LPC1114FHN33/333 - 50MHz Arm Cortex-M0 MCU | NXP
部品番号: LPC1114FHN33/333 ✓ 生産中LPC1114FHN33/333 概要
A microcontroller is a programmable semiconductor that integrates a processor core, memory, peripherals, and I/O into one device. The LPC1114FHN33/333 belongs to the LPC11xx family, where Cortex-M0 processors provide low-cost 32-bit control with a reduced instruction set and compact code footprint. This hierarchy connects the LPC1114FHN33/333 to Arm Cortex-M0 microcontrollers, 32-bit embedded MCUs, and general-purpose embedded semiconductors.
Key device features include 50 MHz CPU operation, 32 KB of flash for program storage, 8 KB of SRAM for working memory, and a 1.8 V to 3.6 V operating range. The 32-HVQFN package supports dense PCB layouts while providing 28 GPIO lines. Arm Keil identifies the LPC1100 series as a CMSIS-pack-supported family designed for 8-bit and 16-bit controller upgrades, metering, lighting, and alarm-system applications.
The LPC1114FHN33/333 combines an Arm Cortex-M0 RISC core with on-chip Flash and SRAM to support compact firmware without an external memory interface. Its 3.3 V-centered operating range suits conventional industrial, consumer, metering, lighting-control, and alarm-system rails. Designers must observe the package-specific exposed-pad layout and provide the recommended decoupling and thermal-via arrangement when laying out the HVQFN footprint.
Typical applications include smart energy meters, LED lighting controllers, alarm and security panels, compact sensor nodes, industrial control modules, and low-cost HMI controllers. In each case, the 50 MHz core provides useful peripheral-processing headroom, while 32 KB of flash and 8 KB of SRAM allow local code and state to remain on the MCU rather than requiring external memory.
For robust implementation, place the supply bypass capacitor close to the power pins and connect the exposed thermal pad to a properly sized copper area with thermal vias. Confirm every signal's pin assignment against the manufacturer's package pin table before PCB release, and validate firmware, clock, reset, and low-power behavior across the complete 1.8 V to 3.6 V supply range.
This page consolidates lifecycle information, package characteristics, drop-in alternatives, comparison parameters, and practical design guidance for engineers evaluating the LPC1114FHN33/333. It also distinguishes electrically similar LPC1114 variants so engineers can identify the closest package-compatible options without confusing order codes or functional differences.
ドロップイン代替品: LPC1114FHN33/333 — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
このシリーズのバリエーション
同一シリーズでドロップイン互換のモデル: LPC1114FHN33/333 (同一形状・フットプリント) — 相違点: Lifecycle Status, Package.
LPC1114FHN33/302K
✅ ドロップイン📋 参考代替品(カタログ未掲載)
LPC1114FHN33/303
✅ ドロップイン📋 参考代替品(カタログ未掲載)
LPC1114JHN33/333E
✅ ドロップイン📋 参考代替品(カタログ未掲載)
LPC1114FHN33/303Y
✅ ドロップイン📋 参考代替品(カタログ未掲載)
LPC1114FHI33
✅ ドロップイン📋 参考代替品(カタログ未掲載)
LPC1114FHN33/333 最大定格&電気的特性
| Product Type | 32-bit Arm Cortex-M0 microcontroller |
| Maximum CPU Frequency | 50 MHz |
| Flash Memory | 32 KB |
| SRAM | 8 KB |
| 動作電源電圧 | 1.8 V to 3.6 V |
| Nominal Supply Voltage | 3.3 V |
| General-Purpose I/O | 28 lines |
| Architecture | Arm Cortex-M0 RISC |
| パッケージ | 32-HVQFN, 7 mm x 7 mm |
| Package Designation | PQCC33 |
| 実装タイプ | Surface mount |
| 動作温度 | -40 °C to +85 °C |
| ライフサイクル状態 | Active |
LPC1114FHN33/333 pqcc33 ピン配置ガイド
LPC1114FHN33/333 (pqcc33 パッケージ) のピン配置。 このデジタルICには、GPIO、通信インターフェース (UART、SPI、I2C)、および電源ピンが含まれています。代替ピン機能と設定オプションについては、メーカーのデータシートを参照してください。組み込みシステム設計とPCBレイアウトに不可欠です。
詳細なピン配置データはありません: LPC1114FHN33/333.
