LM2904VN - Dual Op Amp, 1MHz GBW, PDIP-8 | onsemi
MPN: LM2904VN ✓ সক্রিয়LM2904VN সারাংশ
A dual operational amplifier integrates two matched, frequency-compensated op-amp cores on a single silicon die within one package. As a subcategory of the linear amplifier family, general-purpose op-amps sit within the broader hierarchy of voltage amplifiers and analog signal-conditioning ICs, providing gain, buffering, filtering, and comparison functions in analog front ends. The dual configuration halves board space and improves channel-to-channel matching compared with two single op-amps.
Key features include low power drain, a common-mode input voltage range that extends to ground/VEE (input common-mode includes the negative rail), and single-supply or split-supply operation. These characteristics let designers build ground-referenced signal conditioning directly from a single positive rail without a negative supply, which is the defining advantage of the LM358/LM2904 amplifier family.
Technically, the LM2904VN derives from the circuit design perfected for the industry-standard LM324 quad op-amp: the LM358 series is equivalent to one-half of an LM324. The amplifier delivers approximately 70 dB of open-loop gain, low input bias current (about 45 nA typical per distributor characterization data), and internal frequency compensation that guarantees unity-gain stability without external components.
Typical applications include transducer amplifiers, DC gain blocks, active filters, comparators, and general low-frequency signal conditioning in industrial controls, automotive subsystems, and battery-powered instruments.
A key design consideration: the output stage is not rail-to-rail and can sink only limited current near ground, so loading the output with a resistor to VEE (for example, 2 kOhm) improves output swing close to the negative rail.
This page adds value beyond the manufacturer datasheet by consolidating drop-in cross-references, a parameter comparison table against pin-compatible alternatives, and practical design notes in one place.
এর জন্য ড্রপ-ইন বিকল্প LM2904VN — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
এই সিরিজের ভ্যারিয়েন্ট
একই সিরিজের মডেল যেগুলো drop-in compatible LM2904VN (একই form factor এবং footprint) — পার্থক্য রয়েছে Package, Mounting Type, Slew Rate, Amplifier Type, Frequency Compensation.
LM2904NG
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →LM2904BIDR
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →LM2904N
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →LM358N
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →LM2904VN সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য
| Amplifier Type | General Purpose / Instrumentation, Op Amp, Buffer |
| Number of Circuits | 2 |
| Gain Bandwidth Product | 1 MHz |
| Slew Rate | 0.6 V/us |
| Supply Voltage Range (Single) | 3 V to 26 V |
| Supply Voltage Range (Total) | 3 V to 32 V |
| Supply Voltage Range (Split) | +/-1.5 V to +/-16 V |
| Input Bias Current | 45 nA |
| Open Loop Gain | 70 dB |
| Common Mode Input Range | Extends to ground / VEE |
| Supply Operation | Single supply or split supply |
| প্যাকেজ | 8-PDIP (0.300 in, 7.62 mm) |
| মাউন্টিং টাইপ | Through Hole |
| Power Drain | Low power drain (per manufacturer description) |
LM2904VN পিন কনফিগারেশন
| পিন 1 | OUT A — Output of amplifier A |
| পিন 2 | IN A- — Inverting input of amplifier A |
| পিন 3 | IN A+ — Non-inverting input of amplifier A |
| পিন 4 | GND / V- — Ground or negative supply |
| পিন 5 | IN B+ — Non-inverting input of amplifier B |
| পিন 6 | IN B- — Inverting input of amplifier B |
| পিন 7 | OUT B — Output of amplifier B |
| পিন 8 | VCC / V+ — Positive supply |
সাধারণ ব্যবহার
LM2904VN এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Transducer Amplification, DC Gain Blocks, Active Filters, Comparator Functions, Battery-Powered and Portable Instruments, Automotive Signal Conditioning.
