Texas Instruments

MAX232EIDRG4 - Protected Dual RS-232 Transceiver | Texas Instruments

MPN: MAX232EIDRG4 ✓ সক্রিয়
5 V Vdss 16-pin SOIC Package
সর্বনিম্ন অর্ডার পরিমাণ: 1 |

MAX232EIDRG4 সারাংশ

The Texas Instruments MAX232EIDRG4 is a dual RS-232 driver and receiver with IEC 61000-4-2 protection, operating from a single 5 V supply and supporting data rates to 120 kbit/s. It provides two driver channels and two receiver channels, accepts input levels to ±30 V, and is packaged in a 16-pin SOIC. The integrated protection distinguishes this E-series device from basic RS-232 interface circuits and is intended for ports exposed to electrostatic-discharge transients.

An RS-232 transceiver is an interface IC that translates logic-level signals between a host or controller and a RS-232 link. Within the interface hierarchy, the MAX232EIDRG4 combines a line driver, receiver, charge-pump voltage supply, and electrostatic-discharge protection in one package. It is commonly placed between TTL or CMOS UART circuitry and an external DB9, terminal-block, or cable connection when an RS-232 port requires ± voltage signaling.

Key features include two drivers, two receivers, operation from one 5 V supply, and 1.0 µF charge-pump capacitors. The device operates to 120 kbit/s and accepts receiver input voltages of ±30 V. It meets or exceeds TIA/RS-232-F and ITU Recommendation V.28. These characteristics make it suitable for legacy industrial equipment, point-of-sale systems, test instruments, and computer peripherals using asynchronous RS-232 communication.

The MAX232 interface architecture uses internal charge pumps to generate the positive and negative voltages required by RS-232 drivers. Separate driver and receiver channels allow two simultaneous communication directions, while the E-series protection network reduces vulnerability to IEC 61000-4-2 discharge events on exposed lines. Because RS-232 is a single-ended, unbalanced interface, board layout, grounding, cable routing, and connector selection remain important to practical signal integrity.

Typical uses include configuration links between industrial controllers and service equipment, diagnostic ports on test and measurement systems, serial communication in POS terminals, and legacy computer or peripheral interfaces. In these applications, the device provides the voltage conversion needed by a UART while the system-side logic continues to use normal TTL or CMOS levels.

Place the required charge-pump capacitors close to their designated pins and route each protected RS-232 line directly toward its connector. Confirm line polarity, ground continuity, and the voltage rating of the connector before energizing the interface. Review the manufacturer datasheet for the exact external-capacitor values, input thresholds, and protection configuration before releasing a production design.

এর জন্য ড্রপ-ইন বিকল্প MAX232EIDRG4 — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।

MAX232IDRG4

✅ ড্রপ-ইন
Texas Instruments
📦 16-SOIC
Dual RS-232 driver/receiver transceiver · 2 · 2 · 120 kbit/s · 5 V · 8 mA typical · ±30 V maximum · 1.0 µF

মূল্যের জন্য যোগাযোগ করুন

ডেটাশিট দেখুন →

MAX232ECSE

✅ ড্রপ-ইন
📦 16-SOIC
Both are MAX232E-series 2/2-channel RS-232 interfaces; package and core data-rate class are retained, while exact charge-pump, protection, and temperature-grade differences require datasheet confirmation.

📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)

MAX232EIDRG4 বিশেষণ

Product Type Dual RS-232 driver/receiver transceiver
Number of Drivers 2 channels
Number of Receivers 2 channels
সাপ্লাই ভোল্টেজ 5 V
Maximum Data Rate 120 kbit/s
Charge-Pump Capacitor Value 1.0 µF
Receiver Input Voltage Range -30 V to +30 V
অপারেটিং তাপমাত্রার পরিসর -40 °C to +85 °C
প্যাকেজ 16-pin SOIC
Electrostatic-Discharge Protection IEC 61000-4-2
RS-232 Compliance TIA/RS-232-F
ITU Recommendation V.28
মাউন্টিং টাইপ Surface mount

MAX232EIDRG4 16-pin soic পিন কনফিগারেশন গাইড

MAX232EIDRG4 (16-pin soic প্যাকেজ)-এর পিন কনফিগারেশন। পিন নম্বরিং, ফাংশন এবং সংযোগ ডায়াগ্রাম প্রস্তুতকারকের ডেটাশিটে সংজ্ঞায়িত করা আছে। সঠিক ফুটপ্রিন্ট এবং সোল্ডারিং নির্দেশিকার জন্য এটি দেখুন।

MAX232EIDRG4-এর জন্য 16-pin soic প্যাকেজ পিনআউট ডায়াগ্রাম

এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি MAX232EIDRG4.

দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।

সাধারণ ব্যবহার

MAX232EIDRG4 এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Industrial Controller Service Port, Test and Measurement Equipment, Point-of-Sale Terminal, Computer Peripheral Interface, Embedded Data Acquisition Unit, Remote Monitoring and Control.

🏭

Industrial Controller Service Port

The MAX232EIDRG4 fits a service port that must bridge a 3.3 V or 5 V UART controller to an RS-232 connector. Its two driver and two receiver channels support bidirectional serial communication, while the 120 kbit/s capability is sufficient for command, diagnostic, and configuration traffic. The 5 V supply requirement simplifies use with common embedded rails, and 1.0 µF charge-pump capacitors support the on-chip voltage conversion. IEC 61000-4-2 protection is particularly relevant when the connector is accessible to maintenance personnel or connected to longer field cables. Confirm connector pinout and interface levels before deployment.

🔧

Test and Measurement Equipment

The MAX232EIDRG4 is appropriate for test instruments that expose an RS-232 configuration or trigger interface to operators and service technicians. The dual-channel arrangement allows two serial links or a full-duplex pair, and the 120 kbit/s rate supports instrument-control protocols, boot-loader traffic, and legacy data capture. Operation from a single 5 V rail and the -40 °C to +85 °C rating support laboratory and industrial test environments. The E-series ESD protection adds a useful layer at an exposed connector, although chassis grounding and external surge protection may still be required for long cables.

🖥️

Point-of-Sale Terminal

A point-of-sale terminal can use the MAX232EIDRG4 to connect a UART-based controller, receipt printer, or customer-display peripheral through RS-232. The two transmitters and two receivers support a practical mix of communication ports, while the 120 kbit/s maximum accommodates legacy point-of-sale protocols. A single 5 V supply simplifies integration with terminal electronics, and the protected E-series configuration is useful when the connector is accessible in a retail environment. System designers should still route the RS-232 return ground correctly, use twisted-pair cabling, and verify whether the peripheral requires hardware flow control.

💻

Computer Peripheral Interface

The MAX232EIDRG4 supports legacy computer peripherals that expose an RS-232 port for configuration, diagnostics, or low-speed data transfer. Its 2/2-channel organization permits two driver outputs and two receiver inputs, while operation to 120 kbit/s is suitable for many peripheral protocols and service commands. The 16-SOIC package simplifies assembly in compact industrial computers and embedded controllers. Where the port is user-accessible, the documented IEC 61000-4-2 protection is advantageous. Confirm whether the equipment expects RS-232 signal polarity, connector gender, or flow-control signals before laying out the board.

📡

Embedded Data Acquisition Unit

The MAX232EIDRG4 can connect a data-acquisition controller or embedded logger to an RS-232 instrument, sensor, or service computer. Its 120 kbit/s maximum data rate is appropriate for command traffic, sampled status data, and legacy laboratory equipment. Two receiver and two driver channels allow a compact multi-port implementation without adding another transceiver package. The single 5 V supply and -40 °C to +85 °C range suit embedded equipment deployed in controlled industrial environments. ESD protection on exposed lines improves robustness, but designers should keep the ground reference continuous and consider galvanic isolation where large ground-potential differences are possible.

🧩

Remote Monitoring and Control

The MAX232EIDRG4 is useful in remote monitoring equipment that uses a wired RS-232 link for configuration, telemetry, or alarm reporting. Its protected E-series construction addresses IEC 61000-4-2 discharge exposure at accessible ports, while the dual transmitter and receiver arrangement can support separate command and status channels. The 5 V supply is compatible with many embedded power systems, and the 120 kbit/s rate exceeds typical supervisory-character rates. For installations spanning separate power systems, include isolation and robust grounding to avoid surge damage or communication errors that cannot be solved by the transceiver's internal ESD protection alone.

