NXP Semiconductors

LPC1114FHN33/333 - 50MHz Arm Cortex-M0 MCU | NXP

MPN: LPC1114FHN33/333 ✓ সক্রিয়
1.8 V to 3.6 V Vdss 32-HVQFN, 7 mm x 7 mm Package 50 MHz Speed 32 KB Memory
সর্বনিম্ন অর্ডার পরিমাণ: 1 |

LPC1114FHN33/333 সারাংশ

The NXP LPC1114FHN33/333 is a 32-bit Arm Cortex-M0 microcontroller operating at up to 50 MHz, with 32 KB of flash memory and 8 KB of SRAM in a 32-HVQFN 7 x 7 mm package. The device operates from 1.8 V to 3.6 V with a nominal 3.3 V supply, providing 28 general-purpose I/O lines for compact embedded-control designs.

A microcontroller is a programmable semiconductor that integrates a processor core, memory, peripherals, and I/O into one device. The LPC1114FHN33/333 belongs to the LPC11xx family, where Cortex-M0 processors provide low-cost 32-bit control with a reduced instruction set and compact code footprint. This hierarchy connects the LPC1114FHN33/333 to Arm Cortex-M0 microcontrollers, 32-bit embedded MCUs, and general-purpose embedded semiconductors.

Key device features include 50 MHz CPU operation, 32 KB of flash for program storage, 8 KB of SRAM for working memory, and a 1.8 V to 3.6 V operating range. The 32-HVQFN package supports dense PCB layouts while providing 28 GPIO lines. Arm Keil identifies the LPC1100 series as a CMSIS-pack-supported family designed for 8-bit and 16-bit controller upgrades, metering, lighting, and alarm-system applications.

The LPC1114FHN33/333 combines an Arm Cortex-M0 RISC core with on-chip Flash and SRAM to support compact firmware without an external memory interface. Its 3.3 V-centered operating range suits conventional industrial, consumer, metering, lighting-control, and alarm-system rails. Designers must observe the package-specific exposed-pad layout and provide the recommended decoupling and thermal-via arrangement when laying out the HVQFN footprint.

Typical applications include smart energy meters, LED lighting controllers, alarm and security panels, compact sensor nodes, industrial control modules, and low-cost HMI controllers. In each case, the 50 MHz core provides useful peripheral-processing headroom, while 32 KB of flash and 8 KB of SRAM allow local code and state to remain on the MCU rather than requiring external memory.

For robust implementation, place the supply bypass capacitor close to the power pins and connect the exposed thermal pad to a properly sized copper area with thermal vias. Confirm every signal's pin assignment against the manufacturer's package pin table before PCB release, and validate firmware, clock, reset, and low-power behavior across the complete 1.8 V to 3.6 V supply range.

This page consolidates lifecycle information, package characteristics, drop-in alternatives, comparison parameters, and practical design guidance for engineers evaluating the LPC1114FHN33/333. It also distinguishes electrically similar LPC1114 variants so engineers can identify the closest package-compatible options without confusing order codes or functional differences.

এর জন্য ড্রপ-ইন বিকল্প LPC1114FHN33/333 — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।

এই সিরিজের ভ্যারিয়েন্ট

একই সিরিজের মডেল যেগুলো drop-in compatible LPC1114FHN33/333 (একই form factor এবং footprint) — পার্থক্য রয়েছে Lifecycle Status, Package.

NXP Semiconductors
Lifecycle Status: End of Life (per NXP product page)
Package: 24-HVQFN (4x4 mm), Exposed Pad

LPC1114FHN33/302K

✅ ড্রপ-ইন
📦 32-HVQFN (7 x 7 mm)
Same 50 MHz Cortex-M0 architecture, 32 KB flash, 8 KB SRAM, and 32-HVQFN footprint; ordering suffix differs by 0% in listed core parameters.

📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)

LPC1114FHN33/303

✅ ড্রপ-ইন
📦 32-HVQFN (7 x 7 mm)
Same 50 MHz Cortex-M0 architecture, 32 KB flash, 8 KB SRAM, and 32-HVQFN footprint; ordering suffix differs by 0% in listed core parameters.

📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)

LPC1114JHN33/333E

✅ ড্রপ-ইন
📦 32-HVQFN (7 x 7 mm)
Same LPC1114 33-pin package family and 50 MHz Cortex-M0 platform; the J and E order-code attributes differ, with listed core memory and CPU parameters unchanged.

📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)

LPC1114FHN33/303Y

✅ ড্রপ-ইন
📦 32-HVQFN (7 x 7 mm)
Same 50 MHz Cortex-M0 core, 32 KB flash, 8 KB SRAM, and 32-HVQFN footprint; the Y suffix changes an ordering attribute while listed core parameters remain equal.

📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)

LPC1114FHI33

✅ ড্রপ-ইন
📦 32-HVQFN (7 x 7 mm)
Same LPC1114 50 MHz Cortex-M0 family and 32-HVQFN footprint; listed core CPU and memory ratings are unchanged, while the I suffix changes the order-code configuration.

📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)

LPC1114FHN33/333 সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য

Product Type 32-bit Arm Cortex-M0 microcontroller
Maximum CPU Frequency 50 MHz
Flash Memory 32 KB
SRAM 8 KB
অপারেটিং সাপ্লাই ভোল্টেজ 1.8 V to 3.6 V
Nominal Supply Voltage 3.3 V
General-Purpose I/O 28 lines
Architecture Arm Cortex-M0 RISC
প্যাকেজ 32-HVQFN, 7 mm x 7 mm
Package Designation PQCC33
মাউন্টিং টাইপ Surface mount
অপারেটিং তাপমাত্রা -40 °C to +85 °C
লাইফসাইকেল স্ট্যাটাস Active

LPC1114FHN33/333 pqcc33 পিন কনফিগারেশন গাইড

LPC1114FHN33/333 (pqcc33 প্যাকেজ)-এর পিন কনফিগারেশন। এই ডিজিটাল IC-তে GPIO, কমিউনিকেশন ইন্টারফেস (UART, SPI, I2C) এবং পাওয়ার পিন রয়েছে। বিকল্প পিন ফাংশন ও কনফিগারেশন অপশনের জন্য প্রস্তুতকারকের ডেটাশিট দেখুন। এমবেডেড সিস্টেম ডিজাইন ও PCB লেআউটের জন্য অপরিহার্য।

LPC1114FHN33/333-এর জন্য pqcc33 প্যাকেজ পিনআউট ডায়াগ্রাম

এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি LPC1114FHN33/333.

দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।

সাধারণ ব্যবহার

LPC1114FHN33/333 এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Smart Energy Metering, LED Lighting Control, Alarm and Security Panels, Industrial Sensor Nodes, Compact HMI Controllers, Low-Cost HMI and Utility Controls.

⚡

Smart Energy Metering

The LPC1114FHN33/333 fits compact metering controllers that collect pulses, process sensor inputs, and maintain operating state without external memory. Its 50 MHz Arm Cortex-M0 core provides processing headroom for measurement routines, while 32 KB of flash accommodates firmware and calibration data and 8 KB of SRAM supports buffers and stack requirements. The 1.8 V to 3.6 V operating range suits regulated 3.3 V metering rails. In a meter design, the 28 GPIO lines can connect pulse inputs, display-control signals, communications, and status indicators. The 32-HVQFN package also reduces board area, although the exposed pad requires a thermal copper pattern and vias. Validate timing-critical pulse capture, low-power behavior, and calibration retention across the intended supply and temperature range.

💡

LED Lighting Control

The LPC1114FHN33/333 can serve as the central controller in an LED lighting module that requires sequencing, dimming, fault monitoring, and local configuration storage. The 50 MHz Cortex-M0 core executes timing and control logic with ample bandwidth relative to simple 8-bit alternatives. Its 28 GPIO lines support LED-control outputs, switch inputs, and status signaling, while 8 KB of SRAM can hold update buffers and 32 KB of flash can retain control tables or firmware. Operation from 1.8 V to 3.6 V permits integration with 3.3 V driver electronics. The 32-HVQFN 7 x 7 mm package is useful for space-constrained lamp modules, but designers should follow the exposed-pad land pattern and place bypass capacitance close to the supply pins to limit switching-related supply disturbance.

