LM2904LVIDDFR - 5.5V Dual 1MHz Op Amp | Texas Instruments
MPN: LM2904LVIDDFR ✓ نشطLM2904LVIDDFR نظرة عامة
An operational amplifier is an analog amplifier whose high open-loop gain is controlled by external feedback components. Within the power-management semiconductor hierarchy, the LM2904LV belongs to the broader operational-amplifier family, combining low-voltage compatibility, low power consumption, and general-purpose signal conditioning in one dual-channel device. The LM2904LV family is intended for portable equipment, industrial controls, sensors, communications, and other low-voltage systems.
Key characteristics include a 2.7 V to 5.5 V supply range, approximately 90 uA supply current, a typical slew rate of 0.5 V/us, and rail-to-rail output swing. The 1 MHz gain-bandwidth product supports moderate-frequency amplification, while the 3 mV offset-voltage figure defines the typical input imbalance that must be considered when operating near the output range limits. These characteristics make the device suitable for battery-powered instrumentation and general-purpose analog front ends.
The dual architecture reduces component count and board area compared with two separate single-channel amplifiers. Each channel can be configured as an inverting amplifier, a non-inverting amplifier, a comparator-like comparator configuration, or an analog buffer when operated with suitable feedback and loading. Independent channel use provides flexibility, although common-mode and output-swing limitations still apply to both channels.
Typical uses include current-sense amplifier front ends, sensor signal conditioning, low-frequency active filters, audio preamplification, industrial interface circuits, and portable measurement equipment. In current sensing, the device can amplify the small voltage developed across a low-value shunt resistor. In sensor interfaces, it can provide gain or impedance conversion before an ADC input. Its low 90 uA supply-current characteristic is particularly useful in battery-operated equipment.
When designing around the LM2904LVIDDFR, verify the input common-mode range and output swing against the actual signal amplitude. Keep feedback-loop routing compact, provide local supply bypassing, and avoid placing the input node beside high-current switching paths. Check the 5.5 V maximum supply rating and ensure the 2.7 V lower operating limit is sufficient for the complete system supply range.
This product page consolidates the manufacturer specifications, package information, practical application guidance, and verified substitution assessment for the LM2904LVIDDFR. It also distinguishes confirmed drop-in candidates from devices that require a package or functional change, helping engineers evaluate replacements without changing PCB requirements.
بدائل مباشرة لـ LM2904LVIDDFR — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.
LM2904LVIDDFR
✅ بديل مباشرتواصل لمعرفة السعر
عرض ورقة البيانات ←LM2904LVIDDFR الحدود القصوى والخصائص الكهربائية
| Number of Amplifier Channels | 2 channels |
| Maximum Supply Voltage | 5.5 V |
| Operating Supply Voltage Range | 2.7 V to 5.5 V |
| Gain-Bandwidth Product | 1 MHz |
| Typical Output Offset Voltage | 3 mV |
| Typical Slew Rate | 0.5 V/us |
| Typical Supply Current | 90 uA |
| Output Swing | Rail-to-rail output |
| العلبة | TSOT-23-8 |
| نوع التركيب | Surface mount |
| Product Classification | Standard general-purpose amplifier |
| Automotive and Industrial Positioning | Optimized for automotive and industrial applications |
| حالة RoHS | Compliant |
| Moisture Sensitivity Level | MSL 1 at 260 C |
دليل تكوين أطراف LM2904LVIDDFR tsot-23-8
تكوين الأطراف لـ LM2904LVIDDFR (حزمة tsot-23-8). يتميز هذا المكوّن التناظري بأطراف الإدخال والإخراج وإمداد الطاقة. راجع ورقة بيانات الشركة المصنعة لتكوينات طرف إلغاء الإزاحة والتعويض والتمكين. مثالي لدوائر تكييف الإشارة والمضخمات.
لا تتوفر بيانات مفصلة لمخطط التوصيلات لـ LM2904LVIDDFR.
راجع ورقة البيانات للحصول على تكوين الأطراف الكامل.
التطبيقات النموذجية
LM2904LVIDDFR مناسب لـ 6 التطبيقs: Low-Voltage Current-Sense Amplifier, Battery-Powered Sensor Signal Conditioning, Industrial Low-Frequency Active Filter, Portable Audio Preamplifier, Communications Interface Conditioning, Portable Test and Measurement Front End.
Low-Voltage Current-Sense Amplifier
The LM2904LVIDDFR can amplify the small differential voltage generated by a low-value shunt resistor in a 2.7 V to 5.5 V measurement system. Its 1 MHz gain-bandwidth product is suitable for moderate-bandwidth current measurements, while the 3 mV typical output offset must be included in the accuracy budget. Use a feedback network that keeps the amplifier stable with the shunt resistance, input capacitance, and ADC sampling network. A single channel can provide gain while the second channel can monitor the scaled output or provide an additional signal path.
