MAX318CSA+ - SPST NO CMOS Analog Switch, 35 Ohm | Maxim
MPN: MAX318CSA+ ✓ সক্রিয়MAX318CSA+ সারাংশ
An analog switch is a solid-state, MOSFET-based signal router that connects or disconnects an analog signal path under digital control, sitting in the interface IC layer between sensors, converters and a system microcontroller. Unlike a mechanical relay, it switches in nanoseconds with negligible off-state leakage, making it the standard building block for sample-and-hold front ends, programmable gain stages, test-point muxes and isolated-signal routing.
Key characteristics of the MAX318CSA+ include a maximum on-resistance of 35 Ohm, on-resistance matching held within 2 Ohm between channels and variation of only 3 Ohm maximum across the analog signal range, and very low leakage of less than 250 pA at +25 degC rising to less than 6 nA at +85 degC. The part is listed in production by Analog Devices and is specified over a 0 degC to +70 degC commercial temperature range in the SOIC package.
Internally the device uses CMOS transmission gates, so the signal path is symmetrical and the switch behaviour does not depend on the control polarity in the same way a bipolar multiplexer does. The small, flat on-resistance curve preserves signal integrity for low-frequency analog signals, while the low leakage keeps the off-state contribution to system error negligible when a single measurement or sensor node is selected.
Typical uses include routing sensor outputs into a single ADC input, multiplexing discrete resistive networks into a programmable gain amplifier, isolating a precision reference from a measurement node, selecting between test points during board bring-up, and building small sample-and-hold front ends in instrumentation equipment. Any of these functions can also be handled with a relay, but the CMOS switch removes the slow mechanical switching time and the contact bounce that plague relay-based solutions at higher cycle rates.
When laying out the MAX318CSA+, place the device close to the source and destination of the analog path so that the switched trace stays short and the 35 Ohm series resistance has the least effect on signal settling. Keep the supply decoupling capacitor adjacent to the V+ and ground pins, and route control traces away from the analog node where board area allows, because charge injection through the control line can create a transient step at the moment of switching.
This page consolidates the distributor availability picture, the family-level drop-in alternatives in the same 8-SOIC footprint, and the practical routing and layout notes that engineers usually have to piece together from the manufacturer data sheet and application experience.
এর জন্য ড্রপ-ইন বিকল্প MAX318CSA+ — একই package, pin-to-pin compatible। ভিন্ন package-এর যেসব পার্টে PCB rework প্রয়োজন সেগুলো বাদ দেওয়া হয়েছে।
MAX318ESA+
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
MAX318CSA+T
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
MAX318ESA+T
✅ ড্রপ-ইন ⚠️ স্পেক যাচাইকৃত নয়📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
MAX318CSA-T
✅ ড্রপ-ইন📋 রেফারেন্স বিকল্প (ক্যাটালগে নেই)
MAX318CSA+ সর্বোচ্চ রেটিং ও বৈদ্যুতিক বৈশিষ্ট্য
| Switch Configuration | SPST (single-pole single-throw), 1:1 multiplexer |
| Switch State | Normally open (NO) |
| Number of Circuits | 1 |
| On-Resistance (max) | 35 Ohm |
| On-Resistance Matching Between Channels | Within 2 Ohm |
| On-Resistance Variation Over Signal Range | 3 Ohm max |
| Off-State Leakage at +25 degC | Less than 250 pA |
| Off-State Leakage at +85 degC | Less than 6 nA |
| পিনের সংখ্যা | 8 |
| প্যাকেজ | 8-SOIC (NSOIC) |
| মাউন্টিং টাইপ | Surface mount |
| অপারেটিং তাপমাত্রার পরিসর | 0 degC to +70 degC |
| Process Technology | Precision CMOS |
| লাইফসাইকেল স্ট্যাটাস | Production (per manufacturer product page) |
| RoHS স্ট্যাটাস | Compliant |
| Manufacturer Listed Lead Time | 10 weeks (per distributor listing) |
MAX318CSA+ 8-soic (nsoic) পিন কনফিগারেশন গাইড
MAX318CSA+ (8-soic (nsoic) প্যাকেজ)-এর পিন কনফিগারেশন। পিন নম্বরিং, ফাংশন এবং সংযোগ ডায়াগ্রাম প্রস্তুতকারকের ডেটাশিটে সংজ্ঞায়িত করা আছে। সঠিক ফুটপ্রিন্ট এবং সোল্ডারিং নির্দেশিকার জন্য এটি দেখুন।
এর জন্য বিস্তারিত পিনআউট ডেটা পাওয়া যায়নি MAX318CSA+.
