onsemi

LM2904VN - Dual Op Amp, 1MHz GBW, PDIP-8 | onsemi

Référence : LM2904VN ✓ Actif
3 V to 26 V Vdss 45 nA Id 8-PDIP (0.300 in, 7.62 mm) Package
MOQ : 1 |

LM2904VN Présentation

The onsemi LM2904VN is a single-supply dual operational amplifier featuring two independent general-purpose op-amp circuits with a 1 MHz gain-bandwidth product, a 0.6 V/us slew rate, and operation from a 3 V to 26 V supply (up to 32 V total, or +/-1.5 V to +/-16 V split supplies), housed in an 8-pin PDIP (0.300 inch, 7.62 mm) through-hole package.

A dual operational amplifier integrates two matched, frequency-compensated op-amp cores on a single silicon die within one package. As a subcategory of the linear amplifier family, general-purpose op-amps sit within the broader hierarchy of voltage amplifiers and analog signal-conditioning ICs, providing gain, buffering, filtering, and comparison functions in analog front ends. The dual configuration halves board space and improves channel-to-channel matching compared with two single op-amps.

Key features include low power drain, a common-mode input voltage range that extends to ground/VEE (input common-mode includes the negative rail), and single-supply or split-supply operation. These characteristics let designers build ground-referenced signal conditioning directly from a single positive rail without a negative supply, which is the defining advantage of the LM358/LM2904 amplifier family.

Technically, the LM2904VN derives from the circuit design perfected for the industry-standard LM324 quad op-amp: the LM358 series is equivalent to one-half of an LM324. The amplifier delivers approximately 70 dB of open-loop gain, low input bias current (about 45 nA typical per distributor characterization data), and internal frequency compensation that guarantees unity-gain stability without external components.

Typical applications include transducer amplifiers, DC gain blocks, active filters, comparators, and general low-frequency signal conditioning in industrial controls, automotive subsystems, and battery-powered instruments.

A key design consideration: the output stage is not rail-to-rail and can sink only limited current near ground, so loading the output with a resistor to VEE (for example, 2 kOhm) improves output swing close to the negative rail.

This page adds value beyond the manufacturer datasheet by consolidating drop-in cross-references, a parameter comparison table against pin-compatible alternatives, and practical design notes in one place.

Alternatives de remplacement direct pour LM2904VN — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.

Variantes de cette série

Modèles de la même série directement compatibles avec LM2904VN (même facteur de forme et même empreinte) — différant par Package, Mounting Type, Slew Rate, Amplifier Type, Frequency Compensation.

Texas Instruments
Package: SOIC-8 (D)
Mounting Type: Surface Mount
Slew Rate: 0.5 V/us (typical)
Comparer avec LM2904VN →
Texas Instruments
Package: 8-pin PDIP
Mounting Type: Through-hole
Comparer avec LM2904VN →
onsemi
Slew Rate: 0.6 V/µs
Amplifier Type: General Purpose
Frequency Compensation: Internal
Comparer avec LM2904VN →
Texas Instruments
Package: 8-pin mini-DIP or 8-pin PDIP, depending on manufacturer source
Mounting Type: Through-hole
Frequency Compensation: Internally frequency compensated
Comparer avec LM2904VN →

LM2904NG

✅ Remplacement direct
onsemi
📦 PDIP-8
General Purpose · 2 · 1 MHz · 0.6 V/µs · 3 V to 26 V · -40C to +105C · PDIP-8 (0.300 in, 7.62 mm) · Through Hole

Contactez-nous pour le prix

Voir la fiche technique →

LM2904BIDR

✅ Remplacement direct
Texas Instruments
📦 PDIP-8
Texas Instruments · Industry-standard dual operational amplifier · 2 (Dual) · 3 V to 36 V · +/-1.5 V to +/-18 V · 1.2 MHz · 0.5 V/us (typical) · 0.5 mV typical / 3 mV maximum

Contactez-nous pour le prix

Voir la fiche technique →

LM2904N

✅ Remplacement direct
Texas Instruments
📦 PDIP-8
2 amplifiers · 26 V · 1 MHz · Dual independent operational amplifiers · Internally frequency compensated · Single supply or split supply · Extending to ground/VEE

Contactez-nous pour le prix

Voir la fiche technique →

LM358N

✅ Remplacement direct
Texas Instruments
📦 PDIP-8
Dual operational amplifier · 2 independent amplifiers · 32 V · 1 MHz · Differential input · Internally frequency compensated · Single supply operation emphasized in the verified LM358 family description · 8-pin mini-DIP or 8-pin PDIP, depending on manufacturer source

