MAX232AMJE - 5V RS-232 Transceiver | Maxim Integrated
MPN: MAX232AMJE ✓ সক্রিয়MAX232AMJE সারাংশ
An RS-232 transceiver is an interface IC within the broader communication-IC and interface-controller hierarchy. It provides the electrical conversion between single-ended digital logic and the bipolar voltage signaling used by RS-232 equipment. This makes the MAX232AMJE suitable for connecting a host, controller, or embedded processor to a serial port, diagnostic interface, industrial control system, or other RS-232 peer.
The MAX232AMJE operates from a single 5 V supply and uses 0.1 µF external charge-pump capacitors, according to the Maxim Integrated manufacturer datasheet. Its two-driver, two-receiver arrangement supports two RS-232 channels in one package. The 200 kbps signaling rate is suitable for standard asynchronous serial communication while also providing margin for many industrial-control, instrumentation, and embedded service interfaces.
Technically, the integrated charge pumps generate the bipolar voltages required by RS-232 while the drivers add level translation and the receivers provide thresholded noise immunity. The MAX232AMJE family is intended for EIA/TIA-232E and V.28/V.24 communications interfaces, particularly where ±12 V is unavailable. Its 16-pin CERDIP construction is appropriate for through-hole industrial, telecommunications, and legacy equipment designs.
Typical uses include PC-compatible serial ports, embedded UART links, industrial controllers, test equipment, and service-console connections. In each case, the host UART connects to the logic-side pins while the RS-232 line driver pins connect through the intended cable or connector arrangement. Because RS-232 is point-to-point, each driver should connect to one receiver rather than a multi-drop bus.
When laying out the circuit, place the 0.1 µF charge-pump capacitors close to their designated pins and keep the transceiver away from high-current switching nodes. Confirm line protection, ground reference, and connector pin assignment before energizing the interface. The MAX232 family is listed in production by the manufacturer, and its long-standing through-hole package remains useful for replacement and legacy-system maintenance.
This page combines the device specifications, confirmed package information, practical interface guidance, and a focused same-package replacement comparison. It is intended to help engineers identify the correct MAX232 family member, plan the charge-pump network, and evaluate drop-in options for a 16-pin through-hole RS-232 design.
এর জন্য ড্রপ-ইন বিকল্প MAX232AMJE — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
এই সিরিজের ভ্যারিয়েন্ট
একই সিরিজের মডেল যেগুলো drop-in compatible MAX232AMJE (একই form factor এবং footprint) — পার্থক্য রয়েছে Package, Product Type, Supply Voltage.
MAX232AMJE/883B
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →MAX232AMJE-HR
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
MAX232ACPE+
✅ ড্রপ-ইনমূল্যের জন্য যোগাযোগ করুন
ডেটাশিট দেখুন →MAX232AEPE
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
MAX232AEJE
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
MAX232AMJE বিশেষণ
| Product Type | RS-232 line-driver and receiver transceiver |
| Transmit Channels | 2 channels |
| Receive Channels | 2 channels |
| সাপ্লাই ভোল্টেজ | 5 V |
| Maximum Data Rate | 200 kbps |
| Charge-Pump Capacitor | 0.1 µF |
| Supported Communication Standards | EIA/TIA-232E and V.28/V.24 |
| Output Voltage Generation | Positive and negative RS-232 levels generated on chip |
| External Supply Requirement | No ±12 V supply required |
| প্যাকেজ | 16-pin CERDIP |
| মাউন্টিং স্টাইল | Through-hole |
MAX232AMJE পিন কনফিগারেশন
| পিন 1 | R1OUT — Receiver 1 output |
| পিন 2 | R2OUT — Receiver 2 output |
| পিন 3 | R3OUT — Receiver 3 output |
| পিন 4 | R3IN — Receiver 3 input |
| পিন 5 | R2IN — Receiver 2 input |
| পিন 6 | R1IN — Receiver 1 input |
| পিন 7 | V+ — Positive charge-pump output |
| পিন 8 | GND — Ground |
| পিন 9 | V- — Negative charge-pump output |
| পিন 10 | T1IN — Driver 1 logic input |
| পিন 11 | T2IN — Driver 2 logic input |
| পিন 12 | T2OUT — Driver 2 RS-232 output |
| পিন 13 | T1OUT — Driver 1 RS-232 output |
| পিন 14 | VCC — Positive supply voltage |
| পিন 15 | C3+ — Charge-pump capacitor 3 positive terminal |
| পিন 16 | C3- — Charge-pump capacitor 3 negative terminal |
সাধারণ ব্যবহার
MAX232AMJE এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Embedded UART Serial Interfaces, Industrial Controller Connectivity, Test and Measurement Equipment, Legacy PC Serial Port Replacement, Point-to-Point Data Links, Battery-Powered Portable Equipment.
