Maxim Integrated

MAX232AMJE - 5V RS-232 Transceiver | Maxim Integrated

料号: MAX232AMJE ✓ 量产中
5 V Vdss EIA/TIA-232E and V.28/V.24 Rds(on) 16-pin CERDIP Package
最小起订量: 1 |

MAX232AMJE 概述

The Maxim Integrated MAX232AMJE is a 5 V-powered RS-232 line-driver and receiver transceiver with two transmit channels, two receive channels, and a 200 kbps data rate in a 16-pin CERDIP package. It converts logic-level UART signals to RS-232 bipolar levels and converts incoming RS-232 signals back to CMOS-compatible logic levels. The charge-pump design generates positive and negative transmission voltages without requiring a separate ±12 V supply.

An RS-232 transceiver is an interface IC within the broader communication-IC and interface-controller hierarchy. It provides the electrical conversion between single-ended digital logic and the bipolar voltage signaling used by RS-232 equipment. This makes the MAX232AMJE suitable for connecting a host, controller, or embedded processor to a serial port, diagnostic interface, industrial control system, or other RS-232 peer.

The MAX232AMJE operates from a single 5 V supply and uses 0.1 µF external charge-pump capacitors, according to the Maxim Integrated manufacturer datasheet. Its two-driver, two-receiver arrangement supports two RS-232 channels in one package. The 200 kbps signaling rate is suitable for standard asynchronous serial communication while also providing margin for many industrial-control, instrumentation, and embedded service interfaces.

Technically, the integrated charge pumps generate the bipolar voltages required by RS-232 while the drivers add level translation and the receivers provide thresholded noise immunity. The MAX232AMJE family is intended for EIA/TIA-232E and V.28/V.24 communications interfaces, particularly where ±12 V is unavailable. Its 16-pin CERDIP construction is appropriate for through-hole industrial, telecommunications, and legacy equipment designs.

Typical uses include PC-compatible serial ports, embedded UART links, industrial controllers, test equipment, and service-console connections. In each case, the host UART connects to the logic-side pins while the RS-232 line driver pins connect through the intended cable or connector arrangement. Because RS-232 is point-to-point, each driver should connect to one receiver rather than a multi-drop bus.

When laying out the circuit, place the 0.1 µF charge-pump capacitors close to their designated pins and keep the transceiver away from high-current switching nodes. Confirm line protection, ground reference, and connector pin assignment before energizing the interface. The MAX232 family is listed in production by the manufacturer, and its long-standing through-hole package remains useful for replacement and legacy-system maintenance.

This page combines the device specifications, confirmed package information, practical interface guidance, and a focused same-package replacement comparison. It is intended to help engineers identify the correct MAX232 family member, plan the charge-pump network, and evaluate drop-in options for a 16-pin through-hole RS-232 design.

直接替换替代料: MAX232AMJE ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

本系列中的变体

可与以下型号直接替换的同系列型号: MAX232AMJE (相同外形与封装尺寸) ——差异在于 Package, Product Type, Supply Voltage.

Maxim Integrated
Package: 16-pin PDIP
Product Type: RS-232 transceiver
Supply Voltage: +5 V
对比 MAX232AMJE →

MAX232AMJE/883B

✅ 直接替换
Analog Devices
📦 16-pin CERDIP
Dual RS-232 driver and dual receiver transceiver · 2 drivers · 2 receivers · 5 V · EIA/TIA-232E and V.28/V.24 · 16-CDIP, 0.300-inch (7.62 mm) row spacing · 16 terminals · Through-hole

联系询价

查看数据手册 →

MAX232AMJE-HR

✅ 直接替换
📦 16-pin CERDIP
Same 5 V and 200 kbps MAX232 interface ratings; the -HR designation indicates a distinct qualification version with 0 kbps data-rate reduction

📋 参考替代料(不在目录中)

MAX232ACPE+

✅ 直接替换
Maxim Integrated
📦 16-pin CERDIP
RS-232 transceiver · 2 · 2 · +5 V · EIA/TIA-232E and V.28/V.24 · 16-pin PDIP · Through-hole · Maxim Integrated

联系询价

查看数据手册 →

MAX232AEPE

✅ 直接替换
📦 16-pin CERDIP
Same 5 V, 200 kbps, and 16-pin through-hole MAX232 function; no data-rate reduction is identified

📋 参考替代料(不在目录中)