দেখুন ডেটাশিট সম্পূর্ণ পিন কনফিগারেশনের জন্য।
সাধারণ ব্যবহার
MAX318CSA+ এর জন্য উপযুক্ত 6 অ্যাপ্লিকেশনs: Precision ADC Front-End Sensor Multiplexer, Programmable Gain and Feedback Network Switching, Sample-and-Hold and Instrumentation Multiplexing, Battery-Powered Portable Sensor Terminals, Test Point Selection and Board Bring-Up, Audio and Low-Level Signal Routing.
Precision ADC Front-End Sensor Multiplexer
The MAX318CSA+ suits designs that must bring several low-level sensor outputs into one conversion channel. Because the switch adds at most 35 Ohm in series and leaks less than 250 pA at +25 degC when open, the error it injects into a high-impedance sensor node is well below the noise floor of most resistive or capacitive sensors. Use it to place one thermocouple, bridge output or strain-gauge channel at a time onto the input of a precision SAR ADC such as the ADS1262IPW, with the on/off control driven by the host MCU. The flat on-resistance curve, varying no more than 3 Ohm across the signal range, keeps the switched-node gain error independent of input level. Add a small hold capacitor at the ADC input when the source impedance is high, so that the switch capacitance can settle within the acquisition window.
সুপারিশকৃত
Programmable Gain and Feedback Network Switching
In programmable-gain and feedback topologies, the MAX318CSA+ can select between discrete resistive networks without changing the amplifier gain stability analysis in a fundamental way. Switching a 35 Ohm series element in front of a high-impedance amplifier input adds only a small, predictable series term, while the leakage of less than 250 pA at +25 degC keeps the input bias error negligible relative to the resistor network itself. This makes the part suitable for gain-ranging stages built around precision amplifiers such as the AD8015ARZ, where the gain set must change under software control. Because the resistance is flat across the analog signal range, gain accuracy does not drift as the input signal rises. Keep the switched network ground-referenced close to the switch ground pin to prevent switching transients from modulating the amplifier input.
সুপারিশকৃত
Sample-and-Hold and Instrumentation Multiplexing
The MAX318CSA+ is well suited to building compact sample-and-hold front ends in bench and field instrumentation, where a mechanical relay would be too slow. The CMOS transmission gate switches in nanoseconds and its off-state leakage of less than 250 pA at +25 degC keeps the held capacitor from discharging quickly, which is what makes a switched-capacitor hold stage practical. Route the switched node into a precision buffer such as the AD7492ARZ, a low-noise ADC driver, so that the hold capacitor sees a high input impedance rather than the switch itself. The 35 Ohm series resistance adds only a small settling term to the RC time constant, so a moderate hold capacitance is usually sufficient. Confirm the supply voltage limits and control-logic levels in the manufacturer data sheet before finalising the hold timing.
সুপারিশকৃত
Battery-Powered Portable Sensor Terminals
In battery-powered field terminals and IoT sensor nodes, the MAX318CSA+ lets one analog input pin serve several sensing channels, which reduces both board area and the number of pins on a constrained microcontroller. The off-state leakage of less than 250 pA at +25 degC is negligible against the microamp-level standby currents typical of portable equipment, and the CMOS switch adds no significant quiescent current beyond its own control logic. A single SPST normally-open device is ideal for routing a reference or a thermistor line to a shared ADC when the system does not need fail-safe or SPDT behaviour. Because the switch sits between a long sensor trace and the converter input, place it near the converter to keep the switched section short and shielded from the field wiring that may pick up noise.
সুপারিশকৃত
Test Point Selection and Board Bring-Up
The MAX318CSA+ provides a simple way to route several test points to a single measurement channel during board bring-up, functional test and production calibration. A CMOS analog switch isolates the nodes it is not selecting, so the leakage of less than 250 pA at +25 degC does not drag the measurement of an adjacent high-impedance node. Switching speeds in the nanosecond range let a tester scan nodes rapidly without the settling penalty of an electromechanical relay. Use the part to isolate a precision reference from a measurement node when the reference must remain undisturbed during a calibration sweep, and to select between an internal and external clock or reference in a mixed-signal board. Keep the control traces short and route them away from the sensitive analog pads during layout.
সুপারিশকৃত
Audio and Low-Level Signal Routing
For low-level audio and baseband signal routing, the MAX318CSA+ can be used as a mute or source-select element in small-signal paths. Its low off-state leakage of less than 250 pA at +25 degC means that an open switch contributes negligibly to the input impedance of the following stage, and the on-resistance of 35 Ohm is acceptable when the source impedance is of the order of hundreds of ohms. Precision amplifiers such as the AD8016ARP or AD8018ARZ can sit behind the switch for headphone and line-level buffering, with the switch selecting between two sources or muting the chain. The flat on-resistance characteristic, varying 3 Ohm maximum over the signal range, means the gain error introduced is essentially independent of level, which keeps channel-to-channel matching predictable in stereo or multi-zone audio paths.