Contactez-nous pour le prix

Voir la fiche technique →

LM2904VN Valeurs maximales et caractéristiques électriques

Amplifier Type General Purpose / Instrumentation, Op Amp, Buffer
Number of Circuits 2
Gain Bandwidth Product 1 MHz
Slew Rate 0.6 V/us
Supply Voltage Range (Single) 3 V to 26 V
Supply Voltage Range (Total) 3 V to 32 V
Supply Voltage Range (Split) +/-1.5 V to +/-16 V
Input Bias Current 45 nA
Open Loop Gain 70 dB
Common Mode Input Range Extends to ground / VEE
Supply Operation Single supply or split supply
Boîtier 8-PDIP (0.300 in, 7.62 mm)
Type de montage Through Hole
Power Drain Low power drain (per manufacturer description)

Configuration des broches de LM2904VN

DIP-8 Package Pinout Diagram DIP-8 8-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 8 2 7 3 6 4 5 DIP-8
Broche 1 OUT A — Output of amplifier A
Broche 2 IN A- — Inverting input of amplifier A
Broche 3 IN A+ — Non-inverting input of amplifier A
Broche 4 GND / V- — Ground or negative supply
Broche 5 IN B+ — Non-inverting input of amplifier B
Broche 6 IN B- — Inverting input of amplifier B
Broche 7 OUT B — Output of amplifier B
Broche 8 VCC / V+ — Positive supply

Applications typiques

LM2904VN convient pour 6 applications: Transducer Amplification, DC Gain Blocks, Active Filters, Comparator Functions, Battery-Powered and Portable Instruments, Automotive Signal Conditioning.

🏭

Transducer Amplification

The LM2904VN is a classic choice for amplifying low-level signals from transducers such as thermistors, strain-gauge bridges, and photodiodes in single-supply industrial equipment. Because its common-mode input range extends to ground/VEE, sensors referenced to 0 V can be connected directly to the non-inverting input without level shifting or a negative rail, at supply voltages from 3 V up to 26 V. Typical gain configurations of 10x to 100x remain well within the 1 MHz gain-bandwidth product, delivering usable closed-loop bandwidth from roughly 10 kHz down to 1 kHz, which is ample for thermal and mechanical process variables. The second amplifier channel in the same PDIP-8 package is commonly used for filtering or output scaling, saving board space and improving channel matching.

⚡

DC Gain Blocks

As a DC gain block, the LM2904VN provides stable non-inverting or inverting gain for scaling sensor outputs, reference levels, and control-loop feedback signals. With approximately 70 dB of open-loop gain, a closed-loop gain of 100 (40 dB) retains about 30 dB of loop gain, keeping gain error and distortion low at DC and low frequencies. The device operates from a single 3 V to 26 V supply or +/-16 V split rails, so the same circuit scales from battery products to industrial 24 V systems. Internal frequency compensation guarantees unity-gain stability with no external capacitor, simplifying BOM. Designers should note the limited output sink near ground and add a pull-down resistor to VEE when output levels close to the negative rail are required.

🔧

Active Filters

The LM2904VN implements Sallen-Key and multiple-feedback active filters in the audio and low-frequency instrumentation range. With a 1 MHz gain-bandwidth product, filter corner frequencies up to roughly 10 kHz at unity-gain Sallen-Key topologies are achievable with minimal Q degradation, and multi-stage anti-alias filters for modest ADC sampling rates fit comfortably. Single-supply operation with inputs valid to ground/VEE allows mid-supply biasing with simple resistor dividers, avoiding negative rails entirely. The dual channels permit a two-pole filter section per PDIP-8 package. The 0.6 V/us slew rate supports full-scale sinusoids up to roughly 95 kHz, so designers should verify slew headroom for large-signal high-frequency filter outputs.

🎥

Comparator Functions

Although dedicated comparators are faster, the LM2904VN is widely used as a low-speed comparator for threshold detection, over-voltage flags, and window monitors where response times of tens of microseconds are acceptable. The input common-mode range extending to ground/VEE enables ground-referenced threshold sensing directly from a single rail, and the wide 3 V to 26 V supply range matches unregulated industrial supplies. Open-loop gain of about 70 dB yields sharp switching thresholds, while the 0.6 V/us slew rate sets propagation delay expectations in the 10 us-class region. Designers should add hysteresis with positive feedback and avoid driving capacitive loads directly to prevent oscillation through slow output transitions.