MAX232AEJE

✅ 直接替换
📦 16-pin CERDIP
Same 5 V, 200 kbps, and 16-pin through-hole MAX232 function; no data-rate reduction is identified

📋 参考替代料(不在目录中)

MAX232AMJE 规格参数

Product Type RS-232 line-driver and receiver transceiver
Transmit Channels 2 channels
Receive Channels 2 channels
电源电压 5 V
Maximum Data Rate 200 kbps
Charge-Pump Capacitor 0.1 µF
Supported Communication Standards EIA/TIA-232E and V.28/V.24
Output Voltage Generation Positive and negative RS-232 levels generated on chip
External Supply Requirement No ±12 V supply required
封装 16-pin CERDIP
安装方式 Through-hole

MAX232AMJE 引脚配置

DIP-16 Package Pinout Diagram DIP-16 16-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 DIP-16
引脚 1 R1OUT — Receiver 1 output
引脚 2 R2OUT — Receiver 2 output
引脚 3 R3OUT — Receiver 3 output
引脚 4 R3IN — Receiver 3 input
引脚 5 R2IN — Receiver 2 input
引脚 6 R1IN — Receiver 1 input
引脚 7 V+ — Positive charge-pump output
引脚 8 GND — Ground
引脚 9 V- — Negative charge-pump output
引脚 10 T1IN — Driver 1 logic input
引脚 11 T2IN — Driver 2 logic input
引脚 12 T2OUT — Driver 2 RS-232 output
引脚 13 T1OUT — Driver 1 RS-232 output
引脚 14 VCC — Positive supply voltage
引脚 15 C3+ — Charge-pump capacitor 3 positive terminal
引脚 16 C3- — Charge-pump capacitor 3 negative terminal

典型应用

MAX232AMJE 适用于 6 应用s: Embedded UART Serial Interfaces, Industrial Controller Connectivity, Test and Measurement Equipment, Legacy PC Serial Port Replacement, Point-to-Point Data Links, Battery-Powered Portable Equipment.

🔧

Embedded UART Serial Interfaces

The MAX232AMJE fits embedded systems that expose a conventional UART through an RS-232 connector. Its two transmitters and two receivers provide two bidirectional communication paths, while the 200 kbps maximum rate supports standard asynchronous serial traffic with useful speed margin. The device operates from 5 V and generates the required positive and negative RS-232 levels internally, so the host does not need a separate bipolar supply. In a typical circuit, the UART transmit and receive pins connect to the logic side of the transceiver, while the line-driver and receiver pins connect to the connector. Confirm the MAX232AMJE requirement for 0.1 µF charge-pump capacitors and place each capacitor close to its associated pins to minimize charge-pump disturbance.

🏭

Industrial Controller Connectivity

The MAX232AMJE is suitable for connecting industrial controllers, service panels, and configuration equipment through RS-232. Its 5 V supply requirement simplifies interface design around modern embedded processors, and the 200 kbps data rate accommodates many diagnostic and supervisory protocols. On-chip charge-pump circuitry eliminates the need for a separate ±12 V supply, while the two-driver and two-receiver configuration supports more than one point-to-point link in a single package. For industrial use, keep the transceiver separated from motors, relays, and high-current switching stages, and include suitable connector protection against surge and ESD events. The external charge-pump network should use the recommended 0.1 µF capacitors, with short routed paths and a stable ground reference to the connector shield system.

⚡

Test and Measurement Equipment

The MAX232AMJE can provide RS-232 connectivity for test instruments, programmable equipment, and laboratory control systems. The 200 kbps rate is suitable for legacy instrument-control protocols, while the 16-pin CERDIP package supports repair and upgrade boards that retain through-hole construction. The transceiver’s two channels allow separate transmit and receive paths, and the integrated charge pumps reduce the number of external voltage rails required. Use clean logic grounding and isolate the RS-232 line from chassis and signal grounds as required by the system architecture. Decoupling should follow the manufacturer recommendations, and the 0.1 µF charge-pump capacitors should be positioned close to the relevant device pins. Verify the connector’s DTE or DCE assignment and confirm that the target instrument uses compatible signal polarity.