Transducer Amplification
The LM2904VN is a classic choice for amplifying low-level signals from transducers such as thermistors, strain-gauge bridges, and photodiodes in single-supply industrial equipment. Because its common-mode input range extends to ground/VEE, sensors referenced to 0 V can be connected directly to the non-inverting input without level shifting or a negative rail, at supply voltages from 3 V up to 26 V. Typical gain configurations of 10x to 100x remain well within the 1 MHz gain-bandwidth product, delivering usable closed-loop bandwidth from roughly 10 kHz down to 1 kHz, which is ample for thermal and mechanical process variables. The second amplifier channel in the same PDIP-8 package is commonly used for filtering or output scaling, saving board space and improving channel matching.
সুপারিশকৃত
DC Gain Blocks
As a DC gain block, the LM2904VN provides stable non-inverting or inverting gain for scaling sensor outputs, reference levels, and control-loop feedback signals. With approximately 70 dB of open-loop gain, a closed-loop gain of 100 (40 dB) retains about 30 dB of loop gain, keeping gain error and distortion low at DC and low frequencies. The device operates from a single 3 V to 26 V supply or +/-16 V split rails, so the same circuit scales from battery products to industrial 24 V systems. Internal frequency compensation guarantees unity-gain stability with no external capacitor, simplifying BOM. Designers should note the limited output sink near ground and add a pull-down resistor to VEE when output levels close to the negative rail are required.
সুপারিশকৃত
Active Filters
The LM2904VN implements Sallen-Key and multiple-feedback active filters in the audio and low-frequency instrumentation range. With a 1 MHz gain-bandwidth product, filter corner frequencies up to roughly 10 kHz at unity-gain Sallen-Key topologies are achievable with minimal Q degradation, and multi-stage anti-alias filters for modest ADC sampling rates fit comfortably. Single-supply operation with inputs valid to ground/VEE allows mid-supply biasing with simple resistor dividers, avoiding negative rails entirely. The dual channels permit a two-pole filter section per PDIP-8 package. The 0.6 V/us slew rate supports full-scale sinusoids up to roughly 95 kHz, so designers should verify slew headroom for large-signal high-frequency filter outputs.
সুপারিশকৃত
Comparator Functions
Although dedicated comparators are faster, the LM2904VN is widely used as a low-speed comparator for threshold detection, over-voltage flags, and window monitors where response times of tens of microseconds are acceptable. The input common-mode range extending to ground/VEE enables ground-referenced threshold sensing directly from a single rail, and the wide 3 V to 26 V supply range matches unregulated industrial supplies. Open-loop gain of about 70 dB yields sharp switching thresholds, while the 0.6 V/us slew rate sets propagation delay expectations in the 10 us-class region. Designers should add hysteresis with positive feedback and avoid driving capacitive loads directly to prevent oscillation through slow output transitions.
সুপারিশকৃত
Battery-Powered and Portable Instruments
The low power drain of the LM2904VN family makes it suitable for battery-operated measurement and monitoring products operating from 3 V upward. A single PDIP-8 package supplies two amplifier channels for front-end gain and active filtering while drawing minimal quiescent current relative to the system budget, and operation down to 3 V total supply accommodates two-cell or single-cell-boosted architectures. The through-hole PDIP package also simplifies prototyping, rework, and educational instrument builds. For battery designs, note that the output stage cannot swing fully to the rails, so define signal ranges with 1 V-class headroom from either rail to preserve linearity across the temperature and load range.
সুপারিশকৃত
Automotive Signal Conditioning
The LM2904 family is specified for the extended ambient temperature ranges typical of automotive and harsh-environment electronics, and the 26 V single-supply rating tolerates automotive 12 V rails with load-dump headroom when paired with upstream protection. Ground-sensing inputs simplify ground-referenced sensor interfaces such as coolant-level, oil-pressure, and simple resistive sender conditioning. The dual channels in one PDIP-8 package support a sensing amplifier plus a filter or buffer per connector. For new automotive designs, TI's LM2904B-Q0-grade family members with AEC-Q100 qualification and improved EMI robustness may be preferred; the LM2904VN remains common in legacy and industrial-adjacent vehicle subsystem builds.