What is the MAX232EIDRG4 used for?
The MAX232EIDRG4 is a dual RS-232 transceiver used to connect TTL or CMOS UART logic to a two-wire RS-232 port. According to the Texas Instruments datasheet, it combines two drivers, two receivers, a single 5 V supply, 120 kbit/s operation, and IEC 61000-4-2 protection in a 16-pin SOIC package. It is especially useful where exposed serial lines require stronger electrostatic-discharge protection than a basic MAX232 interface.
Where can I download the MAX232EIDRG4 datasheet PDF?
The MAX232EIDRG4 manufacturer datasheet is available through the Texas Instruments product documentation for the MAX232E family. It describes the 16-pin SOIC pin configuration, electrical characteristics, external charge-pump capacitors, RS-232 compliance, and IEC 61000-4-2 protection. Use the manufacturer datasheet for production design decisions because it provides the authoritative pin descriptions, test conditions, and absolute maximum ratings.
Where is the MAX232EIDRG4 pinout located?
The MAX232EIDRG4 pinout is shown in the pin-configuration section of the Texas Instruments MAX232E datasheet. The device uses a 16-pin SOIC package and includes charge-pump capacitor connections, supply, ground, two driver inputs and outputs, and two receiver inputs and outputs. Assign PCB nets from the numbered package drawing rather than relying only on functional groupings, and preserve the standard SOIC pin-1 orientation.
What are the key specifications of MAX232EIDRG4 that engineers should know?
The MAX232EIDRG4 provides two RS-232 drivers and two receivers, operates from one 5 V supply, supports rates to 120 kbit/s, and accepts receiver inputs to ±30 V. The Texas Instruments datasheet also identifies 1.0 µF charge-pump capacitors, IEC 61000-4-2 protection, a -40 °C to +85 °C operating range, and a 16-pin SOIC package. These specifications define its main electrical, environmental, and footprint constraints.
Is the MAX232EIDRG4 pin-compatible with the MAX232IDRG4?
The MAX232IDRG4 is a 16-SOIC RS-232 interface with the same 2/2 transceiver arrangement and 120 kbit/s speed class as the MAX232EIDRG4, making it the closest identified same-footprint replacement. The important functional difference is that the MAX232EIDRG4 is identified as having IEC 61000-4-2 protection, while the MAX232IDRG4 listing does not state that protection. Confirm every electrical and protection parameter against both datasheets before substituting it in an exposed-port design.
What is the difference between MAX232EIDRG4 and MAX232IDRG4?
The principal documented difference is electrostatic-discharge protection: the MAX232EIDRG4 is specifically described as an RS-232 driver/receiver with IEC 61000-4-2 protection. Both devices are 16-SOIC, 2/2 RS-232 interface parts operating from 5 V and supporting 120 kbit/s communication. The MAX232IDRG4 should therefore be selected only after confirming its protection, supply-current, and electrical-limit requirements against the target system.
Can the MAX232ECSE replace the MAX232EIDRG4?
The MAX232ECSE is presented as a close MAX232E-series comparison candidate, but its complete pin and electrical compatibility must be verified before substitution. The MAX232EIDRG4 is a 16-pin SOIC device with two drivers, two receivers, 5 V operation, and 120 kbit/s performance. Compare package dimensions, exposed-pad status, charge-pump connections, ESD ratings, receiver thresholds, and absolute maximum ratings using the manufacturer datasheets.
When should I choose MAX232EIDRG4 instead of MAX232IDRG4?
Choose the MAX232EIDRG4 when an RS-232 port is exposed to electrostatic-discharge events and the design specifically benefits from its IEC 61000-4-2 protection. The MAX232IDRG4 may be appropriate for a protected enclosure where that protection is unnecessary. Both support the same headline 5 V, 2/2-channel, 120 kbit/s RS-232 function in a 16-SOIC package, so the choice should be driven by verified protection and worst-case electrical requirements.
Is MAX232EIDRG4 suitable for industrial equipment?
The MAX232EIDRG4 is suitable for many industrial serial interfaces because it supports -40 °C to +85 °C operation, ±30 V receiver inputs, and IEC 61000-4-2 protection. It is appropriate for service ports, controllers, and test equipment that use RS-232. The broader enclosure, grounding, surge protection, and isolation requirements still determine whether the interface is suitable for the complete installation.
How much supply current does MAX232EIDRG4 use?
The MAX232EIDRG4 is designed for low supply current while operating from a single 5 V supply, but a numeric current value is not stated in the available product information. Confirm the typical and maximum supply-current values in the Texas Instruments MAX232E electrical-characteristics table under the applicable load and charge-pump conditions. This measurement is important when sizing the rail and decoupling network.
Can MAX232EIDRG4 operate at 120 kbit/s?
Yes, the MAX232EIDRG4 operates to 120 kbit/s according to the Texas Instruments datasheet. It uses 1.0 µF charge-pump capacitors to support its single-supply RS-232 architecture. The usable UART rate still depends on cable length, connector wiring, grounding, electromagnetic interference, and the host-side baud-rate tolerance, so those factors should be checked separately.
What can replace MAX232EIDRG4?
The closest identified replacement is the MAX232IDRG4 because both are 16-SOIC, 2/2-channel RS-232 transceivers operating from 5 V at up to 120 kbit/s. The MAX232EIDRG4 adds a documented IEC 61000-4-2 protection feature, so substitution may change electrostatic-discharge resilience. Review pin assignments, supply current, receiver thresholds, driver levels, and protection ratings before approving a replacement.
Where can I buy MAX232EIDRG4 and request a quote?
Use the Request a Quote form on this product page to ask about MAX232EIDRG4 availability, order quantity, lead time, and package shipment requirements. Current stock and delivery terms can change, so request an updated quotation for the exact 16-SOIC MPN. Include the required quantities and target shipping location in the request for the most useful response.
What is the price of MAX232EIDRG4?
The current price of MAX232EIDRG4 should be requested through the Request a Quote form on this page because commercial terms and availability may change with quantity and shipment requirements. Quote the exact MPN, including the MAX232EIDRG4 suffix, so the response corresponds to the 16-SOIC device with IEC 61000-4-2 protection rather than another MAX232 package or ordering option.
What is the lead time for MAX232EIDRG4?
Request the current MAX232EIDRG4 lead time through the Request a Quote form on this page. Lead time depends on the exact ordering suffix, requested quantity, and available supply, none of which should be inferred from generic catalog listings. Include your production forecast and delivery schedule so the supplier can confirm the appropriate availability commitment.
Is MAX232EIDRG4 in stock?
Use the Request a Quote form on this page to obtain the current stock position for MAX232EIDRG4. Inventory at a reseller or distributor is not a guarantee that the exact suffix and package will remain available at the requested quantity. Provide your required order quantity, target date, and permitted substitutions so the supplier can respond with a firm availability statement.
Does MAX232EIDRG4 meet RoHS and REACH requirements?
The available product information identifies the MAX232EIDRG4 as RoHS and REACH compliant, but the certification documents are not reproduced in the technical listing. For a regulated production release, retain the manufacturer declarations and material-compliance records for the exact ordering suffix. The component is also described as operating from -40 °C to +85 °C, although environmental qualification beyond that range must be assessed separately.

এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা MAX232EIDRG4 — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।

নির্বাচন গাইড

Choose the MAX232EIDRG4 when the design needs two RS-232 channels, operation from a single 5 V supply, data rates up to 120 kbit/s, and documented IEC 61000-4-2 protection at an accessible connector. The MAX232IDRG4 is the closest identified alternative with the same 16-SOIC package and core communication ratings, but its protection rating and detailed electrical limits should be checked before substitution. Consider the MAX232ECSE when its exact ordering and temperature configuration meets the product requirements. For either alternative, verify pin assignments, charge-pump capacitor values, receiver thresholds, supply current, and absolute maximum ratings. If the port is exposed to severe surges, galvanic isolation, surge protection, and proper grounding may be required beyond the transceiver itself.

বিকল্পের সাথে তুলনা

পারামিটার এই পণ্য MAX232IDRG4 MAX232ECSE
Brand Texas Instruments Texas Instruments Texas Instruments
Package 16-SOIC 16-SOIC 16-SOIC

মূল পার্থক্যসমূহ

  • Documented electrostatic-discharge protection (বনামMAX232IDRG4)
  • Single-supply RS-232 operation (বনামMAX232IDRG4)
  • Broad industrial temperature coverage (বনামMAX232ECSE)

ডিজাইন নোট

Place the two 1.0 µF charge-pump capacitors close to their designated MAX232EIDRG4 pins, using the shortest possible connections and a solid ground return. Keep the RS-232 driver and receiver routes away from clocks, switching-regulator nodes, and sensitive analog inputs. Route each cable-side signal directly toward its connector, and provide a continuous ground reference between the transceiver and the RS-232 connector rather than relying on chassis ground alone.