🛡️

Alarm and Security Panels

The LPC1114FHN33/333 is appropriate for compact alarm panels that supervise sensors, drive annunciators, and manage keypad or status-indicator interfaces. Its 32-bit Cortex-M0 architecture supports larger state machines than an 8-bit controller while retaining a cost-focused embedded implementation. The 50 MHz operating speed handles periodic sensor scanning and communication tasks, and 8 KB of SRAM is suitable for event buffers and working variables. A 3.3 V nominal rail and 1.8 V to 3.6 V operating range align with many security subsystems. The 28 GPIO lines provide broad panel connectivity, while the 32-HVQFN package helps reduce enclosure size. Critical alarm functions should be tested for startup behavior, input filtering, supply-brownout response, and firmware update recovery before deployment.

🏭

Industrial Sensor Nodes

The LPC1114FHN33/333 works well in a small industrial sensor node that samples switches or analog front ends, applies filtering, and reports measurements through a serial interface. Its 50 MHz Arm Cortex-M0 core provides sufficient throughput for local signal processing, while 32 KB of flash stores application code and 8 KB of SRAM accommodates samples and communication buffers. The 1.8 V to 3.6 V range supports 3.3 V process-control electronics, and 28 GPIO lines simplify sensor multiplexing, status LEDs, and interface connections. The 32-HVQFN footprint supports compact boards, but environmental robustness depends on the complete assembly rather than the MCU alone. Validate input thresholds, clock tolerance, isolation strategy, thermal rise, and transient immunity for the installation environment.

📺

Compact HMI Controllers

The LPC1114FHN33/333 can coordinate a small human-machine interface built around a display, buttons, and status indicators. The 50 MHz Cortex-M0 processor manages refresh tasks and input scanning, while 32 KB of flash holds interface firmware and graphics assets and 8 KB of SRAM supports screen buffers. Twenty-eight GPIO lines can be allocated among display-control signals, capacitive or mechanical inputs, and communications. Its 1.8 V to 3.6 V supply range enables operation from 3.3 V embedded systems, and the 32-HVQFN package reduces board area for behind-panel electronics. Because display and communication peripherals can create sharp current transitions, the design should include local supply decoupling, deliberate signal-return routing, and GPIO drive-level checks based on the selected external interface.

🔧

Low-Cost HMI and Utility Controls

The LPC1114FHN33/333 is a practical control processor for compact utility equipment where a 32-bit CPU, local program memory, and moderate I/O are required in a small board. The 50 MHz core can execute communication stacks and control sequences, while 32 KB of flash and 8 KB of SRAM keep routine firmware resident locally. Its 28 GPIO lines support relays, status inputs, displays, and service interfaces. The nominal 3.3 V operation fits standard embedded rails, and the 1.8 V minimum can simplify matching to 1.8 V peripherals when the complete power tree permits it. The 7 x 7 mm 32-HVQFN package conserves PCB area, but exposed-pad soldering, thermal vias, and ground-return continuity remain essential for reliable industrial operation and electromagnetic compatibility.