詳細は データシート をご参照ください。
主な用途
LPC1114FHN33/333 の用途: 6 件s: Smart Energy Metering, LED Lighting Control, Alarm and Security Panels, Industrial Sensor Nodes, Compact HMI Controllers, Low-Cost HMI and Utility Controls.
Smart Energy Metering
The LPC1114FHN33/333 fits compact metering controllers that collect pulses, process sensor inputs, and maintain operating state without external memory. Its 50 MHz Arm Cortex-M0 core provides processing headroom for measurement routines, while 32 KB of flash accommodates firmware and calibration data and 8 KB of SRAM supports buffers and stack requirements. The 1.8 V to 3.6 V operating range suits regulated 3.3 V metering rails. In a meter design, the 28 GPIO lines can connect pulse inputs, display-control signals, communications, and status indicators. The 32-HVQFN package also reduces board area, although the exposed pad requires a thermal copper pattern and vias. Validate timing-critical pulse capture, low-power behavior, and calibration retention across the intended supply and temperature range.
おすすめ
LED Lighting Control
The LPC1114FHN33/333 can serve as the central controller in an LED lighting module that requires sequencing, dimming, fault monitoring, and local configuration storage. The 50 MHz Cortex-M0 core executes timing and control logic with ample bandwidth relative to simple 8-bit alternatives. Its 28 GPIO lines support LED-control outputs, switch inputs, and status signaling, while 8 KB of SRAM can hold update buffers and 32 KB of flash can retain control tables or firmware. Operation from 1.8 V to 3.6 V permits integration with 3.3 V driver electronics. The 32-HVQFN 7 x 7 mm package is useful for space-constrained lamp modules, but designers should follow the exposed-pad land pattern and place bypass capacitance close to the supply pins to limit switching-related supply disturbance.
おすすめ
Alarm and Security Panels
The LPC1114FHN33/333 is appropriate for compact alarm panels that supervise sensors, drive annunciators, and manage keypad or status-indicator interfaces. Its 32-bit Cortex-M0 architecture supports larger state machines than an 8-bit controller while retaining a cost-focused embedded implementation. The 50 MHz operating speed handles periodic sensor scanning and communication tasks, and 8 KB of SRAM is suitable for event buffers and working variables. A 3.3 V nominal rail and 1.8 V to 3.6 V operating range align with many security subsystems. The 28 GPIO lines provide broad panel connectivity, while the 32-HVQFN package helps reduce enclosure size. Critical alarm functions should be tested for startup behavior, input filtering, supply-brownout response, and firmware update recovery before deployment.
おすすめ
Industrial Sensor Nodes
The LPC1114FHN33/333 works well in a small industrial sensor node that samples switches or analog front ends, applies filtering, and reports measurements through a serial interface. Its 50 MHz Arm Cortex-M0 core provides sufficient throughput for local signal processing, while 32 KB of flash stores application code and 8 KB of SRAM accommodates samples and communication buffers. The 1.8 V to 3.6 V range supports 3.3 V process-control electronics, and 28 GPIO lines simplify sensor multiplexing, status LEDs, and interface connections. The 32-HVQFN footprint supports compact boards, but environmental robustness depends on the complete assembly rather than the MCU alone. Validate input thresholds, clock tolerance, isolation strategy, thermal rise, and transient immunity for the installation environment.