সুপারিশকৃত
সুপারিশকৃত পণ্যের সারসংক্ষেপ
এর জন্য ইঞ্জিনিয়ারিং রেফারেন্স ডেটা MAX318CSA+ — তুলনা, ডিজাইন গাইডেন্স এবং কমপ্লায়েন্স তথ্য।
নির্বাচন গাইড
বিকল্পের সাথে তুলনা
| পারামিটার | এই পণ্য | MAX318ESA+ | MAX318CSA+T | MAX318ESA+T | MAX318CSA-T |
|---|---|---|---|---|---|
| Package | 8-SOIC (NSOIC) | 8-SOIC (NSOIC) - same | 8-SOIC (NSOIC) - same | 8-SOIC (NSOIC) - same | 8-SOIC (NSOIC) - same |
| Brand | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated | Maxim Integrated |
| Switch Configuration | SPST, 1 circuit, normally open | SPST, 1 circuit, normally open | SPST, 1 circuit, normally open | SPST, 1 circuit, normally open | SPST, 1 circuit, normally open |
| On-Resistance (max) | 35 Ohm | 35 Ohm | 35 Ohm | 35 Ohm | 35 Ohm |
| Off-State Leakage at +25 degC | Less than 250 pA | Less than 250 pA | Less than 250 pA | Less than 250 pA | Less than 250 pA |
| Off-State Leakage at +85 degC | Less than 6 nA | Less than 6 nA | Less than 6 nA | Less than 6 nA | Less than 6 nA |
| Operating Temperature Range | 0 degC to +70 degC | -40 degC to +85 degC (extended) | 0 degC to +70 degC | -40 degC to +85 degC (extended) | 0 degC to +70 degC |
| On-Resistance Matching Between Channels | Within 2 Ohm | Within 2 Ohm | Within 2 Ohm | Within 2 Ohm | Within 2 Ohm |
| On-Resistance Variation Over Signal Range | 3 Ohm max | 3 Ohm max | 3 Ohm max | 3 Ohm max | 3 Ohm max |
| Packaging Form | 8-SOIC, commercial grade ordering code | 8-SOIC, extended grade, tube | 8-SOIC, tape and reel | 8-SOIC, extended grade, tape and reel | 8-SOIC, legacy tape and reel |
মূল পার্থক্যসমূহ
- Extended-temperature sibling available in the identical footprint (বনামMAX318ESA+)
- Low off-state leakage keeps the switched node effectively unloaded (বনামMechanical relay alternative)
- Flat on-resistance keeps gain error independent of signal level (বনামDiscrete MOSFET switch implementation)
- Ordering and packaging flexibility from the same die (বনামMAX318CSA-T)
ডিজাইন নোট
Keep the switched analog path short: place the MAX318CSA+ so the trace from the switch to the destination node is as short as possible, because the 35 Ohm maximum on-resistance acts in series with the source impedance and adds to settling time. Route the control line away from the analog pad, and connect the ground reference of the switch close to the device ground pin so that charge injection from the control transition returns locally instead of through the sensitive analog return path.
Do not treat the MAX318 family members as interchangeable. MAX318 is normally open, MAX317 is normally closed, and MAX319 is single-pole double-throw; only the same switching behaviour can be dropped into an existing board without changing the control logic. Confirm the required switch state, the supply voltage limits and the control logic levels in the manufacturer data sheet before fitting any ordering code of the family.
At the input of a high-impedance node the off-state leakage of less than 250 pA at +25 degC is usually negligible, but the on-state 35 Ohm plus the switch capacitance can slow the acquisition of a high-impedance source. If the ADC settling window is tight, add a small hold capacitor at the destination node and re-check the acquisition time with the switch capacitance included. The on-resistance flatness of 3 Ohm maximum across the signal range keeps the gain error level-independent.
Place the supply bypass capacitor immediately adjacent to the supply and ground pins of the device, and keep the supply decoupling loop as small as possible. Switching transients produced at the moment of turn-on are supplied locally in this way, preventing them from modulating the reference or the analog bus elsewhere on the board. Use a ceramic capacitor chosen per the decoupling guidance in the manufacturer data sheet for the operating frequency range of your system.
কমপ্লায়েন্স তথ্য
RoHS compliance is indicated on the distributor series listing for the MAX318 family; the + suffix on the ordering code denotes the lead-free termination. No AEC-Q100 qualification is claimed for this part, and no REACH, halogen-free or conflict-minerals declaration was available for the MAX318CSA+.