সুপারিশকৃত পণ্যের সারসংক্ষেপ

LPC1114FHN33/302K Related 32-HVQFN metering controller ব্যবহৃত হয়: Smart Energy Metering, Alarm and Security Panels LPC1114FHN33/303 Related 32-HVQFN metering controller ব্যবহৃত হয়: Smart Energy Metering, Compact HMI Controllers LPC1114JHN33/333E Related LPC1114 lighting-control MCU ব্যবহৃত হয়: LED Lighting Control, Compact HMI Controllers LPC1114FHI33 Related 32-HVQFN lighting-control MCU ব্যবহৃত হয়: LED Lighting Control, Industrial Sensor Nodes LPC1114FHN33/303Y Related LPC1114 security-panel controller ব্যবহৃত হয়: Alarm and Security Panels, Low-Cost HMI and Utility Controls LPC11E14FHN33 Related low-cost 32-HVQFN embedded controller ব্যবহৃত হয়: Industrial Sensor Nodes, Low-Cost HMI and Utility Controls
Where can I download the LPC1114FHN33/333 datasheet?
The LPC1114FHN33/333 datasheet and product resources are available through NXP's official product page for LPC1114FHN33. According to NXP, the device is active and provides an overview, operating features, environmental-quality information, shipping information, and a data-sheet link. A separate datasheet-index page also provides a direct download path for LPC1114FHN33-333 documentation.
What are the key specifications of LPC1114FHN33/333 that engineers should know?
The LPC1114FHN33/333 combines a 50 MHz Arm Cortex-M0 core, 32 KB of flash memory, 8 KB of SRAM, 28 GPIO lines, and a 1.8 V to 3.6 V supply range in a 32-HVQFN package. NXP identifies the part as active, while the 7 x 7 mm package and nominal 3.3 V operation suit compact embedded-control boards. Its 32-bit architecture provides more addressing capacity than a typical 8-bit controller while retaining a compact software footprint.
What is the operating voltage of LPC1114FHN33/333?
The LPC1114FHN33/333 operates from 1.8 V to 3.6 V, with 3.3 V identified as the nominal supply. The LPC1114FHN33-333 product information reports the same voltage range and describes the device as a CMOS microcontroller. Confirm each rail's tolerance and sequencing requirements in the manufacturer datasheet before designing the power architecture.
Where can I find the LPC1114FHN33/333 pinout?
The LPC1114FHN33/333 pin assignments are shown in the package pin-configuration section of NXP's LPC1114FHN33 documentation. The component uses a 32-HVQFN 7 x 7 mm package identified as PQCC33, with 28 general-purpose I/O lines and an exposed pad that requires proper PCB thermal construction. Use the manufacturer diagram when assigning tracks because exposed-pad and no-connect details must follow the exact ordering code.
How much flash and SRAM does LPC1114FHN33/333 have?
The LPC1114FHN33/333 provides 32 KB of flash memory and 8 KB of SRAM. NXP describes the part as a 32-bit Arm Cortex-M0 MCU with those memory resources, and its operating range is 1.8 V to 3.6 V. The flash stores firmware, while SRAM supports stack, heap, buffers, and other time-sensitive working data during execution.
Is LPC1114FHN33/333 suitable for metering and lighting applications?
Yes, LPC1114FHN33/333 is suitable for compact metering, lighting, alarm, and similar embedded-control systems. Arm Keil lists metering, lighting, and alarm systems among the LPC1100 family's typical applications. Its 50 MHz Cortex-M0 core, 28 GPIO lines, 32 KB of flash, and 8 KB of SRAM provide the processing and I/O capacity needed for low-cost controller upgrades from 8-bit or 16-bit designs.
What can replace LPC1114FHN33/333?
The closest documented package-compatible options are other LPC1114FHN33 order codes, particularly LPC1114FHN33/302K and LPC1114FHN33/303, which retain the 32-HVQFN format and 50 MHz Cortex-M0 architecture. Verify ordering-code, qualification, temperature, and firmware-compatibility differences before substitution. Cross-brand drop-in equivalents are not identified in the available manufacturer and distributor records.
Is LPC1114FHN33/333 the same as LPC1114FHN33/302K?
No. LPC1114FHN33/302K and LPC1114FHN33/333 are related LPC1114 variants in the same general 32-HVQFN family, but their order codes encode different device options. LPC1114FHN33/302K is listed with 32 KB flash, 8 KB SRAM, 50 MHz operation, and a 32-HVQFN package. Confirm the exact suffix meaning, qualification, and lifecycle requirements in NXP documentation before using one as the other.
LPC1114FHN33/333 vs LPC1114FHN33/303: which is better for a new design?
Choose LPC1114FHN33/333 when its documented order-code qualifications and current active status satisfy the project requirements; choose LPC1114FHN33/303 only after confirming its specific temperature or qualification attributes. Both parts are associated with the same LPC1114FHN33 32-HVQFN family and 50 MHz Cortex-M0 architecture. The practical distinction depends on the encoded suffix rather than a change in CPU architecture or package.
When should I choose LPC1114FHN33/333 over another LPC1114 variant?
Choose LPC1114FHN33/333 when the design requires the active LPC1114FHN33 ordering option with 50 MHz operation, 32 KB flash, 8 KB SRAM, 28 GPIO lines, and a 32-HVQFN footprint. Select another LPC1114 order code only when its suffix provides a required qualification, temperature grade, test option, or lifecycle advantage. This prevents an electrically similar part from introducing unintended qualification changes.
Is LPC1114FHN33/333 in stock?
Current stock quantity should be checked through the Request a Quote form on this page because inventory changes rapidly and may vary by package and shipment quantity. The manufacturer lists LPC1114FHN33 as active, which indicates ongoing product support rather than a guaranteed allocation at every distributor. Submit the required quantity, target date, and delivery location with your quote request.
What is the price of LPC1114FHN33/333?
Use the Request a Quote form on this page for a current LPC1114FHN33/333 quotation and quantity availability. Pricing depends on order quantity, lead time, packaging requirements, and market conditions, so a static figure can become inaccurate. The form is the appropriate route for checking the exact MPN, including the /333 suffix and 32-HVQFN delivery configuration.
What is the lead time for LPC1114FHN33/333?
Request the current lead time through the Request a Quote form on this page and include your required quantity, target date, and ship-to region. NXP lists LPC1114FHN33 as active, but lifecycle status does not by itself guarantee a fixed lead time or inventory quantity. The quote process can account for standard stock, scheduled production, and any lot-specific planning requirements.
What development tools support LPC1114FHN33/333?
The LPC1114FHN33/333 is associated with the LPC1100 series and its CMSIS device-family pack in Arm Keil. Arm Keil describes the family as supporting low-cost 8-bit and 16-bit microcontroller upgrades and lists metering, lighting, and alarm systems as typical uses. Use the matching LPC1100 device-family pack to access the peripheral definitions and device parameters needed during compilation and debugging.
Is there a cross-brand equivalent for LPC1114FHN33/333?
No verified cross-brand drop-in equivalent is identified for LPC1114FHN33/333 in the available records. A direct replacement should use the same 32-HVQFN footprint, 1.8 V to 3.6 V supply range, compatible memory arrangement, and matching peripheral pin functions. NXP LPC1114 order-code variants are the more defensible starting points, while any cross-brand device requires schematic and firmware verification before substitution.

এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা LPC1114FHN33/333 — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।

নির্বাচন গাইড

Choose LPC1114FHN33/333 for a new design that needs the active LPC1114FHN33 ordering configuration, a 50 MHz Arm Cortex-M0 core, 32 KB of flash, 8 KB of SRAM, 28 GPIO lines, and a 32-HVQFN footprint. LPC1114FHN33/302K and LPC1114FHN33/303 are package-compatible choices when their specific suffix attributes better match sourcing, qualification, or production requirements. Consider LPC1114JHN33/333E only after checking its J and E attributes against the target ordering code, and evaluate LPC1114FHN33/303Y or LPC1114FHI33 for their suffix-specific benefits. No verified cross-brand drop-in option is established, so changing manufacturers would require a complete pin-function, timing, peripheral, toolchain, and firmware review rather than a simple footprint substitution.

বিকল্পের সাথে তুলনা

পারামিটার এই পণ্য LPC1114FHN33/302K LPC1114FHN33/303 LPC1114JHN33/333E LPC1114FHN33/303Y LPC1114FHI33
Brand NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors
Package 32-HVQFN (7 x 7 mm) 32-HVQFN (7 x 7 mm) - same package 32-HVQFN (7 x 7 mm) - same package 32-HVQFN (7 x 7 mm) - same package 32-HVQFN (7 x 7 mm) - same package 32-HVQFN (7 x 7 mm) - same package
CPU Core Arm Cortex-M0 Arm Cortex-M0 Arm Cortex-M0 Arm Cortex-M0 Arm Cortex-M0 Arm Cortex-M0
Maximum CPU Frequency 50 MHz 50 MHz 50 MHz 50 MHz 50 MHz 50 MHz
Special Ordering Attributes /333 order-code configuration /302K order-code configuration /303 order-code configuration J and E suffix attributes Y suffix attribute I suffix attribute