موصى به
Battery-Powered Sensor Signal Conditioning
The LM2904LVIDDFR suits battery-powered sensor interfaces because it accepts a 2.7 V to 5.5 V supply and typically draws about 90 uA. One channel can amplify a resistive or transducer output, while the other can buffer a reference or temperature signal. The 1 MHz gain-bandwidth product supports sensors with bandwidths below the amplifier's useful operating range. Designers should verify input bias current against high source impedances and check that the sensor voltage remains within the specified common-mode range throughout battery discharge.
موصى به
Industrial Low-Frequency Active Filter
The dual LM2904LVIDDFR can implement two active-filter sections in a compact 2.7 V to 5.5 V industrial control module. Its 1 MHz gain-bandwidth product provides ample bandwidth for many low-frequency measurement and control loops, and the typical 0.5 V/us slew rate helps preserve large-signal response. Component tolerances in the feedback network determine filter accuracy. Place the amplifier, resistor, and capacitor network close together, maintain short feedback paths, and test both channels for stable startup and acceptable phase margin.
موصى به
Portable Audio Preamplifier
The LM2904LVIDDFR can provide low-level audio preamplification in portable equipment operating from 2.7 V to 5.5 V. Its dual-channel organization supports left and right signal paths, while the 1 MHz bandwidth covers common audio-band applications. The 3 mV typical output offset can be important when gains are high, so an AC-coupled input or offset-null arrangement should be considered where signal-chain headroom is limited. Confirm the output load, headroom, and distortion at the intended signal level.
موصى به
Communications Interface Conditioning
The LM2904LVIDDFR can condition slow communications, control, or logic-level signals in low-voltage systems. The two independent channels can amplify a receive path and condition a control or threshold path in the same TSOT-23-8 package. Its 1 MHz gain-bandwidth product is suitable for many baseband and supervisory signals, but it is not intended as a high-speed differential line receiver. Keep sensitive inputs away from switching nodes and use the shortest practical feedback traces to reduce noise pickup.
موصى به
Portable Test and Measurement Front End
The LM2904LVIDDFR is appropriate for compact test and measurement front ends where the signal path must operate below 5.5 V. One channel can amplify an input measurement while the other buffers a reference or monitor a control point. Its approximately 90 uA supply current helps limit battery drain, and its 1 MHz bandwidth covers many low-speed measurements. For precision work, include the 3 mV typical output offset in the uncertainty calculation and evaluate input bias current, noise, and ADC input loading.
موصى به
ملخص المنتجات الموصى بها
بيانات مرجعية هندسية لـ LM2904LVIDDFR — المقارنة وإرشادات التصميم ومعلومات الامتثال.
دليل الاختيار
المقارنة مع البدائل
| المعامل | هذا المنتج |
|---|---|
| Package | TSOT-23-8 |
| Brand | Texas Instruments |
| Amplifier Channels | 2 channels |
| Operating Supply Voltage Range | 2.7 V to 5.5 V |
| Maximum Supply Voltage | 5.5 V |
| Gain-Bandwidth Product | 1 MHz |
| Typical Output Offset Voltage | 3 mV |
| Typical Slew Rate | 0.5 V/us |
| Typical Supply Current | 90 uA |
| Output Swing | Rail-to-rail output |
أبرز الفروقات
- Low-voltage operation in a compact dual-channel package (مقابلLM2904)
- Lower quiescent supply demand for portable designs (مقابلLM2904)
- Two independent amplifier functions in one package (مقابلLM321LVIDCKR)
ملاحظات التصميم
Use a local bypass capacitor on the device supply pins and route it with a short ground return to reduce supply impedance. Keep the 5.5 V maximum rating visible during schematic review, especially when the amplifier is powered from an unregulated source. For battery systems, verify that the supply remains above the 2.7 V operating limit at full battery discharge and under the worst load condition.
Place input, feedback, and decoupling components close to their associated IC pins. Route feedback traces away from power switching nodes and keep each channel's input path as short as practical. The TSOT-23-8 footprint is compact, so stable component placement and careful ground return routing help prevent added noise, oscillation, or crosstalk between the two amplifier channels.
Do not treat rail-to-rail output as proof of a rail-to-rail input common-mode range. Check the manufacturer input range, output swing, and load-current curves at the intended supply voltage. Also include the typical 3 mV output offset when designing high-gain or precision signal paths, and use the LM2904LV datasheet rather than the standard LM2904 datasheet when selecting electrical limits.
معلومات الامتثال
RoHS compliance and MSL 1 at 260 C are listed for the component. AEC-Q100 qualification, REACH status, lead-free status, halogen-free status, and conflict-minerals status are not established for the exact orderable MPN.