おすすめ
Compact HMI Controllers
The LPC1114FHN33/333 can coordinate a small human-machine interface built around a display, buttons, and status indicators. The 50 MHz Cortex-M0 processor manages refresh tasks and input scanning, while 32 KB of flash holds interface firmware and graphics assets and 8 KB of SRAM supports screen buffers. Twenty-eight GPIO lines can be allocated among display-control signals, capacitive or mechanical inputs, and communications. Its 1.8 V to 3.6 V supply range enables operation from 3.3 V embedded systems, and the 32-HVQFN package reduces board area for behind-panel electronics. Because display and communication peripherals can create sharp current transitions, the design should include local supply decoupling, deliberate signal-return routing, and GPIO drive-level checks based on the selected external interface.
おすすめ
Low-Cost HMI and Utility Controls
The LPC1114FHN33/333 is a practical control processor for compact utility equipment where a 32-bit CPU, local program memory, and moderate I/O are required in a small board. The 50 MHz core can execute communication stacks and control sequences, while 32 KB of flash and 8 KB of SRAM keep routine firmware resident locally. Its 28 GPIO lines support relays, status inputs, displays, and service interfaces. The nominal 3.3 V operation fits standard embedded rails, and the 1.8 V minimum can simplify matching to 1.8 V peripherals when the complete power tree permits it. The 7 x 7 mm 32-HVQFN package conserves PCB area, but exposed-pad soldering, thermal vias, and ground-return continuity remain essential for reliable industrial operation and electromagnetic compatibility.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: LPC1114FHN33/333 — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | LPC1114FHN33/302K | LPC1114FHN33/303 | LPC1114JHN33/333E | LPC1114FHN33/303Y | LPC1114FHI33 |
|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 32-HVQFN (7 x 7 mm) | 32-HVQFN (7 x 7 mm) - same package | 32-HVQFN (7 x 7 mm) - same package | 32-HVQFN (7 x 7 mm) - same package | 32-HVQFN (7 x 7 mm) - same package | 32-HVQFN (7 x 7 mm) - same package |
| CPU Core | Arm Cortex-M0 | Arm Cortex-M0 | Arm Cortex-M0 | Arm Cortex-M0 | Arm Cortex-M0 | Arm Cortex-M0 |
| Maximum CPU Frequency | 50 MHz | 50 MHz | 50 MHz | 50 MHz | 50 MHz | 50 MHz |
| Special Ordering Attributes | /333 order-code configuration | /302K order-code configuration | /303 order-code configuration | J and E suffix attributes | Y suffix attribute | I suffix attribute |
主な差別化要因
- Maintains the full LPC1114 core specification set (vs LPC1114FHN33/302K)
- Matches the established 32-HVQFN 7 x 7 mm footprint (vs LPC1114JHN33/333E)
- Provides 28 GPIO lines for compact control systems (vs LPC1114FHN33/303Y)
設計ノート
Treat the exposed pad as both a thermal and electrical land feature. Follow the manufacturer's PQCC33 land pattern, place thermal vias within or near the pad where the recommended layout permits, and connect the pad to the ground plane. Do not substitute the exposed pad for a normal perimeter pin in the schematic or PCB library.
Place the local supply bypass capacitor immediately beside the MCU power and ground pins, with a short, low-inductance return path. The device operates from 1.8 V to 3.6 V, so verify startup, brownout, and steady-state behavior at the actual rail voltage rather than assuming a nominal 3.3 V supply alone is sufficient.
Assign GPIO and clock nets directly from the manufacturer pin table, especially when using an HVQFN footprint with an exposed pad. Check alternate-function, debug, reset, and no-connect requirements before routing. For externally connected signals, include appropriate protection and ensure that any external pull network complements the MCU's configurable internal pull resistors.
コンプライアンス情報
The manufacturer identifies the LPC1114FHN33 as active, but no explicit environmental or material-compliance declaration was present in the cited product snippets. Confirm RoHS, REACH, lead-free, halogen-free, conflict-minerals, and automotive-qualification status in the current manufacturer documentation.