configuration, 2.7 V to 5.5 V supply compatibility, and comparable 1 MHz-class bandwidth and offset performance. No cross-brand candidate was confirmed from the available substitution results, so naming one would overstate the evidence. A candidate in a different package should be treated as a redesign unless its manufacturer explicitly identifies the LM2904LVIDDFR footprint and pinout as compatible.
Is LM2904LVIDDFR in stock and what is its lead time?
Current stock and production lead time should be requested through the Request a Quote form on this page because availability can change by package, quantity, and regional inventory. The Texas Instruments product page remains the primary source for lifecycle and ordering information. The LM2904LVIDDFR ordering code identifies the DDF tape-and-reel package, so include the complete MPN and required quantity when requesting a quotation for production planning.
What is the price of LM2904LVIDDFR?
The current commercial price and quantity availability for the LM2904LVIDDFR should be obtained through the Request a Quote form on this page. Pricing can vary with order quantity, package, inventory, and market conditions, so a static amount may not represent a purchasable production offer. Submit the exact MPN, target quantity, shipment location, and required production date to obtain a current quotation for the DDF package.
Is LM2904LVIDDFR RoHS compliant?
The LM2904LVIDDFR is listed as RoHS compliant in the component compliance information, and its moisture sensitivity designation is MSL 1 at 260 C. According to the Texas Instruments product and datasheet resources, the LM2904LV family is also positioned for automotive and industrial systems. AEC-Q100 qualification, REACH status, lead-free status, and halogen-free status should be confirmed from the exact orderable MPN before using those claims in a formal product-compliance document.

এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা LM2904LVIDDFR — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।

নির্বাচন গাইড

Choose the LM2904LVIDDFR for compact, low-voltage systems that operate from 2.7 V to 5.5 V and need two general-purpose amplifier channels. Its approximately 90 uA supply current is useful in battery-powered equipment, while the 1 MHz bandwidth and 0.5 V/us typical slew rate suit low-frequency sensing, filtering, buffering, and audio-preamplification applications. Select the standard LM2904 instead when operation above 5.5 V or a 26 V maximum supply rating is essential. Select the LM321LVIDCKR when only one amplifier channel is needed and a smaller single-amplifier package is preferred. No confirmed TSOT-23-8 pin-compatible alternatives were established, so engineers should not assume that devices in SOIC, TSSOP, VSSOP, or single-amplifier packages can replace the LM2904LVIDDFR without a PCB change.

বিকল্পের সাথে তুলনা

পারামিটার এই পণ্য
Package TSOT-23-8
Brand Texas Instruments
Amplifier Channels 2 channels
Operating Supply Voltage Range 2.7 V to 5.5 V
Maximum Supply Voltage 5.5 V
Gain-Bandwidth Product 1 MHz
Typical Output Offset Voltage 3 mV
Typical Slew Rate 0.5 V/us
Typical Supply Current 90 uA
Output Swing Rail-to-rail output

মূল পার্থক্যসমূহ

  • Low-voltage operation in a compact dual-channel package (বনামLM2904)
  • Lower quiescent supply demand for portable designs (বনামLM2904)
  • Two independent amplifier functions in one package (বনামLM321LVIDCKR)

ডিজাইন নোট

Use a local bypass capacitor on the device supply pins and route it with a short ground return to reduce supply impedance. Keep the 5.5 V maximum rating visible during schematic review, especially when the amplifier is powered from an unregulated source. For battery systems, verify that the supply remains above the 2.7 V operating limit at full battery discharge and under the worst load condition.

Place input, feedback, and decoupling components close to their associated IC pins. Route feedback traces away from power switching nodes and keep each channel's input path as short as practical. The TSOT-23-8 footprint is compact, so stable component placement and careful ground return routing help prevent added noise, oscillation, or crosstalk between the two amplifier channels.

Do not treat rail-to-rail output as proof of a rail-to-rail input common-mode range. Check the manufacturer input range, output swing, and load-current curves at the intended supply voltage. Also include the typical 3 mV output offset when designing high-gain or precision signal paths, and use the LM2904LV datasheet rather than the standard LM2904 datasheet when selecting electrical limits.

কমপ্লায়েন্স তথ্য

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
লিড ফ্রি
Unknown
হ্যালোজেন ফ্রি
Unknown
কনফ্লিক্ট মিনারেলস
Unknown

RoHS compliance and MSL 1 at 260 C are listed for the component. AEC-Q100 qualification, REACH status, lead-free status, halogen-free status, and conflict-minerals status are not established for the exact orderable MPN.

ডেটা যাচাই করা হয়েছে: 2026-11-09 — ডেটা XAIPART-এর কম্পোনেন্ট ইঞ্জিনিয়ারিং টিম দ্বারা যাচাই ও কিউরেট করা হয়েছে

সম্পর্কিত অনুসন্ধান

LM2904LVIDDFR datasheet LM2904LVIDDFR pinout LM2904LVIDDFR datasheet pdf LM2904LVIDDFR equivalent LM2904LVIDDFR replacement LM2904LVIDDFR footprint LM2904LVIDDFR spice model LM2904LVIDDFR price LM2904LVIDDFR stock Texas Instruments LM2904LVIDDFR LM2904LVIDDFR TSOT-23-8 pinout LM2904LV 5.5V op amp LM2904LVIDDFR current sensing LM2904LVIDDFR vs LM2904 LM2904LVIDDFR application circuit

সম্পর্কিত কম্পোনেন্ট ও শর্তাবলী

Texas Instruments LM2904LVIDDFR LM2904LV LM2904 LM321LVIDCKR operational amplifier dual amplifier analog amplifier signal conditioning current-sense amplifier gain-bandwidth product output offset voltage slew rate quiescent supply current common-mode input range rail-to-rail output TSOT-23-8 surface-mount package RoHS MSL 1 REACH AEC-Q100 industrial control battery-powered instrumentation
তাৎক্ষণিক বিলওয়াছে রেকোজিউইট
সম্পূর্ণ বিবরণ পূরণ করুন — আমাদের সেলস টিম 24 ঘণ্টার মধ্যে উত্তর দেবে
পার্ট নম্বর উৎপাদক প্যাকেজ QTY লক্ষ্যমূল্য প্রসারিত
✓
বিল প্রস্তুত করা হয়েছে!

আমরা ২৪ ঘণ্টার মধ্যে আপনার ইমেইলে প্রত্যুত্তর দেব

1
RFQ জমা হয়েছে
2
কোটেশন পাওয়া গেছে
3
অর্ডার দেওয়া হয়েছে
4
পেমেন্ট
5
শিপ করা হয়েছে
6
ডেলিভারি হয়েছে
RFQ বিবরণ দেখুন