সুপারিশকৃত
সুপারিশকৃত পণ্যের সারসংক্ষেপ
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা LM2904VN — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | LM2904NG | LM2904B | LM2904N | LM358N |
|---|---|---|---|---|---|
| Package | PDIP-8 (7.62 mm) | PDIP-8 - same | PDIP-8 - same | PDIP-8 - same | PDIP-8 - same |
| Brand | onsemi | onsemi | Texas Instruments | Texas Instruments | Texas Instruments |
| Number of Circuits | 2 | 2 | 2 | 2 | 2 |
| Gain Bandwidth Product | 1 MHz | 1 MHz | 1 MHz (improved) | 1 MHz | 1 MHz |
| Supply Voltage Range | 3 V to 26 V (32 V total) | 3 V to 26 V (32 V total) | 3 V to 26 V (32 V total) | 3 V to 26 V (32 V total) | 3 V to 26 V (32 V total) |
| Common-Mode Input Range | Extends to ground / VEE | Extends to ground / VEE | Extends to ground / VEE | Extends to ground / VEE | Extends to ground / VEE |
| Mounting Type | Through Hole | Through Hole | Through Hole | Through Hole | Through Hole |
মূল পার্থক্যসমূহ
- Same-brand continuity for existing onsemi BOMs (বনামLM2904N (Texas Instruments))
- Standard offset performance at commodity pricing (বনামLM2904B (Texas Instruments))
- Extended temperature operation vs commercial LM358 (বনামLM358N (Texas Instruments))
ডিজাইন নোট
The LM2904VN output stage is not rail-to-rail: it sources well toward VCC under light load but sinks poorly near ground, so a lightly loaded output may sit 0.6 V to 1 V above VEE. The standard remedy from the manufacturer datasheet application sections is a resistor (typically 2 kOhm) from the output to VEE/GND when signals near the negative rail are required. Also avoid interpreting the device as a precision op-amp - offset voltage is in the millivolt class, and precision transducer front ends should scale down gain-stage error or select a lower-offset pin-compatible alternative such as the TI LM2904B.
In the PDIP-8 through-hole package, place a 100 nF ceramic decoupling capacitor directly across pins 8 (VCC) and 4 (GND/V-) with the shortest possible lead length; on prototyping boards, mount the capacitor on the IC socket side nearest the device. Because the two amplifiers share one die, keep high-gain channel A trace routing away from channel B output traces to prevent inter-channel coupling at high closed-loop gains. For hand-soldered prototypes the 7.62 mm row spacing fits standard grid boards and DIP sockets without lead forming.
The LM2904VN accepts a 3 V to 26 V single supply (32 V total), which comfortably covers automotive 12 V rails with headroom and unregulated industrial supplies. However, check power dissipation when both channels drive moderate loads: dissipation is roughly (VCC - VOUT) x IOUT summed across channels. At 24 V supply driving both outputs to mid-rail into 10 kOhm loads, dissipation stays in the tens of milliwatts - the PDIP package handles this without heatsinking - but low-impedance loads (below 1 kOhm) at high supply voltages should be verified against the datasheet absolute maximum ratings.
As a unity-gain-stable, internally compensated amplifier with 1 MHz GBW and 0.6 V/us slew rate, the LM2904VN is forgiving but not fast. Keep closed-loop bandwidth expectations realistic: gain of 100 limits bandwidth to roughly 10 kHz, and large-signal outputs above 50 kHz will slew-limit. Input bias current of about 45 nA means feedback resistors up to the 100 kOhm range add only a few millivolts of error, but megohm-level networks will bias-current-dominate the error budget - scale resistor values down or choose a JFET/CMOS-input amplifier for those designs.
কমপ্লায়েন্স তথ্য
Compliance details for the LM2904VN suffix must be confirmed on the current onsemi product page; suffix variants within the LM2904 family denote different compliance and packaging grades.