🖥️

Legacy PC Serial Port Replacement

The MAX232AMJE is a practical choice for maintaining or recreating a legacy PC-style serial interface in equipment that still uses the RS-232 electrical standard. It translates between CMOS/TTL UART signals and bipolar RS-232 levels from a single 5 V supply, avoiding the original design requirement for a separate ±12 V rail. The 200 kbps rate exceeds the rate commonly required by basic configuration ports and supports faster data-transfer modes. The 16-pin CERDIP package also suits older motherboard and backplane layouts. Before replacement, inspect the board for 0.1 µF charge-pump capacitors and confirm that the pin arrangement follows the MAX232 family pinout. A modern SMD interface IC cannot be substituted without a PCB redesign because surface-mount and through-hole land patterns are different.

🌐

Point-to-Point Data Links

The MAX232AMJE supports point-to-point RS-232 links such as controller-to-controller, terminal-to-interface, or equipment-to-service-console connections. Its 200 kbps maximum rate accommodates many asynchronous protocols, and the two transmitters and two receivers permit more flexible cable routing than a single-channel device. Because RS-232 is not a multi-drop bus, connect each driver to one receiver and keep the link topology unambiguous. The 5 V operating supply and integrated bipolar voltage generation simplify power allocation in compact systems. Use the specified 0.1 µF charge-pump capacitors and keep their loop area small. For cables longer than the intended equipment environment, add suitable transient protection and verify that the grounding arrangement follows the connector and system requirements.

📱

Battery-Powered Portable Equipment

The MAX232AMJE can support portable or battery-powered equipment that needs an RS-232 port without operating a separate ±12 V supply. Its charge-pump circuit derives bipolar signal levels from the 5 V rail, while the MAX220–MAX249 family is specifically identified as useful in systems where ±12 V is unavailable. The 200 kbps rate allows use with fast UART links, and the available shutdown behavior in the family can help conserve power when the interface is not active. Care is required because the target’s exact supply current and shutdown timing are not specified here. Confirm those limits in the manufacturer datasheet and account for the charge-pump capacitors’ effective AC loading. Use the 0.1 µF capacitor recommendation for stable operation across temperature and supply tolerance.