মূল পার্থক্যসমূহ

  • Maintains the full LPC1114 core specification set (বনামLPC1114FHN33/302K)
  • Matches the established 32-HVQFN 7 x 7 mm footprint (বনামLPC1114JHN33/333E)
  • Provides 28 GPIO lines for compact control systems (বনামLPC1114FHN33/303Y)

ডিজাইন নোট

Treat the exposed pad as both a thermal and electrical land feature. Follow the manufacturer's PQCC33 land pattern, place thermal vias within or near the pad where the recommended layout permits, and connect the pad to the ground plane. Do not substitute the exposed pad for a normal perimeter pin in the schematic or PCB library.

Place the local supply bypass capacitor immediately beside the MCU power and ground pins, with a short, low-inductance return path. The device operates from 1.8 V to 3.6 V, so verify startup, brownout, and steady-state behavior at the actual rail voltage rather than assuming a nominal 3.3 V supply alone is sufficient.

Assign GPIO and clock nets directly from the manufacturer pin table, especially when using an HVQFN footprint with an exposed pad. Check alternate-function, debug, reset, and no-connect requirements before routing. For externally connected signals, include appropriate protection and ensure that any external pull network complements the MCU's configurable internal pull resistors.

কমপ্লায়েন্স তথ্য

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
লিড ফ্রি
Unknown
হ্যালোজেন ফ্রি
Unknown
কনফ্লিক্ট মিনারেলস
Unknown

The manufacturer identifies the LPC1114FHN33 as active, but no explicit environmental or material-compliance declaration was present in the cited product snippets. Confirm RoHS, REACH, lead-free, halogen-free, conflict-minerals, and automotive-qualification status in the current manufacturer documentation.

ডেটা যাচাই করা হয়েছে: 2026-11-20 — ডেটা XAIPART-এর কম্পোনেন্ট ইঞ্জিনিয়ারিং টিম দ্বারা যাচাই ও কিউরেট করা হয়েছে

সম্পর্কিত অনুসন্ধান

LPC1114FHN33/333 datasheet LPC1114FHN33/333 specifications LPC1114FHN33 datasheet pdf LPC1114FHN33/333 pinout LPC1114FHN33 equivalent LPC1114FHN33/333 replacement LPC1114FHN33 cross reference LPC1114FHN33/333 vs LPC1114FHN33/302K LPC1114FHN33 HVQFN32 footprint NXP LPC1114FHN33/333 LPC1114FHN33/333 price LPC1114FHN33/333 stock

সম্পর্কিত কম্পোনেন্ট ও শর্তাবলী

NXP Semiconductors LPC1114FHN33/333 LPC1114FHN33 LPC1114FHN33/302K LPC1114FHN33/303 LPC1114JHN33/333E LPC1114FHN33/303Y LPC1114FHI33 LPC11E14FHN33 Arm Cortex-M0 Arm Cortex-M0+ LPC1100 series LPC1100XL 32-bit microcontroller embedded microcontroller semiconductor 32-HVQFN PQCC33 QFN family surface mount flash memory SRAM GPIO CMSIS Arm Keil
তাৎক্ষণিক বিলওয়াছে রেকোজিউইট
সম্পূর্ণ বিবরণ পূরণ করুন — আমাদের সেলস টিম 24 ঘণ্টার মধ্যে উত্তর দেবে
পার্ট নম্বর উৎপাদক প্যাকেজ QTY লক্ষ্যমূল্য প্রসারিত
✓
বিল প্রস্তুত করা হয়েছে!

আমরা ২৪ ঘণ্টার মধ্যে আপনার ইমেইলে প্রত্যুত্তর দেব

1
RFQ জমা হয়েছে
2
কোটেশন পাওয়া গেছে
3
অর্ডার দেওয়া হয়েছে
4
পেমেন্ট
5
শিপ করা হয়েছে
6
ডেলিভারি হয়েছে
RFQ বিবরণ দেখুন