📱

Battery-Powered and Portable Instruments

The low power drain of the LM2904VN family makes it suitable for battery-operated measurement and monitoring products operating from 3 V upward. A single PDIP-8 package supplies two amplifier channels for front-end gain and active filtering while drawing minimal quiescent current relative to the system budget, and operation down to 3 V total supply accommodates two-cell or single-cell-boosted architectures. The through-hole PDIP package also simplifies prototyping, rework, and educational instrument builds. For battery designs, note that the output stage cannot swing fully to the rails, so define signal ranges with 1 V-class headroom from either rail to preserve linearity across the temperature and load range.

🚗

Automotive Signal Conditioning

The LM2904 family is specified for the extended ambient temperature ranges typical of automotive and harsh-environment electronics, and the 26 V single-supply rating tolerates automotive 12 V rails with load-dump headroom when paired with upstream protection. Ground-sensing inputs simplify ground-referenced sensor interfaces such as coolant-level, oil-pressure, and simple resistive sender conditioning. The dual channels in one PDIP-8 package support a sensing amplifier plus a filter or buffer per connector. For new automotive designs, TI's LM2904B-Q0-grade family members with AEC-Q100 qualification and improved EMI robustness may be preferred; the LM2904VN remains common in legacy and industrial-adjacent vehicle subsystem builds.

What is the LM2904VN?
The LM2904VN is an onsemi single-supply dual operational amplifier in an 8-pin PDIP through-hole package. It integrates two independent, internally frequency-compensated op-amps with a 1 MHz gain-bandwidth product and 0.6 V/us slew rate, and operates from 3 V to 26 V single supply (3 V to 32 V total, or +/-1.5 V to +/-16 V split). Its common-mode input range extends to ground/VEE, which is the hallmark of the LM358/LM2904 family.
What is the supply voltage range of the LM2904VN?
The LM2904VN operates from 3 V to 26 V on a single supply, corresponding to 3 V to 32 V total supply across both rails. In split-supply operation it accepts +/-1.5 V to +/-16 V. According to the onsemi datasheet description reproduced by distributor listings, the device also supports low-power drain across this range, making it usable in both industrial 24 V systems and low-voltage portable designs.
What is the gain bandwidth product of the LM2904VN?
The LM2904VN has a 1 MHz gain-bandwidth product and a 0.6 V/us slew rate, per distributor characterization of the device. In practice this means the amplifier is well suited to audio-band and low-frequency industrial signal conditioning - for example, a closed-loop gain of 10 gives roughly 100 kHz of usable bandwidth. For higher-speed designs, choose a faster pin-compatible op-amp instead.
What is the difference between LM2904VN and LM2904NG?
Both are onsemi LM2904-family dual op-amps in 8-pin PDIP packages and are essentially interchangeable, but the suffixes denote different compliance or packaging grades rather than different silicon performance. Both share the standard LM358 pinout (OUT A, IN A-, IN A+, GND, IN B+, IN B-, OUT B, VCC) and the same 1 MHz GBW-class performance, so either can replace the other on the same PCB footprint. Check the current onsemi datasheet suffix table for the exact qualification difference.
What is the difference between LM2904VN and LM2904B?
The Texas Instruments LM2904B is a pin-to-pin upgrade of the standard LM2904 with improved performance - notably lower offset voltage and offset drift - in the same package and pinout. TI's own product comparison page positions LM2904B as a pin-to-pin upgrade with improved performance and lower 1ku price versus LM2904. The LM2904VN offers the same footprint and function, so LM2904B can be a drop-in upgrade when tighter accuracy is required, though it is a cross-brand (TI) part.
What is the best drop-in replacement for LM2904VN?
The best drop-in replacements are parts that share the standard LM358/LM2904 dual-op-amp pinout in an 8-pin PDIP package: onsemi LM2904NG (same brand), Texas Instruments LM2904N and the improved LM2904B, and the industry-standard TI LM358N. All are pin-to-pin compatible with identical supply ranges in the 32 V class. For new designs needing better precision, LM2904B is recommended; for exact form-fit-function continuity, the same-brand LM2904NG is the safest choice.