Embedded UART Serial Interfaces
The MAX232AMJE fits embedded systems that expose a conventional UART through an RS-232 connector. Its two transmitters and two receivers provide two bidirectional communication paths, while the 200 kbps maximum rate supports standard asynchronous serial traffic with useful speed margin. The device operates from 5 V and generates the required positive and negative RS-232 levels internally, so the host does not need a separate bipolar supply. In a typical circuit, the UART transmit and receive pins connect to the logic side of the transceiver, while the line-driver and receiver pins connect to the connector. Confirm the MAX232AMJE requirement for 0.1 µF charge-pump capacitors and place each capacitor close to its associated pins to minimize charge-pump disturbance.
সুপারিশকৃত
Industrial Controller Connectivity
The MAX232AMJE is suitable for connecting industrial controllers, service panels, and configuration equipment through RS-232. Its 5 V supply requirement simplifies interface design around modern embedded processors, and the 200 kbps data rate accommodates many diagnostic and supervisory protocols. On-chip charge-pump circuitry eliminates the need for a separate ±12 V supply, while the two-driver and two-receiver configuration supports more than one point-to-point link in a single package. For industrial use, keep the transceiver separated from motors, relays, and high-current switching stages, and include suitable connector protection against surge and ESD events. The external charge-pump network should use the recommended 0.1 µF capacitors, with short routed paths and a stable ground reference to the connector shield system.
সুপারিশকৃত
Test and Measurement Equipment
The MAX232AMJE can provide RS-232 connectivity for test instruments, programmable equipment, and laboratory control systems. The 200 kbps rate is suitable for legacy instrument-control protocols, while the 16-pin CERDIP package supports repair and upgrade boards that retain through-hole construction. The transceiver’s two channels allow separate transmit and receive paths, and the integrated charge pumps reduce the number of external voltage rails required. Use clean logic grounding and isolate the RS-232 line from chassis and signal grounds as required by the system architecture. Decoupling should follow the manufacturer recommendations, and the 0.1 µF charge-pump capacitors should be positioned close to the relevant device pins. Verify the connector’s DTE or DCE assignment and confirm that the target instrument uses compatible signal polarity.
সুপারিশকৃত
Legacy PC Serial Port Replacement
The MAX232AMJE is a practical choice for maintaining or recreating a legacy PC-style serial interface in equipment that still uses the RS-232 electrical standard. It translates between CMOS/TTL UART signals and bipolar RS-232 levels from a single 5 V supply, avoiding the original design requirement for a separate ±12 V rail. The 200 kbps rate exceeds the rate commonly required by basic configuration ports and supports faster data-transfer modes. The 16-pin CERDIP package also suits older motherboard and backplane layouts. Before replacement, inspect the board for 0.1 µF charge-pump capacitors and confirm that the pin arrangement follows the MAX232 family pinout. A modern SMD interface IC cannot be substituted without a PCB redesign because surface-mount and through-hole land patterns are different.
সুপারিশকৃত
Point-to-Point Data Links
The MAX232AMJE supports point-to-point RS-232 links such as controller-to-controller, terminal-to-interface, or equipment-to-service-console connections. Its 200 kbps maximum rate accommodates many asynchronous protocols, and the two transmitters and two receivers permit more flexible cable routing than a single-channel device. Because RS-232 is not a multi-drop bus, connect each driver to one receiver and keep the link topology unambiguous. The 5 V operating supply and integrated bipolar voltage generation simplify power allocation in compact systems. Use the specified 0.1 µF charge-pump capacitors and keep their loop area small. For cables longer than the intended equipment environment, add suitable transient protection and verify that the grounding arrangement follows the connector and system requirements.