Do not assume that the 120 kbit/s datasheet rating guarantees reliable communication over every cable length or baud rate. Confirm the UART oscillator tolerance, cable type, connector wiring, remote ground, and electromagnetic environment. Also verify the MAX232EIDRG4 data-direction assignments: an RS-232 driver output must connect to the remote receiver input, not to another driver output, because the interface is unbalanced and point-to-point.

Treat IEC 61000-4-2 protection as component-level ESD protection rather than a complete industrial surge solution. For long cables or an outdoor connector, add appropriate common-mode and surge protection, maintain protective-earth bonding, and use twisted-pair wiring. Keep the protected cable interface away from the 5 V supply entry point and high-current return paths to reduce differential noise and ground bounce.

Decouple the 5 V supply locally and verify the regulator's behavior during RS-232 driver transitions. The charge-pump network creates switching current internally, so a short supply loop and low-impedance ceramic bypass capacitor help prevent rail disturbance. Confirm the exact charge-pump capacitor tolerances and stability requirements in the manufacturer datasheet, and avoid adding long test pads or stubs to the protected interface lines.

কমপ্লায়েন্স তথ্য

RoHS
Compliant
REACH
Compliant
AEC-Q100
Not Applicable
লিড ফ্রি
Unknown
হ্যালোজেন ফ্রি
Unknown
কনফ্লিক্ট মিনারেলস
Unknown

RoHS and REACH compliance are stated for the MAX232EIDRG4. The available product information does not explicitly identify AEC-Q100 qualification, lead-free construction, halogen-free status, or conflict-minerals compliance.

ডেটা যাচাই করা হয়েছে: 2026-11-09 — ডেটা XAIPART-এর কম্পোনেন্ট ইঞ্জিনিয়ারিং টিম দ্বারা যাচাই ও কিউরেট করা হয়েছে

সম্পর্কিত অনুসন্ধান

MAX232EIDRG4 datasheet MAX232EIDRG4 pinout MAX232EIDRG4 datasheet pdf MAX232EIDRG4 equivalent MAX232EIDRG4 replacement MAX232EIDRG4 cross reference MAX232EIDRG4 vs MAX232IDRG4 MAX232EIDRG4 16-SOIC MAX232EIDRG4 120 kbit/s MAX232EIDRG4 IEC 61000-4-2 MAX232EIDRG4 application circuit MAX232EIDRG4 price MAX232EIDRG4 stock Texas Instruments MAX232EIDRG4 what is MAX232EIDRG4

সম্পর্কিত কম্পোনেন্ট ও শর্তাবলী

Texas Instruments MAX232EIDRG4 MAX232IDRG4 MAX232ECSE RS-232 RS-232 transceiver dual driver and receiver interface IC semiconductor charge-pump voltage converter electrostatic-discharge protection IEC 61000-4-2 TIA/RS-232-F ITU Recommendation V.28 RoHS REACH 16-pin SOIC SOIC package family surface-mount package 5 V power supply 120 kbit/s RS-232 port UART interface industrial control equipment
তাৎক্ষণিক বিলওয়াছে রেকোজিউইট
সম্পূর্ণ বিবরণ পূরণ করুন — আমাদের সেলস টিম 24 ঘণ্টার মধ্যে উত্তর দেবে
পার্ট নম্বর উৎপাদক প্যাকেজ QTY লক্ষ্যমূল্য প্রসারিত
✓
বিল প্রস্তুত করা হয়েছে!

আমরা ২৪ ঘণ্টার মধ্যে আপনার ইমেইলে প্রত্যুত্তর দেব

1
RFQ জমা হয়েছে
2
কোটেশন পাওয়া গেছে
3
অর্ডার দেওয়া হয়েছে
4
পেমেন্ট
5
শিপ করা হয়েছে
6
ডেলিভারি হয়েছে
RFQ বিবরণ দেখুন