Can LM358N replace LM2904VN?
Yes - the LM358N is pin-compatible with the LM2904VN in the 8-pin PDIP package and is electrically equivalent for most general-purpose uses. The LM2904 is essentially the industrial/automotive-temperature sibling of the commercial LM358 family; per onsemi, the LM358 series is equivalent to one-half of an LM324, and the cross-reference guides group LM2904 with LM358 as compatible equivalents. Verify the operating temperature range requirement before substitution: LM2904 parts are specified for wider ambient ranges than commercial LM358 grades.
Where can I download the LM2904VN datasheet PDF?
The LM2904VN datasheet PDF is published by onsemi and is available through the datasheet link on this page, hosted at alldatasheet.com (14-page document, ON Semiconductor, titled Single Supply Dual Operational Amplifiers). The datasheet contains the full electrical characteristics table, the 8-pin PDIP pinout diagram, application circuits, and absolute maximum ratings needed for design-in.
Where can I find the LM2904VN pinout?
The LM2904VN uses the industry-standard dual op-amp pinout in the 8-pin PDIP: pin 1 is output A, pin 2 is inverting input A, pin 3 is non-inverting input A, pin 4 is GND/V-, pin 5 is non-inverting input B, pin 6 is inverting input B, pin 7 is output B, and pin 8 is VCC/V+. The pin diagram in this page follows the manufacturer datasheet numbering, and the full pin-description table is in the onsemi datasheet.
Is LM2904VN suitable for single-supply operation?
Yes - single-supply operation is the core design intent of the LM2904VN. The common-mode input voltage range extends to ground/VEE, meaning inputs can be referenced directly to the negative rail, and the amplifier works from a single 3 V to 26 V supply. This eliminates the need for a negative rail in transducer amplifiers, DC gain blocks, and comparator-style circuits, which is why the family is ubiquitous in single-rail industrial and automotive electronics.
What are the key specifications of LM2904VN that engineers should know?
Engineers should know five key LM2904VN specifications: two op-amp circuits per package; 1 MHz gain-bandwidth product with 0.6 V/us slew rate; supply range of 3 V to 26 V single-supply (3 V to 32 V total, +/-1.5 V to +/-16 V split); common-mode input range extending to ground/VEE; and approximately 70 dB open-loop gain with about 45 nA input bias current. The package is 8-pin PDIP (7.62 mm row spacing) through-hole.
What is the price of LM2904VN and where can I buy it online?
LM2904VN is a low-cost, widely stocked dual op-amp available from multiple authorized channels. For current unit pricing at each quantity break, stock status, and lead time, use the Request a Quote form on this page - pricing is computed live from channel listings and changes daily, so a static figure on the page would be unreliable. The part is packaged in tubes for through-hole PDIP assembly.
Is LM2904VN in stock and what is the lead time?
The LM2904VN is an active, high-volume commodity part carried by numerous authorized distributors, so stock availability is generally good. Real-time stock and lead time for your required quantity are provided through the Request a Quote form on this page. If through-hole PDIP is not mandatory, surface-mount LM2904 variants in SOIC-8 offer broader stocking and lower cost per unit.
When should I choose LM2904VN over the TI LM2904B?
Choose the LM2904VN when you need exact continuity with an existing onsemi-sourced bill of materials, when the 1 MHz-class bandwidth and standard offset performance are sufficient, or when through-hole PDIP prototyping and hand-soldering convenience matter most. Choose the TI LM2904B when offset voltage, offset drift, or EMI robustness are design-limiting, since it is a pin-to-pin performance upgrade in the same package. Both operate over the same supply range, so switching costs only a component change, not a PCB revision.
What is the best TI equivalent for the LM2904VN?
The best Texas Instruments equivalents for the LM2904VN are the LM2904N (same-generation pin-compatible dual op-amp in PDIP-8) and the LM2904B (pin-to-pin upgrade with lower offset and drift, per TI's own comparison page). For commercial-temperature designs, the LM358N is also pin-compatible and electrically equivalent. All three accept the same 3 V to 32 V-class supplies and share the LM358 pinout, making them true drop-in alternatives on the same PCB footprint.