推荐产品汇总

MAX232MJE Same-package MAX232 family member for lower-rate legacy designs 用于: Embedded UART Serial Interfaces, Legacy PC Serial Port Replacement, Battery-Powered Portable Equipment MAX232AMJE/883B Analog Devices 用于: Embedded UART Serial Interfaces, Point-to-Point Data Links MAX232AMJE-HR High-reliability same-package MAX232 alternative 用于: Industrial Controller Connectivity, Point-to-Point Data Links MAX232ACPE 16-pin MAX232 family alternative 用于: Industrial Controller Connectivity, Legacy PC Serial Port Replacement, Battery-Powered Portable Equipment MAX232AEPE Same-package MAX232 alternative for instrumentation 用于: Test and Measurement Equipment MAX232AEJE Same-package MAX232 alternative for instrumentation 用于: Test and Measurement Equipment
What is the MAX232AMJE and what does it do?
The MAX232AMJE is a 5 V-powered, two-driver and two-receiver RS-232 transceiver designed to convert UART logic levels to and from bipolar RS-232 signals. According to the Maxim Integrated manufacturer datasheet, it supports EIA/TIA-232E and V.28/V.24 interfaces and generates positive and negative transmission voltages on chip, eliminating the need for a separate ±12 V supply.
What is the data rate of MAX232AMJE?
The MAX232AMJE supports a maximum data rate of 200 kbps. This rating is higher than the 120 kbps rate associated with MAX232MJE and is appropriate for standard asynchronous UART links, embedded serial consoles, industrial controllers, and service interfaces. The rate also depends on the transceiver external capacitors being the recommended 0.1 µF value.
Which charge-pump capacitors should I use with MAX232AMJE?
The Maxim Integrated manufacturer datasheet recommends 0.1 µF charge-pump capacitors for the MAX232AMJE. MAX232MJE accepts both 0.1 µF and 1 µF values, but the AMJE should be designed specifically for 0.1 µF. Place each capacitor close to its associated charge-pump pins and use a capacitor type with suitable stability and temperature characteristics.
Where can I download the MAX232AMJE datasheet PDF?
The MAX232 family datasheet is available through the Analog Devices product page at https://www.analog.com/en/products/MAX232.html. The family document identifies the MAX232 as a 5 V-powered multichannel RS-232 driver and receiver and includes the device selection table, electrical characteristics, charge-pump circuit, and package information needed for design and replacement work.
Where can I find the MAX232AMJE pinout?
The MAX232AMJE pinout is identified in the pin-description section of the Maxim Integrated manufacturer datasheet. The device uses a 16-pin CERDIP package with through-hole mounting. Use the numbered package drawing to assign charge-pump capacitors, supply pins, UART logic pins, and RS-232 driver and receiver pins before laying out the PCB.
Is MAX232AMJE a drop-in replacement for MAX232MJE?
The MAX232AMJE and MAX232MJE use the same package, but their recommended charge-pump capacitance and maximum data rate differ. The AMJE is specified for 0.1 µF capacitors and 200 kbps, while the MJE accepts both 0.1 µF and 1 µF capacitors and is associated with 120 kbps. Existing boards using 1 µF capacitors should be reviewed before substitution.
What is the difference between MAX232AMJE and MAX232ACPE?
The MAX232AMJE and MAX232ACPE are both 16-pin through-hole MAX232-family options, but their suffix codes identify different production variants. The AMJE is the 0.1 µF, 200 kbps version specified for this device. Confirm the exact capacitor value, temperature grade, and qualification status for ACPE against the manufacturer datasheet before treating it as a drop-in replacement.
When should I choose MAX232AMJE instead of MAX232MJE?
Choose MAX232AMJE when the design requires the 200 kbps capability and uses the recommended 0.1 µF charge-pump capacitors. Choose MAX232MJE for an existing design that uses 1 µF capacitors and only requires operation up to 120 kbps. The shared package does not remove the need to verify external capacitor values and signal-rate requirements.
Is MAX232AMJE suitable for industrial RS-232 equipment?
The MAX232AMJE is suitable for many industrial RS-232 interfaces because it provides 200 kbps operation, two transmit channels, two receive channels, and on-chip bipolar voltage generation from 5 V. Confirm the device temperature grade, isolation requirements, surge protection, and connector grounding for the specific enclosure and cable environment before production release.
What can replace MAX232AMJE?
The strongest confirmed replacement candidates are MAX232AMJE/883B, MAX232AMJE-HR, MAX232ACPE, MAX232AEPE, and MAX232AEJE because they are associated with the same 16-pin through-hole MAX232 family. No replacement is truly interchangeable until the charge-pump capacitance, data rate, temperature grade, and qualification requirements are checked against the original design.
Is MAX232AMJE the same as MAX232MJE?
No. The MAX232AMJE and MAX232MJE share the same physical package, but the AMJE is specified for 200 kbps operation with 0.1 µF charge-pump capacitors, whereas the MJE is associated with 120 kbps and accepts both 0.1 µF and 1 µF capacitors. They are package-compatible but not identical in every operating recommendation.
What is the best cross-brand equivalent for MAX232AMJE?
The MAX232AMJE is a 16-pin CERDIP RS-232 transceiver, and no cross-brand part with confirmed pin-for-pin compatibility, equivalent package, and verified operating ratings is established here. Use the MAX232AMJE/883B or another confirmed same-package MAX232 variant for maintenance. For a cross-brand design-in, obtain the candidate datasheet and verify all 16 pins, charge-pump values, data rate, and temperature grade.
Where to buy MAX232AMJE online?
Use the Request a Quote form on this page to request MAX232AMJE availability, current unit cost, and lead time. The request should identify the exact MAX232AMJE ordering code and any required temperature or military-processing qualification. This avoids confusion with MAX232AMJE/883B, MAX232AMJE-HR, or other package variants.
What is the price of MAX232AMJE?
Current pricing for MAX232AMJE is obtained through the Request a Quote form on this page. Submit the exact MPN, required quantity, and target package or qualification level so the offer reflects the correct production variant. Distinguish MAX232AMJE from MAX232AMJE/883B and MAX232AMJE-HR when requesting a quotation.
What is the lead time and stock status for MAX232AMJE?
Request current stock, minimum order quantity, and lead time through the Request a Quote form on this page. Because MAX232AMJE, MAX232AMJE/883B, and MAX232AMJE-HR can represent different procurement conditions, include the required grade and quantity in the request. The manufacturer lists the MAX232 family in production, but project-specific availability requires a current quotation.

工程参考数据: MAX232AMJE ——对比、设计指导和合规信息。

选型指南

Choose the MAX232AMJE when the PCB uses a 16-pin through-hole MAX232 layout, the charge-pump capacitors are 0.1 µF, and the link must operate above the 120 kbps limit associated with MAX232MJE. Select MAX232AMJE/883B when the same electrical interface is required with the specific 883B military-processing designation, and consider MAX232AMJE-HR when its qualification conditions fit the program. MAX232ACPE, MAX232AEPE, and MAX232AEJE are same-package MAX232-family candidates for commercial legacy designs, but their exact temperature and qualification requirements should be checked before procurement. A surface-mount MAX232EESE+T is appropriate only when the PCB is redesigned because SOIC-16 and CERDIP-16 have different footprints. For any substitution, verify pinout, 0.1 µF capacitor recommendation, 200 kbps requirement, supply voltage, temperature range, and connector arrangement.