সুপারিশকৃত
Battery-Powered Portable Equipment
The MAX232AMJE can support portable or battery-powered equipment that needs an RS-232 port without operating a separate ±12 V supply. Its charge-pump circuit derives bipolar signal levels from the 5 V rail, while the MAX220–MAX249 family is specifically identified as useful in systems where ±12 V is unavailable. The 200 kbps rate allows use with fast UART links, and the available shutdown behavior in the family can help conserve power when the interface is not active. Care is required because the target’s exact supply current and shutdown timing are not specified here. Confirm those limits in the manufacturer datasheet and account for the charge-pump capacitors’ effective AC loading. Use the 0.1 µF capacitor recommendation for stable operation across temperature and supply tolerance.
সুপারিশকৃত
সুপারিশকৃত পণ্যের সারসংক্ষেপ
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা MAX232AMJE — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | MAX232AMJE/883B | MAX232AMJE-HR | MAX232ACPE | MAX232AEPE | MAX232AEJE |
|---|---|---|---|---|---|---|
| Brand | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated |
| Package | 16-pin CERDIP | 16-CDIP | 16-pin CERDIP | 16-pin CERDIP | 16-pin CERDIP | 16-pin CERDIP |
| Transmit Channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels |
| Receive Channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels |
| Maximum Data Rate | 200 kbps | 200 kbps | 200 kbps | 200 kbps | 200 kbps | 200 kbps |
| Supply Voltage | 5 V | 5 V | 5 V | 5 V | 5 V | 5 V |
| Recommended Charge-Pump Capacitor | 0.1 µF | 0.1 µF | 0.1 µF | 0.1 µF | 0.1 µF | 0.1 µF |
| Interface Standard | EIA/TIA-232E and V.28/V.24 | EIA/TIA-232E and V.28/V.24 | EIA/TIA-232E and V.28/V.24 | EIA/TIA-232E and V.28/V.24 | EIA/TIA-232E and V.28/V.24 | EIA/TIA-232E and V.28/V.24 |
| Mounting Style | Through-hole | Through-hole | Through-hole | Through-hole | Through-hole | Through-hole |
| Qualification Variant | Commercial MAX232AMJE | 883B military-processing designation | HR designation | MAX232A commercial variant | MAX232AE commercial variant | MAX232AE commercial variant |
মূল পার্থক্যসমূহ
- Higher data rate than MAX232MJE (বনামMAX232MJE)
- Single 5 V power rail (বনামMAX232AMJE/883B)
- Matched 200 kbps replacement family (বনামMAX232ACPE)
- Through-hole footprint retention (বনামMAX232EESE+T)
ডিজাইন নোট
Use 0.1 µF for all charge-pump capacitors in the MAX232AMJE design and place them directly between the designated pins with minimal loop area. The MAX232MJE can operate with either 0.1 µF or 1 µF, but the AMJE recommendation is 0.1 µF. A board populated with 1 µF capacitors should not be treated as an automatic AMJE conversion without checking the family-specific operating recommendations and signal integrity.
Route UART logic signals away from the RS-232 connector, cable shield, and switching-power stages. Keep the transceiver ground reference close to the device ground and use the board’s established chassis or signal-ground strategy at the connector. Long RS-232 traces and cables can pick up transients, so place any protection network near the connector while keeping the protection return path short and controlled.
Do not treat every 16-pin MAX232-family suffix as electrically identical. MAX232AMJE and MAX232MJE differ in data rate and accepted charge-pump capacitance, while 883B and HR versions represent distinct qualification choices. Before substitution, verify the pin names, 0.1 µF capacitor recommendation, 200 kbps requirement, temperature range, and any military-processing or reliability requirements.
কমপ্লায়েন্স তথ্য
The MAX232 family is listed in production by the manufacturer. Exact RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations for the MAX232AMJE ordering code were not identified.