Données de référence d'ingénierie pour LM2904VN — comparaison, recommandations de conception et informations de conformité.

Guide de sélection

Choose the onsemi LM2904VN when you need a proven single-supply dual op-amp in through-hole PDIP-8 for prototyping, repair, or industrial signal conditioning with ground-sensing inputs, and your accuracy budget tolerates millivolt-class offset. Choose the same-brand LM2904NG when onsemi sourcing continuity matters or the required compliance grade differs. Choose the TI LM2904B when offset voltage, offset drift, or EMI robustness are design-limiting - it is a pin-to-pin performance upgrade on the same footprint, so the PCB does not change. Choose the TI LM2904N when cross-brand second sourcing of the standard LM2904 grade is the goal. Choose the LM358N only for commercial-temperature products, since its ambient range is narrower than the LM2904 family's. All five parts share the identical LM358 pinout and 3 V to 32 V-class supply range, so selection is driven by temperature grade, precision, and sourcing rather than footprint.

Comparaison avec les alternatives

Paramètre Ce produit LM2904NG LM2904B LM2904N LM358N
Package PDIP-8 (7.62 mm) PDIP-8 - same PDIP-8 - same PDIP-8 - same PDIP-8 - same
Brand onsemi onsemi Texas Instruments Texas Instruments Texas Instruments
Number of Circuits 2 2 2 2 2
Gain Bandwidth Product 1 MHz 1 MHz 1 MHz (improved) 1 MHz 1 MHz
Supply Voltage Range 3 V to 26 V (32 V total) 3 V to 26 V (32 V total) 3 V to 26 V (32 V total) 3 V to 26 V (32 V total) 3 V to 26 V (32 V total)
Common-Mode Input Range Extends to ground / VEE Extends to ground / VEE Extends to ground / VEE Extends to ground / VEE Extends to ground / VEE
Mounting Type Through Hole Through Hole Through Hole Through Hole Through Hole

Principaux différenciateurs

  • Same-brand continuity for existing onsemi BOMs (vs LM2904N (Texas Instruments))
  • Standard offset performance at commodity pricing (vs LM2904B (Texas Instruments))
  • Extended temperature operation vs commercial LM358 (vs LM358N (Texas Instruments))

Notes de conception

The LM2904VN output stage is not rail-to-rail: it sources well toward VCC under light load but sinks poorly near ground, so a lightly loaded output may sit 0.6 V to 1 V above VEE. The standard remedy from the manufacturer datasheet application sections is a resistor (typically 2 kOhm) from the output to VEE/GND when signals near the negative rail are required. Also avoid interpreting the device as a precision op-amp - offset voltage is in the millivolt class, and precision transducer front ends should scale down gain-stage error or select a lower-offset pin-compatible alternative such as the TI LM2904B.

In the PDIP-8 through-hole package, place a 100 nF ceramic decoupling capacitor directly across pins 8 (VCC) and 4 (GND/V-) with the shortest possible lead length; on prototyping boards, mount the capacitor on the IC socket side nearest the device. Because the two amplifiers share one die, keep high-gain channel A trace routing away from channel B output traces to prevent inter-channel coupling at high closed-loop gains. For hand-soldered prototypes the 7.62 mm row spacing fits standard grid boards and DIP sockets without lead forming.

The LM2904VN accepts a 3 V to 26 V single supply (32 V total), which comfortably covers automotive 12 V rails with headroom and unregulated industrial supplies. However, check power dissipation when both channels drive moderate loads: dissipation is roughly (VCC - VOUT) x IOUT summed across channels. At 24 V supply driving both outputs to mid-rail into 10 kOhm loads, dissipation stays in the tens of milliwatts - the PDIP package handles this without heatsinking - but low-impedance loads (below 1 kOhm) at high supply voltages should be verified against the datasheet absolute maximum ratings.

As a unity-gain-stable, internally compensated amplifier with 1 MHz GBW and 0.6 V/us slew rate, the LM2904VN is forgiving but not fast. Keep closed-loop bandwidth expectations realistic: gain of 100 limits bandwidth to roughly 10 kHz, and large-signal outputs above 50 kHz will slew-limit. Input bias current of about 45 nA means feedback resistors up to the 100 kOhm range add only a few millivolts of error, but megohm-level networks will bias-current-dominate the error budget - scale resistor values down or choose a JFET/CMOS-input amplifier for those designs.

Informations de conformité

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Sans plomb
Unknown
Sans halogène
Unknown
Minerais de conflit
Unknown

Compliance details for the LM2904VN suffix must be confirmed on the current onsemi product page; suffix variants within the LM2904 family denote different compliance and packaging grades.

Données vérifiées le : 2026-11-08 — données vérifiées et sélectionnées par l'équipe d'ingénierie composants de XAIPART

Recherches associées

LM2904VN datasheet LM2904VN datasheet pdf LM2904VN pinout LM2904VN equivalent LM2904VN replacement LM2904VN vs LM2904NG LM2904VN vs LM2904B onsemi LM2904VN LM2904VN price LM2904VN stock LM2904 dual op amp single supply LM2904 application circuit

Composants & termes associés

onsemi LM2904VN LM2904NG LM2904B LM2904N LM358N operational amplifier dual op-amp linear amplifier analog signal conditioning IC PDIP-8 DIP package family through-hole mounting gain-bandwidth product slew rate single-supply operation common-mode input range RoHS transducer amplifier active filter
RFQ de devis rapide
Renseignez tous les détails — notre équipe commerciale vous répondra sous 24 heures
Référence Fabricant Boîtier QTY Prix cible Total
✓
Devis envoyé !

Nous répondrons à votre e-mail sous 24 heures

1
RFQ envoyée
2
Devis reçu
3
Commande passée
4
Paiement
5
Expédié
6
Livré
Voir les détails de la RFQ