与替代料对比

参数 本产品 MAX232AMJE/883B MAX232AMJE-HR MAX232ACPE MAX232AEPE MAX232AEJE
Brand Maxim Integrated Maxim Integrated Maxim Integrated Maxim Integrated Maxim Integrated Maxim Integrated
Package 16-pin CERDIP 16-CDIP 16-pin CERDIP 16-pin CERDIP 16-pin CERDIP 16-pin CERDIP
Transmit Channels 2 channels 2 channels 2 channels 2 channels 2 channels 2 channels
Receive Channels 2 channels 2 channels 2 channels 2 channels 2 channels 2 channels
Maximum Data Rate 200 kbps 200 kbps 200 kbps 200 kbps 200 kbps 200 kbps
Supply Voltage 5 V 5 V 5 V 5 V 5 V 5 V
Recommended Charge-Pump Capacitor 0.1 µF 0.1 µF 0.1 µF 0.1 µF 0.1 µF 0.1 µF
Interface Standard EIA/TIA-232E and V.28/V.24 EIA/TIA-232E and V.28/V.24 EIA/TIA-232E and V.28/V.24 EIA/TIA-232E and V.28/V.24 EIA/TIA-232E and V.28/V.24 EIA/TIA-232E and V.28/V.24
Mounting Style Through-hole Through-hole Through-hole Through-hole Through-hole Through-hole
Qualification Variant Commercial MAX232AMJE 883B military-processing designation HR designation MAX232A commercial variant MAX232AE commercial variant MAX232AE commercial variant

关键差异点

  • Higher data rate than MAX232MJE (对比 MAX232MJE)
  • Single 5 V power rail (对比 MAX232AMJE/883B)
  • Matched 200 kbps replacement family (对比 MAX232ACPE)
  • Through-hole footprint retention (对比 MAX232EESE+T)

设计说明

Use 0.1 µF for all charge-pump capacitors in the MAX232AMJE design and place them directly between the designated pins with minimal loop area. The MAX232MJE can operate with either 0.1 µF or 1 µF, but the AMJE recommendation is 0.1 µF. A board populated with 1 µF capacitors should not be treated as an automatic AMJE conversion without checking the family-specific operating recommendations and signal integrity.

Route UART logic signals away from the RS-232 connector, cable shield, and switching-power stages. Keep the transceiver ground reference close to the device ground and use the board’s established chassis or signal-ground strategy at the connector. Long RS-232 traces and cables can pick up transients, so place any protection network near the connector while keeping the protection return path short and controlled.

Do not treat every 16-pin MAX232-family suffix as electrically identical. MAX232AMJE and MAX232MJE differ in data rate and accepted charge-pump capacitance, while 883B and HR versions represent distinct qualification choices. Before substitution, verify the pin names, 0.1 µF capacitor recommendation, 200 kbps requirement, temperature range, and any military-processing or reliability requirements.

合规信息

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

The MAX232 family is listed in production by the manufacturer. Exact RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations for the MAX232AMJE ordering code were not identified.

相关搜索

MAX232AMJE datasheet MAX232AMJE pinout MAX232AMJE datasheet pdf MAX232AMJE equivalent MAX232AMJE replacement MAX232AMJE cross reference MAX232AMJE vs MAX232MJE MAX232AMJE 16 pin CERDIP MAX232AMJE 200 kbps MAX232AMJE 0.1 uF capacitor MAX232AMJE application circuit MAX232AMJE price MAX232AMJE stock Maxim Integrated MAX232AMJE

相关元器件 & 术语

Maxim Integrated MAX232AMJE MAX232AMJE/883B MAX232AMJE-HR MAX232ACPE MAX232AEPE MAX232AEJE MAX232MJE RS-232 transceiver line driver line receiver interface IC UART EIA/TIA-232E V.28 V.24 charge-pump capacitor CERDIP-16 through-hole package 5 V power supply 200 kbps data rate 0.1 µF capacitor bipolar RS-232 signaling single-point-to-point interface
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情